SLVS024E – FEBRUAR Y 1983 – REVISED NOVEMBER 1999
1
www.ti.com
DComplete PWM Power Control Circuitry
DCompletely Synchronized Operation
DInternal Undervoltage Lockout Protection
DWide Supply Voltage Range
DInternal Short-Circuit Protection
DOscillator Frequency ...500 kHz Max
DVariable Dead Time Provides Control Over
Total Range
DInternal Regulator Provides a Stable 2.5-V
Reference Supply
DAvailable in Q-Temp Automotive
HighRel Automotive Applications
Configuration Control / Print Support
Qualification to Automotive Standards
description
The TL1451A incorporates on a single monolithic
chip all the functions required in the construction
of two pulse-width-modulation (PWM) control
circuits. Designed primarily for power-supply
control, the TL1451A contains an on-chip 2.5-V
regulator, two error amplifiers, an adjustable
oscillator, two dead-time comparators, undervol-
tage lockout circuitry, and dual common-emitter
output transistor circuits.
The uncommitted output transistors provide
common-emitter output capability for each
controller. The internal amplifiers exhibit a common-mode voltage range from 1.04 V to 1.45 V. The dead-time
control (DTC) comparator has no offset unless externally altered and can provide 0% to 100% dead time. The
on-chip oscillator can be operated by terminating RT and CT. During low VCC conditions, the undervoltage
lockout control circuit feature locks the outputs off until the internal circuitry is operational.
The TL1451AC is characterized for operation from –20°C to 85°C. The TL1451AQ is characterized for operation
from –40°C to 125°C. The TL1451AM is characterized for operation from –55°C to 125°C.
AVAILABLE OPTIONS
PACKAGED DEVICES
TASMALL
OUTLINE
(D)
SMALL
OUTLINE
(DB)†
PLASTIC DIP
(N)
SMALL
OUTLINE
(NS)
TSSOP
(PW)†
CHIP
CARRIER
(FK)
CERAMIC
DIP
(J)
–20°C to 85°C TL1451ACD TL1451ACDB TL1451ACN TL1451ACNS TL1451ACPW — —
–40°C to 125°C TL1451AQD — — — — — —
–55°C to 125°C — — — — — TL1451AMFK TL1451AMJ
†The DB and PW packages are only available left-end taped and reeled (add LE suffix, i.e., TL1451ACPWLE).
Copyright 1999, Texas Instruments Incorporated
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
CT
RT
ERROR 1IN+
AMPLIFIER 1 1IN–
1FEEDBACK
1DTC
1OUT
GND
REF
SCP
2IN+ ERROR
2IN– AMPLIFIER 2
2FEEDBACK
2DTC
2OUT
VCC
D, DB, N, NS, PW, OR J PACKAGE
(TOP VIEW)
1920132
17
18
16
15
14
1312119 10
5
4
6
7
8
2IN+
2IN–
NC
2FEEDBACK
2DTC
1IN+
1IN–
NC
1FEEDBACK
IDTC
RT
CT
NC
REF
SCP
GND
NC
V
2
OUT
1OUT
FK PACKAGE
(TOP VIEW)
CC
SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999
2www.ti.com
functional block diagram
+
–
+
–
Oscillator
Reference
Voltage
1/2 Vref
R
S
170 kΩUVLO
R
92 1
VCC RT CT
10
16
7
8
REF
GND
PWM
COMP
PWM
COMP
12 kΩ
11
14
13
12
5
15
3
4
6
2 DTC
IN+
IN–
2 FEEDBACK
1 FEEDBACK
SCP
IN+
IN–
1 DTC
ERROR
AMPLIFIER 2
ERROR
AMPLIFIER 1 1 OUTPUT
2 OUTPUT
COMPONENT COUNT
Resistors 65
Capacitors 8
Transistors 105
JFETs 18
SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999
3
www.ti.com
absolute maximum ratings over operating free-air temperature range†
Supply voltage, VCC 51 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Amplifier input voltage, VI20 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Collector output voltage, VO51 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Collector output current, IO21 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous power total dissipation See Dissipation Rating Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating free-air temperature range, TA C suffix –20°C to 85°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Q suffix –40°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
M suffix –55°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, Tstg –65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds 260°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
†Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only , an d
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
DISSIPATION RATING TABLE
PACKAGE TA ≤ 25°C
POWER RATING DERATING FACTOR
ABOVE TA = 25°CTA = 70°C
POWER RATING TA = 85°C
POWER RATING TA = 125°C
POWER RATING
D1088 mW 8.7 mW/°C696 mW 566 mW 218 mW
DB 775 mW 6.2 mW/°C 496 mW 403 mW —
N1000 mW 8.0 mW/°C 640 mW 520 mW —
NS 500 mW 4.0 mW/°C 320 mW 260 mW —
PW 838 mW 6.7 mW/°C 536 mW 436 mW 168 mW
FK 1375 mW 11.0 mW/°C 880 mW 715 mW 275 mW
J1375 mW 11.0 mW/°C880 mW 715 mW 275 mW
recommended operating conditions
MIN MAX UNIT
Supply voltage, VCC 3.6 50 V
Amplifier input voltage, VI1.05 1.45 V
Collector output voltage, VO50 V
Collector output current, IO20 mA
Current into feedback terminal 45 µA
Feedback resistor, RF100 kΩ
Timing capacitor, CT150 15000 pF
Timing resistor, RT5.1 100 kΩ
Oscillator frequency 1 500 kHz
C suffix –20 85
Operating free-air temperature, TAQ suffix –40 125 °C
g,
A
M suffix –55 125
SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999
4www.ti.com
electrical characteristics over recommended operating free-air temperature range, VCC = 6 V,
f = 200 kHz (unless otherwise noted)
reference section
PARAMETER
TEST CONDITIONS
TL1451AC
UNIT
PARAMETER TEST CONDITIONS MIN TYP†MAX UNIT
Output voltage (pin 16) IO = 1 mA 2.4 2.5 2.6 V
O tp t oltage change ith temperat re
TA = –20°C to 25°C–0.1% ±1%
Output voltage change with temperature TA = 25°C to 85°C–0.2% ±1%
Input voltage regulation VCC = 3.6 V to 40 V 2 12.5 mV
Output voltage regulation IO = 0.1 mA to 1 mA 1 7.5 mV
Short-circuit output current VO = 0 3 10 30 mA
†All typical values are at TA = 25°C.
