Transient Voltage Suppression Diodes Axial Leaded - 1500W > TP1.5KE series TP1.5KE Series RoHS Pb e3 Description The TP1.5KE Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Uni-directional Features Bi-directional Agency Approvals AGENCY AGENCY FILE NUMBER E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Symbol Value Unit PPPM 1500 W PD 6.5 W IFSM 200 A VF 3.5 V TJ -55 to 150 C Storage Temperature Range TSTG -55 to 175 C Typical Thermal Resistance Junction to Lead RJL 15 C/W Typical Thermal Resistance Junction to Ambient RJA 75 C/W Peak Pulse Power Dissipation by 10/1000s Test Waveform (Fig.2) (Note 1) Steady State Power Dissipation on Infinite Heat Sink at TL=75C Peak Forward Surge Current, 8.3ms Single Half Sine Wave Unidirectional Only (Note 2) Maximum Instantaneous Forward Voltage at 100A for Unidirectional Only (Note 3) Operating Junction Temperature Range * Hi reliability application and automotive grade AEC-Q101 rev D qualified * Glass passivated chip junction in DO-201 Package * 1500W peak pulse capability at 10/1000s waveform, repetition rate (duty cycles):0.01% * Fast response time: typically less than 1.0ps from 0 Volts to BV min * Excellent clamping capability * Typical failure mode is short from over-specified voltage or current * Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c * IEC-61000-4-2 ESD 30kV(Air), 30kV (Contact) * ESD protection of data lines in accordance with IEC 61000-4-2 * EFT protection of data lines in accordance with IEC 61000-4-4 * Low incremental surge resistance * High temperature to reflow soldering guaranteed: 260C/10sec / 0.375",(9.5mm) lead length, 5 lbs., (2.3kg) tension * VBR @ TJ= VBR@25C x (1+T x (TJ - 25)) (T:Temperature Coefficient, typical value is 0.1%) * Plastic package is flammability rated V-0 per Underwriters Laboratories * Matte tin lead-free plated * Halogen free and RoHS compliant * Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/JEDEC J-STD609A.01) Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above TJ (initial) =25OC per Fig. 3. Applications 2. Measured on 8.3ms single half sine wave or equivalent square wave, duty cycle=4 per minute maximum. TVS devices are ideal for the protection of I/O interfaces, VCC bus and other vulnerable circuits used in telecom, computer, industrial and consumer electronic applications. Functional Diagram Bi-directional Cathode Anode Uni-directional (c)2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/25/16 Transient Voltage Suppression Diodes Axial Leaded - 1500W > TP1.5KE series Electrical Characteristics (T =25C unless otherwise noted) A Part Number (Uni) Part Number (Bi) Reverse Stand off Voltage VR (Volts) TP1.5KE12A TP1.5KE13A TP1.5KE15A TP1.5KE16A TP1.5KE18A TP1.5KE20A TP1.5KE22A TP1.5KE24A TP1.5KE27A TP1.5KE30A TP1.5KE33A TP1.5KE36A TP1.5KE39A TP1.5KE43A TP1.5KE47A TP1.5KE12CA TP1.5KE13CA TP1.5KE15CA TP1.5KE16CA TP1.5KE18CA TP1.5KE20CA TP1.5KE22CA TP1.5KE24CA TP1.5KE27CA TP1.5KE30CA TP1.5KE33CA TP1.5KE36CA TP1.5KE39CA TP1.5KE43CA TP1.5KE47CA 10.20 11.10 12.80 13.60 15.30 17.10 18.80 20.50 23.10 25.60 28.20 30.80 33.30 36.80 40.20 Breakdown Voltage VBR (Volts) @ IT MIN MAX 11.40 12.40 14.30 15.20 17.10 19.00 20.90 22.80 25.70 28.50 31.40 34.20 37.10 40.90 44.70 12.60 13.70 15.80 16.80 18.90 21.00 23.10 25.20 28.40 31.50 34.70 37.80 41.00 45.20 49.40 Test Current IT (mA) Maximum Clamping Voltage VC @ Ipp (Volts) Maximum Peak Pulse Current Ipp (A) Maximum Reverse Leakage IR @ VR (A) Agency Approval 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 16.7 18.2 21.2 22.5 25.2 27.7 30.6 33.2 37.5 41.4 45.7 49.9 53.9 59.3 64.8 91.0 83.5 71.7 67.6 60.3 54.9 49.7 45.8 40.5 36.7 33.3 30.5 28.2 25.6 23.5 5 1 1 1 1 1 1 1 1 1 1 1 1 1 1 X X X X X X X X X X X X X X X I-V Curve Characteristics Bi-directional Uni-directional Ipp Vc VBR VR IR VF IT V Vc VBR VR IT IR Ipp PPPM VR VBR VC IR VF IR IT VR VBR Vc V Ipp Peak Pulse Power Dissipation -- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the TVS at a specified Ippm (peak impulse current) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional (c)2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/25/16 Transient Voltage Suppression Diodes Axial Leaded - 1500W > TP1.5KE series Ratings and Characteristic Curves (T =25C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating 100 PPPM-Peak Pulse Power (kW) Voltage Transients Voltage or Current Voltage Across TVS Current Through TVS TJ initial = Tamb 10 1 0.1 0.001 0.01 IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % 150 100 75 50 25 0 25 50 75 100 125 150 tr=10sec Half Value IPPM IPPM ( ) 2 50 0 175 TJ=25C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM Peak Value IPPM 100 10/1000sec. Waveform as defined by R.E.A td 1.0 0 2.0 3.0 4.0 t-Time (ms) TJ - Initial Junction Temperature (C) Figure 5 - Typical Junction Capacitance Figure 6 - Typical Transient Thermal Impedance 100 Transient Thermal Impedance (C/W) 100000 Uni-directional V=0V 10000 Bi-directional V=0V Cj(pF) 10 Figure 4 - Pulse Waveform Figure 3 - Peak Pulse Power Derating Curve 1000 Uni-directional V=VR 100 Bi-directional V=VR 10 1 1 td-Pulse Width (ms) Time 0 0.1 1 10 100 VBR - Reverse Breakdown Voltage(V) 1000 10 1 0.1 0.01 0.1 1 10 100 1000 TP - Pulse Duration (s) (c)2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/25/16 Transient Voltage Suppression Diodes Axial Leaded - 1500W > TP1.5KE series Ratings and Characteristic Curves (T =25C unless otherwise noted) (Continued) A Figure 8 - Peak Forward Voltage Drop vs Peak Forward Current (Typical Values) 100.0 200 180 IF- Peak Forward Current(A) IFSM - Peak Forward Surge Current (A) Figure 7 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional Only 160 140 120 100 80 60 40 10.0 1.0 20 0 1 10 0.1 100 0.0 1.0 2.0 3.0 Number of Cycles at 60 Hz 4.0 5.0 6.0 7.0 8.0 9.0 VF-Peak Forward Voltage(V) Soldering Parameters Pre Heat Lead-free assembly - Temperature Min (Ts(min)) 150C - Temperature Max (Ts(max)) 200C - Time (min to max) (ts) 60 - 180 secs Average ramp up rate (Liquidus Temp (TA) to peak 3C/second max TS(max) to TA - Ramp-up Rate 3C/second max Reflow - Temperature (TA) (Liquidus) 217C - Time (min to max) (ts) 60 - 150 seconds tp TP Ramp-up TL Temperature (T) Reflow Condition tL Ts(max) Ts(min) Ramp-down ts Preheat 25C t 25C to Peak Time (t) Peak Temperature (TP) 260+0/-5 C Time within 5C of actual peak Temperature (tp) 20 - 40 seconds Flow/Wave Soldering (Solder Dipping) Ramp-down Rate 6C/second max Peak Temperature : 265OC Time 25C to peak Temperature (TP) 8 minutes Max. Dipping Time : 10 seconds Do not exceed 260C Soldering : 1 time Physical Specifications Critical Zone TL to TP Environmental Specifications Weight 0.045oz., 1.2g High Temp. Storage JESD22-A103 Case JEDEC DO-201 molded plastic body over passivated junction. HTRB JESD22-A108 Polarity Color band denotes the cathode except Bipolar. Temperature Cycling JESD22-A104 Terminal Matte Tin axial leads, solderable per JESD22-B102. H3TRB JESD22-A101 RSH JESD22-B106 (c)2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/25/16 Transient Voltage Suppression Diodes Axial Leaded - 1500W > TP1.5KE series Dimensions D Dimensions Cathode Band (for Uni-directional products only) C A A B Part Numbering System Inches Millimeters Min Max Min Max A 1.000 - 25.40 - B 0.285 0.375 7.20 9.50 C 0.038 0.042 0.96 1.07 D 0.190 0.210 4.80 5.30 Part Marking System Cathode Band TYPE CODE: A Uni-Directional (5% VBR Voltage Tolerance) CA Bi-Directional (5% VBR Voltage Tolerance) (for Uni-directional products only) F TP1.5KE xxx XX YYWW Trace Code Marking Littelfuse Logo VBR VOLTAGE CODE (Refer to the Electrical Characteristics table) TP1.5KEXXX SERIES CODE YY:Year Code WW: Week Code Product Type Packaging Part Number Component Package Quantity Packaging Option TP1.5KExxxXX DO-201 1200 Tape & Reel Packaging Specification EIA STD RS-296 Tape and Reel Specification Off Center either side 2.063+0.079/-0.039 (53.0+2.0/-1.0) 0.028(0.7) 2.56 (65.0) 0.047 (1.2) 0.394+/-0.020 (10.0+/-0.5) 13.0 (330.2) 0.236 (6.0) Dimensions are in inches/mm 3.0 (76.2) 0.68 (17.27) 2.75 (69.85) Recess Depth Max. 0.75 (19.05) Direction of Feed (c)2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/25/16