G6K-2F 9DC - OMRON ELECTRONIC COMPONENTS

Low Signal Relay G6K 67

Low Signal Relay

G6K

• Compact fourth generation design, offers excellent board

space savings.

• Available in 2.54 and 3.2 mm coil-contact terminal spacing.

• “-Y” models meet 2.5 kV Bellcore surge requirements.

• Conforms to FCC Part 68.

• Terminal design based on Omron’s successful G6S relay.

• Available in PCB through-hole, SMT gullwing and SMT

“inside-L” terminals.

• UL recognized / CSA certified.

• Available in single coil latching.

• RoHS Compliant.

Ordering Information

To Order: Select the part number and add the desired coil voltage rating (e.g., G6K-2F-DC5).

When ordering tape packing (surface mount versions), add “-TR” to the model number (e.g., G6K-2G-TR-DC5)

Specifications

■Contact Data

Note: This value was measured at a switching frequency of 120 operations/min and the criterion of contact resistance is 50 Ω. This value may vary

depending on the switching frequency and operating environment. Always double-check relay suitability under actual operating conditions.

Terminal Contact form Model

Non-latching

2.54 mm spacing

Non-latching

3.2 mm coil-contact

terminal spacing

Single coil latching

3.2 mm coil-contact

terminal spacing

Gullwing DPDT G6K-2F G6K-2F-Y G6KU-2F-Y

Inside “L” G6K-2G G6K-2G-Y G6KU-2G-Y

PCB through-hole G6K-2P G6K-2P-Y G6KU-2P-Y

Load Resistive load (cosφ=1)

Rated load 0.3 A at 125 VAC

1 A at 30 VDC

Contact material Ag (Au clad)

Max. carry current 1 A

Max. operating voltage 125 VAC, 60 VDC

Max. operating current 1 A

Max. switching capacity 37.5 VA, 30W

Min. permissible load (See note) 10 μA at 10 mVDC

68 Low Signal Relay G6K

■Coil Data

G6K- 2.5 mm coil-contact terminal spacing, standard, non-latching (G6K-2F, G6K-2G, G6K-2P)

G6K- 3.2 mm coil-contact terminal spacing, non-latching (G6K-2F-Y, G6K-2G-Y, G6K-2P-Y)

G6KU- 3.2 mm spacing, single coil latching (G6KU-2F-Y, G6KU-2G-Y, G6KU-2P-Y)

Note: 1. The rated current and coil resistance are measured at a coil temperature of 23°C with a tolerance of ± 10%.

2. The operating characteristics are measured at a coil temperature of 23°C unless otherwise specified.

3. Pick-up voltage will vary with temperature

4. The maximum voltage is the highest voltage that can be imposed on the relay coil instantaneously.

■Characteristics

Note: 1. The contact resistance was measured with 10 mA at 1 VDC with a voltage-drop method.

2. Values in parentheses are typical values unless otherwise stated.

The insulation resistance was measured with a 500-VDC megohmmeter applied to the same parts as those for checking the dielectric strength.

4. Data shown are of initial value.

Rated voltage

(VDC)

Rated current

(mA)

Coil resistance

(Ω)

Pick-up voltage Dropout voltage Maximum voltage Power consumption

(mW)

% of rated value

3 33.0 91 80% max. 10% min. 150% max.

@ 23°C to 70°C

Approx. 100

4.5 23.2 194

5 21.1 237

6 17.6 341

9 11.3 795

12 9.1 1,315

24 4.6 5,220

Rated voltage

(VDC)

Rated current

(mA)

Coil resistance

(Ω)

Set-up voltage Reset voltage Maximum voltage Power consumption

(mW)

% of rated value

3 33.0 91 75% max. 75% min. 150% max.

@ 23°C to 70°C

Approx. 100

4.5 23.2 194

5 21.1 237

6 17.6 341

9 11.3 795

12 9.1 1,315

24 4.6 5,220

Contact resistance (See note 1) 100 mΩ max.