undervoltage lockout section
PARAMETER
TEST CONDITIONS
TL1451AC
UNIT
PARAMETER TEST CONDITIONS MIN TYP†MAX UNIT
Upper threshold voltage (VCC) 2.72 V
Lower threshold voltage (VCC)
IO( f) 01mA T
A25°C
2.6 V
Hysteresis (VCC)IO(ref) = 0.1 mA, TA = 25°C80 120 mV
Reset threshold voltage (VCC) 1.5 1.9 V
†All typical values are at TA = 25°C.
short-circuit protection control section
PARAMETER
TEST CONDITIONS
TL1451AC
UNIT
PARAMETER TEST CONDITIONS MIN TYP†MAX UNIT
Input threshold voltage (SCP) TA = 25°C 0.65 0.7 0.75 V
Standby voltage (SCP) No pullup 140 185 230 mV
Latched input voltage (SCP) No pullup 60 120 mV
Input (source) current VI = 0.7 V, TA = 25°C–10 –15 –20 µA
Comparator threshold voltage (FEEDBACK) 1.18 V
†All typical values are at TA = 25°C.
oscillator section
PARAMETER
TEST CONDITIONS
TL1451C
UNIT
PARAMETER TEST CONDITIONS MIN TYP†MAX UNIT
Frequency CT = 330 pF, RT = 10 kΩ200 kHz
Standard deviation of frequency CT = 330 pF, RT = 10 kΩ10%
Frequency change with voltage VCC = 3.6 V to 40 V 1%
Frequency change with tem
p
erature
TA = –20°C to 25°C–0.4% ±2%
Frequency change with temperature TA = 25°C to 85°C–0.2% ±2%
†All typical values are at TA = 25°C.
SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999
5
www.ti.com
dead-time control section
PARAMETER
TEST CONDITIONS
TL1451AC
UNIT
PARAMETER TEST CONDITIONS MIN TYP†MAX UNIT
Input bias current (DTC) 1µA
Latch mode (source) current (DTC) TA = 25°C–80 –145 µA
Latched input voltage (DTC) IO = 40 µA 2.3 V
In
p
ut threshold voltage at f 10 kHz (DTC)
Zero duty cycle 2.05 2.25
V
Input threshold voltage at f = 10 kHz (DTC) Maximum duty cycle 1.2 1.45 V
†All typical values are at TA = 25°C.
error-amplifier section
PARAMETER
TEST CONDITIONS
TL1451AC
UNIT
PARAMETER TEST CONDITIONS MIN TYP†MAX UNIT
Input offset voltage VO (FEEDBACK) = 1.25 V ±6 mV
Input offset current VO (FEEDBACK) = 1.25 V ±100 nA
Input bias current VO (FEEDBACK) = 1.25 V 160 500 nA
1.05
Common-mode input volta
g
e ran
g
e V
CC
= 3.6 V to 40 V
1
.
05
to V
Common mode
in ut
voltage
range
VCC
=
3
.
6
V
to
40
V
to
1.45
V
Open-loop voltage amplification RF = 200 kΩ70 80 dB
Unity-gain bandwidth 1.5 MHz
Common-mode rejection ratio 60 80 dB
Positive output voltage swing Vref–0.1 V
Negative output voltage swing 1 V
Output (sink) current (FEEDBACK) VID = –0.1 V, VO = 1.25 V 0.5 1.6 mA
Output (source) current (FEEDBACK) VID = 0.1 V, VO = 1.25 V –45 –70 µA
†All typical values are at TA = 25°C.
output section
PARAMETER
TEST CONDITIONS
TL1451AC
UNIT
PARAMETER TEST CONDITIONS MIN TYP†MAX UNIT
Collector off-state current VO = 50 V 10 µA
Output saturation voltage IO = 10 mA 1.2 2 V
Short-circuit output current VO = 6 V 90 mA
†All typical values are at TA = 25°C.
