LT1965 Series 1.1A, Low Noise, Low Dropout Linear Regulator FEATURES DESCRIPTION n The LT(R)1965 series are low noise, low dropout linear regulators. The devices supply 1.1A of output current with a 310mV typical dropout voltage. Operating quiescent current is 500A for the adjustable version, reducing to <1A in shutdown. Quiescent current is well controlled; it does not rise in dropout as with many other regulators. The LT1965 regulators have very low output noise which makes them ideal for sensitive RF and DSP supply applications. n n n n n n n n n n n n n n n n Output Current: 1.1A Dropout Voltage: 310mV Low Noise: 40VRMS (10Hz to 100kHz) 500A Quiescent Current (Adjustable Version) Wide Input Voltage Range: 1.8V to 20V No Protection Diodes Needed Controlled Quiescent Current in Dropout Adjustable Output from 1.20V to 19.5V Fixed Output Voltages: 1.5V, 1.8V, 2.5V, 3.3V < 1A Quiescent Current in Shutdown Stable with 10F Output Capacitor Stable with Ceramic, Tantalum or Aluminum Electrolytic Capacitors Reverse Battery Protection No Reverse Current Current Limit with Foldback Protection Thermal Limiting 5-Lead TO-220, DD-PAK, Thermally Enhanced 8-Lead MSOP and 8-Lead 3mm x 3mm DFN Packages APPLICATIONS n n n Output voltage ranges from 1.20V to 19.5V. The LT1965 regulators are stable with output capacitors as low as 10F. Internal protection circuitry includes reverse battery protection, current limiting with foldback, thermal limiting and reverse current protection. The LT1965 series are available in fixed output voltages of 1.5V, 1.8V, 2.5V, 3.3V, and as an adjustable device with a 1.20V reference voltage. The package offerings include the 5-lead TO-220, 5-lead DD-PAK as well as the thermally enhanced 8-lead MSOP and low-profile (0.75mm) 8-lead 3mm x 3mm DFN. L, LT, LTC and LTM are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Logic Power Supplies Post Regulator for Switching Supplies Low Noise Instrumentation TYPICAL APPLICATION Dropout Voltage 3.3V to 2.5V Regulator IN + 10F* OUT LT1965-2.5 SHDN 2.5V 1.1A + 10F* SENSE GND 1965 TA01 *CERAMIC, TANTALUM OR ALUMINUM ELECTROLYTIC TJ = 25C 350 DROPOUT VOLTAGE (mV) VIN > 3V TO 20V 400 300 250 200 150 100 50 0 0 0.2 0.6 0.8 0.4 OUTPUT CURRENT (A) 1 1.2 1965 TA01b 1965fa 1 LT1965 Series ABSOLUTE MAXIMUM RATINGS (Note 1) IN Pin Voltage .........................................................22V OUT Pin Voltage ......................................................22V Input to Output Differential Voltage (Note 2) ......... 22V SENSE Pin Voltage ..................................................22V ADJ Pin Voltage ........................................................9V SHDN Pin Voltage ...................................................22V Output Short-Circuit Duration .......................... Indefinite Operating Junction Temperature Range (E, I Grade) (Notes 2, 13)......................................-40C to 125C Storage Temperature Range...................-65C to 150C Lead Temperature (Soldering, 10 sec) (Only for MSOP, TO-220, DD-PAK Packages) .... 300C PIN CONFIGURATION TOP VIEW OUT 1 8 IN OUT 2 7 IN 6 SHDN 5 GND SENSE/ADJ* 3 9 GND 4 TOP VIEW OUT OUT SENSE/ADJ* GND 1 2 3 4 8 7 6 5 9 IN IN SHDN GND MS8E PACKAGE 8-LEAD PLASTIC MSOP DD PACKAGE 8-LEAD (3mm x 3mm) PLASTIC DFN TJMAX = 125C, JA = 65C/W, JC = 3C/W EXPOSED PAD (PIN 9) IS GND, MUST BE SOLDERED TO PCB *PIN 3 = SENSE FOR LT1965-1.5/LT1965-1.8/LT1965-2.5/LT1965-3.3 *PIN 3 = ADJ FOR LT1965 TJMAX = 125C, JA = 60C/W, JC = 10C/W EXPOSED PAD (PIN 9) IS GND, MUST BE SOLDERED TO PCB *PIN 3 = SENSE FOR LT1965-1.5/LT1965-1.8/LT1965-2.5/LT1965-3.3 *PIN 3 = ADJ FOR LT1965 FRONT VIEW TAB IS GND FRONT VIEW 5 SENSE/ADJ* 5 SENSE/ADJ* 4 OUT 4 OUT 3 GND 3 GND 2 IN 2 IN 1 SHDN 1 SHDN TAB IS GND Q PACKAGE 5-LEAD PLASTIC DD-PAK T PACKAGE 5-LEAD PLASTIC TO-220 TJMAX = 125C, JA = 30C/W, JC = 3C/W *PIN 5 = SENSE FOR LT1965-1.5/LT1965-1.8/LT1965-2.5/LT1965-3.3 *PIN 5 = ADJ FOR LT1965 TJMAX = 125C, JA = 50C/W, JC = 3C/W *PIN 5 = SENSE FOR LT1965-1.5/LT1965-1.8/LT1965-2.5/LT1965-3.3 *PIN 5 = ADJ FOR LT1965 ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LT1965EDD#PBF LT1965EDD#TRPBF LCXW 8-Lead (3mm x 3mm) Plastic DFN -40C to 125C LT1965IDD#PBF LT1965IDD#TRPBF LCXW 8-Lead (3mm x 3mm) Plastic DFN -40C to 125C LT1965EDD-1.5#PBF LT1965EDD-1.5#TRPBF LDKW 8-Lead (3mm x 3mm) Plastic DFN -40C to 125C LT1965IDD-1.5#PBF LT1965IDD-1.5#TRPBF LDKW 8-Lead (3mm x 3mm) Plastic DFN -40C to 125C LT1965EDD-1.8#PBF LT1965EDD-1.8#TRPBF LDKY 8-Lead (3mm x 3mm) Plastic DFN -40C to 125C LT1965IDD-1.8#PBF LT1965IDD-1.8#TRPBF LDKY 8-Lead (3mm x 3mm) Plastic DFN -40C to 125C LT1965EDD-2.5#PBF LT1965EDD-2.5#TRPBF LDMB 8-Lead (3mm x 3mm) Plastic DFN -40C to 125C LT1965IDD-2.5#PBF LT1965IDD-2.5#TRPBF LDMB 8-Lead (3mm x 3mm) Plastic DFN -40C to 125C LT1965EDD-3.3#PBF LT1965EDD-3.3#TRPBF LDMD 8-Lead (3mm x 3mm) Plastic DFN -40C to 125C LT1965IDD-3.3#PBF LT1965IDD-3.3#TRPBF LDMD 8-Lead (3mm x 3mm) Plastic DFN -40C to 125C 1965fa 2 LT1965 Series ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LT1965EMS8E#PBF LT1965EMS8E#TRPBF LTCXX 8-Lead Plastic MSOP -40C to 125C LT1965IMS8E#PBF LT1965IMS8E#TRPBF LTCXX 8-Lead Plastic MSOP -40C to 125C LT1965EMS8E-1.5#PBF LT1965EMS8E-1.5#TRPBF LTDKX 8-Lead Plastic MSOP -40C to 125C LT1965IMS8E-1.5#PBF LT1965IMS8E-1.5#TRPBF LTDKX 8-Lead Plastic MSOP -40C to 125C LT1965EMS8E-1.8#PBF LT1965EMS8E-1.8#TRPBF LTDKZ 8-Lead Plastic MSOP -40C to 125C LT1965IMS8E-1.8#PBF LT1965IMS8E-1.8#TRPBF LTDKZ 8-Lead Plastic MSOP -40C to 125C LT1965EMS8E-2.5#PBF LT1965EMS8E-2.5#TRPBF LTDMC 8-Lead Plastic MSOP -40C to 125C LT1965IMS8E-2.5#PBF LT1965IMS8E-2.5#TRPBF LTDMC 8-Lead Plastic MSOP -40C to 125C LT1965EMS8E-3.3#PBF LT1965EMS8E-3.3#TRPBF LTDMF 8-Lead Plastic MSOP -40C to 125C LT1965IMS8E-3.3#PBF LT1965IMS8E-3.3#TRPBF LTDMF 8-Lead Plastic MSOP -40C to 125C LT1965EQ#PBF LT1965EQ#TRPBF LT1965Q 5-Lead Plastic DD-PAK -40C to 125C