ATTINY25-15SZ - Atmel - Datasheet.Support

Features

•High Performance, Low Power AVR® 8-Bit Microcontroller

•Advanced RISC Architecture

– 120 Powerful Instructions – Most Single Clock Cycle Execution

– 32 x 8 General Purpose Working Registers

– Fully Static Operation

•Non-volatile Program and Data Memories

– 2/4/8K Byte of In-System Programmable Program Memory Flash (ATtiny25/45/85)

Endurance: 10,000 Write/Erase Cycles

– 128/256/512 Bytes In-System Programmable EEPROM (ATtiny25/45/85)

Endurance: 100,000 Write/Erase Cycles

– 128/256/512 Bytes Internal SRAM (ATtiny25/45/85)

– Programming Lock for Self-Programming Flash Program and EEPROM Data

Security

•Peripheral Features

– 8-bit Timer/Counter with Prescaler and Two PWM Channels

– 8-bit High Speed Timer/Counter with Separate Prescaler

2 High Frequency PWM Outputs with Separate Output Compare Registers

Programmable Dead Time Generator

– Universal Serial Interface with Start Condition Detector

– 10-bit ADC

4 Single Ended Channels

2 Differential ADC Channel Pairs with Programmable Gain (1x, 20x)

– Programmable Watchdog Timer with Separate On-chip Oscillator

– On-chip Analog Comparator

•Special Microcontroller Features

– debugWIRE On-chip Debug System

– In-System Programmable via SPI Port

– External and Internal Interrupt Sources

– Low Power Idle, ADC Noise Reduction, and Power-down Modes

– Enhanced Power-on Reset Circuit

– Programmable Brown-out Detection Circuit

– Internal Calibrated Oscillator

•I/O and Packages

– Six Programmable I/O Lines

– 8-pin PDIP and 8-pin SOIC

•Operating Voltage

– 1.8 - 5.5V for ATtiny25/45/85V

– 2.7 - 5.5V for ATtiny25/45/85

•Speed Grade

– ATtiny25/45/85V: 0 - 4 MHz @ 1.8 - 5.5V, 0 - 10 MHz @ 2.7 - 5.5V

– ATtiny25/45/85: 0 - 10 MHz @ 2.7 - 5.5V, 0 - 20 MHz @ 4.5 - 5.5V

•Industrial Temperature Range

•Low Power Consumption

– Active Mode:

1 MHz, 1.8V: 450µA

– Power-down Mode:

0.1µA at 1.8V

8-bit

Microcontroller

with 2/4/8K

Bytes In-System

Programmable

Flash

ATtiny25/V

ATtiny45/V

ATtiny85/V

Preliminary

Summary

2586AS–AVR–02/05

Note: This is a summary document. A complete document

is available on our Web site at www.atmel.com.

2586AS–AVR–02/05

ATtiny25/45/85

1. Pin Configurations

Figure 1-1. Pinout ATtiny25/45/85

1.1 Disclaimer

Typical values contained in this data sheet are based on simulations and characterization of other AVR microcontrollers

manufactured on the same process technology. Min and Max values will be available after the device is characterized.

(PCINT5/RESET/ADC0/dW) PB5

(PCINT3/XTAL1/OC1B/ADC3) PB3

(PCINT4/XTAL2/CLKO/OC1B/ADC2) PB4

GND

VCC

PB2 (SCK/USCK/SCL/ADC1/T0/INT0/PCINT2)

PB1 (MISO/DO/AIN1/OC0B/OC1A/PCINT1)

PB0 (MOSI/DI/SDA/AIN0/OC0A/OC1A/AREF/PCINT0)

PDIP/SOIC

2586AS–AVR–02/05

ATtiny25/45/85

2. Overview

The ATtiny25/45/85 is a low-power CMOS 8-bit microcontroller based on the AVR enhanced

RISC architecture. By executing powerful instructions in a single clock cycle, the ATtiny25/45/85

achieves throughputs approaching 1 MIPS per MHz allowing the system designer to optimize

power consumption versus processing speed.

2.1 Block Diagram

Figure 2-1. Block Diagram

The AVR core combines a rich instruction set with 32 general purpose working registers. All the

32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing two independent

PROGRAM

COUNTER

INTERNAL

OSCILLATOR

WATCHDOG

TIMER

STACK

POINTER

PROGRAM

FLASH SRAM

MCU CONTROL

GENERAL

PURPOSE

REGISTERS

INSTRUCTION

TIMER/

COUNTER0

SERIAL

UNIVERSAL

INTERFACE

TIMER/

COUNTER1

INSTRUCTION

DECODER

DATA DIR.

