FN3283 Rev 8.00 Page 1 of 17
Jun 13, 2006
FN3283
Rev 8.00
Jun 13, 2006
DG408, DG409
Single 8-Channel/Differential 4-Channel, CMOS Analog Multiplexers
DATASHEET
The DG408 Single 8-Channel, and DG409 Differential
4-Channel monolithic CMOS analog multiplexers are drop-in
replacements for the popular DG508A and DG509A series
devices. They each include an array of eight analog
switches, a TTL/CMOS compatible digital decode circuit for
channel selection, a voltage reference for logic thresholds
and an ENABLE input for device selection when several
multiplexers are present.
The DG408 and DG409 feature lower signal ON resistance
(<100) and faster switch transition time (tTRANS < 250ns)
compared to the DG508A or DG509A. Charge injection has
been reduced, simplifying sample and hold applications. The
improvements in the DG408 series are made possible by
using a high-voltage silicon-gate process. An epitaxial layer
prevents the latch-up associated with older CMOS
technologies. Power supplies may be single-ended from +5V
to +34V, or split from 5V to 20V.
The analog switches are bilateral, equally matched for AC or
bidirectional signals. The ON resistance variation with
analog signals is quite low over a 5V analog input range.
Features
ON Resistance (Max, 25°C). . . . . . . . . . . . . . . . . . . 100
Low Power Consumption (PD) . . . . . . . . . . . . . . .<11mW
Fast Switching Action
-t
TRANS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <250ns
-t
ON/OFF(EN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . <150ns
Low Charge Injection
Upgrade from DG508A/DG509A
TTL, CMOS Compatible
Single or Split Supply Operation
Pb-Free Plus Anneal Available (RoHS Compliant)
Applications
Data Acquisition Systems
Audio Switching Systems
Automatic Testers
Hi-Rel Systems
Sample and Hold Circuits
Communication Systems
Analog Selector Switch
Ordering Information
PART
NUMBER
PART
MARKING
TEMP.
RANGE (°C) PACKAGE
PKG.
DWG. #
DG408DJ DG408DJ -40 to 85 16 Ld PDIP E16.3
DG408DJZ (Note) DG408DJZ -40 to 85 16 Ld PDIP** (Pb-free) E16.3
DG408DY* DG408DY -40 to 85 16 Ld SOIC M16.15
DG408DYZ* (Note) DG408DYZ -40 to 85 16 Ld SOIC (Pb-free) M16.15
DG408DVZ* (Note) DG408DVZ -40 to 85 16 Ld TSSOP (Pb-free) M16.173
DG409DJ DG409DJ -40 to 85 16 Ld PDIP E16.3
DG409DJZ (Note) DG409DJZ -40 to 85 16 Ld PDIP** (Pb-free) E16.3
DG409DY* DG409DY -40 to 85 16 Ld SOIC M16.15
DG409DYZ* (Note) DG409DYZ -40 to 85 16 Ld SOIC (Pb-free) M16.15
DG409DVZ* (Note) DG409DVZ -40 to 85 16 Ld TSSOP (Pb-free) M16.173
*Add “-T” suffix for tape and reel.
**Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications.
NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate
termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
FN3283 Rev 8.00 Page 2 of 17
Jun 13, 2006
DG408, DG409
Pinouts
DG408 (PDIP, SOIC, TSSOP)
TOP VIEW
DG409 (PDIP, SOIC, TSSOP)
TOP VIEW
Functional Block Diagrams
DG408 DG409
14
15
16
9
13
12
11
10
1
2
3
4
5
7
6
8
A0
EN
V-
S1
S2
S3
D
S4
A1
GND
V+
S5
S6
S7
S8
A2
14
15
16
9
13
12
11
10
1
2
3
4
5
7
6
8
A0
EN
V-
S1A
S2A
S3A
DA
S4A
A1
V+
S1B
S3B
S4B
DB
GND
S2B
TRUTH TABLE DG408
A2A1A0EN ON SWITCH
XXX0 NONE
0001 1
0011 2
0101 3
0111 4
1001 5
1011 6
1101 7
1111 8
DECODER/
DRIVER
D
LEVEL
SHIFT
5V
REF
DIGITAL
INPUT
PROTECTION
S1
S2
S8
A0A1A2EN
TRUTH TABLE DG409
A1A0EN ON SWITCH
XX0 NONE
001 1
011 2
101 3
111 4
NOTES:
1. VAH Logic “1”2.4V.
2. VAL Logic “0” 0.8V.
DECODER/
DRIVER
DA
LEVEL
SHIFT
5V
REF
DIGITAL
INPUT
PROTECTION
S1A
S4A
S1B
A0A1EN
DB
S4B
FN3283 Rev 8.00 Page 3 of 17
Jun 13, 2006
DG408, DG409
Pin Descriptions - (DG408)
PIN SYMBOL DESCRIPTION
1A
0Logic Decode Input (Bit 0, LSB)
2 EN Enable Input
3 V- Negative Power Supply Terminal
4S
1Source (Input) for Channel 1
5S
2Source (Input) for Channel 2
6S
3Source (Input) for Channel 3
7S
4Source (Input) for Channel 4
8 D Drain (Output)
9S
8Source (Input) for Channel 8
10 S7Source (Input) for Channel 7
11 S6Source (Input) for Channel 6
12 S5Source (Input) for Channel 5
13 V+ Positive Power Supply Terminal (Substrate)
14 GND Ground Terminal (Logic Common)
15 A2Logic Decode Input (Bit 2, MSB)
16 A1Logic Decode Input (Bit 1)
Pin Descriptions - (DG409)
PIN SYMBOL DESCRIPTION
1A
0Logic Decode Input (Bit 0, LSB)
2 EN Enable Input
3 V- Negative Power Supply Terminal
4S
1A Source (Input) for Channel 1a
5S
2A Source (Input) for Channel 2a
6S
3A Source (Input) for Channel 3a
7S
4A Source (Input) for Channel 4a
8D
ADrain a (Output a)
9D
BDrain b (Output b)
10 S4B Source (Input) for Channel 4b
11 S3B Source (Input) for Channel 3b
12 S2B Source (Input) for Channel 2b
13 S1B Source (Input) for Channel 1b
14 V+ Positive Power Supply Terminal
15 GND Ground Terminal (Logic Common)
16 A1Logic Decode Input (Bit 1, MSB)
FN3283 Rev 8.00 Page 4 of 17
Jun 13, 2006
DG408, DG409
Absolute Maximum Ratings Thermal Information
V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44.0V
GND to V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25V
Digital Inputs, VS, VD (Note 3). . . . . .(V-) -2V to (V+) + 2V or 20mA,
Whichever Occurs First
Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . 30mA
Peak Current, S or D (Pulsed 1ms, 10% Duty Cycle Max) . . 100mA
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C
Thermal Resistance (Typical, Note 4) JA (°C/W)
PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
TSSOP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150°C
Maximum Storage Temperature Range . . . . . . . . . . -65°C to 125°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300°C
(SOIC and TSSOP - Lead Tips Only)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operat i onal sections of this specification is not implied.
NOTES:
3. Signals on SX, DX, EN or AX exceeding V+ or V- are clamped by internal diodes. Limit diode current to maximum current ratings.