LT1965IQ#PBF LT1965IQ#TRPBF LT1965Q 5-Lead Plastic DD-PAK -40C to 125C LT1965EQ-1.5#PBF LT1965EQ-1.5#TRPBF LT1965Q-1.5 5-Lead Plastic DD-PAK -40C to 125C LT1965IQ-1.5#PBF LT1965IQ-1.5#TRPBF LT1965Q-1.5 5-Lead Plastic DD-PAK -40C to 125C LT1965EQ-1.8#PBF LT1965EQ-1.8#TRPBF LT1965Q-1.8 5-Lead Plastic DD-PAK -40C to 125C LT1965IQ-1.8#PBF LT1965IQ-1.8#TRPBF LT1965Q-1.8 5-Lead Plastic DD-PAK -40C to 125C LT1965EQ-2.5#PBF LT1965EQ-2.5#TRPBF LT1965Q-2.5 5-Lead Plastic DD-PAK -40C to 125C LT1965IQ-2.5#PBF LT1965IQ-2.5#TRPBF LT1965Q-2.5 5-Lead Plastic DD-PAK -40C to 125C LT1965EQ-3.3#PBF LT1965EQ-3.3#TRPBF LT1965Q-3.3 5-Lead Plastic DD-PAK -40C to 125C LT1965IQ-3.3#PBF LT1965IQ-3.3#TRPBF LT1965Q-3.3 5-Lead Plastic DD-PAK -40C to 125C LT1965ET#PBF LT1965ET#TRPBF LT1965T 5-Lead Plastic TO-220 -40C to 125C LT1965IT#PBF LT1965IT#TRPBF LT1965T 5-Lead Plastic TO-220 -40C to 125C LT1965ET-1.5#PBF LT1965ET-1.5#TRPBF LT1965T-1.5 5-Lead Plastic TO-220 -40C to 125C LT1965IT-1.5#PBF LT1965IT-1.5#TRPBF LT1965T-1.5 5-Lead Plastic TO-220 -40C to 125C LT1965ET-1.8#PBF LT1965ET-1.8#TRPBF LT1965T-1.8 5-Lead Plastic TO-220 -40C to 125C LT1965IT-1.8#PBF LT1965IT-1.8#TRPBF LT1965T-1.8 5-Lead Plastic TO-220 -40C to 125C LT1965ET-2.5#PBF LT1965ET-2.5#TRPBF LT1965T-2.5 5-Lead Plastic TO-220 -40C to 125C LT1965IT-2.5#PBF LT1965IT-2.5#TRPBF LT1965T-2.5 5-Lead Plastic TO-220 -40C to 125C LT1965ET-3.3#PBF LT1965ET-3.3#TRPBF LT1965T-3.3 5-Lead Plastic TO-220 -40C to 125C LT1965IT-3.3#PBF LT1965IT-3.3#TRPBF LT1965T-3.3 5-Lead Plastic TO-220 -40C to 125C Consult LTC Marketing for parts specified with wider operating temperature ranges. *Temperature grades are identified by a label on the shipping container. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 1965fa 3 LT1965 Series ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 3) PARAMETER CONDITIONS TYP MAX Minimum Input Voltage (Notes 4, 12) ILOAD = 0.5A ILOAD = 1.1A l 1.65 1.8 2.3 V V LT1965-1.5, VIN = 2.1V, ILOAD = 1mA LT1965-1.5, 2.5 < VIN < 20V, 1mA < ILOAD < 1.1A l 1.477 1.455 1.5 1.5 1.523 1.545 V V LT1965-1.8, VIN = 2.3V, ILOAD = 1mA LT1965-1.8, 2.8 < VIN < 20V, 1mA < ILOAD < 1.1A l 1.773 1.746 1.8 1.8 1.827 1.854 V V LT1965-2.5, VIN = 3V, ILOAD = 1mA LT1965-2.5, 3.5 < VIN < 20V, 1mA < ILOAD < 1.1A l 2.462 2.425 2.5 2.5 2.538 2.575 V V LT1965-3.3, VIN = 3.8V, ILOAD = 1mA LT1965-3.3, 4.3 < VIN < 20V, 1mA < ILOAD < 1.1A l 3.25 3.201 3.3 3.3 3.35 3.399 V V ADJ Pin Voltage (Notes 4, 5) VIN = 2.1V, ILOAD = 1mA 2.3V < VIN < 20V, 1mA < ILOAD < 1.1A l 1.182 1.164 1.2 1.2 1.218 1.236 V V Line Regulation LT1965-1.5, VIN = 2.1V to 20V, ILOAD = 1mA LT1965-1.8, VIN = 2.3V to 20V, ILOAD = 1mA LT1965-2.5, VIN = 3V to 20V, ILOAD = 1mA LT1965-3.3, VIN = 3.8V to 20V, ILOAD = 1mA LT1965, VIN = 2.1V to 20V, ILOAD = 1mA (Note 4) l l l l l 3.5 4 4.5 5.5 3 9 10 11.5 16 8 mV mV mV mV mV Load Regulation LT1965-1.5, VIN = 2.5V, ILOAD = 1mA to 1.1A LT1965-1.5, VIN = 2.5V, ILOAD = 1mA to 1.1A l 5.25 10 20 mV mV LT1965-1.8, VIN = 2.8V, ILOAD = 1mA to 1.1A LT1965-1.8, VIN = 2.8V, ILOAD = 1mA to 1.1A l 6.25 12 24 mV mV LT1965-2.5, VIN = 3.5V, ILOAD = 1mA to 1.1A LT1965-2.5, VIN = 3.5V, ILOAD = 1mA to 1.1A l 8.75 16.5 33 mV mV LT1965-3.3, VIN = 4.3V, ILOAD = 1mA to 1.1A LT1965-3.3, VIN = 4.3V, ILOAD = 1mA to 1.1A l 11.5 22 44 mV mV LT1965, LT1965, l 4.25 8 16 mV mV 0.055 0.08 0.14 V V 0.12 0.175 0.28 V V 0.21 0.25 0.36 V V 0.31 0.36 0.49 V V 0.5 0.6 2.2 8.2 21 1.1 1.5 5.5 20 40 mA mA mA mA mA Regulated Output Voltage (Note 5) Dropout Voltage VIN = VOUT(NOMINAL) (Notes 6, 7, 12) VIN = 2.3V, ILOAD = 1mA to 1.1A (Note 4) VIN = 2.3V, ILOAD = 1mA to 1.1A (Note 4) MIN ILOAD = 1mA ILOAD = 1mA l ILOAD = 100mA ILOAD = 100mA l ILOAD = 500mA ILOAD = 500mA l ILOAD = 1.1A ILOAD = 1.1A l GND Pin Current VIN = VOUT(NOMINAL) + 1V (Notes 6, 8) ILOAD = 0mA ILOAD = 1mA ILOAD = 100mA ILOAD = 500mA ILOAD = 1.1A l l l l l Output Voltage Noise COUT = 10F, ILOAD = 1.1A, BW = 10Hz to 100kHz 40 ADJ Pin Bias Current (Notes 4, 9) Shutdown Threshold VOUT = Off to On VOUT = On to Off l l 0.2 UNITS VRMS 1.3 4.5 A 0.85 0.45 2 V V SHDN Pin Current (Note 10) VSHDN = 0V VSHDN = 20V 0.01 5.5 1 10 A A Quiescent Current in Shutdown VIN = 6V, VSHDN = 0V 0.01 1 A Ripple Rejection VIN - VOUT = 1.5V (AVG), VRIPPLE = 0.5VP-P, fRIPPLE = 120Hz, ILOAD = 0.75A 57 75 dB 1965fa 4 LT1965 Series ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 3) PARAMETER CONDITIONS Current Limit VIN = 7V, VOUT = 0 VIN = VOUT(NOMINAL) + 1V, VOUT = -0.1V (Note 6) MIN Input Reverse Leakage Current VIN = -20V, VOUT = 0 Reverse Output Current (Note 11) LT1965-1.5, VOUT = 1.5V, VIN = 0 LT1965-1.8, VOUT = 1.8V, VIN = 0 LT1965-2.5, VOUT = 2.5V, VIN = 0 LT1965-3.3, VOUT = 3.3V, VIN = 0 LT1965 (Note 4), VOUT = 1.2V, VIN = 0 Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: Absolute maximum input to output differential voltage is not achievable with all combinations of rated IN pin and OUT pin voltages. With the IN pin at 22V, the OUT pin may not be pulled below 0V. The total measured voltage from IN to OUT must not exceed 22V. Note 3: The LT1965 regulators are tested and specified under pulse load conditions such that TJ TA. The LT1965E regulators are 100% tested at TA = 25C. Performance at -40C and 125C is assured by design, characterization, and correlation with statistical process controls. The LT1965I regulators are guaranteed over the full -40C to 125C operating junction temperature range. Note 4: The LT1965 adjustable version is tested and specified for these conditions with the ADJ connected to the OUT pin. Note 5: Maximum junction temperature limits operating conditions. The regulated output voltage specification does not apply for all possible combinations of input voltage and output current. Limit the output current range if operating at the maximum input voltage. Limit the input-to-output voltage differential if operating at the maximum output current. Note 6: To