pwm comparator section
PARAMETER
TEST CONDITIONS
TL1451AC
UNIT
PARAMETER TEST CONDITIONS MIN TYP†MAX UNIT
In
p
ut threshold voltage at f 10 kHz (FEEDBACK)
Zero duty cycle 2.05 2.25
V
Input threshold voltage at f = 10 kHz (FEEDBACK) Maximum duty cycle 1.2 1.45 V
†All typical values are at TA = 25°C.
total device
PARAMETER
TEST CONDITIONS
TL1451AC
UNIT
PARAMETER TEST CONDITIONS MIN TYP†MAX UNIT
Standby supply current Off-state 1.3 1.8 mA
Average supply current RT = 10 kΩ1.7 2.4 mA
†All typical values are at TA = 25°C.
SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999
6www.ti.com
electrical characteristics over recommended operating free-air temperature range, VCC = 6 V,
f = 200 kHz (unless otherwise noted)
reference section
PARAMETER
TEST CONDITIONS
TL1451AQ, TL1451AM
UNIT
PARAMETER TEST CONDITIONS MIN TYP†MAX UNIT
O tp t oltage (pin 16)
I1mA
TA = 25°C 2.40 2.50 2.60
V
Output voltage (pin 16) IO = 1 mA TA = MIN and 125°C 2.35 2.46 2.65 V
Output voltage change with temperature –0.63% *±4%
TA = 25°C 2.0 12.5
Input voltage regulation VCC = 3.6 V to 40 V TA = 125°C 0.7 15 mV
In ut
voltage
regulation
VCC
3.6
V
to
40
V
TA = MIN 0.3 30
mV
TA = 25°C 1.0 7.5
Output voltage regulation IO = 0.1 mA to 1 mA TA = 125°C 0.3 14 mV
Out ut
voltage
regulation
IO
0.1
mA
to
1
mA
TA = MIN 0.3 20
mV
Short-circuit output current VO = 0 3 10 30 mA
*These parameters are not production tested.
†All typical values are at TA = 25°C unless otherwise indicated.
undervoltage lockout section
PARAMETER
TEST CONDITIONS
TL1451AQ, TL1451AM
UNIT
PARAMETER TEST CONDITIONS MIN TYP†MAX UNIT
TA = 25°C 2.72
Upper threshold voltage (VCC)TA = 125°C 1.70 V
Uer
threshold
voltage
(VCC)
TA = MIN 3.15
V
TA = 25°C 2.60
Lower threshold voltage (VCC)TA = 125°C 1.65 V
Lower
threshold
voltage
(VCC)
TA = MIN 3.09
V
TA = 25°C 80 120
Hysteresis (VCC)TA = 125°C 10 50 mV
Hysteresis
(VCC)
TA = MIN 10 60
mV
TA = 25°C 1.50
Reset threshold voltage (VCC)TA = 125°C 0.95 V
g(CC)
TA = MIN 1.50
†All typical values are at TA = 25°C unless otherwise indicated.
SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999
7
www.ti.com
short-circuit protection control section
PARAMETER
TEST CONDITIONS
TL1451AQ, TL1451AM
UNIT
PARAMETER TEST CONDITIONS MIN TYP†MAX UNIT
TA = 25°C 650 700 750
Input threshold voltage (SCP) TA = 125°C 400 478 550 mV
In ut
threshold
voltage
(SCP)
TA = MIN 800 880 950
mV
Standby voltage (SCP) 140 185 230 mV
TA = 25°C 60 120
Latched input voltage (SCP) TA = 125°C 70 120 mV
Latched
in ut
voltage
(SCP)
TA = MIN 60 120
mV
Equivalent timing resistance 170 kΩ
Comparator threshold voltage (FEEDBACK) 1.18 V
†All typical values are at TA = 25°C unless otherwise indicated.
oscillator section
PARAMETER
TEST CONDITIONS
TL1451AQ, TL1451AM
UNIT
PARAMETER TEST CONDITIONS MIN TYP†MAX UNIT
C 330 F
TA = 25°C 200
Frequency CT = 330 pF,
RT=10kΩ
TA = 125°C 195 kHz
Frequency
R
T =
10
kΩ
TA = MIN 193
kHz
Standard deviation of frequency CT = 330 pF, RT = 10 kΩ2%
TA = 25°C 1%
Frequency change with voltage VCC = 3.6 V to 40 V TA = 125°C 1%
Frequency
change
with
voltage
VCC
3.6
V
to
40
V
TA = MIN 3%
Frequency change with temperature 1.37% *±10%
*These parameters are not production tested.
