PIC16F84A 18-pin Enhanced FLASH/EEPROM 8-Bit Microcontroller High Performance RISC CPU Features: * 13 I/O pins with individual direction control * High current sink/source for direct LED drive - 25 mA sink max. per pin - 25 mA source max. per pin * TMR0: 8-bit timer/counter with 8-bit programmable prescaler Special Microcontroller Features: * 10,000 erase/write cycles Enhanced FLASH Program memory typical * 10,000,000 typical erase/write cycles EEPROM Data memory typical * EEPROM Data Retention > 40 years * In-Circuit Serial ProgrammingTM (ICSPTM) - via two pins * Power-on Reset (POR), Power-up Timer (PWRT), Oscillator Start-up Timer (OST) * Watchdog Timer (WDT) with its own On-Chip RC Oscillator for reliable operation * Code protection * Power saving SLEEP mode * Selectable oscillator options 2001-2013 Microchip Technology Inc. RA2 1 18 RA1 RA3 2 17 RA0 RA4/T0CKI 3 16 OSC1/CLKIN MCLR 4 15 OSC2/CLKOUT VSS 5 14 VDD RB0/INT 6 13 RB7 RB1 7 12 RB6 RB2 8 11 RB5 RB3 9 10 RB4 RA2 1 20 RA1 RA3 2 19 RA0 RA4/T0CKI 3 18 OSC1/CLKIN MCLR VSS 4 17 OSC2/CLKOUT 16 VDD VSS 6 15 RB0/INT 7 14 VDD RB7 RB1 8 13 RB6 RB2 9 12 RB5 RB3 10 11 RB4 SSOP 5 PIC16F84A Peripheral Features: PDIP, SOIC PIC16F84A * Only 35 single word instructions to learn * All instructions single-cycle except for program branches which are two-cycle * Operating speed: DC - 20 MHz clock input DC - 200 ns instruction cycle * 1024 words of program memory * 68 bytes of Data RAM * 64 bytes of Data EEPROM * 14-bit wide instruction words * 8-bit wide data bytes * 15 Special Function Hardware registers * Eight-level deep hardware stack * Direct, indirect and relative addressing modes * Four interrupt sources: - External RB0/INT pin - TMR0 timer overflow - PORTB<7:4> interrupt-on-change - Data EEPROM write complete Pin Diagrams CMOS Enhanced FLASH/EEPROM Technology: * Low power, high speed technology * Fully static design * Wide operating voltage range: - Commercial: 2.0V to 5.5V - Industrial: 2.0V to 5.5V * Low power consumption: - < 2 mA typical @ 5V, 4 MHz - 15 A typical @ 2V, 32 kHz - < 0.5 A typical standby current @ 2V DS35007C-page 1 PIC16F84A Table of Contents 1.0 Device Overview .......................................................................................................................................................................... 3 2.0 Memory Organization ................................................................................................................................................................... 5 3.0 Data EEPROM Memory ............................................................................................................................................................. 13 4.0 I/O Ports ..................................................................................................................................................................................... 15 5.0 Timer0 Module ........................................................................................................................................................................... 19 6.0 Special Features of the CPU ...................................................................................................................................................... 21 7.0 Instruction Set Summary ............................................................................................................................................................ 35 8.0 Development Support................................................................................................................................................................. 43 9.0 Electrical Characteristics ............................................................................................................................................................ 47 10.0 DC/AC Characteristic Graphs .................................................................................................................................................... 59 11.0 Packaging Information................................................................................................................................................................ 69 Appendix A: Revision History .............................................................................................................................................................. 77 Appendix B: Conversion Considerations.............................................................................................................................................. 78 Appendix C: Migration from Baseline to Mid-range Devices80 INDEX .................................................................................................................................................................................................. 81 The Microchip Web Site ....................................................................................................................................................................... 85 Customer Change Notification Service ................................................................................................................................................ 85 Customer Support ................................................................................................................................................................................ 85 Reader Response ................................................................................................................................................................................ 86 PIC16F84A Product Identification System ........................................................................................................................................... 87 TO OUR VALUED CUSTOMERS It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and enhanced as new volumes and updates are introduced. If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via E-mail at docerrors@microchip.com or fax the Reader Response Form in the back of this data sheet to (480) 792-4150. We welcome your feedback. Most Current Data Sheet To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at: http://www.microchip.com You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page. The last character of the literature number is the version number, (e.g., DS30000A is version A of document DS30000). Errata An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision of silicon and revision of document to which it applies. To determine if an errata sheet exists for a particular device, please check with one of the following: * Microchip's Worldwide Web site; http://www.microchip.com * Your local Microchip sales office (see last page) When contacting a sales office, please specify which device, revision of silicon and data sheet (include literature number) you are using. Customer Notification System Register on our web site at www.microchip.com to receive the most current information on all of our products. DS35007C-page 2 2001-2013 Microchip Technology Inc. PIC16F84A 1.0 DEVICE OVERVIEW The program memory contains 1K words, which translates to 1024 instructions, since each 14-bit program memory word is the same width as each device instruction. The data memory (RAM) contains 68 bytes. Data EEPROM is 64 bytes. This document contains device specific information for the operation of the PIC16F84A device. Additional information may be found in the PIC(R) Mid-Range Reference Manual, (DS33023), which may be downloaded from the Microchip website. The Reference Manual should be considered a complementary document to this data sheet, and is highly recommended reading for a better understanding of the device architecture and operation of the peripheral modules. There are also 13 I/O pins that are user-configured on a pin-to-pin basis. Some pins are multiplexed with other device functions. These functions include: * External interrupt * Change on PORTB interrupt * Timer0 clock input The PIC16F84A belongs to the mid-range family of the PIC(R) microcontroller devices. A block diagram of the device is shown in Figure 1-1. FIGURE 1-1: Table 1-1 details the pinout of the device with descriptions and details for each pin. PIC16F84A BLOCK DIAGRAM Data Bus 13 8 Program Counter EEPROM Data Memory FLASH Program Memory 8 Level Stack (13-bit) 1K x 14 Program Bus 14 RAM File Registers EEDATA 68 x 8 7 RAM Addr EEPROM Data Memory 64 x 8 EEADR Addr Mux Instruction Register 7 Direct Addr 5 TMR0 Indirect Addr FSR reg RA4/T0CKI STATUS reg 8 MUX Power-up Timer Instruction Decode & Control Timing Generation Oscillator Start-up Timer 8 ALU Power-on Reset Watchdog Timer I/O Ports RA3:RA0 W reg RB7:RB1 RB0/INT OSC2/CLKOUT OSC1/CLKIN MCLR 2001-2013 Microchip Technology Inc. VDD, VSS DS35007C-page 3 PIC16F84A TABLE 1-1: PIC16F84A PINOUT DESCRIPTION PDIP No. SOIC No. SSOP No. I/O/P Type OSC1/CLKIN 16 16 18 I OSC2/CLKOUT 15 15 19 O -- Oscillator crystal output. Connects to crystal or resonator in Crystal Oscillator mode. In RC mode, OSC2 pin outputs CLKOUT, which has 1/4 the frequency of OSC1 and denotes the instruction cycle rate. MCLR 4 4 4 I/P ST Master Clear (Reset) input/programming voltage input. This pin is an active low RESET to the device. Pin Name Buffer Type Description ST/CMOS(3) Oscillator crystal input/external clock source input. PORTA is a bi-directional I/O port. RA0 17 17 19 I/O TTL RA1 18 18 20 I/O TTL RA2 1 1 1 I/O TTL RA3 2 2 2 I/O TTL RA4/T0CKI 3 3 3 I/O ST Can also be selected to be the clock input to the TMR0 timer/counter. Output is open drain type. PORTB is a bi-directional I/O port. PORTB can be software programmed for internal weak pull-up on all inputs. RB0/INT 6 6 7 I/O TTL/ST(1) RB1 7 7 8 I/O TTL RB2 8 8 9 I/O TTL RB3 9 9 10 I/O TTL RB4 10 10 11 I/O TTL RB5 11 11 12 I/O TTL RB0/INT can also be selected as an external interrupt pin. Interrupt-on-change pin. Interrupt-on-change pin. (2) Interrupt-on-change pin. Serial programming clock. RB6 12 12 13 I/O TTL/ST RB7 13 13 14 I/O TTL/ST(2) VSS 5 5 5,6 P -- Ground reference for logic and I/O pins. VDD 14 14 15,16 P -- Positive supply for logic and I/O pins. Interrupt-on-change pin. Serial programming data. Legend: I= input O = Output I/O = Input/Output P = Power -- = Not used TTL = TTL input ST = Schmitt Trigger input Note 1: This buffer is a Schmitt Trigger input when configured as the external interrupt. 