satisfy minimum input voltage requirements, the LT1965 adjustable version is tested and specified for these conditions with an external resistor divider (bottom 4.02k, top 4.32k) for an output voltage of l TYP MAX 2.4 A A 1.2 275 275 275 275 175 UNITS 1 mA 525 525 525 525 400 A A A A A 2.5V. The external resistor divider adds 300A of output DC load current. This external current is not factored into GND pin current. Note 7: Dropout voltage is the minimum input-to-output voltage differential needed to maintain regulation at a specified output current. In dropout, the output voltage equals: (VIN - VDROPOUT) Note 8: GND pin current is tested with VIN = VOUT(NOMINAL) + 1V and a current source load. GND pin current increases slightly in dropout. For the fixed output versions, an internal resistor divider will typically add 100A to the GND pin current. See GND pin current curves in the Typical Performance Characteristics section. Note 9: ADJ pin bias current flows into the ADJ pin. Note 10: SHDN pin current flows into the SHDN pin. Note 11: Reverse output current is tested with the IN pin grounded and the OUT pin forced to the rated output voltage. This current flows into the OUT pin and out of the GND pin. Note 12: For the LT1965, LT1965-1.5 and LT1965-1.8, the minimum input voltage specification limits the dropout voltage under some output voltage/load conditions. Note 13: This IC includes overtemperature protection that is intended to protect the device during momentary overload conditions. Junction temperature will exceed 125C when overtemperature is active. Continuous operation above the specified maximum operating junction temperature may impair device reliability. 1965fa 5 LT1965 Series TYPICAL PERFORMANCE CHARACTERISTICS Typical Dropout Voltage Guaranteed Dropout Voltage GUARANTEED DROPOUT VOLTAGE (mV) 500 DROPOUT VOLTAGE (mV) 450 400 TJ = 125C 350 300 250 200 TJ = 25C 150 100 50 0 0.2 0 0.6 0.8 0.4 OUTPUT CURRENT (A) 1 = TEST POINTS 450 450 400 TJ = 125C 350 300 TJ = 25C 250 200 150 0.2 0.6 0.8 0.4 OUTPUT CURRENT (A) 0.6 LT1965 0.5 0.4 0.3 0.2 0.1 -25 0 25 50 75 TEMPERATURE (C) 100 IL = 1mA 1.517 1.821 1.512 1.815 1.507 1.502 1.497 1.492 125 1.797 1.791 1.779 1.773 -50 -25 0 25 50 75 TEMPERATURE (C) 100 125 3.340 IL = 1mA 2.500 2.492 2.484 3.310 3.300 3.290 3.280 1.206 1.198 1.194 2.468 3.260 1.186 2.460 -50 3.250 -50 0 25 50 75 TEMPERATURE (C) 100 125 1965 G07 IL = 1mA 1.202 1.190 -25 125 1.210 3.320 3.270 2.476 100 1.214 ADJ PIN VOLTAGE (V) OUTPUT VOLTAGE (V) 2.508 0 25 50 75 TEMPERATURE (C) LT1965 ADJ Pin Voltage 1.218 3.330 2.516 -25 1965 G06 LT1965-3.3 Output Voltage 2.524 OUTPUT VOLTAGE (V) 1.809 1965 G05 IL = 1mA 125 1.803 1.482 3.350 100 IL = 1mA 1.477 -50 LT1965-2.5 Output Voltage 2.532 0 25 50 75 TEMPERATURE (C) 1.785 1965 G04 2.540 -25 LT1965-1.8 Output Voltage 1.827 1.487 0 -50 IL = 1mA 1965 G03 OUTPUT VOLTAGE (V) LT1965-1.5/-1.8/-2.5/-3.3 IL = 100mA 0 -50 1.2 LT1965-1.5 Output Voltage 1.522 VIN = 6V RL = , IL = 0 VSHDN = VIN 0.7 200 150 1965 G02 OUTPUT VOLTAGE (V) QUIESCENT CURRENT (mA) 0.8 1 IL = 500mA 250 50 Quiescent Current 0.9 300 50 0 IL = 1.1A 350 100 0 1.2 400 100 1965 G01 1.0 Dropout Voltage 500 DROPOUT VOLTAGE (mV) 500 -25 0 25 50 75 TEMPERATURE (C) 100 125 1965 G08 1.182 -50 -25 0 25 50 75 TEMPERATURE (C) 100 125 1965 G09 1965fa 6 LT1965 Series TYPICAL PERFORMANCE CHARACTERISTICS LT1965-1.5 Quiescent Current LT1965-1.8 Quiescent Current 5 4 3 2 VSHDN = VIN VSHDN = 0V 0 0 1 2 3 4 5 6 7 INPUT VOLTAGE (V) TJ = 25C RL = 4 3 2 1 VSHDN = VIN VSHDN = 0V 0 8 9 0 10 1 2 3 4 5 6 7 INPUT VOLTAGE (V) LT1965-3.3 Quiescent Current 1.0 4 VSHDN = 0V VSHDN = VIN 8 9 0.6 VSHDN = VIN 0.5 0.4 0.3 0.2 RL = 3, IL = 500mA* 5 8 2 4 6 8 10 12 14 16 18 20 INPUT VOLTAGE (V) 3 2 RL = 30, IL = 50mA* RL = 150, IL = 10mA* 0 1 2 3 4 5 6 7 INPUT VOLTAGE (V) 8 9 10 1965 G15 LT1965-1.8 GND Pin Current (Heavy Load) 3 2 RL = 36, IL = 50mA* RL = 180, IL = 10mA* 1 10 0 25 TJ = 25C VSHDN = VIN *FOR VOUT = 1.8V 4 9 RL = 1.5k, IL = 1mA* VSHDN = 0V 5 GND PIN CURRENT (mA) GND PIN CURRENT (mA) 10 3 4 5 6 7 INPUT VOLTAGE (V) TJ = 25C VSHDN = VIN *FOR VOUT = 1.5V 4 LT1965-1.8 GND Pin Current (Light Load) RL = 1.363, IL = 1.1A* 2 1965 G14 TJ = 25C VSHDN = VIN *FOR VOUT = 1.5V 15 1 1 0 10 LT1965-1.5 GND Pin Current (Heavy Load) 20 VSHDN = VIN 1965 G12 5 1965 G13 25 VSHDN = 0V LT1965-1.5 GND Pin Current (Light Load) 0.7 0 3 4 5 6 7 INPUT VOLTAGE (V) 2 0 0.8 0.1 0 2 4 10 GND PIN CURRENT (mA) 6 1 9 TJ = 25C RL = 4.02k 0.9 QUIESCENT CURRENT (mA) QUIESCENT CURRENT (mA) 8 0 6 LT1965 Quiescent Current TJ = 25C RL = 2 8 1965 G11 1965 G10 10 TJ = 25C RL = 0 8 GND PIN CURRENT (mA) 1 LT1965-2.5 Quiescent Current 10 QUIESCENT CURRENT (mA) TJ = 25C RL = QUIESCENT CURRENT (mA) QUIESCENT CURRENT (mA) 5 TJ = 25C VSHDN = VIN *FOR VOUT = 1.8V 20 RL = 1.636, IL = 1.1A* 15 10 RL = 3.6, IL = 500mA* 5 RL = 18, IL = 100mA* RL = 1.8k, IL = 1mA* RL = 15, IL = 100mA* 0 0 1 2 3 4 5 6 7 INPUT VOLTAGE (V) 8 0 9 10 1965 G16 0 0 1 2 3 4 5 6 7 INPUT VOLTAGE (V) 8 9 10 1965 G17 0 1 2 3 4 5 6 7 INPUT VOLTAGE (V) 8 9 10 1965 G18 1965fa 7 LT1965 Series TYPICAL PERFORMANCE CHARACTERISTICS 25 12 GND PIN CURRENT (mA) TJ = 25C VSHDN = VIN *FOR VOUT = 2.5V 10 8 6 4 RL = 250, IL = 10mA* RL = 2.5k, IL = 1mA* 20 RL = 2.272, IL = 1.1A* 15 10 RL = 5, IL = 500mA* 1 2 3 4 5 6 7 INPUT VOLTAGE (V) 8 9 1 2 3 4 5 6 7 INPUT VOLTAGE (V) 8 LT1965-3.3 GND Pin Current (Heavy Load) 2.0 15 RL = 6.6, IL = 500mA* TJ = 25C VSHDN = VIN *FOR VOUT = 1.2V 1.8 GND PIN CURRENT (mA) RL = 3, IL = 1.1A* 10 5 9 10 0 2 3 4 5 6 7 INPUT VOLTAGE (V) 8 9 1.6 RL = 24, IL = 50mA* 1.4 1.2 1.0 0.8 RL = 120, IL = 10mA* 0.6 RL = 1.2k, IL = 1mA* 2 3 4 5 6 7 INPUT VOLTAGE (V) 8 10 20 RL = 1.091, IL = 1.1A* 15 10 RL = 2.4, IL = 500mA* 5 RL = 12, IL = 100mA* 0 0 10 9 TJ = 25C VSHDN = VIN *FOR VOUT = 1.2V 0.2 1 2 3 4 5 6 7 INPUT VOLTAGE (V) 8 9 0 10 1 2 3 4 5 6 7 INPUT VOLTAGE (V) 8 9 10 1965 G24 1965 G23 SHDN