4. JA is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications Test Conditions: V+ = +15V, V- = -15V, VAL = 0.8V, VAH = 2.4V, Unless Otherwise Specified
PARAMETER TEST CONDITIONS TEMP (°C)
(NOTE 5)
MIN
(NOTE 6)
TYP
(NOTE 5)
MAX UNITS
DYNAMIC CHARACTERISTICS
Transition Time, tTRANS (See Figure 1) Full - 160 250 ns
Break-Before-Make Interval, tOPEN (See Figure 3) 25 10 - - ns
Enable Turn-ON Time, tON(EN) (See Figure 2) 25 - 115 150 ns
Full - - 225 ns
Enable Turn-OFF Time, tOFF(EN) (See Figure 2) Full - 105 150 ns
Charge Injection, Q CL = 10nF, VS = 0V 25 - 20 - pC
OFF Isolation VEN = 0V, RL = 1k,
f = 100kHz (Note 9)
25 - -75 - dB
Logic Input Capacitance, CIN f = 1MHz 25 - 8 - pF
Source OFF Capacitance, CS(OFF) VEN = 0V, VS = 0V,
f = 1MHz
25 - 3 - pF
Drain OFF Capacitance, CD(OFF) VEN = 0V, VD = 0V,
f = 1MHz
DG408 25 - 26 - pF
DG409 25 - 14 - pF
Drain ON Capacitance, CD(ON) VEN = 3V, VD = 0V,
f = 1MHz, VA = 0V or 3V
DG408 25 - 37 - pF
DG409 25 - 25 - pF
DIGITAL INPUT CHARACTERISTICS
Logic Input Current,
Input Voltage High, IAH
VA = 2.4V, 15V Full -10 - 10 A
Logic Input Current,
Input Voltage Low, IAL
VEN = 0V, 2.4V,
VA = 0V
Full -10 - 10 A
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, VANALOG Full -15 - 15 V
Drain-Source ON Resistance,
rDS(ON)
VD = 10V, IS = -10mA
(Note 7)
25 - 40 100
Full - - 125
rDS(ON) Matching Between Channels,
rDS(ON)
VD = 10V, -10V (Note 8) 25 - - 15
Source OFF Leakage Current, IS(OFF) VEN = 0V, VS = 10V,
VD = +10V
25 -0.5 - 0.5 nA
Full -5 - 5 nA
FN3283 Rev 8.00 Page 5 of 17
Jun 13, 2006
DG408, DG409
Drain OFF Leakage Current, ID(OFF) VEN = 0V, VD = 10V,
VS = +10V
DG408 25 -1 - 1 nA
Full -20 - 20 nA
DG409 25 -1 - 1 nA
Full -10 - 10 nA
Drain ON Leakage Current, ID(ON) VS = VD = 10V (Note 7)
DG408 25 -1 - 1 nA
Full -20 - 20 nA
DG409 25 -1 - 1 nA
Full -10 - 10 nA
POWER SUPPLY CHARACTERISTICS
Positive Supply Current, I+ VEN = 0V, VA = 0V (Standby) Full - 10 75 A
Negative Supply Current, I- Full -75 1 - A
Positive Supply Current, I+ VEN = 2.4V, VA = 0V
(Enabled)
25 - 0.2 0.5 mA
Full - - 2 mA
Negative Supply Current, I- Full -500 - - A
Electrical Specifications Test Conditions: V+ = +15V, V- = -15V, VAL = 0.8V, VAH = 2.4V, Unless Otherwise Specified (Continued)
PARAMETER TEST CONDITIONS TEMP (°C)
(NOTE 5)
MIN
(NOTE 6)
TYP
(NOTE 5)
MAX UNITS
Electrical Specifications Single Supply Test Conditions: V+ = 12V, V- = 0V, VAL = 0.8V, VAH = 2.4V,
Unless Otherwise Specified
PARAMETER
TEST
CONDITION TEMP (°C)
(NOTE 5)
MIN
(NOTE 6)
TYP
(NOTE 5)
MAX UNITS
DYNAMIC CHARACTERISTICS
Switching Time of Multiplexer, tTRANS VS1 = 8V, VS8 = 0V, VIN = 2.4V 25 - 180 - ns
Enable Turn-ON Time, tON(EN) VINH = 2.4V, VINL = 0V,
VS1 = 5V
25 - 180 - ns
Enable Turn-OFF Time, tOFF(EN) 25 - 120 - ns
Charge Injection, Q CL = 10nF, VGEN = 0V,
RGEN = 0
25 - 5 - pC
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, VANALOG Full 0 - 12 V
Drain-Source ON-Resistance,
rDS(ON)
VD = 3V, 10V, IS = -1mA
(Note 7)
25 - 90 -
NOTES:
5. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
6. Typical values are for DESIGN AID ONLY, not guaranteed nor production tested.
7. Sequence each switch ON.
8. rDS(ON) = rDS(ON) (Max) - rDS(ON) (Min).