2: This buffer is a Schmitt Trigger input when used in Serial Programming mode. 3: This buffer is a Schmitt Trigger input when configured in RC oscillator mode and a CMOS input otherwise. DS35007C-page 4 2001-2013 Microchip Technology Inc. PIC16F84A MEMORY ORGANIZATION There are two memory blocks in the PIC16F84A. These are the program memory and the data memory. Each block has its own bus, so that access to each block can occur during the same oscillator cycle. The data memory can further be broken down into the general purpose RAM and the Special Function Registers (SFRs). The operation of the SFRs that control the "core" are described here. The SFRs used to control the peripheral modules are described in the section discussing each individual peripheral module. The data memory area also contains the data EEPROM memory. This memory is not directly mapped into the data memory, but is indirectly mapped. That is, an indirect address pointer specifies the address of the data EEPROM memory to read/write. The 64 bytes of data EEPROM memory have the address range 0h-3Fh. More details on the EEPROM memory can be found in Section 3.0. FIGURE 2-1: PROGRAM MEMORY MAP AND STACK - PIC16F84A PC<12:0> 13 CALL, RETURN RETFIE, RETLW Stack Level 1 Stack Level 8 RESET Vector 0000h Peripheral Interrupt Vector 0004h User Memory Space 2.0 Additional information on device memory may be found in the PIC(R) Mid-Range Reference Manual, (DS33023). 2.1 Program Memory Organization The PIC16FXX has a 13-bit program counter capable of addressing an 8K x 14 program memory space. For the PIC16F84A, the first 1K x 14 (0000h-03FFh) are physically implemented (Figure 2-1). Accessing a location above the physically implemented address will cause a wraparound. For example, for locations 20h, 420h, 820h, C20h, 1020h, 1420h, 1820h, and 1C20h, the instruction will be the same. 3FFh 1FFFh The RESET vector is at 0000h and the interrupt vector is at 0004h. 2001-2013 Microchip Technology Inc. DS35007C-page 5 PIC16F84A 2.2 Data Memory Organization The data memory is partitioned into two areas. The first is the Special Function Registers (SFR) area, while the second is the General Purpose Registers (GPR) area. The SFRs control the operation of the device. Portions of data memory are banked. This is for both the SFR area and the GPR area. The GPR area is banked to allow greater than 116 bytes of general purpose RAM. The banked areas of the SFR are for the registers that control the peripheral functions. Banking requires the use of control bits for bank selection. These control bits are located in the STATUS Register. Figure 2-2 shows the data memory map organization. Instructions MOVWF and MOVF can move values from the W register to any location in the register file ("F"), and vice-versa. The entire data memory can be accessed either directly using the absolute address of each register file or indirectly through the File Select Register (FSR) (Section 2.5). Indirect addressing uses the present value of the RP0 bit for access into the banked areas of data memory. Data memory is partitioned into two banks which contain the general purpose registers and the special function registers. Bank 0 is selected by clearing the RP0 bit (STATUS<5>). Setting the RP0 bit selects Bank 1. Each Bank extends up to 7Fh (128 bytes). The first twelve locations of each Bank are reserved for the Special Function Registers. The remainder are General Purpose Registers, implemented as static RAM. 2.2.1 FIGURE 2-2: REGISTER FILE MAP PIC16F84A File Address File Address 00h Indirect addr.(1) Indirect addr.(1) 80h 01h TMR0 OPTION_REG 81h 02h PCL PCL 82h 03h STATUS STATUS 83h 04h FSR FSR 84h 05h PORTA TRISA 85h 06h PORTB TRISB 86h 07h -- -- 87h 08h EEDATA EECON1 88h 09h EEADR EECON2(1) 89h 0Ah PCLATH PCLATH 8Ah 0Bh INTCON INTCON 8Bh 8Ch 0Ch 68 General Purpose Registers (SRAM) Mapped (accesses) in Bank 0 4Fh 50h CFh D0h GENERAL PURPOSE REGISTER FILE Each General Purpose Register (GPR) is 8-bits wide and is accessed either directly or indirectly through the FSR (Section 2.5). The GPR addresses in Bank 1 are mapped to addresses in Bank 0. As an example, addressing location 0Ch or 8Ch will access the same GPR. DS35007C-page 6 FFh 7Fh Bank 0 Bank 1 Unimplemented data memory location, read as '0'. Note 1: Not a physical register. 2001-2013 Microchip Technology Inc. PIC16F84A 2.3 Special Function Registers The special function registers can be classified into two sets, core and peripheral. Those associated with the core functions are described in this section. Those related to the operation of the peripheral features are described in the section for that specific feature. The Special Function Registers (Figure 2-2 and Table 2-1) are used by the CPU and Peripheral functions to control the device operation. These registers are static RAM. TABLE 2-1: Addr SPECIAL FUNCTION REGISTER FILE SUMMARY Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on Power-on RESET Details on page Bank 0 00h INDF Uses contents of FSR to address Data Memory (not a physical register) ---- ---- 11 01h TMR0 8-bit Real-Time Clock/Counter xxxx xxxx 20 02h PCL Low Order 8 bits of the Program Counter (PC) 0000 0000 11 0001 1xxx 8 (2) 03h STATUS 04h FSR 05h PORTA(4) 06h PORTB(5) IRP RP1 RP0 TO PD Z DC C RA0 Indirect Data Memory Address Pointer 0 -- -- -- RA4/T0CKI RA3 RA2 RA1 RB7 RB6 RB5 RB4 RB3 RB2 RB1 07h -- 08h EEDATA EEPROM Data Register 09h EEADR EEPROM Address Register xxxx xxxx 11 ---x xxxx 16 RB0/INT xxxx xxxx 18 Unimplemented location, read as '0' 0Ah PCLATH -- -- -- 0Bh INTCON GIE EEIE T0IE Write Buffer for upper 5 bits of the PC INTE RBIE T0IF (1) INTF RBIF -- -- xxxx xxxx 13,14 xxxx xxxx 13,14 ---0 0000 11 0000 000x 10 ---- ---- 11 1111 1111 9 0000 0000 11 0001 1xxx 8 Bank 1 80h INDF 81h OPTION_REG Uses Contents of FSR to address Data Memory (not a physical register) 82h PCL 83h STATUS (2) 84h FSR 85h TRISA 86h TRISB RBPU INTEDG T0CS T0SE PSA PS2 PS1 PS0 PD Z DC C Low order 8 bits of Program Counter (PC) IRP RP1 RP0 TO Indirect data memory address pointer 0 -- -- -- PORTA Data Direction Register PORTB Data Direction Register 87h -- 88h EECON1 89h EECON2 Unimplemented location, read as '0' -- -- -- EEIF WRERR WREN WR RD EEPROM Control Register 2 (not a physical register) 0Ah PCLATH -- -- -- 0Bh INTCON GIE EEIE T0IE Write buffer for upper 5 bits of the PC INTE RBIE T0IF (1) INTF RBIF xxxx xxxx 11 ---1 1111 16 1111 1111 18 -- -- ---0 x000 13 ---- ---- 14 ---0 0000 11 0000 000x 10 Legend: x = unknown, u = unchanged. - = unimplemented, read as '0', q = value depends on condition Note 1: The upper byte of the program counter is not directly accessible. PCLATH is a slave register for PC<12:8>. The contents of PCLATH can be transferred to the upper byte of the program counter, but the contents of PC<12:8> are never transferred to PCLATH. 2: The TO and PD status bits in the STATUS register are not affected by a MCLR Reset. 3: Other (non power-up) RESETS include: external RESET through MCLR and the Watchdog Timer Reset. 4: On any device RESET, these pins are configured as inputs. 5: This is the value that will be in the port output latch. 2001-2013 Microchip Technology Inc. DS35007C-page 7 PIC16F84A 2.3.1 STATUS REGISTER Note 1: The IRP and RP1 bits (STATUS<7:6>) are not used by the PIC16F84A and should be programmed as cleared. Use of these bits as general purpose R/W bits is NOT recommended, since this may affect upward compatibility with future products. The STATUS register contains the arithmetic status of the ALU, the RESET status and the bank select bit for data memory. As with any register, the STATUS register can be the destination for any instruction. If the STATUS register is the destination for an instruction that affects the Z, DC or C bits, then the write to these three bits is disabled. These bits are set or cleared according to device logic. Furthermore, the TO and PD bits are not writable. Therefore, the result of an instruction with the STATUS register as destination may be different than intended. 2: The C and DC bits operate as a borrow and digit borrow out bit, respectively, in subtraction. See the SUBLW and SUBWF instructions for examples. 