Pin Threshold GND Pin Current vs ILOAD 1.0 VIN = VOUT(NOMINAL) + 1V 22.5 0.9 20.0 0.8 SHDN PIN THRESHOLD (V) GND PIN CURRENT (mA) 1 25 1965 G22 25.0 0 LT1965 GND Pin Current (Heavy Load) 0 1 RL = 66, IL = 50mA* 1965 G21 0.4 RL = 33, IL = 100mA* 0 RL = 3.3k, IL = 1mA* LT1965 GND Pin Current (Light Load) TJ = 25C VSHDN = VIN *FOR VOUT = 3.3V 20 RL = 330, IL = 10mA* 4 1965 G20 1965 G19 25 6 0 0 10 8 2 0 0 TJ = 25C VSHDN = VIN *FOR VOUT = 3.3V 10 RL = 25, IL = 100mA* 0 GND PIN CURRENT (mA) 12 TJ = 25C VSHDN = VIN *FOR VOUT = 2.5V 5 RL = 50, IL = 50mA* 2 LT1965-3.3 GND Pin Current (Light Load) GND PIN CURRENT (mA) GND PIN CURRENT (mA) LT1965-2.5 GND Pin Current (Heavy Load) GND PIN CURRENT (mA) LT1965-2.5 GND Pin Current (Light Load) 17.5 15.0 12.5 10.0 7.50 5.00 OFF TO ON 0.7 0.6 ON TO OFF 0.5 0.4 0.3 0.2 0.1 2.50 0 0 0.2 0.6 0.8 0.4 LOAD CURRENT (A) 1.0 1.2 1965 G09 0 -50 -25 0 25 50 75 TEMPERATURE (C) 100 125 1965 G26 1965fa 8 LT1965 Series TYPICAL PERFORMANCE CHARACTERISTICS SHDN Pin Input Current SHDN Pin Input Current 6.0 5.9 4 3 2 1 ADJ Pin Bias Current 4.5 VSHDN = 20V 4.0 5.8 ADJ PIN BIAS CURRENT (A) 5 SHDN PIN INPUT CURRENT (A) SHDN PIN INPUT CURRENT (A) 6 5.7 5.6 5.5 5.4 5.3 5.2 2 4 5.0 -50 6 8 10 12 14 16 18 20 SHDN PIN VOLTAGE (V) -25 0 25 50 75 TEMPERATURE (C) 100 1965 G11 CURRENT LIMIT (A) TJ = 25C 1.0 0.5 VIN = 7V VOUT = 0V 2.0 1.5 1.0 0.5 0.0 2 4 6 8 10 12 14 16 18 INPUT/OUTPUT DIFFERENTIAL (V) 20 0 -50 -25 0 25 50 75 TEMPERATURE (C) 0.40 0.35 0.30 0.20 LT1965 0.10 0.05 0.00 -50 -25 0 25 50 75 TEMPERATURE (C) TJ = 25C VIN = 0V VOUT = VADJ (LT1965) VOUT = VSENSE (LT1965-1.5/-1.8/-2.5/-3.3) CURRENT FLOWS INTO OUTPUT PIN 5 4 3 100 125 LT1965 LT1965-1.5 2 LT1965-1.8 1 LT1965-3.3 0 1 2 LT1965-2.5 3 4 5 6 7 OUTPUT VOLTAGE (V) 8 9 1965 G32 80 LT1965-1.5/-1.8/-2.5/-3.3 0.15 6 90 VIN = 0V VOUT = 1.2V (LT1965) VOUT = 1.5V (LT1965-1.5) VOUT = 1.8V (LT1965-1.8) VOUT = 2.5V (LT1965-2.5) VOUT = 3.3V (LT1965-3.3) 0.25 125 Ripple Rejection vs Frequency Reverse Output Current 0.45 100 1965 G13 1965 G15 1965 G30 0.50 0 25 50 75 TEMPERATURE (C) 0 RIPPLE REJECTION (dB) 0 REVERSE OUTPUT CURRENT (mA) CURRENT LIMIT (A) TJ = -50C -25 Reverse Output Current 2.5 2.0 TJ = 125C 1.0 Current Limit vs Temperature 3.0 VOUT = 100mV 1.5 2.0 1.5 1965 G12 Current Limit vs VIN - VOUT 2.5 2.5 0 -50 125 REVERSE OUTPUT CURRENT (mA) 0 3.0 0.5 5.1 0 3.5 100 125 1965 G33 70 60 50 40 30 20 IL = 0.75A COUT = 10F CERAMIC 10 VIN = VOUT(NOMINAL) + 1V + 50mVRMS RIPPLE 0 10 100 1k 10k FREQUENCY (Hz) 100k 1M 1965 G34 1965fa 9 LT1965 Series TYPICAL PERFORMANCE CHARACTERISTICS Ripple Rejection vs Temperature LT1965 Minimum Input Voltage 100 Load Regulation 0 2.5 90 80 70 IL = 0.75A VIN = VOUT(NOMINAL) + 1V + 0.5P-P RIPPLE AT f = 120Hz 60 -50 -25 0 25 50 75 TEMPERATURE (C) 100 2.0 IL = 1.1A 1.5 IL = 500mA 1.0 0.5 -25 0 25 50 75 TEMPERATURE (C) 100 1965 G35 OUTPUT NOISE VOLTAGE (VRMS) OUTPUT NOISE SPECTRAL DENSITY (V Hz) LT1965-3.3 0.10 LT1965 LT1965-1.8 LT1965-1.5 VIN = VOUT(NOMINAL) + 1V (LT1965-1.5/-1.8/-2.5/-3.3) VIN = 2.3V (LT1965) IL = 1mA TO 1.1A -30 -50 -25 0 25 50 75 TEMPERATURE (C) 100 125 1965 G37 LT1965-1.8 10Hz to 100kHz Output Noise 100 1k 10k COUT = 10F 70 IL = 1.1A 60 LT1965-3.3 50 LT1965-2.5 LT1965-1.8 30 20 LT1965 400s/DIV LT1965-1.5 10 0 0.0001 100k 0.001 1 0.01 0.1 LOAD CURRENT (A) SHDN AND OUTPUT VOLTAGE (V) OUTPUT VOLTAGE DEVIATION (mV) 4.0 VOUT = 3.3V 50 0 -50 LOAD CURRENT (A) -100 VIN = 4.3V CIN = 10F CERAMIC COUT = 10F CERAMIC 1.0 0.5 0.0 0 10 20 10 LT1965-2.5 SHDN Transient Response LT1965-3.3 Transient Response 1.5 1965 G40 1965 G39 1965 G38 100 VOUT 100V/DIV 40 FREQUENCY (Hz) 30 40 50 TIME (s) 60 70 80 1965 G41 10 LT1965-3.3 80 COUT = 10F IL = 1.1A 10 LT1965-2.5 -20 RMS Output Noise vs Load Current (10Hz to 100kHz) LT1965-2.5 0.01 LT1965-1.8 -15 1965 G36 Output Noise Spectral Density 1.00 125 LT1965 -10 -25 0 -50 125 IL = 100mA LOAD REGULATION (mV) MINIMUM INPUT VOLTAGE (V) RIPPLE REJECTION (dB) LT1965-1.5 -5 3.5 SHDN 3.0 2.5 2.0 1.5 OUTPUT 1.0 0.5 0.0 0 10 20 30 40 50 60 70 80 90 100 TIME (s) 1965 G42 VIN = 3.3V COUT = 10F CERAMIC RL = 2.5k, IL = 1mA FOR VOUT = 2.5V 1965fa LT1965 Series PIN FUNCTIONS (DFN/MSOP/DD-PAK/TO-220) OUT (Pins 1, 2 / 1, 2 / 4 / 4): Output. This pin supplies power to the load. Use a minimum output capacitor of 10F to prevent oscillations. Large load transient applications require larger output capacitors to limit peak voltage transients. See the Applications Information section for more information on output capacitance and reverse output characteristics. ADJ (Pin 3 / 3 / 5 / 5): Adjust. This pin is the input to the error amplifier. It has a typical bias current of 1.3A that flows into the pin. The ADJ pin voltage is 1.20V referenced to ground. SENSE (Pin 3 / 3 / 5 / 5): Sense. For fixed voltage versions of the LT1965 (LT1965-1.5/LT1965-1.8/ LT1965-2.5/ LT1965-3.3), the SENSE pin is the input to the error amplifier. Optimum regulation is obtained when the SENSE pin is connected to the OUT pin of the regulator. In critical applications, small voltage drops are caused by the resistance (RP) of PCB traces between the regulator and the load. These drops may be eliminated by connecting the SENSE pin to the output at the load as shown in Figure 1 (Kelvin Sense Connection). Note that the voltage drop across the external PCB traces will add to the dropout voltage of the regulator. The SENSE pin bias current is 100A at the nominal rated output voltage. The SENSE pin can be pulled below ground (as in a dual supply system where the regulator load is returned to a negative supply) while still allowing the device to start and operate. SHDN (Pin 6 / 6 / 1 / 1): Shutdown. Pulling the SHDN pin low puts the LT1965 into a low power state and turns the output off. Drive the SHDN pin with either logic or an open collector/drain with a pull-up resistor. The resistor supplies the pull-up current to the open collector/drain