Operate (set) time (See note 2) 3 ms max. (Approx. 1.4 ms - standard. Approx. 1.2 ms - latching)

Release (set) time (See note 2) 3 ms max. (Approx. 1.3 ms - standard. Approx. 1.2 ms - latching)

Insulation resistance (See note 3) 1,000 MΩ min. (at 500 VDC)

Dielectric strength 1,500 VAC for 1 minute between coil contacts

1,000 VAC for 1 minute between contacts of different poles

750 VAC for 1 minute between contacts of the same pole

Surge withstand voltage “-Y’ versions 2,500 V, (2 x 10 μs) between coil and contacts.

(Conforms to Bellcore specifications)

Standard versions 1,500 V, (10 x 160 μs) between coil and contacts / contacts of different and same polarity.

(Conforms to FCC Part 68)

Vibration Mechanical durability 10 to 55 Hz; 5.0 mm double amplitude

Malfunction durability 10 to 55 Hz; 3.3 mm double amplitude

Shock Mechanical durability 1,000 m/s2 (approx. 100G)

Malfunction durability 750 m/s2 (approx. 75G)

Ambient temperature -40°C to 70°C with no icing or condensation

Humidity 5 to 85% RH

Service life Mechanical 50,000,000 operations min. (at 36,000 operations per hour)

Electrical 100,000 operations min. at rated load (at 1,800 operations per hour)

Weight Approx. 0.7 g

Low Signal Relay G6K 69

■Characteristic data

Maximum Switching Capacity Ambient Temperature vs.

Maximum Coil Voltage

Ambient Temperature vs.

Switching Current

Rated operating current (A)

Maximum coil voltage (%)

Rated operating current (A)

DC resistive load

Rated operating voltage (V)Ambient temperature (°C) Ambient temperature (°C)

AC resistive load

Note: The maximum coil voltage refers to the maxi-

mum value in a varying range of operating

power voltage, not a continuous voltage.

Electrical Service Life Ambient Temperature vs. Must

Operate or Must Release Voltage

G6K-2G (F/P), G6K-2G (F/P)-Y

On the basis of rated voltage (%)

Rated operating current (A)

125 VAC resistive load

Ambient temperature: 23°C

Switching frequency:

1,800 operations/hour

Ambient temperature (°C)

Service Life (x10 operations)

30 VDC resistive load

Ambient temperature: 23°C

Switching frequency:

1,800 operations/hour

Max. estimated value

Operate voltage

Release voltage

Ambient Temperature vs. Must

Set or Must Reset Voltage

G6KU-2G (F/P)-Y

On the basis of rated voltage (%)

Ambient temperature (°C)

Max. estimated value

Electrical Service Life

(with Must Operate and Must

Release Voltage) (See note.)

G6K-2G (F/P), G6K-2G (F/P)-Y

Electrical Service Life

(Contact Resistance) (See note.)

G6K-2G (F/P), G6K-2G (F/P)-Y

Contact resistance (mΩ)

Operating frequency (x10 operations)

On the basis of rated voltage (%)

Operating frequency (x103 operations)

Must operate

Must release

Sample: G6K-2G Sample: G6K-2G

Test conditions: 1 A resistive load

contact

Contact resistance

Shock Malfunction

Energized

Not

energized

Shock direction Unit: m/s

Sample: G6K-2G

Number of Relays: 10

Conditions: Shock is applied in ±X, ±Y, and ±Z di

rections three times each with and with

out energizing the Relays to check the

number of contact malfunctions.

Switching frequency: 1,800 operations/h

Number of Relays: 10

Test conditions: 1 A resistive load at

30 VDC with an operation rate of 50%

Number of Relays: 10

at 30 VDC with an operation rate of 50%

Switching frequency: 1,800 operations/h

Note: The tests were conducted at an

ambient temperature of 23°C.

Note: The tests were conducted at an

ambient temperature of 23°C.

70 Low Signal Relay G6K

Note: 1. The tests were conducted at an ambient temperature of 23°C.

2. High-frequency characteristics depend on the PCB to which the Relay is mounted. Always check these characteristics including

endurance in the actual machine before use.