3: When the STATUS register is the destination for an instruction that affects the Z, DC or C bits, then the write to these three bits is disabled. The specified bit(s) will be updated according to device logic For example, CLRF STATUS will clear the upper three bits and set the Z bit. This leaves the STATUS register as 000u u1uu (where u = unchanged). Only the BCF, BSF, SWAPF and MOVWF instructions should be used to alter the STATUS register (Table 7-2), because these instructions do not affect any status bit. REGISTER 2-1: STATUS REGISTER (ADDRESS 03h, 83h) R/W-0 R/W-0 R/W-0 R-1 R-1 R/W-x R/W-x R/W-x IRP RP1 RP0 TO PD Z DC C bit 7 bit 0 bit 7-6 Unimplemented: Maintain as `0' bit 5 RP0: Register Bank Select bits (used for direct addressing) 01 = Bank 1 (80h - FFh) 00 = Bank 0 (00h - 7Fh) bit 4 TO: Time-out bit 1 = After power-up, CLRWDT instruction, or SLEEP instruction 0 = A WDT time-out occurred bit 3 PD: Power-down bit 1 = After power-up or by the CLRWDT instruction 0 = By execution of the SLEEP instruction bit 2 Z: Zero bit 1 = The result of an arithmetic or logic operation is zero 0 = The result of an arithmetic or logic operation is not zero bit 1 DC: Digit carry/borrow bit (ADDWF, ADDLW,SUBLW,SUBWF instructions) (for borrow, the polarity is reversed) 1 = A carry-out from the 4th low order bit of the result occurred 0 = No carry-out from the 4th low order bit of the result bit 0 C: Carry/borrow bit (ADDWF, ADDLW,SUBLW,SUBWF instructions) (for borrow, the polarity is reversed) 1 = A carry-out from the Most Significant bit of the result occurred 0 = No carry-out from the Most Significant bit of the result occurred Note: A subtraction is executed by adding the two's complement of the second operand. For rotate (RRF, RLF) instructions, this bit is loaded with either the high or low order bit of the source register. Legend: DS35007C-page 8 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR '1' = Bit is set '0' = Bit is cleared x = Bit is unknown 2001-2013 Microchip Technology Inc. PIC16F84A 2.3.2 OPTION REGISTER Note: The OPTION register is a readable and writable register which contains various control bits to configure the TMR0/WDT prescaler, the external INT interrupt, TMR0, and the weak pull-ups on PORTB. REGISTER 2-2: When the prescaler is assigned to the WDT (PSA = '1'), TMR0 has a 1:1 prescaler assignment. OPTION REGISTER (ADDRESS 81h) R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 RBPU INTEDG T0CS T0SE PSA PS2 PS1 PS0 bit 7 bit 0 bit 7 RBPU: PORTB Pull-up Enable bit 1 = PORTB pull-ups are disabled 0 = PORTB pull-ups are enabled by individual port latch values bit 6 INTEDG: Interrupt Edge Select bit 1 = Interrupt on rising edge of RB0/INT pin 0 = Interrupt on falling edge of RB0/INT pin bit 5 T0CS: TMR0 Clock Source Select bit 1 = Transition on RA4/T0CKI pin 0 = Internal instruction cycle clock (CLKOUT) bit 4 T0SE: TMR0 Source Edge Select bit 1 = Increment on high-to-low transition on RA4/T0CKI pin 0 = Increment on low-to-high transition on RA4/T0CKI pin bit 3 PSA: Prescaler Assignment bit 1 = Prescaler is assigned to the WDT 0 = Prescaler is assigned to the Timer0 module bit 2-0 PS2:PS0: Prescaler Rate Select bits Bit Value TMR0 Rate WDT Rate 000 001 010 011 100 101 110 111 1:2 1:4 1:8 1 : 16 1 : 32 1 : 64 1 : 128 1 : 256 1:1 1:2 1:4 1:8 1 : 16 1 : 32 1 : 64 1 : 128 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR '1' = Bit is set '0' = Bit is cleared 2001-2013 Microchip Technology Inc. x = Bit is unknown DS35007C-page 9 PIC16F84A 2.3.3 INTCON REGISTER Note: The INTCON register is a readable and writable register that contains the various enable bits for all interrupt sources. REGISTER 2-3: Interrupt flag bits are set when an interrupt condition occurs, regardless of the state of its corresponding enable bit or the global enable bit, GIE (INTCON<7>). INTCON REGISTER (ADDRESS 0Bh, 8Bh) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-x GIE EEIE T0IE INTE RBIE T0IF INTF RBIF bit 7 bit 0 bit 7 GIE: Global Interrupt Enable bit 1 = Enables all unmasked interrupts 0 = Disables all interrupts bit 6 EEIE: EE Write Complete Interrupt Enable bit 1 = Enables the EE Write Complete interrupts 0 = Disables the EE Write Complete interrupt bit 5 T0IE: TMR0 Overflow Interrupt Enable bit 1 = Enables the TMR0 interrupt 0 = Disables the TMR0 interrupt bit 4 INTE: RB0/INT External Interrupt Enable bit 1 = Enables the RB0/INT external interrupt 0 = Disables the RB0/INT external interrupt bit 3 RBIE: RB Port Change Interrupt Enable bit 1 = Enables the RB port change interrupt 0 = Disables the RB port change interrupt bit 2 T0IF: TMR0 Overflow Interrupt Flag bit 1 = TMR0 register has overflowed (must be cleared in software) 0 = TMR0 register did not overflow bit 1 INTF: RB0/INT External Interrupt Flag bit 1 = The RB0/INT external interrupt occurred (must be cleared in software) 0 = The RB0/INT external interrupt did not occur bit 0 RBIF: RB Port Change Interrupt Flag bit 1 = At least one of the RB7:RB4 pins changed state (must be cleared in software) 0 = None of the RB7:RB4 pins have changed state Legend: DS35007C-page 10 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR '1' = Bit is set '0' = Bit is cleared x = Bit is unknown 2001-2013 Microchip Technology Inc. PIC16F84A 2.4 PCL and PCLATH The program counter (PC) specifies the address of the instruction to fetch for execution. The PC is 13 bits wide. The low byte is called the PCL register. This register is readable and writable. The high byte is called the PCH register. This register contains the PC<12:8> bits and is not directly readable or writable. If the program counter (PC) is modified or a conditional test is true, the instruction requires two cycles. The second cycle is executed as a NOP. All updates to the PCH register go through the PCLATH register. 2.4.1 STACK The stack allows a combination of up to 8 program calls and interrupts to occur. The stack contains the return address from this branch in program execution. Mid-range devices have an 8 level deep x 13-bit wide hardware stack. The stack space is not part of either program or data space and the stack pointer is not readable or writable. The PC is PUSHed onto the stack when a CALL instruction is executed or an interrupt causes a branch. The stack is POPed in the event of a RETURN, RETLW or a RETFIE instruction execution. PCLATH is not modified when the stack is PUSHed or POPed. After the stack has been PUSHed eight times, the ninth push overwrites the value that was stored from the first push. The tenth push overwrites the second push (and so on). 2.5 Indirect Addressing; INDF and FSR Registers The INDF register is not a physical register. Addressing INDF actually addresses the register whose address is contained in the FSR register (FSR is a pointer). This is indirect addressing. EXAMPLE 2-1: INDIRECT ADDRESSING * * * * Register file 05 contains the value 10h Register file 06 contains the value 0Ah Load the value 05 into the FSR register A read of the INDF register will return the value of 10h * Increment the value of the FSR register by one (FSR = 06) * A read of the INDF register now will return the value of 0Ah. Reading INDF itself indirectly (FSR = 0) will produce 00h. Writing to the INDF register indirectly results in a no-operation (although STATUS bits may be affected). A simple program to clear RAM locations 20h-2Fh using indirect addressing is shown in Example 2-2. EXAMPLE 2-2: movlw movwf NEXT clrf incf btfss goto CONTINUE : HOW TO CLEAR RAM USING INDIRECT ADDRESSING 0x20 FSR INDF FSR FSR,4 NEXT ;initialize pointer ;to RAM ;clear INDF register ;inc pointer ;all done? ;NO, clear next ;YES, continue An effective 9-bit address is obtained by concatenating the 8-bit FSR register and the IRP bit (STATUS<7>), as shown in Figure 2-3. However, IRP is not used in the PIC16F84A. 2001-2013 Microchip Technology Inc. DS35007C-page 11 PIC16F84A FIGURE 2-3: DIRECT/INDIRECT ADDRESSING Indirect Addressing Direct Addressing RP1 RP0 6 From Opcode 0 IRP (2) 7 (FSR) 0 (2) Bank Select Location Select Bank Select 00 Location Select 01 00h 80h 0Bh 0Ch Addresses map back to Bank 0 Data Memory(1) 4Fh 50h 7Fh (3) (3) Bank 0 Bank 1 FFh Note 1: For memory map detail, see Figure 2-2. 2: Maintain as clear for upward compatibility with future products. 3: Not implemented. DS35007C-page 12 2001-2013 Microchip Technology Inc. PIC16F84A 3.0 DATA EEPROM MEMORY The EEPROM data memory is readable and writable during normal operation (full VDD range). This memory is not directly mapped in the register file space. Instead it is indirectly addressed through the Special Function Registers. There are four SFRs used to read and write this memory. These registers are: The EEPROM data memory allows byte read and write. A byte write automatically erases the location and writes the new data (erase before write). The EEPROM data memory is rated for high erase/write cycles. The write time is controlled by an on-chip timer. The writetime will vary with voltage and temperature as well as from chip to chip. Please refer to AC specifications for exact limits. * * * * EECON1 EECON2 (not a physically implemented register) EEDATA EEADR When the device is code protected, the CPU may continue to read and write the data EEPROM memory. The device programmer can no longer access this memory. EEDATA holds the 8-bit data for read/write, and EEADR holds the address of the EEPROM location being accessed. PIC16F84A devices have 64 bytes of data EEPROM with an address range from 0h to 3Fh. Additional information on the Data EEPROM is available in the PIC(R) Mid-Range Reference Manual (DS33023). REGISTER 3-1: EECON1 REGISTER (ADDRESS 88h) U-0 U-0 U-0 R/W-0 R/W-x R/W-0 R/S-0 R/S-0 -- -- -- EEIF WRERR WREN WR RD bit 7 bit 0 bit 7-5 Unimplemented: Read as '0' bit 4 EEIF: EEPROM Write Operation Interrupt Flag bit 1 = The write operation completed (must be cleared in software) 0 = The write operation is not complete or has not been started bit 3 WRERR: EEPROM Error Flag bit 1 = A write operation is prematurely terminated (any MCLR Reset or any WDT Reset during normal operation) 0 = The write operation completed bit 2 WREN: EEPROM Write Enable bit 1 = Allows write cycles 0 = Inhibits write to the EEPROM bit 1 WR: Write Control bit 1 = Initiates a write cycle. The bit is cleared by hardware once write is complete. The WR bit can only be set (not cleared) in software. 0 = Write cycle to the EEPROM is complete bit 0 RD: Read Control bit 1 = Initiates an EEPROM read RD is cleared in hardware. The RD bit can only be set (not cleared) in software. 