†All typical values are at TA = 25°C unless otherwise indicated.
dead-time control section
PARAMETER
TEST CONDITIONS
TL1451AQ, TL1451AM
UNIT
PARAMETER TEST CONDITIONS MIN TYP†MAX UNIT
Inp t bias c rrent (DTC)
TA = 25°C 1
A
Input bias current (DTC) TA = MIN and 125°C 3 µA
Latch mode (source) current (DTC) –80 –145 µA
TA = 25°C 2.30
Latched input voltage (DTC) TA = 125°C 2.22 2.32 V
Latched
in ut
voltage
(DTC)
TA = MIN 2.28 2.40
V
In
p
ut threshold voltage at f 10 kHz (DTC)
Zero duty cycle 2.05 *2.25
V
Input threshold voltage at f = 10 kHz (DTC) Maximum duty cycle *1.20 1.45 V
*These parameters are not production tested.
†All typical values are at TA = 25°C unless otherwise indicated.
SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999
8www.ti.com
error-amplifier section
PARAMETER
TEST CONDITIONS
TL1451AQ, TL1451AM
UNIT
PARAMETER TEST CONDITIONS MIN TYP†MAX UNIT
TA = 25°C±6
Input offset voltage VO (FEEDBACK) = 1.25 V TA = 125°C±10 mV
In ut
offset
voltage
VO
(FEEDBACK)
1.25
V
TA = MIN ±12
mV
TA = 25°C±100
Input offset current VO (FEEDBACK) = 1.25 V TA = 125°C±100 nA
In ut
offset
current
VO
(FEEDBACK)
1.25
V
TA = MIN ±200
nA
TA = 25°C 160 500
Input bias current VO (FEEDBACK) = 1.25 V TA = 125°C 100 500 nA
In ut
bias
current
VO
(FEEDBACK)
1.25
V
TA = MIN 142 700
nA
1.05
Common-mode input volta
g
e ran
g
e V
CC
= 3.6 V to 40 V
1
.
05
to V
Common mode
in ut
voltage
range
VCC
=
3
.
6
V
to
40
V
to
1.45
V
TA = 25°C 70 80
Open-loop voltage amplification RF = 200 kΩTA = 125°C 70 80 dB
O en loo
voltage
am lification
RF
200
kΩ
TA = MIN 64 80
dB
Unity-gain bandwidth 1.5 MHz
Common-mode rejection ratio 60 80 dB
Positive output voltage swing 2 V
Negative output voltage swing 1 V
TA = 25°C 0.5 1.6
Output (sink) current (FEEDBACK) VID = –0.1 V, VO = 1.25 V TA = 125°C 0.4 1.8 mA
Out ut
(sink)
current
(FEEDBACK)
VID
0.1
V,
VO
1.25
V
TA = MIN 0.3 1.7
mA
TA = 25°C–45 –70
Output (source) current (FEEDBACK) VID = 0.1 V, VO = 1.25 V TA = 125°C–25 –50 µA
() ( )
ID ,O
TA = MIN –15 –70
µ
†All typical values are at TA = 25°C unless otherwise indicated.
output section
PARAMETER
TEST CONDITIONS
TL1451AQ, TL1451AM
UNIT
PARAMETER TEST CONDITIONS MIN TYP†MAX UNIT
Collector off-state current VO = 50 V 10 µA
TA = 25°C 1.20 2.0
Output saturation voltage TA = 125°C 1.60 2.4 V
Out ut
saturation
voltage
TA = MIN 1.36 2.2
V
Short-circuit output current VO = 6 V 90 mA
†All typical values are at TA = 25°C unless otherwise indicated.
pwm comparator section
PARAMETER
TEST CONDITIONS
TL1451AQ, TL1451AM
UNIT
PARAMETER TEST CONDITIONS MIN TYP†MAX UNIT
In
p
ut threshold voltage at f 10 kHz (FEEDBACK)
Zero duty cycle 2.05 *2.25
V
Input threshold voltage at f = 10 kHz (FEEDBACK) Maximum duty cycle *1.20 1.45 V
*These parameters are not production tested.
†All typical values are at TA = 25°C unless otherwise indicated.
SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999
9
www.ti.com
total device
PARAMETER
TEST CONDITIONS
TL1451AQ, TL1451AM
UNIT
PARAMETER TEST CONDITIONS MIN TYP†MAX UNIT
Standby supply current Off-state 1.3 1.8 mA
Average supply current RT = 10 kΩ1.7 2.4 mA
†All typical values are at TA = 25°C unless otherwise indicated.