Sample

Not energized

Sample

Energized

Must operate voltage

Must release voltage

Initial stage Test

Average value

Initial stageTest

Average value

Sample

Not energized

Sample

Energized

Initial stageTest

Average value

Initial stageTest

Average value

Change rate on the basis

of initial value (%)

Change rate on the basis

of initial value (%)

Change rate on the basis

of initial value (%)

Change rate on the basis

of initial value (%)

Must operate voltage

Must release voltage

Contact Reliability Test

(See note.)

G6K-2G (F/P), G6K-2G (F/P)-Y

Operating frequency (x10 operations)

Note 1: The test was conducted at an ambient temperature of 23°C.

Sample: G6K-2G

Number of Relays: 10

Test conditions: 10 mA resistive load at

10 mVDC with an operation rate of 50 %

Switching frequency: 7,200 operations/h

Contact resistance (m )

contact

External Magnetic Interference

G6K-2G (F/P), G6K-2G (F/P)-Y

(Average value)

Change rate on the basis of initial value (%)

Sample: G6K-2G

Number of Relays: 10

Must operate voltage

Must release voltage

External magnetic field (A/m)

(Average value)

Change rate on the basis of initial value (%)

Sample: G6K-2G

Number of Relays: 10

Must operate voltage

Must release voltage

External magnetic field (A/m)

(Average value)

Change rate on the basis of initial value (%)

Sample: G6K-2G

Number of Relays: 10

External magnetic field (A/m)

High-frequency Characteristics

(Isolation)

G6K-2G (F/P), G6K-2G (F/P)-Y

(Average value) (Average value)

Insertion loss (dB)

(Average value)

Return loss (dB)

Frequency (MHz) Frequency (MHz)

High-frequency Characteristics

(Insertion Loss)

G6K-2G (F/P), G6K-2G (F/P)-Y

High-frequency Characteristics

(Return Loss)

G6K-2G (F/P),G6K-2G (F/P)-Y

Mutual Magnetic Interference

G6K-2G (F/P), G6K-2G (F/P)-Y

Mutual Magnetic Interference

G6K-2G (F/P), G6K-2G (F/P)-Y

Must operate voltage

Must release voltage

Isolation (dB)

Frequency (MHz)

2: The contact resistance data are periodically measured reference values and are not values from each monitoring operation.

Contact resistance values will vary according to the switching frequency and operating environment, so be sure to check

operation under the actual operating conditions before use.

Sample: G6K-2G

Number of Relays: 10

0.1

0.2

0.3

0.4

0.5

1 10 100

Sample: G6K-2G

Number of Relays: 10

1 10 100

Sample: G6K-2G

Number of Relays: 10

Return loss

V.SWR

100

1.4

1.35

1.3

1.25

1.2

1.15

1.1

1.05

V. S W R

1 10 100

Low Signal Relay G6K 71

■Approvals

UL Recognized (File No. E41515) / CSA Certified (File No. LR31928) - - Ambient Temp. = 40°C

Dimensions

Note: All units are in millimeters unless otherwise indicated.

Contact form Coil rating Contact ratings Number of test operations

DPDT 3 to 24 VDC 1 A at 30 VDC (Resistive)

0.5 A at 60 VDC (Resistive)

0.3 A at 125 VAC (General Use)

6,000

Must Operate and Must Release

Time Distribution

(See note.)

G6K-2G (F/P), G6K-2G (F/P)-Y

Number of contacts

Sample: G6K-2G

Number of Relays:

Time (ms)

Sample: G6K-2G

Number of Relays: 50

Change rate on the basis of rated value (%)

After test

Must Operate and Must Release

Bounce Time Distribution (See note.)

G6K-2G (F/P) , G6K-2G (F/P)-Y

Vibration Resistance

G6K-2G (F/P), G6K-2G (F/P)-Y

Number of contacts

Note: The tests were conducted at an ambient temperature of 23°C.

Must operate

bounce time

Must operate voltage

Must release voltage

Time (ms)

Must release

bounce time

Must operate

Must release time

G6K-2F Mounting Dimensions (Top View) Terminal Arrangement/

Internal Connections

(Top View)

Orientation mark

Note: Each value has a tolerance of ±0.3 mm.

Tolerance: ±0.1 mm

G6K-2G Mounting Dimensions (Top View) Terminal Arrangement/

Internal Connections

(Top View)

Orientation mark

Note: Each value has a tolerance of ±0.3 mm.