REG.PORT B

DATA REGISTER

PORT B

PROGRAMMING

LOGIC

TIMING AND

CONTROL

MCU STATUS

STATUS

ALU

PORT B DRIVERS

PB0-PB5

VCC

GND

CONTROL

LINES

8-BIT DATABUS

ADC /

ANALOG COMPARATOR

INTERRUPT

UNIT

DATA

EEPROM

CALIBRATED

OSCILLATORS

RESET

2586AS–AVR–02/05

ATtiny25/45/85

registers to be accessed in one single instruction executed in one clock cycle. The resulting

architecture is more code efficient while achieving throughputs up to ten times faster than con-

ventional CISC microcontrollers.

The ATtiny25/45/85 provides the following features: 2/4/8K byte of In-System Programmable

Flash, 128/256/512 bytes EEPROM, 128/256/256 bytes SRAM, 6 general purpose I/O lines, 32

general purpose working registers, one 8-bit Timer/Counter with compare modes, one 8-bit high

speed Timer/Counter, Universal Serial Interface, Internal and External Interrupts, a 4-channel,

10-bit ADC, a programmable Watchdog Timer with internal Oscillator, and three software select-

able power saving modes. The Idle mode stops the CPU while allowing the SRAM,

Timer/Counter, ADC, Analog Comparator, and Interrupt system to continue functioning. The

Power-down mode saves the register contents, disabling all chip functions until the next Inter-

rupt or Hardware Reset. The ADC Noise Reduction mode stops the CPU and all I/O modules

except ADC, to minimize switching noise during ADC conversions.

The device is manufactured using Atmel’s high density non-volatile memory technology. The

On-chip ISP Flash allows the Program memory to be re-programmed In-System through an SPI

serial interface, by a conventional non-volatile memory programmer or by an On-chip boot code

running on the AVR core.

The ATtiny25/45/85 AVR is supported with a full suite of program and system development tools

including: C Compilers, Macro Assemblers, Program Debugger/Simulators, In-Circuit Emulators,

and Evaluation kits.

2.2 Pin Descriptions

2.2.1 VCC

Supply voltage.

2.2.2 GND

Ground.

2.2.3 Port B (PB5..PB0)

Port B is a 6-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The

Port B output buffers have symmetrical drive characteristics with both high sink and source

capability. As inputs, Port B pins that are externally pulled low will source current if the pull-up

resistors are activated. The Port B pins are tri-stated when a reset condition becomes active,

even if the clock is not running.

Port B also serves the functions of various special features of the ATtiny25/45/85 as listed on

page 60.

On the ATtiny25 device the programmable I/O ports PB3 and PB4 (pins 2 and 3) are exchanged

in the ATtiny15 compatibility mode for supporting the backward compatibility with ATtiny15.

2.2.4 RESET

Reset input. A low level on this pin for longer than the minimum pulse length will generate a

reset, even if the clock is not running. The minimum pulse length is given in Table 8-1 on page