PARAMETER MEASUREMENT INFORMATION
87654321
910111213141516
S1
CPE 0.47 µF
Test
Input VCC = 5 V RL
4.7 kΩ
4.7 kΩ
RL
OUT1
OUT2
CT
330 pF RT
10 kΩ
Test
Input
TL1451A
Figure 1. Test Circuit
Dead Time 100%
tpe†
2.0 V
1.6 V
1.4 V
1.25 V
H
L
H
L
0.6 V
0 V
H
L
3.6 V
0 V
Oscillator Triangle Waveform
Error Amplifier Output
Dead-Time Input Voltage
Short-Circuit Protection
Comparator Input Voltage
PWM Comparator Output Voltage
Output Transistor Collector
Waveform
Protection Enable
Terminal Waveform
Short-Circuit Protection
Comparator Output
Power Supply Voltage
†Protection Enable Time, tpe = (0.051 x 106 x Cpe) in seconds
2.8 V TYP
Figure 2. TL1451A Timing Diagram
SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999
10 www.ti.com
TYPICAL CHARACTERISTICS
100 k
10 k
1 k
1 M
1 k 4 k 10 k 40 k 100 k 400 k 1 M
TRIANGLE OSCILLATOR FREQUENCY
vs
TIMING RESISTANCE
CT = 150 pF
CT = 1500 pF
CT = 15000 pF
VCC = 5 V
TA = 25°C
RT – Timing Resistance – Ω
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
0
–1
–2
–3
–25 0 25 50
afosc – Oscillator Frequency Variation – %
1
2
OSCILLATOR FREQUENCY VARIATION
vs
FREE-AIR TEMPERATURE
3
75 100
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
VCC = 3.6 V
RT = 10 kΩ
CT = 330 pF
fosc = 200 kHz
TA – Free-Air Temperature – °C
osc
f
∆
fosc – Triangle Oscillator Frequency – Hz
osc
f
Figure 3 Figure 4
2.2
2
1.6
1.4
0.8
2.6
1.8
Triangle Waveform Swing Voltage – V
2.4
TRIANGLE WAVEFORM SWING VOLTAGE
vs
TIMING CAPACITANCE
1.2
1
VCC = 5 V
RT = 5.1 kΩ
TA = 25°C
CT – Timing Capacitance – pF
101102103104105
Triangle Waveform Period – uS
TRIANGLE WAVEFORM PERIOD
vs
TIMING CAPACITANCE
VCC = 5 V
RT = 5.1 kΩ
TA = 25°C
sµ
102
101
100
10–1
101102103104105
CT – Timing Capacitance – pF
Figure 5 Figure 6
SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999
11
www.ti.com
TYPICAL CHARACTERISTICS
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
0
–10
– 20
– 30
– 25 0 25 50
10
20
REFERENCE OUTPUT VOLTAGE VARIATION
vs
FREE-AIR TEMPERATURE
30
75 100
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
VCC = 3.6 V
II(ref) = 1 mA
TA – Free-Air Temperature – °C
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎÎ
0
–10
– 20
– 30
– 25 0 25 50
10
20
REFERENCE OUTPUT VOLTAGE VARIATION
vs
FREE-AIR TEMPERATURE
30
75 100
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
VCC = 40 V
II(ref) = 1 mA
TA – Free-Air Temperature – °C
avref – Reference Output Voltage Variation – mV
ÁÁ
ÁÁ
ÁÁ
ÁÁ
VO(ref)
∆
avref – Reference Output Voltage Variation – mV
ÁÁ
ÁÁ
ÁÁ
ÁÁ
VO(ref)
∆
Figure 7 Figure 8
1.5
1
0.5
00 5 10 15 20 25
2
2.5
REFERENCE OUTPUT VOLTAGE
vs
SUPPLY VOLTAGE
3
30 35 40
TA = 25°C
VCC – Supply Voltage – V
0.8
0.7
0.6
– 25 0 25 50
Dropout Voltage Variation – V
0.9
1
DROPOUT VOLTAGE VARIATION
vs
FREE-TEMPERATURE
1.1
75 100
TA – Free-Air Temperature – °C
II(ref) = 1 mA
Vref – Reference Output Voltage – V
ÁÁ
ÁÁ
ÁÁ
VO(ref)
Figure 9 Figure 10
SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999
12 www.ti.com
TYPICAL CHARACTERISTICS
3
2
1
00123
VCE – Output Collector Voltage – V
4
5
UNDERVOLTAGE LOCKOUT
HYSTERESIS CHARACTERISTICS
6
45
TA = 25°CTA = –20°C
IO = 10 mA
7,10
8
RL
5 V
I = IO
VDE
TA = 85°C
VCC – Supply Voltage – V
ÁÁ
ÁÁ
ÁÁ
VCE
2
–25 0 25 50
Undervoltage Lockout Threshold Voltage – V
2.5
3
UNDERVOLTAGE LOCKOUT CHARACTERISTIC
3.5
75 100
Threshold Voltage –VTH
(Left Scale)
Threshold Voltage –VTL
(Left Scale)
Hysteresis Voltage
(Right Scale)
300
200
100
0
Undervoltage Lockout Hystersis Voltage – mV
TA – Free-Air Temperature – °C
3.25
2.75
2.25 50
150
250
Figure 11 Figure 12
1.20
1.15
1.10
– 25 0 25
Comparator Threshold Voltage – V
1.25
1.30
SHORT-CIRCUIT PROTECTION CHARACTERISTICS
50 75 100
Short-Circuit Protection
Latch Reset Supply Voltage
(Right Scale)
Short-Circuit Protection
Comparator Threshold Voltage
(Left Scale)
3
2.5
2
1.5
1
RS – Latch Reset Supply Voltage – V
TA – Free-Air Temperature – °C
Figure 13
SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999
13
www.ti.com
TYPICAL CHARACTERISTICS
9
6
3
00 50 100 150
tpe – Protection Enable Time – s
12
15
PROTECTION ENABLE TIME
vs
PROTECTION ENABLE CAPACITANCE
18
200 250
tpe
CPE – Protection Enable Capacitance – µF
+
–
Protection
Latch
SR
CPE U.V.L.O.
