ABPX1101 Advanced Programmable Clock FEATURES * * * XIN/FIN 1 GND 2 CLK0 3 CLK1 4 8 XOUT 7 CLK2,OE,PDB,FSEL 6 NC 5 VDD SOP-8 MSOP-8 CLK0 1 GND 2 XIN/FIN 3 ABPX1101 * * Advanced programmable PLL design Very low Jitter and Phase Noise (30-70ps Pk-Pk typical) Up to 3 programmable outputs Two registers banks for 2-time programming. Output frequency up to 200MHz CMOS. Accepts Crystal or reference clock inputs o Fundamental crystal: 10MHz-30MHz o 3 RD overtone crystal: Up to 75MHz o Reference input: Up to 200MHz Accepts <1.0V reference signal input voltage One programmable I/O pin can be configured as Programmable clock, or Frequency Selection input, or output Enable (OE) or Power Down (PDB) input. Single 2.5V or 3.3V 10% power supply Operating temperature range from -40C to 85C Available in 8-pin MSOP/SOIC, and 6-pin SOT ABPX1101 * * * * * * PIN CONFIGURATION 6 VDD 5 CLK2,OE,PDB,FSEL 4 XOUT SOT-23 DESCRIPTION The ABPX1101 is a low-cost general purpose frequency synthesizer and a member of Abracons' Advanced Programmable Clock family. Abracon's ABPX1101 product family offers the versatility of using a single Crystal or Reference Clock input and producing up to three different system clocks. They can generate any output frequency up to 200 MHz from fundamental crystal input between 10 MHz - 30 MHz, or a 3rd overtone crystal of up to 75Mhz, or a Reference clock input of up to 200 MHz. Cascading of the ICs to produce additional clock frequencies is also supported. BLOCK DIAGRAM XIN/FIN Xtal OSC XOUT FRef R-counter (8-bit) Phase Detector Charge Pump Loop Filter M -counter (10-bit) FVCO = F Ref. * (2 * M /R) OE PDB CLoad Programming Logic FSEL VCO P-counter (5-bit) Fout = FVCO / (2 * P) Selectable /1,/2,/4,/8 CLOCK[0:2] Selectable /1,/2 Programmable Function 30332 Esperanza., Rancho Santa Margarita, Ca 92688 Ph: 949-546-8000 Fax: 949-546-8001 www.Abracon.com 03/15/05 Page 1 ABPX1101 Advanced Programmable Clock KEY PROGRAMMING PARAMETERS CLK[ 0:2 ] Output Frequency Output Drive Strength Fout = FIN * M / (R * P) where M=10 bit R= 8 bit P= 5 bit 1. CLK[0:2]= Fout/[1,2,4,8] 2. CLK[0:2]= FIN or FIN/2 Std: 10mA (default) High: 24mA Crystal Load # of Register Banks Programmable Input/Output +/- 200ppm One output pin can tuning. be configured as 1. CLK2 - output 2. FSEL - input 3. OE - input 4. PDB - input 2 ChargePump Current 4 levels of pump current settings PIN DESCRIPTION Name Pin # MSOP-8 SOT-23 SOIC-8 Type Description XIN/FIN 1 3 I Crystal or Reference input pin GND 2 2 P GND connection CLK[0:1] 3,4 1 O Programmable Clock Output VDD 5 6 P VDD connection (2.25~3.63V) NC 6 No Connect This programmable I/O pin can be configured as a programmable clock output (CLK2), or Output Enable (OE) input, or Power Down input (PDB), or Frequency Selection (FSEL) input pin. This pin has an internal 60K pull up resistor. CLK2, OE, PDB, FSEL 7 5 B State 0 1 (default) XOUT 8 4 O OE PDB FSEL Tristate Power Down Mode Select Bank '0' ROM Normal mode Select Bank `1' ROM CLK[0:1] Normal mode Crystal output pin 30332 Esperanza., Rancho Santa Margarita, Ca 92688 Ph: 949-546-8000 Fax: 949-546-8001 www.Abracon.com 03/15/05 Page 2 ABPX1101 Advanced Programmable Clock ELECTRICAL SPECIFICATIONS ABSOLUTE MAXIMUM RATINGS PARAMETERS SYMBOL MIN. MAX. UNITS V DD - 0.5 4.6 V Input Voltage Range VI - 0.5 V DD + 0.5 V Output Voltage Range VO - 0.5 V DD + 0.5 V 260 C Supply Voltage Range Soldering Temperature (Green package) 10 Data Retention @ 85C Storage Temperature TS Ambient Operating Temperature Year -65 150 C -40 85 C Exposure of the device under conditions beyond the limits specified by Maximum Ratings for extended periods may cause permanent damage to the device and affect product reliability. These conditions represent a stress rating only, and functional operations of the device at these or any other conditions above the operational limits noted in this specification is not implied. AC SPECIFICATIONS PARAMETERS Crystal Input Frequency(XIN) CONDITIONS Fundamental Crystal MIN. TYP. 10 3 rd Overtone Crystal Input (FIN) Frequency Input (FIN) Signal Amplitude Internally AC coupled Settling Time At power-up (after VDD increases over 1.62V) Output Rise Time Output Fall Time 0.9 MAX. UNITS 30 MHz 75 MHz 200 MHz VDD Vpp 10 ms 15pF Load, 10/90%VDD, Standard drive 2.5 3.5 ns 15pF Load, 10/90%VDD, High drive 1.0 1.5 ns 15pF Load, 90/10%VDD, Standard drive 2.5 3.5 ns 15pF Load, 90/10%VDD, High drive 1.0 1.5 ns 50 55 % 500 ps Duty Cycle At VDD/2 Max. output skew between same frequency clocks Equal loading (15 pF). Equal frequency & drive strength Period Jitter, peak-to-peak* (measured from 10,000 samples) With capacitive decoupling between VDD and GND. Operating only one output. 