9. Worst case isolation occurs on channel 4 due to proximity to the drain pin.
FN3283 Rev 8.00 Page 6 of 17
Jun 13, 2006
DG408, DG409
Test Circuits and Waveforms
FIGURE 1A. DG408 TEST CIRCUIT FIGURE 1B. DG409 TEST CIRCUIT
FIGURE 1C. MEASUREMENT POINTS
FIGURE 1. TRANSITION TIME
FIGURE 2A. DG408 TEST CIRCUIT FIGURE 2B. DG409 TEST CIRCUIT
FIGURE 2C. MEASUREMENT POINTS
FIGURE 2. ENABLE SWITCHING TIMES
EN
A0
DG408
GND
A1
A2
S1
S2 - S7
S8
D
V-
V+
10V
10V
SWITCH
OUTPUT
VO
35pF30050
+15V
+2.4V
-15V
LOGIC
INPUT
EN
DG409
GND
A0
A1
S1B
S1A - S4A, DA
S4B
DB
V-
V+
10V
10V
SWITCH
OUTPUT
VO
35pF30050
+15V
+2.4V
-15V
LOGIC
INPUT
LOGIC
INPUT
SWITCH
OUTPUT
VO
3V
VS1
S1ON
50%
tr < 20ns
tf < 20ns
tTRANS
50%
0V
0V
VS8
tTRANS
S8ON
0.8 VS8
0.8 VS1
EN
A0DG408
GND
A1
A2
S1
S2 - S8
D
V-
V+ -5V
SWITCH
OUTPUT
VO
35pF30050
+15V
-15V
LOGIC
INPUT VIN
EN
A0DG409
GND
A1
S1B
S1A - S4A
DB
V-
V+ -5V
SWITCH
OUTPUT
Vo
35pF30050
+15V
-15V
LOGIC
INPUT S2B - S4B, DA
VIN
LOGIC
INPUT
SWITCH
OUTPUT
VO
3V
VO
50%
tr < 20ns
tf < 20ns
tON(EN)
0V
50%
tOFF(EN)
0.9 VO
0V
VIN
FN3283 Rev 8.00 Page 7 of 17
Jun 13, 2006
DG408, DG409
FIGURE 3A. TEST CIRCUIT FIGURE 3B. MEASUREMENT POINTS
FIGURE 3. BREAK-BEFORE-MAKE INTERVAL
FIGURE 4A. TEST CIRCUIT FIGURE 4B. MEASUREMENT POINTS
FIGURE 4. CHARGE INJECTION
FIGURE 5. OFF ISOLATION FIGURE 6. CROSSTALK
Test Circuits and Waveforms (Continued)
EN
A0DG408
GND
A1
A2
ALL S AND DA
D, DB
V-
V+
+5V (VS)
SWITCH
OUTPUT
VO
35pF30050
+15V
+2.4V
-15V
LOGIC
INPUT
DG409
LOGIC
INPUT
SWITCH
OUTPUT
VO
3V
VS
80%
tr < 20ns
tf < 20ns
tOPEN
0V
0V
80%
SX
A0
GND
A1
EN
D
V-
V+
VO
CL
+15V
-15V
A2
10nF
VGEN CHANNEL
SELECT
RGEN
LOGIC INPUT
LOGIC
INPUT
SWITCH
OUTPUT VO
3V
ON OFF
0V
VO IS THE MEASURED VOLTAGE DUE
TO CHARGE TRANSFER ERROR, Q
Q = CL xVO
SX
A2
GND
A1
EN
D
V-
V+
VO
+15V
-15V
A0
SIGNAL
GENERATOR
VIN
0V
1k
ANALYZER
|
|
S8
OFF ISOLATION 20 Log
VOUT
VIN
-----------------=
SX
A2
GND
A1
EN
D
V-
V+
VO
+15V
-15V
A0
SIGNAL
GENERATOR
VIN
5V
1k
ANALYZER
|
|
S8
CROSSTALK 20 Log
VOUT
VIN
-----------------=
S1
1k
FN3283 Rev 8.00 Page 8 of 17
Jun 13, 2006
DG408, DG409
Typical Applications
Overvoltage Protection
A very convenient form of overvoltage protection consists of
adding two small signal diodes (1N4148, 1N914 type) in
series with the supply pins (see Figure 9). This arrangement
effectively blocks the flow of reverse currents. It also floats
the supply pin above or below the normal V+ or V- value. In
this case the overvoltage signal actually becomes the power
supply of the IC. From the point of view of the chip, nothing
has changed, as long as the difference V+ - (V-) doesn’t
exceed 44V. The addition of these diodes will reduce the
analog signal range to 1V below V+ and 1V above V-, but it
preserves the low channel resistance and low leakage
characteristics.