0 = Does not initiate an EEPROM read Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR '1' = Bit is set '0' = Bit is cleared 2001-2013 Microchip Technology Inc. x = Bit is unknown DS35007C-page 13 PIC16F84A 3.1 Reading the EEPROM Data Memory Additionally, the WREN bit in EECON1 must be set to enable write. This mechanism prevents accidental writes to data EEPROM due to errant (unexpected) code execution (i.e., lost programs). The user should keep the WREN bit clear at all times, except when updating EEPROM. The WREN bit is not cleared by hardware. To read a data memory location, the user must write the address to the EEADR register and then set control bit RD (EECON1<0>). The data is available, in the very next cycle, in the EEDATA register; therefore, it can be read in the next instruction. EEDATA will hold this value until another read or until it is written to by the user (during a write operation). EXAMPLE 3-1: BCF MOVLW MOVWF BSF BSF BCF MOVF 3.2 After a write sequence has been initiated, clearing the WREN bit will not affect this write cycle. The WR bit will be inhibited from being set unless the WREN bit is set. At the completion of the write cycle, the WR bit is cleared in hardware and the EE Write Complete Interrupt Flag bit (EEIF) is set. The user can either enable this interrupt or poll this bit. EEIF must be cleared by software. DATA EEPROM READ STATUS, RP0 CONFIG_ADDR EEADR STATUS, RP0 EECON1, RD STATUS, RP0 EEDATA, W ; ; ; ; ; ; ; Bank 0 Address to read Bank 1 EE Read Bank 0 W = EEDATA 3.3 Depending on the application, good programming practice may dictate that the value written to the Data EEPROM should be verified (Example 3-3) to the desired value to be written. This should be used in applications where an EEPROM bit will be stressed near the specification limit. Writing to the EEPROM Data Memory To write an EEPROM data location, the user must first write the address to the EEADR register and the data to the EEDATA register. Then the user must follow a specific sequence to initiate the write for each byte. Required Sequence EXAMPLE 3-2: Generally, the EEPROM write failure will be a bit which was written as a '0', but reads back as a '1' (due to leakage off the bit). EXAMPLE 3-3: DATA EEPROM WRITE BSF BCF BSF MOVLW STATUS, RP0 INTCON, GIE EECON1, WREN 55h ; Bank 1 ; Disable INTs. ; Enable Write ; MOVWF MOVLW MOVWF BSF EECON2 AAh EECON2 EECON1,WR BSF INTCON, GIE ; ; ; ; ; ; Address WRITE VERIFY BCF STATUS,RP0 ; Bank 0 : ; Any code : ; can go here MOVF EEDATA,W ; Must be in Bank 0 BSF STATUS,RP0 ; Bank 1 Write 55h READ BSF ; YES, Read the ; value written BCF STATUS, RP0 ; Bank 0 ; ; Is the value written ; (in W reg) and ; read (in EEDATA) ; the same? ; SUBWF EEDATA, W ; BTFSS STATUS, Z ; Is difference 0? GOTO WRITE_ERR ; NO, Write error Write AAh Set WR bit begin write Enable INTs. The write will not initiate if the above sequence is not exactly followed (write 55h to EECON2, write AAh to EECON2, then set WR bit) for each byte. We strongly recommend that interrupts be disabled during this code segment. TABLE 3-1: Write Verify EECON1, RD REGISTERS/BITS ASSOCIATED WITH DATA EEPROM Name Bit 7 Bit 6 Bit 5 08h EEDATA EEPROM Data Register 09h EEADR EEPROM Address Register 88h EECON1 89h EECON2 -- -- -- Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on Power-on Reset Value on all other RESETS xxxx xxxx uuuu uuuu xxxx xxxx uuuu uuuu EEIF EEPROM Control Register 2 WRERR WREN WR RD ---0 x000 ---0 q000 ---- ---- ---- ---- Legend: x = unknown, u = unchanged, - = unimplemented, read as '0', q = value depends upon condition. Shaded cells are not used by data EEPROM. DS35007C-page 14 2001-2013 Microchip Technology Inc. PIC16F84A 4.0 I/O PORTS FIGURE 4-1: Some pins for these I/O ports are multiplexed with an alternate function for the peripheral features on the device. In general, when a peripheral is enabled, that pin may not be used as a general purpose I/O pin. Additional information on I/O ports may be found in the PIC(R) Mid-Range Reference Manual (DS33023). 4.1 Data Bus BLOCK DIAGRAM OF PINS RA3:RA0 D Q VDD WR Port Q CK P Data Latch PORTA and TRISA Registers N PORTA is a 5-bit wide, bi-directional port. The corresponding data direction register is TRISA. Setting a TRISA bit (= 1) will make the corresponding PORTA pin an input (i.e., put the corresponding output driver in a Hi-Impedance mode). Clearing a TRISA bit (= 0) will make the corresponding PORTA pin an output (i.e., put the contents of the output latch on the selected pin). Note: Pin RA4 is multiplexed with the Timer0 module clock input to become the RA4/T0CKI pin. The RA4/T0CKI pin is a Schmitt Trigger input and an open drain output. All other RA port pins have TTL input levels and full CMOS output drivers. EXAMPLE 4-1: BSF MOVLW MOVWF WR TRIS Q VSS Q CK TRIS Latch TTL Input Buffer On a Power-on Reset, these pins are configured as inputs and read as '0'. Reading the PORTA register reads the status of the pins, whereas writing to it will write to the port latch. All write operations are read-modify-write operations. Therefore, a write to a port implies that the port pins are read. This value is modified and then written to the port data latch. BCF CLRF D RD TRIS Q Initialize PORTA by clearing output data latches Select Bank 1 Value used to initialize data direction Set RA<3:0> as inputs RA4 as output TRISA<7:5> are always read as '0'. D EN RD Port Note: I/O pins have protection diodes to VDD and VSS. FIGURE 4-2: BLOCK DIAGRAM OF PIN RA4 INITIALIZING PORTA STATUS, RP0 ; PORTA ; ; ; STATUS, RP0 ; 0x0F ; ; ; TRISA ; ; ; ; I/O pin Data Bus WR Port D Q CK Q N Data Latch WR TRIS D Q CK Q RA4 pin VSS TRIS Latch Schmitt Trigger Input Buffer RD TRIS Q D EN EN RD Port TMR0 Clock Input Note: 2001-2013 Microchip Technology Inc. I/O pins have protection diodes to VDD and VSS. DS35007C-page 15 PIC16F84A TABLE 4-1: PORTA FUNCTIONS Name Bit0 Buffer Type RA0 RA1 RA2 RA3 RA4/T0CKI bit0 bit1 bit2 bit3 bit4 TTL TTL TTL TTL ST Function Input/output Input/output Input/output Input/output Input/output or external clock input for TMR0. Output is open drain type. Legend: TTL = TTL input, ST = Schmitt Trigger input TABLE 4-2: Address Name SUMMARY OF REGISTERS ASSOCIATED WITH PORTA Bit 7 Bit 6 Bit 5 Bit 4 05h PORTA -- -- -- RA4/T0CKI 85h TRISA -- -- -- TRISA4 Bit 3 Bit 2 Bit 1 Bit 0 RA3 RA2 RA1 RA0 Value on Power-on Reset Value on all other RESETS ---x xxxx ---u uuuu TRISA3 TRISA2 TRISA1 TRISA0 ---1 1111 ---1 1111 Legend: x = unknown, u = unchanged, - = unimplemented, read as '0'. Shaded cells are unimplemented, read as '0'. DS35007C-page 16 2001-2013 Microchip Technology Inc. PIC16F84A 4.2 PORTB and TRISB Registers PORTB is an 8-bit wide, bi-directional port. The corresponding data direction register is TRISB. Setting a TRISB bit (= 1) will make the corresponding PORTB pin an input (i.e., put the corresponding output driver in a Hi-Impedance mode). Clearing a TRISB bit (= 0) will make the corresponding PORTB pin an output (i.e., put the contents of the output latch on the selected pin). EXAMPLE 4-2: BCF CLRF BSF MOVLW MOVWF VDD RBPU(1) Weak P Pull-up Data Latch Data Bus D Q I/O pin(2) WR Port CK TRIS Latch D Initialize PORTB by clearing output data latches Select Bank 1 Value used to initialize data direction Set RB<3:0> as inputs RB<5:4> as outputs RB<7:6> as inputs Four of PORTB's pins, RB7:RB4, have an interrupt-onchange feature. Only pins configured as inputs can cause this interrupt to occur (i.e., any RB7:RB4 pin configured as an output is excluded from the interrupton-change comparison). The input pins (of RB7:RB4) are compared with the old value latched on the last read of PORTB. The "mismatch" outputs of RB7:RB4 are OR'ed together to generate the RB Port Change Interrupt with flag bit RBIF (INTCON<0>). This interrupt can wake the device from SLEEP. The user, in the Interrupt Service Routine, can clear the interrupt in the following manner: b) BLOCK DIAGRAM OF PINS RB7:RB4 INITIALIZING PORTB STATUS, RP0 ; PORTB ; ; ; STATUS, RP0 ; 0xCF ; ; ; TRISB ; ; ; Each of the PORTB pins has a weak internal pull-up. A single control bit can turn on all the pull-ups. This is performed by clearing bit RBPU (OPTION<7>). The weak pull-up is automatically turned off when the port pin is configured as an output. The pull-ups are disabled on a Power-on Reset. a) FIGURE 4-3: Any read or write of PORTB. This will end the mismatch condition. Clear flag bit RBIF. WR TRIS TTL Input Buffer CK RD TRIS Latch Q Q From other RB7:RB4 pins D EN RD Port Note 1: 2: TRISB = '1' enables weak pull-up (if RBPU = '0' in the OPTION_REG register). I/O pins have diode protection to VDD and VSS. FIGURE 4-4: BLOCK DIAGRAM OF PINS RB3:RB0 VDD RBPU(1) Data Bus WR Port Weak P Pull-up Data Latch D Q I/O pin(2) CK TRIS Latch D WR TRIS Q TTL Input Buffer CK RD TRIS Q RD Port D EN RB0/INT Schmitt Trigger Buffer Note 1: 2: 2001-2013 Microchip Technology Inc. D EN RD Port Set RBIF A mismatch condition will continue to set flag bit RBIF. Reading PORTB will end the mismatch condition and allow flag bit RBIF to be cleared. The interrupt-on-change feature is recommended for wake-up on key depression operation and operations where PORTB is only used for the interrupt-on-change feature. Polling of PORTB is not recommended while using the interrupt-on-change feature. Q RD Port TRISB = '1' enables weak pull-up (if RBPU = '0' in the OPTION_REG register). I/O pins have diode protection to VDD and VSS. DS35007C-page 17 PIC16F84A TABLE 4-3: PORTB FUNCTIONS Name RB0/INT Bit Buffer Type bit0 TTL/ST(1) I/O Consistency Function Input/output pin or external interrupt input. Internal software programmable weak pull-up. RB1 bit1 TTL Input/output pin. Internal software programmable weak pull-up. RB2 bit2 TTL Input/output pin. Internal software programmable weak pull-up. RB3 bit3 TTL Input/output pin. Internal software programmable weak pull-up. RB4 bit4 TTL Input/output pin (with interrupt-on-change). Internal software programmable weak pull-up. RB5 bit5 TTL Input/output pin (with interrupt-on-change). Internal software programmable weak pull-up. Input/output pin (with interrupt-on-change). RB6 bit6 TTL/ST(2) Internal software programmable weak pull-up. Serial programming clock. Input/output pin (with interrupt-on-change). RB7 bit7 TTL/ST(2) Internal software programmable weak pull-up. Serial programming data. Legend: TTL = TTL input, ST = Schmitt Trigger. Note 1: This buffer is a Schmitt Trigger input when configured as the external interrupt. 