37. Shorter pulses are not guaranteed to generate a reset.

2586AS–AVR–02/05

ATtiny25/45/85

3. Register Summary

Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Page

0x3F SREG I T H S V N Z C page 7

0x3E SPH – – – – – – – SP8 page 10

0x3D SPL SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 page 10

0x3C Reserved –

0x3B GIMSK – INT0 PCIE – – – – – page 49

0x3A GIFR – INTF0 PCIF – – – – – page 50

0x39 TIMSK – OCIE1A OCIE1B OCIE0A OCIE0B TOIE1 TOIE0 –page 81

0x38 TIFR – OCF1A OCF1B OCF0A OCF0B TOV1 TOV0 –page 81

0x37 SPMCSR – – – CTPB RFLB PGWRT PGERS SPMEN page 146

0x36 Reserved –

0x35 MCUCR –PUDSESM1SM0 –ISC01ISC00page 32, page 60, page 49

0x34 MCUSR – – – – WDRF BORF EXTRF PORF page 40,

0x33 TCCR0B FOC0A FOC0B –– WGM02 CS02 CS01 CS00 page 79

0x32 TCNT0 Timer/Counter0 page 80

0x31 OSCCAL Oscillator Calibration Register page 27

0x30 TCCR1 CTC1 PWM1A COM1A1 COM1A0 CS13 CS12 CS11 CS10 page 88, page 100

0x2F TCNT1 Timer/Counter1 page 90, page 101

0x2E OCR1A Timer/Counter1 Output Compare Register A page 90, page 102

0x2D OCR1C Timer/Counter1 Output Compare Register C page 91, page 102

0x2C GTCCR TSM PWM1B COM1B1 COM1B0 FOC1B FOC1A PSR1 PSR0 page 84, page 89, page

0x2B OCR1B Timer/Counter1 Output Compare Register B page 91

0x2A TCCR0A COM0A1 COM0A0 COM0B1 COM0B0 –WGM01 WGM00 page 76

0x29 OCR0A Timer/Counter0 – Output Compare Register A page 80

0x28 OCR0B Timer/Counter0 – Output Compare Register B page 80

0x27 PLLCSR SM –––– PCKE PLLE PLOCK page 93, page 103

0x26 CLKPR CLKPCE – – – CLKPS3 CLKPS2 CLKPS1 CLKPS0 page 30

0x25 DT1A DT1AH3 DT1AH2 DT1AH1 DT1AH0 DT1AL3 DT1AL2 DT1AL1 DT1AL0 page 108

0x24 DT1B DT1BH3 DT1BH2 DT1BH1 DT1BH0 DT1BL3 DT1BL2 DT1BL1 DT1BL0 page 109

0x23 DTPS1 - - - - - - DTPS11 DTPS10 page 108

0x22 DWDR DWDR[7:0] page 143

0x21 WDTCR WDTIF WDTIE WDP3 WDCE WDE WDP2 WDP1 WDP0 page 42

0x20 PRR –PRTIM1 PRTIM0 PRUSI PRADC page 33

0x1F EEARH EEAR8 page 16

0x1E EEARL EEAR7 EEAR6 EEAR5 EEAR4 EEAR3 EEAR2 EEAR1 EEAR0 page 16

0x1D EEDR EEPROM Data Register page 16

0x1C EECR –– EEPM1 EEPM0 EERIE EEMWE EEWE EERE page 17

0x1B Reserved –

0x1A Reserved –

0x19 Reserved –

0x18 PORTB –– PORTB5 PORTB4 PORTB3 PORTB2 PORTB1 PORTB0 page 64

0x17 DDRB –– DDB5 DDB4 DDB3 DDB2 DDB1 DDB0 page 64

0x16 PINB –– PINB5 PINB4 PINB3 PINB2 PINB1 PINB0 page 64

0x15 PCMSK –– PCINT5 PCINT4 PCINT3 PCINT2 PCINT1 PCINT0 page 51

0x14 DIDR0 –– ADC0D ADC2D ADC3D ADC1D EIN1D AIN0D page 124, page 141

0x13 GPIOR2 General Purpose I/O Register 2

0x12 GPIOR1 General Purpose I/O Register 1

0x11 GPIOR0 General Purpose I/O Register 0

0x10 USIBR USI Buffer Register page 118

0x0F USIDR USI Data Register page 117

0x0E USISR USICIF USIOIF USIPF USIDC USICNT3 USICNT2 USICNT1 USICNT0 page 118

0x0D USICR USISIE USIOIE USIWM1 USIWM0 USICS1 USICS0 USICLK USITC page 119

0x0C Reserved –

0x0B Reserved –

0x0A Reserved –

0x09 Reserved –

0x08 ACSR ACD ACBG ACO ACI ACIE –ACIS1 ACIS0 page 122

0x07 ADMUX REFS1 REFS0 ADLAR REFS2 MUX3 MUX2 MUX1 MUX0 page 137

0x06 ADCSRA ADEN ADSC ADATE ADIF ADIE ADPS2 ADPS1 ADPS0 page 138

0x05 ADCH ADC Data Register High Byte page 140

0x04 ADCL ADC Data Register Low Byte page 140

0x03 ADCSRB BIN ACME IPR –– ADTS2 ADTS1 ADTS0 page 122, page 140

0x02 Reserved –

0x01 Reserved –

0x00 Reserved –

2586AS–AVR–02/05

ATtiny25/45/85

Note: 1. For compatibility with future devices, reserved bits should be written to zero if accessed. Reserved I/O memory addresses

should never be written.