Typical application information is for Design Aid Only, not
guaranteed and not subject to production testing.
FIGURE 7. INSERTION LOSS FIGURE 8. SOURCE/DRAIN CAPACITANCES
Test Circuits and Waveforms (Continued)
A2
GND
A1
EN
D
V-
V+
VO
+15V
-15V
A0
SIGNAL
GENERATOR
VIN
5V
RL
ANALYZER
INSERTION LOSS 20 Log
VOUT
VIN
-----------------=
S1
IMPEDANCE
ANALYZER
A2
GND
A1
EN
V-
V+
+15V
-15V
A0
CHANNEL
SELECT
3V OR 0V
S8
S1
|
|
D
1N4148
1N4148
DG408
V-
VG
SX
V+
D
FIGURE 9. OVERVOLTAGE PROTECTION USING BLOCKING
DIODES
FN3283 Rev 8.00 Page 9 of 17
Jun 13, 2006
DG408, DG409
Typical Performance Curves
FIGURE 10. INPUT LOGIC CURRENT vs LOGIC INPUT
VOLTAGE
FIGURE 11. SOURCE/DRAIN CAPACITANCE vs ANALOG
VOLTAGE (SINGLE 12V SUPPLY)
FIGURE 12. SOURCE/DRAIN CAPACITANCE vs ANALOG
VOLTAGE
FIGURE 13. LOGIC INPUT CURRENT vs TEMPERATURE
FIGURE 14. DRAIN LEAKAGE CURRENT vs SOURCE/DRAIN
VOLTAGE (SINGLE 12V SUPPLY)
FIGURE 15. DRAIN LEAKAGE CURRENT vs SOURCE/DRAIN
VOLTAGE
V+ = +15V
3.5
3.0
2.0
1.0
0.5pA
0.0
-1.0
0 5 10 15
IIN (pA)
VIN (V)
V- = -15V
CD(ON)
CD(OFF)
CS(OFF)
75
50
25
0
04812
VA (V)
CS, D (pF)
V+ = +15V
V- = -15V
CD(ON)
CD(OFF)
CS(OFF)
80
60
40
20
0
-15 0 15
VA (V)
CS, D (pF)
VSUPPLY = 15V
VIN = 0V
0
-200
-400
-600
-800
-55 5 45 85 125
TEMPERATURE (°C)
IIN (pA)
DG408 ID(OFF)
DG409 ID(OFF)
DG409 ID(ON)
DG408 ID(ON)
VS = 0V FOR ID(OFF)
VS = VD FOR ID(ON)
60
40
20
0
-20
-40
-60
0 24681012
VD (V)
ID (pA)
V+ = 15V
V- = -15V
VS = -VD FOR ID(OFF)
VD = VS(OPEN) FOR ID(ON)
100
60
20
-20
-60
-100
-140
-15 0 15
VS, VD (V)
ID (pA)
DG409 ID(OFF)
DG408 ID(ON), ID(OFF)
DG409 ID(ON)
FN3283 Rev 8.00 Page 10 of 17
Jun 13, 2006
DG408, DG409
FIGURE 16. SOURCE LEAKAGE CURRENT vs SOURCE
VOLTAGE
FIGURE 17. INPUT SWITCHING THRESHOLD vs SUPPLY
VOLTAGE
FIGURE 18. NEGATIVE SUPPLY CURRENT vs SWITCHING
FREQUENCY
FIGURE 19. POSITIVE SUPPLY CURRENT vs SWITCHING
FREQUENCY
FIGURE 20. ISUPPLY vs TEMPERATURE FIGURE 21. NEGATIVE SUPPLY CURRENT vs TEMPERATURE
Typical Performance Curves (Continued)
VS (V)
20
15
10
5
0
-5
-10
-15 0 15
IS(OFF) (pA)
V+ = +12V
V- = 0V
V+ = +15V
V- = -15V
2.0
1.5
1.0
0.5
0.0
4 8 12 16 20
VIN (V)
VSUPPLY (V)
VSUPPLY = 15V
EN = 2.4V
EN = 0V
105
104
103
102
10
1
0.1
100 1K 10K 100K 1M 10M
SWITCHING FREQUENCY (Hz)
-(I-) (A)
VSUPPLY = 15V
EN = 2.4V
EN = 0V
104
103
102
10
1
0.1
0.01
100 1k 10k 100k 1M 10M
SWITCHING FREQUENCY (Hz)
I+ (mA)
VSUPPLY = 15V
I+
-(I-)
105
104
103
102
10
1
0.1
-55 5 45 85 125