ERROR AMP 1
ERROR AMP 2
1.25 V
Short-circuit
Protection
Comparator 12 kΩ
15 16
SCP Vref
170 kΩVref Vref
Figure 14
SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999
14 www.ti.com
TYPICAL CHARACTERISTICS
1.75
1.5
1
0.75
0
2.25
1.25
1 k 10 k 100 k 1 M 10 M
Error Amp Maximum Output Voltage Swing – V
2
f – Frequency – Hz
ERROR AMP MAXIMUM OUTPUT VOLTAGE SWING
vs
FREQUENCY
0.5
0.25
VCC = 5 V
TA = 25°C
70
60
40
30
0
90
50
100 1 k 10 k 100 k 1 M 2 M
Open-Loop Voltage Amplification – dB
80
f – Frequency – Hz
OPEN-LOOP VOLTAGE AMPLIFICATION
vs
FREQUENCY
20
10
VCC = 5 V
TA = 25°C
Figure 15 Figure 16
–5
–20
1 k 10 k 100 k
G – Gain – dB
f – Frequency – Hz
GAIN (AMPLIFIER IN
UNITY-GAIN CONFIGURATION)
vs
FREQUENCY
10
1 M 10 M
5
0
–10
–15
VCC = 5 V
TA = 25°C
Figure 17
SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999
15
www.ti.com
TYPICAL CHARACTERISTICS
47 pF
470 pF
4700 pF
CX:
Phase Shift
(Right Scale)
Closed-Loop Gain
(Left Scale)
VCC = 5 V
Rref = 150 Ω
Cref = 470 pF
TA = 25°C
50
30
20
0
70
40
100 1 k 10 k 100 k 1 M
Closed-Loop Gain – dB
60
f – Frequency – Hz
CLOSED-LOOP GAIN AND PHASE SHIFT
vs
FREQUENCY
10
0°
–10°
–20°
–30°
–40°
–50°
–60°
–70°
–80°
–90°
Phase Shift
CxRref
Cref
Vref
39 kΩ
39 kΩ
+
–
Test Circuit
Figure 18
SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999
16 www.ti.com
TYPICAL CHARACTERISTICS
47 pF
470 pF
4700 pF
CX:
Phase Shift
(Right Scale)
Closed-Loop Gain
(Left Scale)
VCC = 5 V
Rref = 15 Ω
Cref = 470 pF
TA = 25°C
50
30
20
0
70
40
100 1 k 10 k 100 k 1 M
Closed-Loop Gain – dB
60
f – Frequency – Hz
CLOSED-LOOP GAIN AND PHASE SHIFT
vs
FREQUENCY
10
0°
–10°
–20°
–30°
–40°
–50°
–60°
–70°
–80°
–90°
Phase Shift
CxRref
Cref
Vref
39 kΩ
39 kΩ
+
–
Test Circuit
Figure 19
SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999
17
www.ti.com
TYPICAL CHARACTERISTICS
47 pF
470 pF
4700 pF
CX:
Phase Shift
(Right Scale)
Closed-Loop Gain
(Left Scale)
VCC = 5 V
Rref = 15 Ω
Cref = 470 pF
TA = 25°C
50
30
20
0
70
40
100 1 k 10 k 100 k 1 M
Closed-Loop Gain – dB
60
f – Frequency – Hz
CLOSED-LOOP GAIN AND PHASE SHIFT
vs
FREQUENCY
10
0°
–10°
–20°
–30°
–40°
–50°
–60°
–70°
–80°
–90°
Phase Shift
CxRref
Cref
Vref
39 kΩ
39 kΩ
+
–
Test Circuit
Figure 20
SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999
18 www.ti.com
TYPICAL CHARACTERISTICS
Phase Shift
(Right Scale)
Closed-Loop Gain
(Left Scale)
VCC = 5 V
Cref = 470 pF
TA = 25°C
50
30
20
0
70
40
100 1 k 10 k 100 k 1 M
Closed-Loop Gain – dB
60
f – Frequency – Hz
CLOSED-LOOP GAIN AND PHASE SHIFT
vs
FREQUENCY
10
0°
–10°
–20°
–30°
–40°
–50°
–60°
–70°
–80°
–90°
Phase Shift
Cref
Vref
39 kΩ
39 kΩ
+
–
Test Circuit
Figure 21
SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999
19
www.ti.com
TYPICAL CHARACTERISTICS
60
40
20
00510
Output Sink Current – mA
80
100
Collector Output Saturation Voltage – V
OUTPUT SINK CURRENT
vs
COLLECTOR OUTPUT SATURATION VOLTAGE
120
15 20
110
90
70
50
30
10
TA = –20°C
TA = 25°C
VCC = 3.6 V
TA = 85°C
Figure 22
MAXIMUM OUTPUT VOLTAGE SWING
vs
FREE-AIR TEMPERATURE
VO(ref) –0.01
VO(ref) –0.02
VO(ref) –0.03
VO(ref) –0.04
VO(ref) –0.05
VO(ref) –0.06
VO(ref) –0.07
1
0.9
0.8
0.7
0.6
0.5
–25 0 25 50 75 100
TA – Free-Air Temperature – °C
Maximum Output Voltage
Swing (Right Scale)
Maximum Output
Voltage Swing (Right Scale)
+
–RL
100 kΩ
Vvom – 1
33 kΩ
33 kΩ
VCC = 3.6 V
RL = 100 kΩ
VOM+1 = 1.25 V
VOM –1 = 1.15 V (Right Scale)
VOM –1 = 1.35 V (Left Scale)
Vref
TEST CIRCUIT
– Maximum Output Voltage Swing – VVOM
– Maximum Output Voltage Swing – VVOM
Figure 23
SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999
20 www.ti.com
TYPICAL CHARACTERISTICS
50
60
90
1000 0.5 1 1.5 2 2.5 3