logic, normally several microamperes and the SHDN pin current, typically less than 5.5A. If unused, connect the SHDN pin to VIN. The SHDN pin cannot be driven below GND unless it is tied to the IN pin. If the SHDN pin is driven below GND while IN is powered, the output will turn on. SHDN pin logic cannot be referenced to a negative supply rail. IN OUT LT1965 + VIN RP SHDN SENSE LOAD + GND RP 1965 F01 Figure 1. Kelvin Sense Connection GND (Pins 4, 5 / 4, 5 / 3 / 3): Ground. For the adjustable LT1965, connect the bottom of the resistor divider, setting output voltage, directly to GND for optimum regulation. IN (Pins 7, 8 / 7, 8 / 2 / 2): Input. This pin supplies power to the device. The LT1965 requires a bypass capacitor at IN if located more than six inches from the main input filter capacitor. Include a bypass capacitor in battery-powered circuits as a battery's output impedance generally rises with frequency. A bypass capacitor in the range of 1F to 10F suffices. The LT1965's design withstands reverse voltages on the IN pin with respect to ground and the OUT pin. In the case of a reversed input, which occurs if a battery is plugged in backwards, the LT1965 behaves as if a diode is in series with its input. No reverse current flows into the LT1965 and no reverse voltage appears at the load. The device protects itself and the load. Exposed Pad (Pin 9 / 9, DFN and MSOP Packages Only): Ground. Tie this pin directly to Pins 4 and 5 and the PCB ground. This pin provides enhanced thermal performance with its connection to the PCB ground. See the Applications Information section for thermal considerations and calculating junction temperature. 1965fa 11 LT1965 Series APPLICATIONS INFORMATION The LT1965 series are 1.1A low dropout regulators with shutdown. The devices are capable of supplying 1.1A at a typical dropout voltage of 310mV. The low operating quiescent current (500A for the adjustable version, 600A for the fixed voltage versions) drops to less than 1A in shutdown. In addition to the low quiescent current, the LT1965 regulators incorporate several protection features that makes them ideal for use in battery-powered systems. The devices protect themselves against both reverse input and reverse output voltages. In battery backup applications, if a backup battery holds up the output when the input is pulled to ground, the LT1965 performs like it has a diode in series with its output, preventing reverse current flow. Also, in dual supply applications where the regulator load is returned to a negative supply, the output can be pulled below ground by as much as 20V. The LT1965 still starts and operates normally in this situation. Adjustable Operation The LT1965 adjustable version has an output voltage range of 1.20V to 19.5V. Figure 2 illustrates that the ratio of two external resistors sets the output voltage. The device servos the output to maintain the ADJ pin voltage at 1.20V referenced to ground. R1's current equals 1.20V/R1. R2's current equals R1's current plus the ADJ pin bias current. The ADJ pin bias current, 1.3A at 25C, flows through R2 into the ADJ pin. Use the formula in Figure 2 to calculate output voltage. Linear Technology recommends that R1's value be less than 12.1k to minimize output voltage errors due to the ADJ pin bias current. In shutdown, the output turns off and the divider current is zero. For curves depicting ADJ Pin Voltage vs Temperature and ADJ Pin Bias Current vs Temperature, see the Typical Performance Characteristics section. IN VIN OUT R2 LT1965 ADJ R1 GND 1965 F02 + VOUT R2 VOUT = 1.20V 1+ +IADJ * R2 R1 VADJ = 1.20V IADJ = 1.3A AT 25C OUTPUT RANGE = 1.20V TO 19.5V Figure 2. Adjustable Operation The adjustable device is tested and specified with the ADJ pin tied to the OUT pin for an output voltage of 1.20V. Specifications for output voltages greater than 1.20V are proportional to the ratio of the desired output voltage to 1.20V: VOUT/1.20V. For example, load regulation for an output current change of 1mA to 1.1A is typically -4.25mV at VOUT = 1.20V. At VOUT = 5V, load regulation is: 5V * -4.25mV = -17.71mV 1.20V Output Capacitance The LT1965's design is stable with a wide range of output capacitors. The ESR of the output capacitor affects stability, most notably with small capacitors. A minimum output capacitor of 10F with an ESR of 3 or less is recommended to prevent oscillations. The LT1965 is a low quiescent current device and output load transient response is a function of output capacitance. Larger values of output capacitance decrease the peak deviations and provide improved transient response for larger current changes. Ceramic capacitors require extra consideration. Manufacturers make ceramic capacitors with a variety of dielectrics, each with different behavior across temperature and applied voltage. The most common dielectrics used are specified with EIA temperature characteristic codes of Z5U, Y5V, X5R and X7R. The Z5U and Y5V dielectrics provide high C-V products in a small package at low cost, but exhibit strong voltage and temperature coefficients as shown in Figures 3 and 4. When used with a 5V regulator, a 16V 10F Y5V capacitor can exhibit an effective value as low as 1F to 2F for the DC bias applied and over the operating temperature range. The X5R and X7R dielectrics yield much more stable characteristics and are more suitable for use as the output capacitor. The X7R type works over a wider temperature range and has better temperature stability whereas X5R is less expensive and is available in higher values. Care still must be exercised when using X5R and X7R capacitors; the X5R and X7R codes only specify operating temperature range and maximum capacitance change over temperature. Capacitance change due to DC bias with X5R and X7R capacitors is better than Y5V and Z5U capacitors, but can still be significant enough to drop 1965fa 12 LT1965 Series