2: This buffer is a Schmitt Trigger input when used in Serial Programming mode. TABLE 4-4: Address SUMMARY OF REGISTERS ASSOCIATED WITH PORTB Name 06h PORTB 86h TRISB 81h OPTION_REG 0Bh,8Bh INTCON Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 RB7 RB6 RB5 RB4 RB3 RB2 RB1 TRISB7 TRISB6 TRISB5 TRISB4 TRISB3 TRISB2 TRISB1 Bit 0 Value on Power-on Reset Value on all other RESETS RB0/INT xxxx xxxx uuuu uuuu TRISB0 1111 1111 1111 1111 RBPU INTEDG T0CS T0SE PSA PS2 PS1 PS0 1111 1111 1111 1111 GIE EEIE T0IE INTE RBIE T0IF INTF RBIF 0000 000x 0000 000u Legend: x = unknown, u = unchanged. Shaded cells are not used by PORTB. DS35007C-page 18 2001-2013 Microchip Technology Inc. PIC16F84A 5.0 TIMER0 MODULE Additional information on external clock requirements is available in the PIC(R) Mid-Range Reference Manual, (DS33023). The Timer0 module timer/counter has the following features: * * * * * * 5.2 8-bit timer/counter Readable and writable Internal or external clock select Edge select for external clock 8-bit software programmable prescaler Interrupt-on-overflow from FFh to 00h An 8-bit counter is available as a prescaler for the Timer0 module, or as a postscaler for the Watchdog Timer, respectively (Figure 5-2). For simplicity, this counter is being referred to as "prescaler" throughout this data sheet. Note that there is only one prescaler available which is mutually exclusively shared between the Timer0 module and the Watchdog Timer. Thus, a prescaler assignment for the Timer0 module means that there is no prescaler for the Watchdog Timer, and vice-versa. Figure 5-1 is a simplified block diagram of the Timer0 module. Additional information on timer modules is available in the PIC(R) Mid-Range Reference Manual (DS33023). 5.1 The prescaler is not readable or writable. The PSA and PS2:PS0 bits (OPTION_REG<3:0>) determine the prescaler assignment and prescale ratio. Timer0 Operation Timer0 can operate as a timer or as a counter. Clearing bit PSA will assign the prescaler to the Timer0 module. When the prescaler is assigned to the Timer0 module, prescale values of 1:2, 1:4, ..., 1:256 are selectable. Timer mode is selected by clearing bit T0CS (OPTION_REG<5>). In Timer mode, the Timer0 module will increment every instruction cycle (without prescaler). If the TMR0 register is written, the increment is inhibited for the following two instruction cycles. The user can work around this by writing an adjusted value to the TMR0 register. Setting bit PSA will assign the prescaler to the Watchdog Timer (WDT). When the prescaler is assigned to the WDT, prescale values of 1:1, 1:2, ..., 1:128 are selectable. When assigned to the Timer0 module, all instructions writing to the TMR0 register (e.g., CLRF 1, MOVWF 1, BSF 1,etc.) will clear the prescaler. When assigned to WDT, a CLRWDT instruction will clear the prescaler along with the WDT. Counter mode is selected by setting bit T0CS (OPTION_REG<5>). In Counter mode, Timer0 will increment, either on every rising or falling edge of pin RA4/T0CKI. The incrementing edge is determined by the Timer0 Source Edge Select bit, T0SE (OPTION_REG<4>). Clearing bit T0SE selects the rising edge. Restrictions on the external clock input are discussed below. Note: When an external clock input is used for Timer0, it must meet certain requirements. The requirements ensure the external clock can be synchronized with the internal phase clock (TOSC). Also, there is a delay in the actual incrementing of Timer0 after synchronization. FIGURE 5-1: Prescaler Writing to TMR0 when the prescaler is assigned to Timer0 will clear the prescaler count, but will not change the prescaler assignment. TIMER0 BLOCK DIAGRAM Data Bus FOSC/4 0 PSOUT 1 1 Programmable Prescaler RA4/T0CKI pin 0 8 Sync with Internal Clocks TMR0 PSOUT (2 Cycle Delay) T0SE 3 PS2, PS1, PS0 PSA T0CS Set Interrupt Flag bit T0IF on Overflow Note 1: T0CS, T0SE, PSA, PS2:PS0 (OPTION_REG<5:0>). 2: The prescaler is shared with Watchdog Timer (refer to Figure 5-2 for detailed block diagram). 2001-2013 Microchip Technology Inc. DS35007C-page 19 PIC16F84A 5.2.1 SWITCHING PRESCALER ASSIGNMENT 5.3 The TMR0 interrupt is generated when the TMR0 register overflows from FFh to 00h. This overflow sets bit T0IF (INTCON<2>). The interrupt can be masked by clearing bit T0IE (INTCON<5>). Bit T0IF must be cleared in software by the Timer0 module Interrupt Service Routine before re-enabling this interrupt. The TMR0 interrupt cannot awaken the processor from SLEEP since the timer is shut-off during SLEEP. The prescaler assignment is fully under software control (i.e., it can be changed "on the fly" during program execution). Note: To avoid an unintended device RESET, a specific instruction sequence (shown in the PIC(R) Mid-Range Reference Manual, DS33023) must be executed when changing the prescaler assignment from Timer0 to the WDT. This sequence must be followed even if the WDT is disabled. FIGURE 5-2: Timer0 Interrupt BLOCK DIAGRAM OF THE TIMER0/WDT PRESCALER CLKOUT (= FOSC/4) Data Bus 0 RA4/T0CKI pin 8 M U X 1 M U X 0 1 SYNC 2 Cycles TMR0 reg T0SE T0CS 0 1 Watchdog Timer Set Flag bit T0IF on Overflow PSA 8-bit Prescaler M U X 8 8 - to - 1 MUX PS2:PS0 PSA 1 0 WDT Enable bit MUX PSA WDT Time-out Note: T0CS, T0SE, PSA, PS2:PS0 are (OPTION_REG<5:0>). TABLE 5-1: Address REGISTERS ASSOCIATED WITH TIMER0 Name 01h TMR0 0Bh,8Bh INTCON 81h OPTION_REG 85h TRISA Bit 7 Bit 6 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on POR, BOR xxxx xxxx uuuu uuuu T0IE INTE RBIE T0IF INTF RBIF 0000 000x 0000 000u T0CS T0SE PSA PS2 PS1 PS0 1111 1111 1111 1111 ---1 1111 ---1 1111 Bit 5 Timer0 Module Register GIE EEIE RBPU INTEDG -- -- -- PORTA Data Direction Register Value on all other RESETS Legend: x = unknown, u = unchanged, - = unimplemented locations read as '0'. Shaded cells are not used by Timer0. DS35007C-page 20 2001-2013 Microchip Technology Inc. PIC16F84A 6.0 SPECIAL FEATURES OF THE CPU the chip in RESET until the crystal oscillator is stable. The other is the Power-up Timer (PWRT), which provides a fixed delay of 72 ms (nominal) on power-up only. This design keeps the device in RESET while the power supply stabilizes. With these two timers on-chip, most applications need no external RESET circuitry. What sets a microcontroller apart from other processors are special circuits to deal with the needs of real time applications. The PIC16F84A has a host of such features intended to maximize system reliability, minimize cost through elimination of external components, provide power saving operating modes and offer code protection. These features are: SLEEP mode offers a very low current power-down mode. The user can wake-up from SLEEP through external RESET, Watchdog Timer Time-out or through an interrupt. Several oscillator options are provided to allow the part to fit the application. The RC oscillator option saves system cost while the LP crystal option saves power. A set of configuration bits are used to select the various options. * OSC Selection * RESET - Power-on Reset (POR) - Power-up Timer (PWRT) - Oscillator Start-up Timer (OST) * Interrupts * Watchdog Timer (WDT) * SLEEP * Code Protection * ID Locations * In-Circuit Serial ProgrammingTM (ICSPTM) Additional information on special features is available in the PIC(R) Mid-Range Reference Manual (DS33023). 6.1 The configuration bits can be programmed (read as '0'), or left unprogrammed (read as '1'), to select various device configurations. These bits are mapped in program memory location 2007h. The PIC16F84A has a Watchdog Timer which can be shut-off only through configuration bits. It runs off its own RC oscillator for added reliability. There are two timers that offer necessary delays on power-up. One is the Oscillator Start-up Timer (OST), intended to keep REGISTER 6-1: R/P-u CP Address 2007h is beyond the user program memory space and it belongs to the special test/configuration memory space (2000h - 3FFFh). This space can only be accessed during programming. PIC16F84A CONFIGURATION WORD R/P-u R/P-u R/P-u CP Configuration Bits CP CP R/P-u R/P-u R/P-u R/P-u R/P-u CP CP CP CP bit13 CP R/P-u CP R/P-u R/P-u PWRTE WDTE R/P-u R/P-u F0SC1 F0SC0 bit0 bit 13-4 CP: Code Protection bit 1 = Code protection disabled 0 = All program memory is code protected bit 3 PWRTE: Power-up Timer Enable bit 1 = Power-up Timer is disabled 0 = Power-up Timer is enabled bit 2 WDTE: Watchdog Timer Enable bit 1 = WDT enabled 0 = WDT disabled bit 1-0 FOSC1:FOSC0: Oscillator Selection bits 11 = RC oscillator 10 = HS oscillator 01 = XT oscillator 00 = LP oscillator 2001-2013 Microchip Technology Inc. DS35007C-page 21 PIC16F84A 6.2 Oscillator Configurations 6.2.1 FIGURE 6-2: OSCILLATOR TYPES The PIC16F84A can be operated in four different oscillator modes. The user can program two configuration bits (FOSC1 and FOSC0) to select one of these four modes: * * * * LP XT HS RC 6.2.2 EXTERNAL CLOCK INPUT OPERATION (HS, XT OR LP OSC CONFIGURATION) Low Power Crystal Crystal/Resonator High Speed Crystal/Resonator Resistor/Capacitor In XT, LP, or HS modes, a crystal or ceramic resonator is connected to the OSC1/CLKIN and OSC2/CLKOUT pins to establish oscillation (Figure 6-1). C1(1) CRYSTAL/CERAMIC RESONATOR OPERATION (HS, XT OR LP OSC CONFIGURATION) RF(3) OSC2 C2(1) TABLE 6-1: RS(2) Mode XT HS Note: To Internal Logic SLEEP PIC16FXX Note 1: See Table 6-1 for recommended values of C1 and C2. 