TEMPERATURE (°C)
I+, I- (nA)
0.01
V+ = 15V
V- = -15V
VIN = 0V
VEN = 0V
0
-200
-400
-600
-800
-55 5 125
TEMPERATURE (°C)
I- (nA)
45 85
FN3283 Rev 8.00 Page 11 of 17
Jun 13, 2006
DG408, DG409
FIGURE 22. POSITIVE SUPPLY CURRENT vs TEMPERATURE
(DG408)
FIGURE 23. CHARGE INJECTION vs ANALOG VOLTAGE
FIGURE 24. rDS(ON) vs VD AND SUPPLY FIGURE 25. rDS(ON) vs VD (SINGLE SUPPLY)
FIGURE 26. rDS(ON) vs VS AND TEMPERATURE FIGURE 27. rDS(ON) vs VS AND TEMPERATURE
(SINGLE SUPPLY)
Typical Performance Curves (Continued)
V+ = 15V
V- = -15V
VIN = 0V
VEN = 0V
20
15
10
5
0
-55 5 125
TEMPERATURE (°C)
I+ (A)
45 85
90
80
70
60
50
40
30
20
10
0
-10
-15 -10 -5 0 5 10
Q (pC)
VS (V)
CL = 10,000pF
VIN = 5VP-P
V+ = 12V
V- = 0V
V+ = 15V
V- = -15V
15
120
100
80
60
40
20
0
-20 -16 -12 -8 -4 0 4 8 12 16 20
rDS(ON) ()
VD (V)
10V
5V
8V
12V
15V
20V
160
140
120
100
80
60
0
04 812162022
rDS(ON) ()
VD (V)
10V
12V
15V
20V
40
20
22V
V+ = 7.5V
V- = 0V
80
70
60
50
40
30
0
-15 0 15
rDS(ON) ()
VS (V)
20
10
V+ = 15V
V- = -15V
25°C
125°C
-55°C
85°C
-40°C
0°C
130
110
90
70
50
30
0812
rDS(ON) ()
VS (V)
10
V+ = 12V
V- = 0V
25°C
125°C
85°C
4
-55°C
-40°C
0°C
FN3283 Rev 8.00 Page 12 of 17
Jun 13, 2006
DG408, DG409
FIGURE 28. OFF ISOLATION AND CROSSTALK vs FREQUENCY FIGURE 29. SWITCHING TIME vs SINGLE SUPPLY
FIGURE 30. SWITCHING TIME vs BIPOLAR SUPPLY FIGURE 31. SWITCHING TIME vs VIN (SINGLE SUPPLY)
FIGURE 32. SWITCHING TIME vs VIN (BIPOLAR SUPPLY) FIGURE 33. INSERTION LOSS vs FREQUENCY
Typical Performance Curves (Continued)
V+ = +15V
V- = -15V
RL = 1k
OFF ISOLATION
CROSSTALK
-150
-130
-110
-90
-70
-50
-30
100 1k 10k 100k 1M 10M 100M
FREQUENCY (Hz)
(dB)
tTRANS
tON(EN)
tOFF(EN)
VSUPPLY (V)
t (ns)
275
250
225
200
175
150
125
100
89101112131415
200
175
150
125
100
75
10 12 14 16 18 20 22
VSUPPLY (V)
t (ns)
tTRANS
tON(EN)
tOFF(EN)
190
170
150
130
110
90
2345
VIN (V)
t (ns)
tTRANS
tON(EN)
tOFF(EN)
180
160
140
120
100
80
234 5
VIN (V)
t (ns)
tTRANS
tON(EN)
tOFF(EN)
V+ = +15V
V- = -15V
REF. 1VRMS
RL = 1k
RL = 50
1
0
-1
-2
-3
-4
-5
-6
10 102103104105106107108
FREQUENCY (Hz)
LOSS (dB)
FN3283 Rev 8.00 Page 13 of 17
Jun 13, 2006
DG408, DG409
Die Characteristics
DIE DIMENSIONS:
1800m x 3320m x 485m
METALLIZATION:
Type: SiAl
Thickness: 12kÅ 1kÅ
PASSIVATION:
Type: Nitride
Thickness: 8kÅ 1kÅ
WORST CASE CURRENT DENSITY:
9.1 x 104 A/cm2
Metallization Mask Layout
DG408
EN A0A1A2GND
(2) (1) (16) (15) (14)
V- (3)
S1 (4)
S2 (5)
S3 (6)
S4 (7)
D
(8)
S8
(9)
S7
(10)