2. I/O Registers within the address range 0x00 - 0x1F are directly bit-accessible using the SBI and CBI instructions. In these

registers, the value of single bits can be checked by using the SBIS and SBIC instructions.

3. Some of the Status Flags are cleared by writing a logical one to them. Note that, unlike most other AVRs, the CBI and SBI

instructions will only operation the specified bit, and can therefore be used on registers containing such Status Flags. The

CBI and SBI instructions work with registers 0x00 to 0x1F only.

2586AS–AVR–02/05

ATtiny25/45/85

4. Instruction Set Summary

Mnemonics Operands Description Operation Flags #Clocks

ARITHMETIC AND LOGIC INSTRUCTIONS

ADD Rd, Rr Add two Registers Rd ← Rd + Rr Z,C,N,V,H 1

ADC Rd, Rr Add with Carry two Registers Rd ← Rd + Rr + C Z,C,N,V,H 1

ADIW Rdl,K Add Immediate to Word Rdh:Rdl ← Rdh:Rdl + K Z,C,N,V,S 2

SUB Rd, Rr Subtract two Registers Rd ← Rd - Rr Z,C,N,V,H 1

SUBI Rd, K Subtract Constant from Register Rd ← Rd - K Z,C,N,V,H 1

SBC Rd, Rr Subtract with Carry two Registers Rd ← Rd - Rr - C Z,C,N,V,H 1

SBCI Rd, K Subtract with Carry Constant from Reg. Rd ← Rd - K - C Z,C,N,V,H 1

SBIW Rdl,K Subtract Immediate from Word Rdh:Rdl ← Rdh:Rdl - K Z,C,N,V,S 2

AND Rd, Rr Logical AND Registers Rd ← Rd • Rr Z,N,V 1

ANDI Rd, K Logical AND Register and Constant Rd ← Rd • K Z,N,V 1

OR Rd, Rr Logical OR Registers Rd ← Rd v Rr Z,N,V 1

ORI Rd, K Logical OR Register and Constant Rd ← Rd v K Z,N,V 1

EOR Rd, Rr Exclusive OR Registers Rd ← Rd ⊕ Rr Z,N,V 1

COM Rd One’s Complement Rd ← 0xFF − Rd Z,C,N,V 1

NEG Rd Two’s Complement Rd ← 0x00 − Rd Z,C,N,V,H 1

SBR Rd,K Set Bit(s) in Register Rd ← Rd v K Z,N,V 1

CBR Rd,K Clear Bit(s) in Register Rd ← Rd • (0xFF - K) Z,N,V 1

INC Rd Increment Rd ← Rd + 1 Z,N,V 1

DEC Rd Decrement Rd ← Rd − 1 Z,N,V 1

TST Rd Test for Zero or Minus Rd ← Rd • Rd Z,N,V 1

CLR Rd Clear Register Rd ← Rd ⊕ Rd Z,N,V 1

SER Rd Set Register Rd ← 0xFF None 1

BRANCH INSTRUCTIONS

RJMP k Relative Jump PC ← PC + k + 1 None 2

IJMP Indirect Jump to (Z) PC ← Z None 2

RCALL k Relative Subroutine Call PC ← PC + k + 1 None 3

ICALL Indirect Call to (Z) PC ← ZNone3

RET Subroutine Return PC ← STACK None 4

RETI Interrupt Return PC ← STACK I 4

CPSE Rd,Rr Compare, Skip if Equal if (Rd = Rr) PC ← PC + 2 or 3 None 1/2/3

CP Rd,Rr Compare Rd − Rr Z, N,V,C,H 1

CPC Rd,Rr Compare with Carry Rd − Rr − C Z, N,V,C,H 1

CPI Rd,K Compare Register with Immediate Rd − K Z, N,V,C,H 1

SBRC Rr, b Skip if Bit in Register Cleared if (Rr(b)=0) PC ← PC + 2 or 3 None 1/2/3

SBRS Rr, b Skip if Bit in Register is Set if (Rr(b)=1) PC ← PC + 2 or 3 None 1/2/3

SBIC P, b Skip if Bit in I/O Register Cleared if (P(b)=0) PC ← PC + 2 or 3 None 1/2/3

SBIS P, b Skip if Bit in I/O Register is Set if (P(b)=1) PC ← PC + 2 or 3 None 1/2/3

BRBS s, k Branch if Status Flag Set if (SREG(s) = 1) then PC←PC+k + 1 None 1/2

BRBC s, k Branch if Status Flag Cleared if (SREG(s) = 0) then PC←PC+k + 1 None 1/2