2: A series resistor (RS) may be required for AT strip cut crystals. The PIC16F84A oscillator design requires the use of a parallel cut crystal. Use of a series cut crystal may give a frequency out of the crystal manufacturers specifications. When in XT, LP, or HS modes, the device can have an external clock source to drive the OSC1/CLKIN pin (Figure 6-2). DS35007C-page 22 OSC2 CAPACITOR SELECTION FOR CERAMIC RESONATORS Ranges Tested: OSC1 XTAL PIC16FXX Open CRYSTAL OSCILLATOR/CERAMIC RESONATORS FIGURE 6-1: OSC1 Clock from Ext. System Note: Freq OSC1/C1 OSC2/C2 455 kHz 47 - 100 pF 47 - 100 pF 2.0 MHz 15 - 33 pF 15 - 33 pF 4.0 MHz 15 - 33 pF 15 - 33 pF 15 - 33 pF 15 - 33 pF 8.0 MHz 10.0 MHz 15 - 33 pF 15 - 33 pF Recommended values of C1 and C2 are identical to the ranges tested in this table. Higher capacitance increases the stability of the oscillator, but also increases the start-up time. These values are for design guidance only. Since each resonator has its own characteristics, the user should consult the resonator manufacturer for the appropriate values of external components. When using resonators with frequencies above 3.5 MHz, the use of HS mode rather than XT mode, is recommended. HS mode may be used at any VDD for which the controller is rated. 2001-2013 Microchip Technology Inc. PIC16F84A TABLE 6-2: Mode LP XT HS Note: CAPACITOR SELECTION FOR CRYSTAL OSCILLATOR Freq OSC1/C1 OSC2/C2 32 kHz 68 - 100 pF 68 - 100 pF 200 kHz 15 - 33 pF 15 - 33 pF 100 kHz 100 - 150 pF 100 - 150 pF 2 MHz 15 - 33 pF 15 - 33 pF 4 MHz 15 - 33 pF 15 - 33 pF 4 MHz 15 - 33 pF 15 - 33 pF 20 MHz 15 - 33 pF 15 - 33 pF Higher capacitance increases the stability of the oscillator, but also increases the start-up time. These values are for design guidance only. Rs may be required in HS mode, as well as XT mode, to avoid overdriving crystals with low drive level specification. Since each crystal has its own characteristics, the user should consult the crystal manufacturer for appropriate values of external components. For VDD > 4.5V, C1 = C2 30 pF is recommended. 6.2.3 RC OSCILLATOR For timing insensitive applications, the RC device option offers additional cost savings. The RC oscillator frequency is a function of the supply voltage, the resistor (REXT) values, capacitor (CEXT) values, and the operating temperature. In addition to this, the oscillator frequency will vary from unit to unit due to normal process parameter variation. Furthermore, the difference in lead frame capacitance between package types also affects the oscillation frequency, especially for low CEXT values. The user needs to take into account variation, due to tolerance of the external R and C components. Figure 6-3 shows how an R/C combination is connected to the PIC16F84A. FIGURE 6-3: RC OSCILLATOR MODE VDD REXT CEXT PIC16FXX VSS FOSC/4 Recommended values: 2001-2013 Microchip Technology Inc. Internal Clock OSC1 OSC2/CLKOUT 5 k REXT 100 k CEXT > 20pF DS35007C-page 23 PIC16F84A 6.3 RESET The PIC16F84A differentiates between various kinds of RESET: * * * * * Power-on Reset (POR) MCLR during normal operation MCLR during SLEEP WDT Reset (during normal operation) WDT Wake-up (during SLEEP) Figure 6-4 shows a simplified block diagram of the On-Chip RESET Circuit. The MCLR Reset path has a noise filter to ignore small pulses. The electrical specifications state the pulse width requirements for the MCLR pin. FIGURE 6-4: Some registers are not affected in any RESET condition; their status is unknown on a POR and unchanged in any other RESET. Most other registers are reset to a "RESET state" on POR, MCLR or WDT Reset during normal operation and on MCLR during SLEEP. They are not affected by a WDT Reset during SLEEP, since this RESET is viewed as the resumption of normal operation. Table 6-3 gives a description of RESET conditions for the program counter (PC) and the STATUS register. Table 6-4 gives a full description of RESET states for all registers. The TO and PD bits are set or cleared differently in different RESET situations (Section 6.7). These bits are used in software to determine the nature of the RESET. SIMPLIFIED BLOCK DIAGRAM OF ON-CHIP RESET CIRCUIT External Reset MCLR SLEEP WDT Time-out Reset WDT Module VDD Rise Detect S Power-on Reset VDD OST/PWRT OST Chip_Reset 10-bit Ripple Counter R Q OSC1/ CLKIN On-Chip RC Osc(1) PWRT 10-bit Ripple Counter See Table 6-5 Enable PWRT Enable OST Note 1: This is a separate oscillator from the RC oscillator of the CLKIN pin. 2: See Table 6-5. TABLE 6-3: RESET CONDITION FOR PROGRAM COUNTER AND THE STATUS REGISTER Condition Program Counter STATUS Register Power-on Reset 000h 0001 1xxx MCLR during normal operation 000h 000u uuuu MCLR during SLEEP 000h 0001 0uuu WDT Reset (during normal operation) 000h 0000 1uuu PC + 1 uuu0 0uuu WDT Wake-up Interrupt wake-up from SLEEP PC + 1(1) uuu1 0uuu Legend: u = unchanged, x = unknown Note 1: When the wake-up is due to an interrupt and the GIE bit is set, the PC is loaded with the interrupt vector (0004h). DS35007C-page 24 2001-2013 Microchip Technology Inc. PIC16F84A TABLE 6-4: Register RESET CONDITIONS FOR ALL REGISTERS MCLR during: - normal operation - SLEEP WDT Reset during normal operation Wake-up from SLEEP: - through interrupt - through WDT Time-out Address Power-on Reset -- xxxx xxxx uuuu uuuu uuuu uuuu INDF 00h ---- ---- ---- ---- ---- ---- TMR0 01h xxxx xxxx uuuu uuuu uuuu uuuu PCL 02h 0000 0000 0000 0000 STATUS 03h 0001 1xxx 000q quuu(3) uuuq quuu(3) FSR 04h xxxx xxxx uuuu uuuu uuuu uuuu PORTA(4) 05h ---x xxxx ---u uuuu ---u uuuu PORTB(5) 06h xxxx xxxx uuuu uuuu uuuu uuuu EEDATA 08h xxxx xxxx uuuu uuuu uuuu uuuu EEADR 09h xxxx xxxx uuuu uuuu uuuu uuuu PCLATH 0Ah ---0 0000 ---0 0000 ---u uuuu INTCON 0Bh 0000 000x 0000 000u uuuu uuuu(1) INDF 80h ---- ---- ---- ---- ---- ---- OPTION_REG 81h 1111 1111 1111 1111 uuuu uuuu PCL 82h 0000 0000 0000 0000 PC + 1(2) STATUS 83h 0001 1xxx 000q quuu(3) uuuq quuu(3) FSR 84h xxxx xxxx uuuu uuuu uuuu uuuu TRISA 85h ---1 1111 ---1 1111 ---u uuuu TRISB 86h 1111 1111 1111 1111 uuuu uuuu EECON1 88h ---0 x000 ---0 q000 ---0 uuuu EECON2 89h ---- ---- ---- ---- ---- ---- PCLATH 8Ah ---0 0000 ---0 0000 ---u uuuu INTCON 8Bh 0000 000x 0000 000u uuuu uuuu(1) W PC + 1(2) Legend: u = unchanged, x = unknown, - = unimplemented bit, read as '0', q = value depends on condition Note 1: One or more bits in INTCON will be affected (to cause wake-up). 2: When the wake-up is due to an interrupt and the GIE bit is set, the PC is loaded with the interrupt vector (0004h). 3: Table 6-3 lists the RESET value for each specific condition. 4: On any device RESET, these pins are configured as inputs. 5: This is the value that will be in the port output latch. 2001-2013 Microchip Technology Inc. DS35007C-page 25 PIC16F84A 6.4 Power-on Reset (POR) A Power-on Reset pulse is generated on-chip when VDD rise is detected (in the range of 1.2V - 1.7V). To take advantage of the POR, just tie the MCLR pin directly (or through a resistor) to VDD. This will eliminate external RC components usually needed to create Power-on Reset. A minimum rise time for VDD must be met for this to operate properly. See Electrical Specifications for details. 6.6 Oscillator Start-up Timer (OST) The Oscillator Start-up Timer (OST) provides a 1024 oscillator cycle delay (from OSC1 input) after the PWRT delay ends (Figure 6-6, Figure 6-7, Figure 6-8 and Figure 6-9). This ensures the crystal oscillator or resonator has started and stabilized. The OST time-out (TOST) is invoked only for XT, LP and HS modes and only on Power-on Reset or wake-up from SLEEP. When the device starts normal operation (exits the RESET condition), device operating parameters (voltage, frequency, temperature, etc.) must be met to ensure operation. If these conditions are not met, the device must be held in RESET until the operating conditions are met. When VDD rises very slowly, it is possible that the TPWRT time-out and TOST time-out will expire before VDD has reached its final value. In this case (Figure 6-9), an external Power-on Reset circuit may be necessary (Figure 6-5). For additional information, refer to Application Note AN607, "Power-up Trouble Shooting." FIGURE 6-5: EXTERNAL POWER-ON RESET CIRCUIT (FOR SLOW VDD POWER-UP) The POR circuit does not produce an internal RESET when VDD declines. 6.5 Power-up Timer (PWRT) The Power-up Timer (PWRT) provides a fixed 72 ms nominal time-out (TPWRT) from POR (Figures 6-6 through 6-9). The Power-up Timer operates on an internal RC oscillator. The chip is kept in RESET as long as the PWRT is active. The PWRT delay allows the VDD to rise to an acceptable level (possible exception shown in Figure 6-9). A configuration bit, PWRTE, can enable/disable the PWRT. See Register 6-1 for the operation of the PWRTE bit for a particular device. The power-up time delay TPWRT will vary from chip to chip due to VDD, temperature, and process variation. See DC parameters for details. VDD VDD D R R1 MCLR C PIC16FXX Note 1: External Power-on Reset circuit is required only if VDD power-up rate is too slow. The diode D helps discharge the capacitor quickly when VDD powers down. 2: R < 40 k is recommended to make sure that voltage drop across R does not exceed 0.2V (max leakage current spec on MCLR pin is 5 A). A larger voltage drop will degrade VIH level on the MCLR pin. 3: R1 = 100 to 1 k will limit any current flowing into MCLR from external capacitor C, in the event of a MCLR pin breakdown due to ESD or EOS. DS35007C-page 26 2001-2013 Microchip Technology Inc. PIC16F84A FIGURE 6-6: TIME-OUT SEQUENCE ON POWER-UP (MCLR NOT TIED TO VDD): CASE 1 VDD MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET TIME-OUT SEQUENCE ON POWER-UP (MCLR NOT TIED TO VDD): CASE 2 FIGURE 6-7: VDD MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET FIGURE 6-8: TIME-OUT SEQUENCE ON POWER-UP (MCLR TIED TO VDD): FAST VDD RISE TIME VDD MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET 2001-2013 Microchip Technology Inc. DS35007C-page 27 PIC16F84A FIGURE 6-9: TIME-OUT SEQUENCE ON POWER-UP (MCLR TIED TO VDD): SLOW VDD RISE TIME V1 VDD MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET When VDD rises very slowly, it is possible that the TPWRT time-out and TOST time-out will expire before VDD has reached its final value. In this example, the chip will reset properly if, and only if, V1 VDD min. 6.7 Time-out Sequence and Power-down Status Bits (TO/PD) On power-up (Figures 6-6 through 6-9), the time-out sequence is as follows: 1. 