NC
(13) V+
(12) S5
(11) S6
NC
FN3283 Rev 8.00 Page 14 of 17
Jun 13, 2006
DG408, DG409
Die Characteristics
DIE DIMENSIONS:
1800m x 3320m x 485m
METALLIZATION:
Type: SiAl
Thickness: 12kÅ 1kÅ
PASSIVATION:
Type: Nitride
Thickness: 8kÅ 1kÅ
WORST CASE CURRENT DENSITY:
9.1 x 104 A/cm2
Metallization Mask Layout
DG409
EN A0A1GND
(2) (1) (16) NC (15)
DA
(8)
NC
(14) V+
(13) S1B
(12) S2B
(11) S3B
DB
(9)
S4B
(10)
V- (3)
S1A (4)
S2A (5)
S3A (6)
S4A (7)
FN3283 Rev 8.00 Page 15 of 17
Jun 13, 2006
DG408, DG409
Thin Shrink Small Outline Plastic Packages (TSSOP)
NOTES:
1. These package dimensions are within allowable dimensions of
JEDEC MO-153-AB, Issue E.
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
3. Dimension “D” does not include mold flash, protrusions or gate
burrs. Mold flash, protrusion and gate burrs shall not exceed
0.15mm (0.006 inch) per side.
4. Dimension “E1” does not include interlead flash or protrusions.
Interlead flash and protrusions shall not exceed 0.15mm (0.006
inch) per side.
5. The chamfer on the body is optional. If it is not present, a visual
index feature must be located within the crosshatched area.
6. “L” is the length of terminal for soldering to a substrate.
7. “N” is the number of terminal positions.
8. Terminal numbers are shown for reference only.
9. Dimension “b” does not include dambar protrusion. Allowable
dambar protrusion shall be 0.08mm (0.003 inch) total in excess
of “b” dimension at maximum material condition. Minimum space
between protrusion and adjacent lead is 0.07mm (0.0027 inch).
10. Controlling dimension: MILLIMETER. Converted inch dimen-
sions are not necessarily exact. (Angles in degrees)
INDEX
AREA E1
D
N
123
-B-
0.10(0.004) C AMBS
e
-A-
b
M
-C-
A1
A
SEATING PLANE
0.10(0.004)
c
E0.25(0.010) BM M
L
0.25
0.010
GAUGE
PLANE
A2
0.05(0.002)
M16.173
16 LEAD THIN SHRINK SMALL OUTLINE PLASTIC PACKAGE
SYMBOL
INCHES MILLIMETERS
NOTESMIN MAX MIN MAX
A - 0.043 - 1.10 -
A1 0.002 0.006 0.05 0.15 -
A2 0.033 0.037 0.85 0.95 -
b 0.0075 0.012 0.19 0.30 9
c 0.0035 0.008 0.09 0.20 -
D 0.193 0.201 4.90 5.10 3
E1 0.169 0.177 4.30 4.50 4
e 0.026 BSC 0.65 BSC -
E 0.246 0.256 6.25 6.50 -
L 0.020 0.028 0.50 0.70 6
N16 167
0o8o0o8o-
Rev. 1 2/02
FN3283 Rev 8.00 Page 16 of 17
Jun 13, 2006
DG408, DG409
Dual-In-Line Plastic Packages (PDIP)
NOTES:
1. Controlling Dimensions: INCH. In case of conflict between English and
Metric dimensions, the inch dimensions control.