Output Transistor “On” Duty Cycle – %
30
10
Dead-Time Input Voltage – V
OUTPUT TRANSISTOR ON DUTY CYCLE
vs
DEAD-TIME INPUT VOLTAGE
0
3.5 4
70
20
40
80
VCC = 3.6 V
RT = 10kΩ
CT = 330 pF
1
0.5
001020
ICC (Standby) – Standby Current – mA
2
STANDBY CURRENT
vs
SUPPLY VOLTAGE
30 40
1.5
ÁÁ
ÁÁ
CC
I
VCC – Supply Voltage – V
TA = 25°C
1.75
1.25
0.75
0.25
Figure 24 Figure 25
1
0.5
0
–25 0 25 50
ICC – Supply Current – mA
1.5
2
STANDBY CURRENT
vs
FREE-AIR TEMPERATURE
75 100
ÁÁ
ÁÁ
CC
I
TA – Free-Air Temperature – °C
Average Supply Current
VCC = 6 V, RT = 10 kΩ,
CT = 330 pF
Stand-By Current, VCC = 40 V, No Load
Stand-By Current, VCC = 3.6 V, No Load 600
400
200
0
–25 0 25 50
Maximum Continuous Power Dissipation – mW
800
1000
MAXIMUM CONTINUOUS POWER DISSIPATION
vs
FREE-AIR TEMPERATURE
1200
75 100
1100
900
700
500
300
100
16-Pin N Plastic Dip
16-Pin NS Plastic SO
Thermal Resistance
125°C/W
Thermal Resistance
250°C/W
TA – Free-Air Temperature
1.75
1.25
0.75
0.25
Figure 26 Figure 27
SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999
21
www.ti.com
APPLICATION INFORMATION
R7
R6 C4
470 Ω
1 µF
220 Ω
C2
R4
R3
33 kΩ
33 kΩ
470 Ω150 Ω
220 kΩ
0.47 µF50 kΩ
R1
500 pF
pF
C5 R5 500
C1
87654321
910111213141516
330 pF
L1
R2
33 kΩ
33 kΩ
Vref
33 kΩ33 kΩ470 Ω
470 Ω
L2
VCC
Step-Up
Output
Step-Down
Output
TL1451A
NOTE A: Values for R1 through R7, C1 through C4, and L1 and L2 depend upon individual application.
Figure 28. High-Speed Dual Switching Regulator
PACKAGING INFORMATION
Orderable Device Status (1) Package
Type Package
Drawing Pins Package
Qty Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
5962-9958401Q2A OBSOLETE LCCC FK 20 TBD Call TI Call TI
5962-9958401QEA OBSOLETE CDIP J 16 TBD Call TI Call TI
TL1451ACD ACTIVE SOIC D 16 40 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451ACDBLE NRND SSOP DB 16 TBD Call TI Call TI
TL1451ACDBR ACTIVE SSOP DB 16 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451ACDBRG4 ACTIVE SSOP DB 16 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451ACDG4 ACTIVE SOIC D 16 40 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451ACDR ACTIVE SOIC D 16 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451ACDRG4 ACTIVE SOIC D 16 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451ACN ACTIVE PDIP N 16 25 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type
TL1451ACNE4 ACTIVE PDIP N 16 25 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type
TL1451ACNSR ACTIVE SO NS 16 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451ACNSRG4 ACTIVE SO NS 16 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451ACPW ACTIVE TSSOP PW 16 90 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451ACPWG4 ACTIVE TSSOP PW 16 90 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451ACPWR ACTIVE TSSOP PW 16 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451ACPWRG4 ACTIVE TSSOP PW 16 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451AMFKB OBSOLETE LCCC FK 20 TBD Call TI Call TI
TL1451AMJB OBSOLETE CDIP J 16 TBD Call TI Call TI
TL1451AQD ACTIVE SOIC D 16 40 TBD CU NIPDAU Level-1-220C-UNLIM
TL1451AQDG4 ACTIVE SOIC D 16 40 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TL1451AQDR ACTIVE SOIC D 16 2500 TBD CU NIPDAU Level-1-220C-UNLIM
TL1451AQDRG4 ACTIVE SOIC D 16 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
PACKAGE OPTION ADDENDUM
www.ti.com 3-May-2010
Addendum-Page 1
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TL1451A, TL1451AM :
•Automotive: TL1451A-Q1
•Enhanced Product: TL1451A-EP
NOTE: Qualified Version Definitions:
•Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