BREQ k Branch if Equal if (Z = 1) then PC ← PC + k + 1 None 1/2

BRNE k Branch if Not Equal if (Z = 0) then PC ← PC + k + 1 None 1/2

BRCS k Branch if Carry Set if (C = 1) then PC ← PC + k + 1 None 1/2

BRCC k Branch if Carry Cleared if (C = 0) then PC ← PC + k + 1 None 1/2

BRSH k Branch if Same or Higher if (C = 0) then PC ← PC + k + 1 None 1/2

BRLO k Branch if Lower if (C = 1) then PC ← PC + k + 1 None 1/2

BRMI k Branch if Minus if (N = 1) then PC ← PC + k + 1 None 1/2

BRPL k Branch if Plus if (N = 0) then PC ← PC + k + 1 None 1/2

BRGE k Branch if Greater or Equal, Signed if (N ⊕ V= 0) then PC ← PC + k + 1 None 1/2

BRLT k Branch if Less Than Zero, Signed if (N ⊕ V= 1) then PC ← PC + k + 1 None 1/2

BRHS k Branch if Half Carry Flag Set if (H = 1) then PC ← PC + k + 1 None 1/2

BRHC k Branch if Half Carry Flag Cleared if (H = 0) then PC ← PC + k + 1 None 1/2

BRTS k Branch if T Flag Set if (T = 1) then PC ← PC + k + 1 None 1/2

BRTC k Branch if T Flag Cleared if (T = 0) then PC ← PC + k + 1 None 1/2

BRVS k Branch if Overflow Flag is Set if (V = 1) then PC ← PC + k + 1 None 1/2

BRVC k Branch if Overflow Flag is Cleared if (V = 0) then PC ← PC + k + 1 None 1/2