APPLICATIONS INFORMATION capacitor values below appropriate levels. Capacitor DC bias characteristics tend to improve as component case size increases, but expected capacitance at operating voltages should be verified. Voltage and temperature coefficients are not the only sources of problems. Some ceramic capacitors have a piezoelectric response. A piezoelectric device generates voltage across its terminals due to mechanical stress, similar to the way a piezoelectric accelerometer or microphone works. For a ceramic capacitor, the stress can be induced by vibrations in the system or thermal transients. The resulting voltages produced can cause appreciable amounts of noise. A ceramic capacitor produced the trace in Figure 5 in response to light tapping from a pencil. Similar vibration induced behavior can masquerade as increased output voltage noise. Overload Recovery Like many IC power regulators, the LT1965 has safe operating area protection. The safe area protection decreases current limit as input-to-output voltage increases and keeps the power transistor inside a safe operating region for all values of input-to-output voltage. The protective design provides some output current at all values of input-tooutput voltage up to the device breakdown. When power is first applied, as input voltage rises, the output follows the input, allowing the regulator to start up into very heavy loads. During start-up, as the input voltage is rising, the input-to-output voltage differential is small, allowing the regulator to supply large output currents. With a high input voltage, a problem can occur wherein removal of an output short will not allow the output to 40 20 BOTH CAPACITORS ARE 16V, 1210 CASE SIZE, 10F 20 CHANGE IN VALUE (%) CHANGE IN VALUE (%) 0 X5R -20 -40 -60 Y5V -80 -100 -20 -40 2 4 8 6 10 12 DC BIAS VOLTAGE (V) 14 Y5V -60 -80 0 X5R 0 BOTH CAPACITORS ARE 16V, 1210 CASE SIZE, 10F -100 -50 -25 16 1965 F03 Figure 3. Ceramic Capacitor DC Bias Characteristics 50 25 75 0 TEMPERATURE (C) 100 125 1965 F04 Figure 4. Ceramic Capacitor Temperature Characteristics 1mV/DIV VOUT = 1.3V COUT = 10F ILOAD = 0 1ms/DIV 1965 F05 Figure 5. Noise Resulting from Tapping on a Ceramic Capacitor 1965fa 13 LT1965 Series APPLICATIONS INFORMATION recover. Other regulators, such as the LT1083/LT1084/ LT1085 family, also exhibit this phenomenon, so it is not unique to the LT1965. The problem occurs with a heavy output load when the input voltage is high and the output voltage is low. Common situations occur immediately after the removal of a short-circuit or if the shutdown pin is pulled high after the input voltage has already been turned on. The load line for such a load may intersect the output current curve at two points. If this happens, there are two stable output operating points for the regulator. With this double intersection, the input power supply may need to be cycled down to zero and brought up again to make the output recover. Output Voltage Noise The LT1965 regulators are designed to provide low output voltage noise over the 10Hz to 100kHz bandwidth while operating at full load. Output voltage noise is approximately 80nV/Hz over this frequency bandwidth for the LT1965 adjustable version. For higher output voltages (generated by using a resistor divider), the output voltage noise gains up accordingly. Higher values of output voltage noise may be measured if care is not exercised with regard to circuit layout and testing. Crosstalk from nearby traces can induce unwanted noise onto the LT1965's output. Power supply ripple rejection must also be considered; the LT1965 regulators do not have unlimited power supply rejection and will pass a small portion of the input noise through to the output. Thermal Considerations The LT1965's maximum rated junction temperature of 125C limits its power handling capability. Two components comprise the power dissipated by the device: 1. Output current multiplied by the input/output voltage differential: IOUT * (VIN - VOUT), and 2. GND pin current multiplied by the input voltage: IGND * VIN GND pin current is determined using the GND Pin Current curves in the Typical Performance Characteristics section. Power dissipation equals the sum of the two components listed. The LT1965 regulators have internal thermal limiting that protect the device during overload conditions. For continuous normal conditions, do not exceed the maximum junction temperature rating of 125C. Carefully consider all sources of thermal resistance from junction to ambient including other heat sources mounted in proximity to the LT1965. The underside of the LT1965 DFN package has exposed metal (4mm2) from the lead frame to the die attachment. The underside of the LT1965 MSOP package also has exposed metal (3.7mm2). Both packages allow heat to directly transfer from the die junction to the printed circuit board metal to control maximum operating junction temperature. The dual-in-line pin arrangement allows metal to extend beyond the ends of the package on the topside (component side) of a PCB. Connect this metal to GND on the PCB. The multiple IN and OUT pins of the LT1965 also assist in spreading heat to the PCB. For surface mount devices, heat sinking is accomplished by using the heat spreading capabilities of the PC board and its copper traces. Copper board stiffeners and plated through-holes can also be used to spread the heat generated by power devices. 