Tolerance: ±0.1 mm

G6K-2P Mounting Dimensions (Bottom View) Terminal Arrangement/

Internal Connections

(Bottom View)

Orientation mark

Note: Each value has a tolerance of ±0.3 mm.

Eight, 0.8-dia. holes

Tolerance: ±0.1 mm

72 Low Signal Relay G6K

G6K-2F-Y

Mounting Dimensions (Top View) Terminal Arrangement/

Internal Connections

(Top View)

Orientation mark

Note: Each value has a tolerance of ±0.3 mm.

Tolerance: ±0.1 mm

G6K-2G-Y

Mounting Dimensions (Top View) Terminal Arrangement/

Internal Connections

(Top View)

Orientation mark

Tolerance: ±0.1 mm

Note: Each value has a tolerance of ±0.3 mm.

G6K-2P-Y

Mounting Dimensions (Bottom View) Terminal Arrangement/

Internal Connections

(Bottom View)

Orientation mark

Note: Each value has a tolerance of ±0.3 mm.

Eight,

0.8-dia. holes

Tolerance: ±0.1 mm

G6KU-2F-Y

Mounting Dimensions (Top View) Terminal Arrangement/

Internal Connections

(Top View)

Orientation mark

Note: Each value has a tolerance of ±0.3 mm.

Tolerance: ±0.1 mm

G6KU-2G-Y

Mounting Dimensions (Top View) Terminal Arrangement/

Internal Connections

(Top View)

Orientation mark

Note: Each value has a tolerance of ±0.3 mm.

Tolerance: ±0.1 mm

G6KU-2P-Y

Mounting Dimensions (Bottom View) Terminal Arrangement/

Internal Connections

(Bottom View)

Orientation mark

Note: Each value has a tolerance of ±0.3 mm.

Eight, 0.8-dia. holes

Tolerance: ±0.1 mm

Low Signal Relay G6K 73

■Packaging Information

Relays in tube packing are arranged so that the orientation mark of each Relay is on the left side.

Be sure to reference Relay orientation when mounting the Relay to the PCB.

Tube length: 520 mm (stopper not included)

No. of Relays per Tube: 50

■Tape and Reel Dimensions (Surface Mount Models)

•Tape type: ETX7200 (EIAJ - Electronic Industrial Association of Japan)

•Reel type: RPM-16D (EIAJ, 330 mm diameter)

•Relays per reel: 900

Tube packing Standard nomenclature 50 pcs per anti-static tube

Tape packing

(SMT versions, only)

When ordering, add “TR” before the rated coil voltage (e.g., G6K-2G-TR-DC5).

Note: TR is not part of the relay model number and will not be marked on the relay.

900 pcs per reel

2 reels per box

Order in box multiples

(see details below)

Stopper (gray) Orientation of Relays

Stopper (green)

1. Direction of Relay Insertion

2. Reel Dimensions

3. Carrier Tape Dimensions

Top tape

(cover tape)

Carrier tape

Orientation mark

Pulling

direction

G6K-2F, G6K-2F-Y, G6KU-2F-Y

G6K-2G, G6K-2G-Y, G6KU-2G-Y

Emboss

tape

74 Low Signal Relay G6K

■Recommended Soldering Method

Temperature indicates the surface temperature of the PCBs.

IRS Method (for surface mounting terminal models)

(1) IRS Method (Mounting Solder: Lead) (2) IRS Method (Mounting Solder: Lead-free)

•The thickness of cream solder to be applied should be within a range between 150 and 200 μm on OMRON’s recommended PCB pattern.

•In order to perform correct soldering, it is recommended that the correct soldering conditions be maintained as shown below on the left side.

Visually check that the Relay is properly soldered.

Precautions

■Correct Use

Handling

Do not unpack the relay until mounting it.

Soldering

Solder: JIS Z3282, H63A or equivalent

Soldering temperature: Approx. 250°C (260°C if the DWS method is

used)

Soldering time: Approx. 5 s max. (approx. 2 s for the first time and

approx. 3 s for the second time if the DWS method is used)

Be sure to make a molten solder level adjustment so that the solder

will not overflow on the PCB.