BRIE k Branch if Interrupt Enabled if ( I = 1) then PC ← PC + k + 1 None 1/2

BRID k Branch if Interrupt Disabled if ( I = 0) then PC ← PC + k + 1 None 1/2

BIT AND BIT-TEST INSTRUCTIONS

SBI P,b Set Bit in I/O Register I/O(P,b) ← 1None2

CBI P,b Clear Bit in I/O Register I/O(P,b) ← 0None2

LSL Rd Logical Shift Left Rd(n+1) ← Rd(n), Rd(0) ← 0 Z,C,N,V 1

LSR Rd Logical Shift Right Rd(n) ← Rd(n+1), Rd(7) ← 0 Z,C,N,V 1

ROL Rd Rotate Left Through Carry Rd(0)←C,Rd(n+1)← Rd(n),C←Rd(7) Z,C,N,V 1

2586AS–AVR–02/05

ATtiny25/45/85

ROR Rd Rotate Right Through Carry Rd(7)←C,Rd(n)← Rd(n+1),C←Rd(0) Z,C,N,V 1

ASR Rd Arithmetic Shift Right Rd(n) ← Rd(n+1), n=0..6 Z,C,N,V 1

SWAP Rd Swap Nibbles Rd(3..0)←Rd(7..4),Rd(7..4)←Rd(3..0) None 1

BSET s Flag Set SREG(s) ← 1 SREG(s) 1

BCLR s Flag Clear SREG(s) ← 0 SREG(s) 1

BST Rr, b Bit Store from Register to T T ← Rr(b) T 1

BLD Rd, b Bit load from T to Register Rd(b) ← TNone1

SEC Set Carry C ← 1C1

CLC Clear Carry C ← 0 C 1

SEN Set Negative Flag N ← 1N1

CLN Clear Negative Flag N ← 0 N 1

SEZ Set Zero Flag Z ← 1Z1

CLZ Clear Zero Flag Z ← 0 Z 1

SEI Global Interrupt Enable I ← 1I1

CLI Global Interrupt Disable I ← 0 I 1

SES Set Signed Test Flag S ← 1S1

CLS Clear Signed Test Flag S ← 0 S 1

SEV Set Twos Complement Overflow. V ← 1V1

CLV Clear Twos Complement Overflow V ← 0 V 1

SET Set T in SREG T ← 1T1

CLT Clear T in SREG T ← 0 T 1

SEH Set Half Carry Flag in SREG H ← 1H1

CLH Clear Half Carry Flag in SREG H ← 0 H 1

DATA TRANSFER INSTRUCTIONS

MOV Rd, Rr Move Between Registers Rd ← Rr None 1

MOVW Rd, Rr Copy Register Word Rd+1:Rd ← Rr+1:Rr None 1

LDI Rd, K Load Immediate Rd ← KNone1

LD Rd, X Load Indirect Rd ← (X) None 2

LD Rd, X+ Load Indirect and Post-Inc. Rd ← (X), X ← X + 1 None 2

LD Rd, - X Load Indirect and Pre-Dec. X ← X - 1, Rd ← (X) None 2

LD Rd, Y Load Indirect Rd ← (Y) None 2

LD Rd, Y+ Load Indirect and Post-Inc. Rd ← (Y), Y ← Y + 1 None 2

LD Rd, - Y Load Indirect and Pre-Dec. Y ← Y - 1, Rd ← (Y) None 2

LDD Rd,Y+q Load Indirect with Displacement Rd ← (Y + q) None 2

LD Rd, Z Load Indirect Rd ← (Z) None 2

LD Rd, Z+ Load Indirect and Post-Inc. Rd ← (Z), Z ← Z+1 None 2

LD Rd, -Z Load Indirect and Pre-Dec. Z ← Z - 1, Rd ← (Z) None 2

LDD Rd, Z+q Load Indirect with Displacement Rd ← (Z + q) None 2

LDS Rd, k Load Direct from SRAM Rd ← (k) None 2

ST X, Rr Store Indirect (X) ← Rr None 2

ST X+, Rr Store Indirect and Post-Inc. (X) ← Rr, X ← X + 1 None 2

ST - X, Rr Store Indirect and Pre-Dec. X ← X - 1, (X) ← Rr None 2

ST Y, Rr Store Indirect (Y) ← Rr None 2

ST Y+, Rr Store Indirect and Post-Inc. (Y) ← Rr, Y ← Y + 1 None 2

ST - Y, Rr Store Indirect and Pre-Dec. Y ← Y - 1, (Y) ← Rr None 2

STD Y+q,Rr Store Indirect with Displacement (Y + q) ← Rr None 2

ST Z, Rr Store Indirect (Z) ← Rr None 2

ST Z+, Rr Store Indirect and Post-Inc. (Z) ← Rr, Z ← Z + 1 None 2

ST -Z, Rr Store Indirect and Pre-Dec. Z ← Z - 1, (Z) ← Rr None 2

STD Z+q,Rr Store Indirect with Displacement (Z + q) ← Rr None 2

STS k, Rr Store Direct to SRAM (k) ← Rr None 2

LPM Load Program Memory R0 ← (Z) None 3

LPM Rd, Z Load Program Memory Rd ← (Z) None 3

LPM Rd, Z+ Load Program Memory and Post-Inc Rd ← (Z), Z ← Z+1 None 3

SPM Store Program Memory (z) ← R1:R0 None

IN Rd, P In Port Rd ← PNone1

OUT P, Rr Out Port P ← Rr None 1

PUSH Rr Push Register on Stack STACK ← Rr None 2

POP Rd Pop Register from Stack Rd ← STACK None 2

MCU CONTROL INSTRUCTIONS

NOP No Operation None 1

SLEEP Sleep (see specific descr. for Sleep function) None 1

WDR Watchdog Reset (see specific descr. for WDR/Timer) None 1

BREAK Break For On-chip Debug Only None N/A

Mnemonics Operands Description Operation Flags #Clocks

2586AS–AVR–02/05

ATtiny25/45/85

5. Ordering Information

Notes: 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information

and minimum quantities.

2. Pb-free packaging alternative, complies to the European Directive for Restriction of Hazardous Substances (RoHS direc-

tive). Also Halide free and fully Green.

3. For Speed vs. VCC,see Figure 23.4 on page 168

5.1 ATtiny25

Speed (MHz)(3) Power Supply Ordering Code Package(1) Operational Range

10 1.8 - 5.5V

ATtiny25V-10PI

ATtiny25V-10PU(2)

ATtiny25V-10SI

ATtiny25V-10SU(2)

8P3

8S2

Industrial

(-40°C to 85°C)

20 2.7 - 5.5V

ATtiny25-20PI

ATtiny25-20PU(2)

ATtiny25-20SI

ATtiny25-20SU(2)

8P3

8S2

Industrial

(-40°C to 85°C)

Package Type

8P3 8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP)

8S2 8-lead, 0.209" Wide, Plastic Gull-Wing Small Outline (EIAJ SOIC)

2586AS–AVR–02/05

ATtiny25/45/85

Notes: 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information

and minimum quantities.