•Enhanced Product - Supports Defense, Aerospace and Medical Applications
PACKAGE OPTION ADDENDUM
www.ti.com 3-May-2010
Addendum-Page 2
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0 (mm) B0 (mm) K0 (mm) P1
(mm) W
(mm) Pin1
Quadrant
TL1451ACDBR SSOP DB 16 2000 330.0 16.4 8.2 6.6 2.5 12.0 16.0 Q1
TL1451ACDR SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1
TL1451ACDR SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1
TL1451ACNSR SO NS 16 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.0 Q1
TL1451ACPWR TSSOP PW 16 2000 330.0 12.4 7.0 5.6 1.6 8.0 12.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 19-Mar-2008
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
TL1451ACDBR SSOP DB 16 2000 346.0 346.0 33.0
TL1451ACDR SOIC D 16 2500 346.0 346.0 33.0
TL1451ACDR SOIC D 16 2500 333.2 345.9 28.6
TL1451ACNSR SO NS 16 2000 346.0 346.0 33.0
TL1451ACPWR TSSOP PW 16 2000 346.0 346.0 29.0
PACKAGE MATERIALS INFORMATION
www.ti.com 19-Mar-2008
Pack Materials-Page 2
MECHANICAL DATA
MLCC006B – OCTOBER 1996
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
FK (S-CQCC-N**) LEADLESS CERAMIC CHIP CARRIER
4040140/D 10/96
28 TERMINAL SHOWN
B
0.358
(9,09)
MAX
(11,63)
0.560
(14,22)
0.560
0.458
0.858
(21,8)
1.063
(27,0)
(14,22)
A
NO. OF
MINMAX
0.358
0.660
0.761
0.458
0.342
(8,69)
MIN
(11,23)
(16,26)
0.640
0.739
0.442
(9,09)
(11,63)
(16,76)
0.962
1.165
(23,83)
0.938
(28,99)
1.141
(24,43)
(29,59)
(19,32)(18,78)
**
20
28
52
44
68
84
0.020 (0,51)
TERMINALS
0.080 (2,03)
0.064 (1,63)
(7,80)
0.307
(10,31)
0.406
(12,58)
0.495
(12,58)
0.495
(21,6)
0.850
(26,6)
1.047
0.045 (1,14)
0.045 (1,14)
0.035 (0,89)
0.035 (0,89)
0.010 (0,25)
12
1314151618 17
11
10
8
9
7
5
432
0.020 (0,51)
0.010 (0,25)
6
12826 27
19
21
B SQ
A SQ 22
23
24
25
20
0.055 (1,40)
0.045 (1,14)
0.028 (0,71)
0.022 (0,54)
0.050 (1,27)
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a metal lid.
D. The terminals are gold plated.
E. Falls within JEDEC MS-004
MECHANICAL DATA
MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE
4040065 /E 12/01
28 PINS SHOWN
Gage Plane
8,20
7,40
0,55
0,95
0,25
38
12,90
12,30
28
10,50
24
8,50
Seating Plane
9,907,90
30
10,50
9,90
0,38
5,60
5,00
15
0,22
14
A
28
1
2016
6,50
6,50
14
0,05 MIN
5,905,90
DIM
A MAX
A MIN
PINS **
2,00 MAX
6,90
7,50
0,65 M
0,15
0°–ā8°
0,10
0,09
0,25
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-150
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,65 M
0,10
0,10
0,25
0,50
0,75
0,15 NOM
Gage Plane
28
9,80
9,60
24
7,90
7,70
2016
6,60
6,40
4040064/F 01/97
0,30
6,60
6,20
80,19
4,30
4,50
7
0,15
14
A
1
1,20 MAX
14
5,10
4,90
8
3,10
2,90
A MAX
A MIN
DIM PINS **
0,05
4,90
5,10
Seating Plane
0°–8°
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-153
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Amplifiers amplifier.ti.com Audio www.ti.com/audio
Data Converters dataconverter.ti.com Automotive www.ti.com/automotive
DLP® Products www.dlp.com Communications and www.ti.com/communications
Telecom
DSP dsp.ti.com Computers and www.ti.com/computers
Peripherals
Clocks and Timers www.ti.com/clocks Consumer Electronics www.ti.com/consumer-apps
Interface interface.ti.com Energy www.ti.com/energy
Logic logic.ti.com Industrial www.ti.com/industrial
Power Mgmt power.ti.com Medical www.ti.com/medical
Microcontrollers microcontroller.ti.com Security www.ti.com/security
RFID www.ti-rfid.com Space, Avionics & www.ti.com/space-avionics-defense
Defense
RF/IF and ZigBee® Solutions www.ti.com/lprf Video and Imaging www.ti.com/video
Wireless www.ti.com/wireless-apps
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2010, Texas Instruments Incorporated