45 70 ps * Note: Jitter performance depends on the programming parameters. 30332 Esperanza., Rancho Santa Margarita, Ca 92688 Ph: 949-546-8000 Fax: 949-546-8001 www.Abracon.com 03/15/05 Page 3 ABPX1101 Advanced Programmable Clock DC SPECIFICATIONS PARAMETERS SYMBOL CONDITIONS MIN. TYP. At 10MHz, load=15pF MAX. UNITS 15 mA 5 A 3.63 V 0.4 V Supply Current, Dynamic, with Loaded Outputs I DD Operating Voltage V DD Output Low Voltage V OL Output High Voltage V OH Output Current, Standard drive I OSD V OL = 0.4V, V OH = 2.4V 10.7 mA Output Current, High drive I OHD V OL = 0.4V, V OH = 2.4V 24 mA (PDB=1) PDB=0 Short-circuit Current 2.25 I OL = +4mA Standard drive I OH = -4mA V DD - 0.4 Standard drive IS V 50 mA CRYSTAL SPECIFICATIONS PARAMETERS SYMBOL MIN. Fundamental Crystal Resonator Frequency F XIN 10 3rd Overtone Crystal Resonator Frequency F XIN Crystal Loading Rating (The IC can be programmed for any value in this range.) C L (xtal) TYP. 5 Maximum Sustainable Drive Level Operating Drive Level Crystal Shunt Capacitance MAX. UNITS 30 MHz 75 MHz 20 pF 500 W W 100 C0 6 pF Effective Series Resistance, Fundamental, 10-30MHz ESR 30 Effective Series Resistance, 3 rd Overtone, 30-50MHz [CO< 4pF, C L =(5pF)/(8pF)] ESR 100/70 Effective Series Resistance, 3 rd Overtone, 50-65MHz, [CO< 4pF, C L =5pF(5pF)/(8pF)] ESR 60/40 Effective Series Resistance, 3 rd Overtone, 65-75MHz [CO< 4pF, C L =(5pF)/(8pF)] ESR 45/30 Note: A detailed crystal specification document is also available for this part 30332 Esperanza., Rancho Santa Margarita, Ca 92688 Ph: 949-546-8000 Fax: 949-546-8001 www.Abracon.com 03/15/05 Page 4 ABPX1101 Advanced Programmable Clock PACKAGE DRAWINGS (GREEN PACKAGE COMPLIANT) MSOP 8L Symbol A A1 A2 B C D E H L e Dimension in MM Min. Max. --1.10 0.05 0.15 0.81 0.91 0.25 0.40 0.13 0.23 2.90 3.10 2.90 3.10 4.90 BSC 0.445 0.648 0.65 BSC E H D A2 A A1 C L b e SOIC 8L Symbol A A1 A2 B C D E H L e Dimension in MM Min. Max. 1.35 1.75 0.10 0.25 1.25 1.50 0.33 0.53 0.19 0.27 4.80 5.00 3.80 4.00 5.80 6.20 0.40 0.89 1.27 BSC E H D A2 A A1 C L b e SOT-23 6 L Symbol A A1 A2 B C D E H L e Dimension in MM Min. Max. 1.05 1.35 0.05 0.15 1.00 1.20 0.30 0.50 0.08 0.20 2.80 3.00 1.50 1.70 2.60 3.0 0.35 0.55 0.95 BSC E H D A2 A A1 C e b L 30332 Esperanza., Rancho Santa Margarita, Ca 92688 Ph: 949-546-8000 Fax: 949-546-8001 www.Abracon.com 03/15/05 Page 5 ABPX1101 Advanced Programmable Clock ORDERING INFORMATION For part ordering, please contact our Sales Department: 30332 Esperanza., Rancho Santa Margarita, Ca 92688 Ph: 949-546-8000 Fax: 949-546-8001 PART NUMBER The order number for this device is a combination of the following: Device number, Package type and Operating temperature range ABPX1101-XXX X X-X PART NUMBER 3 DIGIT ID Code * NONE= TUBE T=TAPE and REEL PACKAGE TYPE S=SOIC M=MSOP T=SOT TEMPERATURE C=COMMERCIAL I = INDUSTRIAL * Abracon will assign a unique 3-digit ID code for each approved programmed part number. * Abracon offers Green Package Only for this product family. Part / Order Number* Marking Package Option ABPX1101-XXXSC A1XXX 8-Pin SOIC (Tube) ABPX1101-XXXSC-T A1XXX 8-Pin SOIC (Tape and Reel) ABPX1101-XXXMC A1XXX 8-Pin MSOP (Tube) ABPX1101-XXXMC-T A1XXX 8-Pin MSOP (Tape and Reel) ABPX1101-XXXTC-T A1XXX 6-Pin SOT-23 (Tape and Reel) * Ordering will include Programming ID number that will be supplied at the time the samples are provided. Abracon Corporation, reserves the right to make changes in its products or specifications, or both at any time without notice. The information furnished by Abracon is believed to be accurate and reliable. However, Abracon makes no guarantee or warranty concerning the accuracy of said information and shall not be responsible for any loss or damage of whatever nature resulting from the use of, or reliance upon this product. LIFE SUPPORT POLICY: Abracon's products are not authorized for use as critical components in life support devices or systems without the express written approval of the President of Abracon Corporation. 30332 Esperanza., Rancho Santa Margarita, Ca 92688 Ph: 949-546-8000 Fax: 949-546-8001 www.Abracon.com 03/15/05 Page 6