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
3. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of
Publication No. 95.
4. Dimensions A, A1 and L are measured with the package seated in JE-
DEC seating plane gauge GS-3.
5. D, D1, and E1 dimensions do not include mold flash or protrusions.
Mold flash or protrusions shall not exceed 0.010 inch (0.25mm).
6. E and are measured with the leads constrained to be perpendic-
ular to datum .
7. eB and eC are measured at the lead tips with the leads unconstrained.
eC must be zero or greater.
8. B1 maximum dimensions do not include dambar protrusions. Dambar
protrusions shall not exceed 0.010 inch (0.25mm).
9. N is the maximum number of terminal positions.
10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3, E28.3,
E42.6 will have a B1 dimension of 0.030 - 0.045 inch (0.76 - 1.14mm).
eA
-C-
C
L
E
eA
C
eB
eC
-B-
E1
INDEX 12 3 N/2
N
AREA
SEATING
BASE
PLANE
PLANE
-C-
D1
B1
B
e
D
D1
A
A2
L
A1
-A-
0.010 (0.25) C AMBS
E16.3 (JEDEC MS-001-BB ISSUE D)
16 LEAD DUAL-IN-LINE PLASTIC PACKAGE
SYMBOL
INCHES MILLIMETERS
NOTESMIN MAX MIN MAX
A - 0.210 - 5.33 4
A1 0.015 - 0.39 - 4
A2 0.115 0.195 2.93 4.95 -
B 0.014 0.022 0.356 0.558 -
B1 0.045 0.070 1.15 1.77 8, 10
C 0.008 0.014 0.204 0.355 -
D 0.735 0.775 18.66 19.68 5
D1 0.005 - 0.13 - 5
E 0.300 0.325 7.62 8.25 6
E1 0.240 0.280 6.10 7.11 5
e 0.100 BSC 2.54 BSC -
eA0.300 BSC 7.62 BSC 6
eB- 0.430 - 10.92 7
L 0.115 0.150 2.93 3.81 4
N16 169
Rev. 0 12/93
FN3283 Rev 8.00 Page 17 of 17
Jun 13, 2006
DG408, DG409
Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted
in the quality certifications found at www.intersil.com/en/support/qualandreliability.html
Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such
modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are
current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its
subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
For additional products, see www.intersil.com/en/products.html
© Copyright Intersil Americas LLC 1999-2006. All Rights Reserved.
All trademarks and registered trademarks are the property of their respective owners.
Small Outline Plastic Packages (SOIC)
NOTES:
1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of
Publication Number 95.
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
3. Dimension “D” does not include mold flash, protrusions or gate burrs.
Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006
inch) per side.
4. Dimension “E” does not include interlead flash or protrusions. Interlead
flash and protrusions shall not exceed 0.25mm (0.010 inch) per side.
5. The chamfer on the body is optional. If it is not present, a visual index
feature must be located within the crosshatched area.
6. “L” is the length of terminal for soldering to a substrate.
7. “N” is the number of terminal positions.
8. Terminal numbers are shown for reference only.
9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above
the seating plane, shall not exceed a maximum value of 0.61mm
(0.024 inch).
10. Controlling dimension: MILLIMETER. Converted inch dimensions are
not necessarily exact.
INDEX
AREA
E
D
N
123
-B-
0.25(0.010) C AMBS
e
-A-
L
B
M
-C-
A1
A
SEATING PLANE
0.10(0.004)
h x 45°
C
H0.25(0.010) BM M
M16.15 (JEDEC MS-012-AC ISSUE C)
16 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE
SYMBOL
INCHES MILLIMETERS
NOTESMIN MAX MIN MAX
A 0.0532 0.0688 1.35 1.75 -
A1 0.0040 0.0098 0.10 0.25 -
B 0.013 0.020 0.33 0.51 9
C 0.0075 0.0098 0.19 0.25 -
D 0.3859 0.3937 9.80 10.00 3
E 0.1497 0.1574 3.80 4.00 4
e 0.050 BSC 1.27 BSC -
H 0.2284 0.2440 5.80 6.20 -
h 0.0099 0.0196 0.25 0.50 5
L 0.016 0.050 0.40 1.27 6
N16 167
-
Rev. 1 6/05