Claw Securing Force During Automatic

Mounting

During automatic insertion of Relays, make sure to set the securing

force of each claw to the following so that the Relays characteristics

will be maintained.

Environmental Conditions During Operation,

Storage, and Transportation

It is best to keep the relay in its packaging in a controlled environ-

ment until it is ready for mounting.

If the Relay is stored for a long time in an adverse environment with

high temperature, high humidity, organic gases, or sulfide gases, sul-

fide or oxide films will form on the contact surfaces. These films may

result in unstable contact, contact problems, or functional problems.

Therefore, operate, store, or transport the product under specified

environmental conditions.

Latching Relay Mounting

Make sure that the vibration or shock that is generated from other

devices, such as relays in operation, on the same panel and imposed

on the Latching Relay does not exceed the rated value, otherwise the

Latching Relay that has been set may be reset or vice versa. The

Latching Relay is reset before shipping. If excessive vibration or

shock is imposed, however, the Latching Relay may be set acciden-

tally. Be sure to apply a reset signal before use.

Maximum Allowable Voltage

The maximum allowable voltage of the coil can be obtained from the

coil temperature increase and the heat-resisting temperature of coil

insulating sheath material. (Exceeding the heat-resisting tempera-

ture may result in burning or short-circuiting.) The maximum allow-

able voltage also involves important restrictions which include the

following:

Temperature (°C)

Soldering

Preheating

Time (s)

220 to

245

180 to

200

150

90 to 120 20 to 30

Temperature (°C)

Soldering

Preheating

Time (s)

Upper surface of case (peak):

255˚C max.

120 max. 30 max.

250 max.

230

180

150

Note: The temperature profile indicates the

temperature of the relay terminal

section.

Relay

terminal

section

Correct Soldering Incorrect Soldering

PCB

Terminal

Solder

Relay

Land

Excessive

amount of

solder

Insufficient

amount of

solder

Direction A: 1.96 N

Direction B: 4.90 N

Direction C: 1.96 N

Low Signal Relay G6K 75

•Must not cause thermal changes in or deterioration of the insulating

material.

•Must not cause damage to other control devices.

•Must not cause any harmful effect on people.

•Must not cause fire.

Therefore, be sure to use the maximum allowable voltage as speci-

fied in the catalog.

As a rule, the rated voltage must be applied to the coil. A voltage

exceeding the rated value, however, can be applied to the coil pro-

vided that the voltage is less than or equal to the maximum allowable

voltage. It must be noted that continuous voltage application to the

coil will cause a coil temperature increase which may affect charac-

teristics such as electrical life and coil insulation.

Coating

The Relay mounting on the PCB may be coated or washed but do not

apply silicone coating or detergent containing silicone, otherwise the

silicone coating or detergent may remain on the surface of the Relay.

PCB Mounting

If two or more Relays are closely mounted with the long sides of the

Relays facing each other and soldering is performed with infrared

radiation, the solder may not be properly exposed to the infrared

rays. Be sure to keep the proper distance between adjacent Relays

as shown below to insure formation of good solder joints.

Two or more Relays may be mounted as closely as desired with the

short sides of the Relays facing each other.

G6K-2G

G6K-2F

2 mm min.

2.7 mm min.

76 Low Signal Relay G6K

MEMO

Low Signal Relay G6K

Omron Electronic Components, LLC

Terms and Conditions of Sales

1. Definitions: The words used herein are defined as follows.

(a) Terms: These terms and conditions

(b) Seller: Omron Electronic Components LLC and its subsidiaries

(d) Products: Products and/or services of Seller

(e) Including: Including without limitation

2. Offer; Acceptance: These Terms are deemed part of all quotations, acknowledgments,

invoices, purchase orders and other documents, whether electronic or in writing, relating

to the sale of Products by Seller. Seller hereby objects to any Terms proposed in Buyer's

purchase order or other documents which are inconsistent with, or in addition to, these

Ter ms .

3. Distributor: Any distributor shall inform its customer of the contents after and including

section III of these Terms.