2. PWRT time-out is invoked after a POR has expired. Then, the OST is activated. The total time-out will vary based on oscillator configuration and PWRTE configuration bit status. For example, in RC mode with the PWRT disabled, there will be no time-out at all. TABLE 6-5: TIME-OUT IN VARIOUS SITUATIONS Power-up Oscillator Configuration XT, HS, LP RC PWRT Enabled PWRT Disabled 72 ms + 1024TOSC 1024TOSC 72 ms -- DS35007C-page 28 Since the time-outs occur from the POR pulse, if MCLR is kept low long enough, the time-outs will expire. Then bringing MCLR high, execution will begin immediately (Figure 6-6). This is useful for testing purposes or to synchronize more than one PIC16F84A device when operating in parallel. Table 6-6 shows the significance of the TO and PD bits. Table 6-3 lists the RESET conditions for some special registers, while Table 6-4 lists the RESET conditions for all the registers. TABLE 6-6: TO PD 1 1 0 x x 0 0 1 0 0 1024TOSC 1 1 -- 1 0 Wake-up from SLEEP STATUS BITS AND THEIR SIGNIFICANCE Condition Power-on Reset Illegal, TO is set on POR Illegal, PD is set on POR WDT Reset (during normal operation) WDT Wake-up MCLR during normal operation MCLR during SLEEP or interrupt wake-up from SLEEP 2001-2013 Microchip Technology Inc. PIC16F84A 6.8 6.8.1 Interrupts The PIC16F84A has 4 sources of interrupt: * * * * External interrupt RB0/INT pin TMR0 overflow interrupt PORTB change interrupts (pins RB7:RB4) Data EEPROM write complete interrupt The interrupt control register (INTCON) records individual interrupt requests in flag bits. It also contains the individual and global interrupt enable bits. The global interrupt enable bit, GIE (INTCON<7>), enables (if set) all unmasked interrupts or disables (if cleared) all interrupts. Individual interrupts can be disabled through their corresponding enable bits in INTCON register. Bit GIE is cleared on RESET. The "return from interrupt" instruction, RETFIE, exits interrupt routine as well as sets the GIE bit, which re-enables interrupts. The RB0/INT pin interrupt, the RB port change interrupt and the TMR0 overflow interrupt flags are contained in the INTCON register. When an interrupt is responded to, the GIE bit is cleared to disable any further interrupt, the return address is pushed onto the stack and the PC is loaded with 0004h. For external interrupt events, such as the RB0/INT pin or PORTB change interrupt, the interrupt latency will be three to four instruction cycles. The exact latency depends when the interrupt event occurs. The latency is the same for both one and two cycle instructions. Once in the Interrupt Service Routine, the source(s) of the interrupt can be determined by polling the interrupt flag bits. The interrupt flag bit(s) must be cleared in software before re-enabling interrupts to avoid infinite interrupt requests. Note: Individual interrupt flag bits are set regardless of the status of their corresponding mask bit or the GIE bit. FIGURE 6-10: INT INTERRUPT External interrupt on RB0/INT pin is edge triggered: either rising if INTEDG bit (OPTION_REG<6>) is set, or falling if INTEDG bit is clear. When a valid edge appears on the RB0/INT pin, the INTF bit (INTCON<1>) is set. This interrupt can be disabled by clearing control bit INTE (INTCON<4>). Flag bit INTF must be cleared in software via the Interrupt Service Routine before re-enabling this interrupt. The INT interrupt can wake the processor from SLEEP (Section 6.11) only if the INTE bit was set prior to going into SLEEP. The status of the GIE bit decides whether the processor branches to the interrupt vector following wake-up. 6.8.2 TMR0 INTERRUPT An overflow (FFh 00h) in TMR0 will set flag bit T0IF (INTCON<2>). The interrupt can be enabled/disabled by setting/clearing enable bit T0IE (INTCON<5>) (Section 5.0). 6.8.3 PORTB INTERRUPT An input change on PORTB<7:4> sets flag bit RBIF (INTCON<0>). The interrupt can be enabled/disabled by setting/clearing enable bit RBIE (INTCON<3>) (Section 4.2). Note: 6.8.4 For a change on the I/O pin to be recognized, the pulse width must be at least TCY wide. DATA EEPROM INTERRUPT At the completion of a data EEPROM write cycle, flag bit EEIF (EECON1<4>) will be set. The interrupt can be enabled/disabled by setting/clearing enable bit EEIE (INTCON<6>) (Section 3.0). INTERRUPT LOGIC T0IF T0IE INTF INTE Wake-up (If in SLEEP mode) Interrupt to CPU RBIF RBIE EEIF EEIE GIE 2001-2013 Microchip Technology Inc. DS35007C-page 29 PIC16F84A 6.9 Context Saving During Interrupts During an interrupt, only the return PC value is saved on the stack. Typically, users wish to save key register values during an interrupt (e.g., W register and STATUS register). This is implemented in software. The code in Example 6-1 stores and restores the STATUS and W register's values. The user defined registers, W_TEMP and STATUS_TEMP are the temporary storage locations for the W and STATUS registers values. EXAMPLE 6-1: PUSH ISR POP 6.10 a) b) c) d) e) Stores the W register. Stores the STATUS register in STATUS_TEMP. Executes the Interrupt Service Routine code. Restores the STATUS (and bank select bit) register. Restores the W register. SAVING STATUS AND W REGISTERS IN RAM MOVWF SWAPF MOVWF : : : : SWAPF W_TEMP STATUS, W STATUS_TEMP MOVWF STATUS SWAPF SWAPF W_TEMP, W_TEMP, STATUS_TEMP,W F W ; ; ; : ; ; ; ; ; ; ; ; ; Copy W to TEMP register, Swap status to be saved into W Save status to STATUS_TEMP register Interrupt Service Routine should configure Bank as required Swap nibbles in STATUS_TEMP register and place result into W Move W into STATUS register (sets bank to original state) Swap nibbles in W_TEMP and place result in W_TEMP Swap nibbles in W_TEMP and place result into W Watchdog Timer (WDT) The Watchdog Timer is a free running On-Chip RC Oscillator which does not require any external components. This RC oscillator is separate from the RC oscillator of the OSC1/CLKIN pin. That means that the WDT will run even if the clock on the OSC1/CLKIN and OSC2/CLKOUT pins of the device has been stopped, for example, by execution of a SLEEP instruction. During normal operation, a WDT time-out generates a device RESET. If the device is in SLEEP mode, a WDT wake-up causes the device to wake-up and continue with normal operation. The WDT can be permanently disabled by programming configuration bit WDTE as a '0' (Section 6.1). DS35007C-page 30 Example 6-1 does the following: 6.10.1 WDT PERIOD The WDT has a nominal time-out period of 18 ms, (with no prescaler). The time-out periods vary with temperature, VDD and process variations from part to part (see DC specs). If longer time-out periods are desired, a prescaler with a division ratio of up to 1:128 can be assigned to the WDT under software control by writing to the OPTION_REG register. Thus, time-out periods up to 2.3 seconds can be realized. The CLRWDT and SLEEP instructions clear the WDT and the postscaler (if assigned to the WDT) and prevent it from timing out and generating a device RESET condition. The TO bit in the STATUS register will be cleared upon a WDT time-out. 2001-2013 Microchip Technology Inc. PIC16F84A 6.10.2 WDT PROGRAMMING CONSIDERATIONS It should also be taken into account that under worst case conditions (VDD = Min., Temperature = Max., Max. WDT Prescaler), it may take several seconds before a WDT time-out occurs. FIGURE 6-11: WATCHDOG TIMER BLOCK DIAGRAM From TMR0 Clock Source (Figure 5-2) 0 WDT Timer 1 * M Postscaler U 8 X PS2:PS0 8 - to -1 MUX PSA WDT Enable Bit * To TMR0 (Figure 5-2) 1 0 MUX PSA WDT Time-out Note: PSA and PS2:PS0 are bits in the OPTION_REG register. TABLE 6-7: Addr Name 2007h Config. bits 81h SUMMARY OF REGISTERS ASSOCIATED WITH THE WATCHDOG TIMER Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on Power-on Reset (2) (2) (2) (2) PWRTE(1) WDTE FOSC1 FOSC0 (2) INTEDG T0CS T0SE PSA PS2 PS1 PS0 OPTION_REG RBPU Value on all other RESETS 1111 1111 1111 1111 Legend: x = unknown. Shaded cells are not used by the WDT. Note 1: See Register 6-1 for operation of the PWRTE bit. 2: See Register 6-1 and Section 6.12 for operation of the code and data protection bits. 2001-2013 Microchip Technology Inc. DS35007C-page 31 PIC16F84A 6.11 6.11.2 Power-down Mode (SLEEP) A device may be powered down (SLEEP) and later powered up (wake-up from SLEEP). 6.11.1 SLEEP The Power-down mode is entered by executing the SLEEP instruction. If enabled, the Watchdog Timer is cleared (but keeps running), the PD bit (STATUS<3>) is cleared, the TO bit (STATUS<4>) is set, and the oscillator driver is turned off. The I/O ports maintain the status they had before the SLEEP instruction was executed (driving high, low, or hi-impedance). For the lowest current consumption in SLEEP mode, place all I/O pins at either VDD or VSS, with no external circuitry drawing current from the I/O pins, and disable external clocks. I/O pins that are hi-impedance inputs should be pulled high or low externally to avoid switching currents caused by floating inputs. The T0CKI input should also be at VDD or VSS. The contribution from on-chip pull-ups on PORTB should be considered. The MCLR pin must be at a logic high level (VIHMC). It should be noted that a RESET generated by a WDT time-out does not drive the MCLR pin low. FIGURE 6-12: WAKE-UP FROM SLEEP The device can wake-up from SLEEP through one of the following events: 1. 