2. Pb-free packaging alternative, complies to the European Directive for Restriction of Hazardous Substances (RoHS direc-

tive). Also Halide free and fully Green.

3. For Speed vs. VCC,see Figure 23.4 on page 168

5.2 ATtiny45

Speed (MHz)(3) Power Supply Ordering Code Package(1) Operational Range

10 1.8 - 5.5V

ATtiny45V-10PI

ATtiny45V-10PU(2)

ATtiny45V-10SI

ATtiny45V-10SU(2)

8P3

8S2

Industrial

(-40°C to 85°C)

20 2.7 - 5.5V

ATtiny45-20PI

ATtiny45-20PU(2)

ATtiny45-20SI

ATtiny45-20SU(2)

8P3

8S2

Industrial

(-40°C to 85°C)

Package Type

8P3 8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP)

8S2 8-lead, 0.209" Wide, Plastic Gull-Wing Small Outline (EIAJ SOIC)

2586AS–AVR–02/05

ATtiny25/45/85

Notes: 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information

and minimum quantities.

2. Pb-free packaging alternative, complies to the European Directive for Restriction of Hazardous Substances (RoHS direc-

tive). Also Halide free and fully Green.

3. For Speed vs. VCC,see Figure 23.4 on page 168

5.3 ATtiny85

Speed (MHz)(3) Power Supply Ordering Code Package(1) Operational Range

10 1.8 - 5.5V

ATtiny85V-10PI

ATtiny85V-10PU(2)

ATtiny85V-10SI

ATtiny85V-10SU(2)

8P3

8S2

Industrial

(-40°C to 85°C)

20 2.7 - 5.5V

ATtiny85-20PI

ATtiny85-20PU(2)

ATtiny85-20SI

ATtiny85-20SU(2)

8P3

8S2

Industrial

(-40°C to 85°C)

Package Type

8P3 8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP)

8S2 8-lead, 0.209" Wide, Plastic Gull-Wing Small Outline (EIAJ SOIC)

2586AS–AVR–02/05

ATtiny25/45/85

6. Packaging Information

6.1 8P3

2325 Orchard Parkway

San Jose, CA 95131

TITLE DRAWING NO.

REV.

8P3, 8-lead, 0.300" Wide Body, Plastic Dual

In-line Package (PDIP)

01/09/02

8P3 B

A2 A

4 PLCS

Top View

Side View

End View

COMMON DIMENSIONS

(Unit of Measure = inches)

SYMBOL MIN NOM MAX NOTE

Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA for additional information.

2. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3.

3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch.

4. E and eA measured with the leads constrained to be perpendicular to datum.

5. Pointed or rounded lead tips are preferred to ease insertion.

6. b2 and b3 maximum dimensions do not include Dambar protrusions. Dambar protrusions shall not exceed 0.010 (0.25 mm).

A 0.210 2

A2 0.115 0.130 0.195

b 0.014 0.018 0.022 5

b2 0.045 0.060 0.070 6

b3 0.030 0.039 0.045 6

c 0.008 0.010 0.014

D 0.355 0.365 0.400 3

D1 0.005 3

E 0.300 0.310 0.325 4

E1 0.240 0.250 0.280 3

e 0.100 BSC

eA 0.300 BSC 4

L 0.115 0.130 0.150 2

2586AS–AVR–02/05

ATtiny25/45/85

6.2 8S2

2325 Orchard Parkway

San Jose, CA 95131

TITLE DRAWING NO.

REV.

8S2, 8-lead, 0.209" Body, Plastic Small

Outline Package (EIAJ)

10/7/03

8S2

COMMON DIMENSIONS

(Unit of Measure = mm)

SYMBOL MIN NOM MAX NOTE

Notes: 1. This drawing is for general information only; refer to EIAJ Drawing EDR-7320 for additional information.

2. Mismatch of the upper and lower dies and resin burrs are not included.

3. It is recommended that upper and lower cavities be equal. If they are different, the larger dimension shall be regarded.

4. Determines the true geometric position.

5. Values b and C apply to pb/Sn solder plated terminal. The standard thickness of the solder layer shall be 0.010 +0.010/−0.005 mm.