1. Prices; Payment: All prices stated are current, subject to change without notice by Seller.

Buyer agrees to pay the price in effect at the time the purchase order is accepted by

Seller. Payments for Products received are due net 30 days unless otherwise stated in

the invoice. Buyer shall have no right to set off any amounts against the amount owing in

respect of this invoice.

2. Discounts: Cash discounts, if any, will apply only on the net amount of invoices sent to

Buyer after deducting transportation charges, taxes and duties, and will be allowed only

if (a) the invoice is paid according to Seller's payment terms and (b) Buyer has no past

due amounts owing to Seller.

3. Interest: Seller, at its option, may charge Buyer 1.5% interest per month or the maximum

legal rate, whichever is less, on any balance not paid within the stated terms.

4. Orders: Seller will accept no order less than 200 U.S. dollars net billing.

5. Currencies: If the prices quoted herein are in a currency other than U.S. dollars, Buyer

shall make remittance to Seller at the then current exchange rate most favorable to

Seller; provided that if remittance is not made when due, Buyer will convert the amount

to U.S. dollars at the then current exchange rate most favorable to Seller available

during the period between the due date and the date remittance is actually made.

6. Governmental Approvals: Buyer shall be responsible for all costs involved in obtaining

any government approvals regarding the importation or sale of the Products.

7. Taxes: All taxes, duties and other governmental charges (other than general real

property and income taxes), including any interest or penalties thereon, imposed directly

or indirectly on Seller or required to be collected directly or indirectly by Seller for the

manufacture, production, sale, delivery, importation, consumption or use of the Products

sold hereunder (including customs duties and sales, excise, use, turnover and license

taxes) shall be charged to and remitted by Buyer to Seller.

8. Financial: If the financial position of Buyer at any time becomes unsatisfactory to Seller,

Seller reserves the right to stop shipments or require satisfactory security or payment in

advance. If Buyer fails to make payment or otherwise comply with these Terms or any

related agreement, Seller may (without liability and in addition to other remedies) cancel

any unshipped portion of Products sold hereunder and stop any Products in transit until

Buyer pays all amounts, including amounts payable hereunder, whether or not then due,

which are owing to it by Buyer. Buyer shall in any event remain liable for all unpaid

accounts.

9. Cancellation; Etc: Orders are not subject to rescheduling or cancellation unless Buyer

indemnifies Seller fully against all costs or expenses arising in connection therewith.

10. Force Majeure: Seller shall not be liable for any delay or failure in delivery resulting from

causes beyond its control, including earthquakes, fires, floods, strikes or other labor

disputes, shortage of labor or materials, accidents to machinery, acts of sabotage, riots,

delay in or lack of transportation or the requirements of any government authority.

11. Shipping; Delivery: Unless otherwise expressly agreed in writing by Seller:

(a) All sales and shipments of Products shall be FOB shipping point (unless otherwise

stated in writing by Seller), at which point title to and all risk of loss of the Products

shall pass from Seller to Buyer, provided that Seller shall retain a security interest in

the Products until the full purchase price is paid by Buyer;

(b) Delivery and shipping dates are estimates only; and

handling and extra charges apply to special conditions.

12. Claims: Any claim by Buyer against Seller for shortage or damage to the Products

occurring before delivery to the carrier or any claim related to pricing or other charges

must be presented in detail in writing to Seller within 30 days of receipt of shipment.

1. Suitability: IT IS THE BUYER’S SOLE RESPOINSIBILITY TO ENSURE THAT ANY

OMRON PRODUCT IS FIT AND SUFFICIENT FOR USE IN A MOTORIZED VEHICLE

APPLICATION. BUYER SHALL BE SOLELY RESPONSIBLE FOR DETERMINING

APPROPRIATENESS OF THE PARTICULAR PRODUCT WITH RESPECT TO THE

BUYER’S APPLICATION INCLUDING (A) ELECTRICAL OR ELECTRONIC

COMPONENTS, (B) CIRCUITS, (C) SYSTEM ASSEMBLIES, (D) END PRODUCT, (E)

SYSTEM, (F) MATERIALS OR SUBSTANCES OR (G) OPERATING ENVIRONMENT.