1965fa 14 LT1965 Series APPLICATIONS INFORMATION The following tables list thermal resistance for several different board sizes and copper areas. All measurements were taken in still air on 1/16" FR-4 board with one ounce copper. Table 1. Measured Thermal Resistance for DFN Package Copper Area Topside* Backside 2500mm2 2500mm2 2 1000mm 2500mm2 2 225mm 2500mm2 100mm2 2500mm2 2 50mm 2500mm2 *Device is mounted on topside Board Area Thermal Resistance (Junction-to-Ambient) 2500mm2 2500mm2 2500mm2 2500mm2 2500mm2 60C/W 62C/W 65C/W 68C/W 70C/W 2500mm2 2500mm2 2 1000mm 2500mm2 2 225mm 2500mm2 100mm2 2500mm2 2 50mm 2500mm2 *Device is mounted on topside Example: Given an output voltage of 2.5V, an input voltage range of 3.3V 5%, an output current range of 0mA to 500mA and a maximum ambient temperature of 85C, what will the maximum junction temperature be? The power dissipated by the device equals: IOUT(MAX) * (VIN(MAX) - VOUT) + IGND * VIN(MAX) where: IOUT(MAX) = 500mA VIN(MAX) = 3.465V Table 2. Measured Thermal Resistance for MSOP Package Copper Area Topside* Backside Calculating Junction Temperature Board Area Thermal Resistance (Junction-to-Ambient) 2500mm2 2500mm2 2500mm2 2500mm2 2500mm2 55C/W 57C/W 60C/W 65C/W 68C/W IGND at (IOUT = 500mA, VIN = 3.465V) = 8.2mA So, P = 500mA(3.465V - 2.5V) + 8.2mA(3.465V) = 0.511W Using a DFN package, the thermal resistance will be in the range of 60C/W to 70C/W depending on the copper area. So the junction temperature rise above ambient approximately equals: 0.511W * 65C/W = 33.22C Table 3. Measured Thermal Resistance for DD-PAK Package Copper Area Topside* Backside 2500mm2 2500mm2 1000mm2 2500mm2 125mm2 2500mm2 *Device is mounted on topside Board Area Thermal Resistance (Junction-to-Ambient) 2500mm2 2500mm2 2500mm2 25C/W 30C/W 35C/W The maximum junction temperature equals the maximum ambient temperature plus the maximum junction temperature rise above ambient or: TJMAX = 85C + 33.22C = 118.22C Measured Thermal Resistance for TO-220 Package Thermal Resistance (Junction-to-Case) = 3C/W 1965fa 15 LT1965 Series APPLICATIONS INFORMATION Protection Features The LT1965 regulators incorporate several protection features that makes them ideal for use in battery-powered circuits. In addition to the normal protection features associated with monolithic regulators, such as current limiting and thermal limiting, the devices also protect against reverse input voltages, reverse output voltages and reverse output-to-input voltages. Current limit protection and thermal overload protection protect the device against current overload conditions at its output. For normal operation, do not exceed the maximum rated junction temperature of 125C. The input of the device withstands reverse voltages of 22V. The LT1965 limits current flow to less than 1mA (typically less than 300A) and no negative voltage appears at the output. The device protects both itself and the load against batteries that are plugged in backwards. The LT1965 incurs no damage if its output is pulled below ground. If the input is left open circuit or grounded, the output can be pulled below ground by 22V. For fixed voltage versions, the output will act like a large resistor, typically 5k or higher, limiting current flow to typically less than 300A. For the adjustable version, the output acts like an open circuit and no current flows from the output. However, current flows in (but is limited by) the resistor divider that sets the output voltage. If the input is powered by a voltage source, the output sources current equal to its current limit capability and the LT1965 protects itself by thermal limiting. In this case, grounding the SHDN pin turns off the device and stops the output from sourcing current. The LT1965 adjustable version incurs no damage if the ADJ pin is pulled above or below ground by 9V. If the input is left open circuit or grounded, the ADJ pin performs like an open circuit when pulled below ground and like a large resistor (typically 5k up to 3V on the ADJ pin and then 1.5k up to 9V) in series with a diode when pulled above ground. In situations where the ADJ pin connects to a resistor divider that would pull the ADJ pin above its 9V clamp voltage if the output is pulled high, the ADJ pin input current must be limited to less than 5mA. For example, a resistor divider is used to provide a regulated 1.5V output from the 1.20V reference when the output is forced to 20V. The top resistor of the resistor divider must be chosen to limit the current into the ADJ pin to less than 5mA when the ADJ pin is at 9V. The 11V difference between the OUT and ADJ pins divided by the 5mA maximum current into the ADJ pin yields a minimum top resistor value of 2.2k. In circuits where a backup battery is required, several different input/output conditions can occur. The output voltage may be held up while the input is either pulled to ground, pulled to some intermediate voltage, or is left open circuit. Current flow back into the output follows the curve shown in Figure 6. If the LT1965's IN pin is forced below the OUT pin or the OUT pin is pulled above the IN pin, input current typically drops to less than 2A. This occurs if the LT1965 input is connected to a discharged (low voltage) battery and either a backup battery or a second regulator holds up the output. The state of the SHDN pin has no effect on the reverse output current if the output is pulled above the input. REVERSE OUTPUT CURRENT (mA) 6 TJ = 25C VIN = 0V 5 VOUT = VADJ (LT1965) VOUT = VSENSE (LT195-1.5/-1.8/-2.5/-3.3) 4 CURRENT FLOWS INTO OUTPUT PIN 3 LT1965 LT1965-1.5 LT1965-1.8 2 1 LT1965-2.5 LT1965-3.3 0 0 1 2 3 4 5 6 7 OUTPUT VOLTAGE (V) 9 8 1965 F06 Figure 6. Reverse Output Current 1965fa 16 LT1965 Series TYPICAL APPLICATIONS Paralleling of Regulators for Higher Output Current R1 0.01 + VIN > 3.7V IN OUT + LT1965-3.3 C1 100F SHDN SENSE 3.3V 2.2A C2 22F GND R2 0.01 IN OUT R6 6.65k 1% LT1965 SHDN SHDN ADJ R7 4.02k 1% GND R3 2.2k R4 2.2k 3 2 + 1/2 LT1366 - R5 10k 8 4 1 C3 0.01F 1965 TA03 1965fa 17 LT1965 Series PACKAGE DESCRIPTION DD Package 8-Lead Plastic DFN (3mm x 3mm) (Reference LTC DWG # 05-08-1698) R = 0.115 TYP 5 0.38 0.10 8 0.675 0.05 3.5 0.05 1.65 0.05 2.15 0.05 (2 SIDES) 3.00 0.10 (4 SIDES) PACKAGE OUTLINE 1.65 0.10 (2 SIDES) PIN 1 TOP MARK (NOTE 6) (DD) DFN 1203 0.25 0.05 0.75 0.05 0.200 REF 0.50 BSC 4 0.25 0.05 2.38 0.05 (2 SIDES) 1 