A 1.70 2.16

A1 0.05 0.25

b 0.35 0.48 5

C 0.15 0.35 5

D 5.13 5.35

E1 5.18 5.40 2, 3

E 7.70 8.26

L 0.51 0.85

∅

0˚ 8˚

e 1.27 BSC 4

End View

Side View

∅

Top View

2586AS–AVR–02/05

ATtiny25/45/85

7. Errata

The revision letter in this section refers to the revision of the ATtiny25/45/85 device.

7.1 ATtiny25/45/85 Rev. A

•Too high power down power consumption

•DebugWIRE looses communication when single stepping into interrupts

•PLL not locking

1. Too high power down power consumption

Three situations will lead to a too high power down power consumption. These are:

– An external clock is selected by fuses, but the IO PORT is still enabled as an output.

– The EEPROM is read before entering power down.

– VCC is 4.5 volts or higher.

Problem fix / Workaround

– When using external clock, avoid setting the clock pin as Output.

– Do not read the EEPROM if power down power consumption is important.

– Use VCC lower than 4.5 Volts.

2. DebugWIRE looses communication when single stepping into interrupts

When receiving an interrupt during single stepping, debugwire will loose

communication.

Problem fix / Workaround

– When singlestepping disable interrupts.

– When debugging interrupts, use breakpoints within the interrupt routine, and run into

the interrupt.

3. PLL not locking

When running at frequencies below 6.0 MHz, the PLL will not lock

Problem fix / Workaround

– When using the PLL, run at 6.0 MHz or higher.

2586AS–AVR–02/05

ATtiny25/45/85

8. Datasheet Revision History

8.1 Rev. 2586A-02/05

1. Initial revision.

Printed on recycled paper.

2586AS–AVR–02/05

Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any

intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI-

TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY

WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDEN-

TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT

OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no

representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications

and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Atmel’s products are not

intended, authorized, or warranted for use as components in applications intended to support or sustain life.

Atmel Corporation Atmel Operations

2325 Orchard Parkway

San Jose, CA 95131, USA

Tel: 1(408) 441-0311

Fax: 1(408) 487-2600

Regional Headquarters

Europe

Atmel Sarl

Route des Arsenaux 41

Case Postale 80

CH-1705 Fribourg

Switzerland

Tel: (41) 26-426-5555

Fax: (41) 26-426-5500

Asia

Room 1219

Chinachem Golden Plaza

77 Mody Road Tsimshatsui

East Kowloon

Hong Kong

Tel: (852) 2721-9778

Fax: (852) 2722-1369

Japan

9F, Tonetsu Shinkawa Bldg.

1-24-8 Shinkawa

Chuo-ku, Tokyo 104-0033

Japan

Tel: (81) 3-3523-3551

Fax: (81) 3-3523-7581

Memory

2325 Orchard Parkway

San Jose, CA 95131, USA

Tel: 1(408) 441-0311

Fax: 1(408) 436-4314

Microcontrollers

2325 Orchard Parkway

San Jose, CA 95131, USA

Tel: 1(408) 441-0311

Fax: 1(408) 436-4314

La Chantrerie

BP 70602

44306 Nantes Cedex 3, France

Tel: (33) 2-40-18-18-18

Fax: (33) 2-40-18-19-60

ASIC/ASSP/Smart Cards

Zone Industrielle

13106 Rousset Cedex, France

Tel: (33) 4-42-53-60-00

Fax: (33) 4-42-53-60-01

1150 East Cheyenne Mtn. Blvd.

Colorado Springs, CO 80906, USA

Tel: 1(719) 576-3300

Fax: 1(719) 540-1759

Scottish Enterprise Technology Park

Maxwell Building

East Kilbride G75 0QR, Scotland

Tel: (44) 1355-803-000

Fax: (44) 1355-242-743

RF/Automotive

Theresienstrasse 2

Postfach 3535

74025 Heilbronn, Germany

Tel: (49) 71-31-67-0

Fax: (49) 71-31-67-2340

1150 East Cheyenne Mtn. Blvd.

Colorado Springs, CO 80906, USA

Tel: 1(719) 576-3300

Fax: 1(719) 540-1759

Biometrics/Imaging/Hi-Rel MPU/

High Speed Converters/RF Datacom

Avenue de Rochepleine

BP 123

38521 Saint-Egreve Cedex, France

Tel: (33) 4-76-58-30-00

Fax: (33) 4-76-58-34-80

Literature Requests

www.atmel.com/literature

and Everywhere You AreSM are the trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of

others.