Buyer acknowledges that it alone has determined that the Products will meet their

requirements of the intended use in all cases. Buyer must know and observe all

prohibitions of use applicable to the Product/s.

2. Use with Attention: The followings are some examples of applications for which

particular attention must be given. This is not intended to be an exhaustive list of all

possible use of any Product, nor to imply that any use listed may be suitable for any

Product:

(a) Outdoor use, use involving potential chemical contamination or electrical

interference.

(b) Use in consumer Products or any use in significant quantities.

medical equipment, amusement machines, vehicles, safety equipment, and

installations subject to separate industry or government regulations.

(d) Systems, machines, and equipment that could present a risk to life or property.

3. Prohibited Use: NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING

SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM

AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE

PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE

WITHIN THE OVERALL EQUIPMENT OR SYSTEM.

4. Motorized Vehicle Application: USE OF ANY PRODUCT/S FOR A MOTORIZED

VEHICLE APPLICATION MUST BE EXPRESSLY STATED IN THE SPECIFICATION BY

SELLER.

5. Programmable Products: Seller shall not be responsible for the Buyer's programming of

a programmable Product.

1. Warranty: Seller's exclusive warranty is that the Products will be free from defects in

materials and workmanship for a period of twelve months from the date of sale by Seller

(or such other period expressed in writing by Seller). SELLER MAKES NO WARRANTY

OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT ALL OTHER WARRANTIES,

NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE OF THE PRODUCTS.

2. Buyer Remedy: Seller's sole obligation hereunder shall be to replace (in the form

originally shipped with Buyer responsible for labor charges for removal or replacement

thereof) the non-complying Product or, at Seller's election, to repay or credit Buyer an

amount equal to the purchase price of the Product; provided that there shall be no

liability for Seller or its affiliates unless Seller's analysis confirms that the Products were

correctly handled, stored, installed and maintained and not subject to contamination,

abuse, misuse or inappropriate modification. Return of any Products by Buyer must be

approved in writing by Seller before shipment.

3. Limitation on Liability: SELLER AND ITS AFFILIATES SHALL NOT BE LIABLE FOR

SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF

PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED

WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT,

WARRANTY, NEGLIGENCE OR STRICT LIABILITY. FURTHER, IN NO EVENT SHALL

LIABILITY OF SELLER OR ITS AFFILITATES EXCEED THE INDIVIDUAL PRICE OF

THE PRODUCT ON WHICH LIABILITY IS ASSERTED.

4. Indemnities: Buyer shall indemnify and hold harmless Seller, its affiliates and its

employees from and against all liabilities, losses, claims, costs and expenses (including

attorney's fees and expenses) related to any claim, investigation, litigation or proceeding

(whether or not Seller is a party) which arises or is alleged to arise from Buyer's acts or

omissions under these Terms or in any way with respect to the Products.

1. Intellectual Property: The intellectual property embodied in the Products is the exclusive

property of Seller and its affiliates and Buyer shall not attempt to duplicate it in any way

without the written permission of Seller. Buyer (at its own expense) shall indemnify and

hold harmless Seller and defend or settle any action brought against Seller to the extent

that it is based on a claim that any Product made to Buyer specifications infringed

intellectual property rights of another party.

2. Property; Confidentiality: Notwithstanding any charges to Buyer for engineering or

tooling, all engineering and tooling shall remain the exclusive property of Seller. All

information and materials supplied by Seller to Buyer relating to the Products are

confidential and proprietary, and Buyer shall limit distribution thereof to its trusted

employees and strictly prevent disclosure to any third party.

3. Performance Data: Performance data is provided as a guide in determining suitability

and does not constitute a warranty. It may represent the result of Seller's test conditions,

and the users must correlate it to actual application requirements.

4. Change In Specifications: Product specifications and descriptions may be changed at

any time based on improvements or other reasons. It is Seller’s practice to change part

numbers when published ratings or features are changed, or when significant

engineering changes are made. However, some specifications of the Product may be

changed without any notice.

5. Errors And Omissions: The information on Seller’s website or in other documentation

has been carefully checked and is believed to be accurate; however, no responsibility is

assumed for clerical, typographical or proofreading errors or omissions.