0.50 BSC 2.38 0.10 (2 SIDES) 0.00 - 0.05 BOTTOM VIEW--EXPOSED PAD RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS NOTE: 1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-1) 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON TOP AND BOTTOM OF PACKAGE MS8E Package 8-Lead Plastic MSOP (Reference LTC DWG # 05-08-1662) BOTTOM VIEW OF EXPOSED PAD OPTION 0.889 0.127 (.035 .005) 2.794 0.102 (.110 .004) 1 2.06 0.102 (.081 .004) 3.00 0.102 (.118 .004) (NOTE 3) 8 7 6 5 1.83 0.102 (.072 .004) 5.23 (.206) MIN 2.083 0.102 3.20 - 3.45 (.082 .004) (.126 - .136) 0.65 (.0256) BSC 0.42 0.038 (.0165 .0015) TYP 0.254 (.010) 8 1 1.10 (.043) MAX DETAIL "A" DETAIL "A" 0 - 6 TYP 3.00 0.102 (.118 .004) (NOTE 4) 4.90 0.152 (.193 .006) RECOMMENDED SOLDER PAD LAYOUT 0.52 (.0205) REF 2 3 4 0.86 (.034) REF 0.18 (.007) SEATING PLANE GAUGE PLANE 0.53 0.152 (.021 .006) NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 0.22 - 0.38 (.009 - .015) TYP 0.65 (.0256) BSC 0.127 0.076 (.005 .003) MSOP (MS8E) 0603 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX 1965fa 18 LT1965 Series PACKAGE DESCRIPTION Q Package 5-Lead Plastic DD Pak (Reference LTC DWG # 05-08-1461) .256 (6.502) .390 - .415 (9.906 - 10.541) .060 (1.524) .165 - .180 (4.191 - 4.572) .045 - .055 (1.143 - 1.397) 15 TYP .060 (1.524) .060 (1.524) TYP .330 - .370 (8.382 - 9.398) .183 (4.648) +.008 .004 -.004 +0.203 0.102 -0.102 .059 (1.499) TYP ( ) .095 - .115 (2.413 - 2.921) .075 (1.905) .300 (7.620) +.012 .143 -.020 +0.305 3.632 -0.508 ( BOTTOM VIEW OF DD PAK HATCHED AREA IS SOLDER PLATED COPPER HEAT SINK .067 (1.702) .028 - .038 BSC (0.711 - 0.965) TYP ) Q(DD5) 0502 .420 .276 .080 .420 .050 .012 (1.270 0.305) .013 - .023 (0.330 - 0.584) .325 .350 .205 .565 .565 .320 .090 .090 NOTE: 1. DIMENSIONS IN INCH/ (MILLIMETER) 2. DRAWING NOT TO SCALE .042 .067 .042 .067 RECOMMENDED SOLDER PAD LAYOUT FOR THICKER SOLDER PASTE APPLICATIONS RECOMMENDED SOLDER PAD LAYOUT T Package 5-Lead Plastic TO-220 (Standard) (Reference LTC DWG # 05-08-1420) .390 - .415 (9.906 - 10.541) .165 - .180 (4.191 - 4.572) .147 - .155 (3.734 - 3.937) DIA .045 - .055 (1.143 - 1.397) .230 - .270 (5.842 - 6.858) .460 - .500 (11.684 - 12.700) .570 - .620 (14.478 - 15.748) .330 - .370 (8.382 - 9.398) .700 - .728 (17.78 - 18.491) .620 (15.75) TYP .095 - .115 (2.413 - 2.921) SEATING PLANE .260 - .320 (6.60 - 8.13) .152 - .202 (3.861 - 5.131) .155 - .195* (3.937 - 4.953) .013 - .023 (0.330 - 0.584) .067 BSC (1.70) .028 - .038 (0.711 - 0.965) .135 - .165 (3.429 - 4.191) * MEASURED AT THE SEATING PLANE T5 (TO-220) 0801 1965fa Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 19 LT1965 Series TYPICAL APPLICATION Adjustable Current Source R5, 0.01 IN + VIN > 2.7V R1 1k C1 10F R4 2.2k R3 2k R6 2.2k 2 3 NOTE: ADJUST R1 FOR 0A TO 1.1A CONSTANT-CURRENT LOAD + SHDN ADJ GND LT1004-1.2 R2 80.6k LT1965 OUT C2 3.3F R7 470 8 1 1/2 LT1366 + R8 100k C3 1F - C4 10F 1965 TA04 4 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT1129 700mA, Micropower, LDO VIN: 4.2V to 30V, VOUT(MIN) = 3.8V, VDO = 0.40V, IQ = 50A, ISD = 16A; DD, SOT-223, S8, TO220-5 and TSSOP20 Packages LT1761 100mA, Low Noise Micropower, LDO VIN: 1.8V to 20V, VOUT(MIN) = 1.22V, VDO = 0.30V, IQ = 20A, ISD = < 1A, Low Noise < 20VRMS , Stable with 1F Ceramic Capacitors, ThinSOTTM Package LT1762 150mA, Low Noise Micropower, LDO VIN: 1.8V to 20V, VOUT(MIN) = 1.22V, VDO = 0.30V, IQ = 25A, ISD = < 1A, Low Noise < 20VRMS , MS8 Package LT1763 500mA, Low Noise Micropower, LDO VIN: 1.8V to 20V, VOUT(MIN) = 1.22V, VDO = 0.30V, IQ = 30A, ISD = < 1A, Low Noise < 20VRMS , S8 Package LT1764/ LT1764A 3A, Low Noise, Fast Transient Response, LDO VIN: 2.7V to 20V, VOUT(MIN) = 1.21V, VDO = 0.34V, IQ = 1mA, ISD = < 1A, Low Noise < 40VRMS , "A" Version Stable with Ceramic Capacitors, DD and TO220-5 Packages LTC1844 150mA, Very Low Drop-Out LDO VIN: 1.6V to 6.5V, VOUT(MIN) = 1.25V, VDO = 0.08V, IQ = 35A, ISD = < 1A, Low Noise < 60VRMS , ThinSOTTM Package LT1962 300mA, Low Noise Micropower, LDO VIN: 1.8V to 20V, VOUT(MIN) = 1.22V, VDO = 0.27V, IQ = 30A, ISD = < 1A, Low Noise < 20VRMS , MS8 Package LT1963/ LT1963A 1.5A, Low Noise, Fast Transient Response, VIN: 2.1V to 20V, VOUT(MIN) = 1.21V, VDO = 0.34V, IQ = 1mA, ISD = < 1A, Low Noise < 40VRMS , "A" Version Stable with Ceramic Capacitors; LDO DD, TO220-5, SOT-223 and S8 Packages LT3020 100mA, Low Voltage VDO , VIN(MIN) = 0.9V, LDO VIN: 0.9V to 10V, VOUT(MIN) = 0.20V, VDO = 0.15V, IQ = 120A, ISD = 3A, DFN and MS8 Packages LT3021 500mA, Low Voltage VDO , VIN(MIN) = 0.9V, LDO VIN: 0.9V to 10V, VOUT(MIN) = 0.20V, VDO = 0.16V, IQ = 120A, ISD = 3A, DFN and S8 Packages LT3023 Dual, 2x 100mA, Low Noise Micropower, LDO VIN: 1.8V to 20V, VOUT(MIN) = 1.22V, VDO = 0.30V, IQ = 40A, ISD = < 1A, DFN and MS10 Packages LT3024 Dual, 100mA/500mA, Low Noise Micropower, LDO VIN: 1.8V to 20V, VOUT(MIN) = 1.22V, VDO = 0.30V, IQ = 60A, ISD = < 1A, DFN and TSSOP Packages LT3027 Dual, 2x 100mA, Low Noise Micropower, LDO with Independent Inputs VIN: 1.8V to 20V, VOUT(MIN) = 1.22V, VDO = 0.30V, IQ = 25A, ISD = < 1A, Low Noise < 20VRMS , DFN and MS10 Packages LT3028 Dual, 100mA/500mA, Low Noise Micropower, LDO with Independent Inputs VIN: 1.8V to 20V, VOUT(MIN) = 1.22V, VDO = 0.30V, IQ = 30A, ISD = < 1A, Low Noise < 20VRMS , DFN and TSSOP Packages LT3080/ LT3080-1 1.1A Parallelable, Low Noise, Low Dropout 300mV Dropout Voltage (2-Supply Operation), Low Noise: 40VRMS, VIN: 1.2V to 36V, VOUT: 0V to 35.7V, Current-Based Reference with 1-Resistor VOUT Set; Directly Parallelable (No Op Linear Regulator Amp Required), Stable with Ceramic Caps, TO-220, SOT-223, MSOP and 3mm x 3mm DFN Packages; LT3080-1 Version Has Integrated Internal Ballast Resistor ThinSOT is a trademark of Linear Technology Corporation 1965fa 20 Linear Technology Corporation LT 0408 REV A * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com (c) LINEAR TECHNOLOGY CORPORATION 2007