6. Export Controls: Buyer shall comply with all applicable laws, regulations and licenses

regarding (a) export of the Products or information provided by Seller; (b) sale of

Products to forbidden or other proscribed persons or organizations; (c) disclosure to non-

citizens of regulated technology or information.

1. Waiver: No failure or delay by Seller in exercising any right and no course of dealing

between Buyer and Seller shall operate as a waiver of rights by Seller.

2. Assignment: Buyer may not assign its rights hereunder without Seller's written consent.

3. Law: These Terms are governed by Illinois law (without regard to conflict of laws).

Federal and state courts in Cook County, Illinois have exclusive jurisdiction for any

dispute hereunder.

4. Amendment: These Terms constitute the entire agreement between Buyer and Seller

relating to the Products, and no provision may be changed or waived unless in writing

signed by the parties.

5. Severability: If any provision hereof is rendered ineffective or invalid, such provision shall

not invalidate any other provision.

I. GENERAL

II. SALES

III. PRECAUTIONS

IV. WARRANTY AND LIMITATION

V. INFORMATION; ETC.

VI. MISCELLANEOUS

Low Signal Relay G6K

Certain Precautions on Specifications and Use

1. Suitability for Use. Seller shall not be responsible for conformity with any stan-

dards, codes or regulations which apply to the combination of the Product in

Buyer's application or use of the Product. At Buyer's request, Seller will pro-

vide applicable third party certification documents identifying ratings and limi-

tations of use which apply to the Product. This information by itself is not

sufficient for a complete determination of the suitability of the Product in com-

bination with the end product, machine, system, or other application or use.

Buyer shall be solely responsible for determining appropriateness of the par-

ticular Product with respect to Buyer's application, product or system. Buyer

shall take application responsibility in all cases but the following is a non-

exhaustive list of applications for which particular attention must be given:

(i) Outdoor use, uses involving potential chemical contamination or electrical

interference, or conditions or uses not described in this document.

(ii) Energy control systems, combustion systems, railroad systems, aviation

systems, medical equipment, amusement machines, vehicles, safety

equipment, and installations subject to separate industry or government

regulations.

(iii) Use in consumer products or any use in significant quantities.

(iv) Systems, machines and equipment that could present a risk to life or

property. Please know and observe all prohibitions of use applicable to this

product.

NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS

RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM

AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT

THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE

INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.

2. Programmable Products. Seller shall not be responsible for the user's pro-

gramming of a programmable product, or any consequence thereof.

3. Performance Data. Performance data given in this publication is provided as

a guide for the user in determining suitability and does not constitute a war-

ranty. It may represent the result of Seller's test conditions, and the users must

correlate it to actual application requirements. Actual performance is subject to

Seller's Warranty and Limitations of Liability.

4. Change in Specifications. Product specifications and accessories may be

changed at any time based on improvements and other reasons. It is our prac-

tice to change part numbers when published ratings or features are changed,

or when significant construction changes are made. However, some specifica-

tions of the Product may be changed without any notice. When in doubt, spe-

cial part numbers may be assigned to fix or establish key specifications for

your application. Please consult with your Seller representative at any time to

confirm actual specifications of purchased Product.

5. Errors and Omissions. The information in this publication has been carefully

checked and is believed to be accurate; however, no responsibility is assumed

for clerical, typographical or proofreading errors, or omissions.

6. RoHS Compliance. Where indicated, our products currently comply, to the

best of our knowledge as of the date of this publication, with the requirements

of the European Union's Directive on the Restriction of certain Hazardous

Substances ("RoHS"), although the requirements of RoHS do not take effect

until July 2006. These requirements may be subject to change. Please consult

our website for current information.

OMRON ON-LINE

Global - http://www.omron.com

USA - http://www.components.omron.com

Cat. No. X301-E-1 Printed in USA

OMRON ELECTRONIC

COMPONENTS LLC

55 E. Commerce Drive, Suite B

Schaumburg, IL 60173

847-882-2288

06/09 Specifications subject to change without notice

Complete “Terms and Conditions of Sale” for product purchase and use are on Omron’s website

at http://www.components.omron.com – under the “About Us” tab, in the Legal Matters section.

ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.

To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.