2. 3. External RESET input on MCLR pin. WDT wake-up (if WDT was enabled). Interrupt from RB0/INT pin, RB port change, or data EEPROM write complete. Peripherals cannot generate interrupts during SLEEP, since no on-chip Q clocks are present. The first event (MCLR Reset) will cause a device RESET. The two latter events are considered a continuation of program execution. The TO and PD bits can be used to determine the cause of a device RESET. The PD bit, which is set on power-up, is cleared when SLEEP is invoked. The TO bit is cleared if a WDT time-out occurred (and caused wake-up). While the SLEEP instruction is being executed, the next instruction (PC + 1) is pre-fetched. For the device to wake-up through an interrupt event, the corresponding interrupt enable bit must be set (enabled). Wake-up occurs regardless of the state of the GIE bit. If the GIE bit is clear (disabled), the device continues execution at the instruction after the SLEEP instruction. If the GIE bit is set (enabled), the device executes the instruction after the SLEEP instruction and then branches to the interrupt address (0004h). In cases where the execution of the instruction following SLEEP is not desirable, the user should have a NOP after the SLEEP instruction. WAKE-UP FROM SLEEP THROUGH INTERRUPT Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 OSC1 TOST(2) CLKOUT(4) INT pin INTF Flag (INTCON<1>) GIE bit (INTCON<7>) Interrupt Latency (Note 2) Processor in SLEEP INSTRUCTION FLOW PC PC Instruction Fetched Inst(PC) = SLEEP Instruction Inst(PC - 1) Executed Note 1: 2: 3: 4: PC+1 PC+2 PC+2 Inst(PC + 1) Inst(PC + 2) SLEEP Inst(PC + 1) PC + 2 Dummy cycle 0004h 0005h Inst(0004h) Inst(0005h) Dummy cycle Inst(0004h) XT, HS, or LP oscillator mode assumed. TOST = 1024TOSC (drawing not to scale). This delay will not be there for RC osc mode. GIE = '1' assumed. In this case after wake-up, the processor jumps to the interrupt routine. If GIE = '0', execution will continue in-line. CLKOUT is not available in these osc modes, but shown here for timing reference. DS35007C-page 32 2001-2013 Microchip Technology Inc. PIC16F84A 6.11.3 WAKE-UP USING INTERRUPTS When global interrupts are disabled (GIE cleared) and any interrupt source has both its interrupt enable bit and interrupt flag bit set, one of the following will occur: * If the interrupt occurs before the execution of a SLEEP instruction, the SLEEP instruction will complete as a NOP. Therefore, the WDT and WDT postscaler will not be cleared, the TO bit will not be set and PD bits will not be cleared. * If the interrupt occurs during or after the execution of a SLEEP instruction, the device will immediately wake-up from SLEEP. The SLEEP instruction will be completely executed before the wake-up. Therefore, the WDT and WDT postscaler will be cleared, the TO bit will be set and the PD bit will be cleared. Even if the flag bits were checked before executing a SLEEP instruction, it may be possible for flag bits to become set before the SLEEP instruction completes. To determine whether a SLEEP instruction executed, test the PD bit. If the PD bit is set, the SLEEP instruction was executed as a NOP. To ensure that the WDT is cleared, a CLRWDT instruction should be executed before a SLEEP instruction. 6.12 Program Verification/Code Protection If the code protection bit(s) have not been programmed, the on-chip program memory can be read out for verification purposes. 6.13 ID Locations Four memory locations (2000h - 2004h) are designated as ID locations to store checksum or other code identification numbers. These locations are not accessible during normal execution but are readable and writable only during program/verify. Only the four Least Significant bits of ID location are usable. 6.14 In-Circuit Serial Programming PIC16F84A microcontrollers can be serially programmed while in the end application circuit. This is simply done with two lines for clock and data, and three other lines for power, ground, and the programming voltage. Customers can manufacture boards with unprogrammed devices, and then program the microcontroller just before shipping the product, allowing the most recent firmware or custom firmware to be programmed. For complete details of Serial Programming, please refer to the In-Circuit Serial ProgrammingTM (ICSPTM) Guide, (DS30277). 2001-2013 Microchip Technology Inc. DS35007C-page 33 PIC16F84A NOTES: DS35007C-page 34 2001-2013 Microchip Technology Inc. PIC16F84A 7.0 INSTRUCTION SET SUMMARY Each PIC16CXX instruction is a 14-bit word, divided into an OPCODE which specifies the instruction type and one or more operands which further specify the operation of the instruction. The PIC16CXX instruction set summary in Table 7-2 lists byte-oriented, bit-oriented, and literal and control operations. Table 7-1 shows the opcode field descriptions. For byte-oriented instructions, 'f' represents a file register designator and 'd' represents a destination designator. The file register designator specifies which file register is to be used by the instruction. The destination designator specifies where the result of the operation is to be placed. If 'd' is zero, the result is placed in the W register. If 'd' is one, the result is placed in the file register specified in the instruction. For bit-oriented instructions, 'b' represents a bit field designator which selects the number of the bit affected by the operation, while 'f' represents the address of the file in which the bit is located. For literal and control operations, 'k' represents an eight or eleven bit constant or literal value. All instructions are executed within one single instruction cycle, unless a conditional test is true or the program counter is changed as a result of an instruction. In this case, the execution takes two instruction cycles with the second cycle executed as a NOP. One instruction cycle consists of four oscillator periods. Thus, for an oscillator frequency of 4 MHz, the normal instruction execution time is 1 s. If a conditional test is true or the program counter is changed as a result of an instruction, the instruction execution time is 2 s. Table 7-2 lists the instructions recognized by the MPASMTM Assembler. Figure 7-1 shows the general formats that the instructions can have. Note: To maintain upward compatibility with future PIC16CXX products, do not use the OPTION and TRIS instructions. All examples use the following format to represent a hexadecimal number: 0xhh where h signifies a hexadecimal digit. FIGURE 7-1: TABLE 7-1: OPCODE FIELD DESCRIPTIONS Field Description f Register file address (0x00 to 0x7F) W Working register (accumulator) b Bit address within an 8-bit file register k Literal field, constant data or label x Don't care location (= 0 or 1) The assembler will generate code with x = 0. It is the recommended form of use for compatibility with all Microchip software tools. d Destination select; d = 0: store result in W, d = 1: store result in file register f. Default is d = 1 PC Program Counter TO Time-out bit PD Power-down bit The instruction set is highly orthogonal and is grouped into three basic categories: * Byte-oriented operations * Bit-oriented operations * Literal and control operations GENERAL FORMAT FOR INSTRUCTIONS Byte-oriented file register operations 13 8 7 6 OPCODE d f (FILE #) 0 d = 0 for destination W d = 1 for destination f f = 7-bit file register address Bit-oriented file register operations 13 10 9 7 6 OPCODE b (BIT #) 0 f (FILE #) b = 3-bit bit address f = 7-bit file register address Literal and control operations General 13 8 7 OPCODE 0 k (literal) k = 8-bit immediate value CALL and GOTO instructions only 13 11 OPCODE 10 0 k (literal) k = 11-bit immediate value A description of each instruction is available in the PIC(R) Mid-Range Reference Manual (DS33023). 2001-2013 Microchip Technology Inc. DS35007C-page 35 PIC16F84A TABLE 7-2: PIC16CXXX INSTRUCTION SET Mnemonic, Operands 14-Bit Opcode Description Cycles MSb LSb Status Affected Notes BYTE-ORIENTED FILE REGISTER OPERATIONS ADDWF ANDWF CLRF CLRW COMF DECF DECFSZ INCF INCFSZ IORWF MOVF MOVWF NOP RLF RRF SUBWF SWAPF XORWF f, d f, d f f, d f, d f, d f, d f, d f, d f, d f f, d f, d f, d f, d f, d Add W and f AND W with f Clear f Clear W Complement f Decrement f Decrement f, Skip if 0 Increment f Increment f, Skip if 0 Inclusive OR W with f Move f Move W to f No Operation Rotate Left f through Carry Rotate Right f through Carry Subtract W from f Swap nibbles in f Exclusive OR W with f BCF BSF BTFSC BTFSS f, b f, b f, b f, b Bit Clear f Bit Set f Bit Test f, Skip if Clear Bit Test f, Skip if Set 1 1 1 1 1 1 1 (2) 1 1 (2) 1 1 1 1 1 1 1 1 1 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 dfff dfff lfff 0xxx dfff dfff dfff dfff dfff dfff dfff lfff 0xx0 dfff dfff dfff dfff dfff ffff ffff ffff xxxx ffff ffff ffff ffff ffff ffff ffff ffff 0000 ffff ffff ffff ffff ffff 00bb 01bb 10bb 11bb bfff bfff bfff bfff ffff ffff ffff ffff 111x 1001 0kkk 0000 1kkk 1000 00xx 0000 01xx 0000 0000 110x 1010 kkkk kkkk kkkk 0110 kkkk kkkk kkkk 0000 kkkk 0000 0110 kkkk kkkk kkkk kkkk kkkk 0100 kkkk kkkk kkkk 1001 kkkk 1000 0011 kkkk kkkk 0111 0101 0001 0001 1001 0011 1011 1010 1111 0100 1000 0000 0000 1101 1100 0010 1110 0110 C,DC,Z Z Z Z Z Z Z Z Z C C C,DC,Z Z 1,2 1,2 2 1,2 1,2 1,2,3 1,2 1,2,3 1,2 1,2 1,2 1,2 1,2 1,2 1,2 BIT-ORIENTED FILE REGISTER OPERATIONS 1 1 1 (2) 1 (2) 01 01 01 01 1,2 1,2 3 3 LITERAL AND CONTROL OPERATIONS ADDLW ANDLW CALL CLRWDT GOTO IORLW MOVLW RETFIE RETLW RETURN SLEEP SUBLW XORLW k k k k k k k k k Add literal and W AND literal with W Call subroutine Clear Watchdog Timer Go to address Inclusive OR literal with W Move literal to W Return from interrupt Return with literal in W Return from Subroutine Go into standby mode Subtract W from literal Exclusive OR literal with W 1 1 2 1 2 1 1 2 2 2 1 1 1 11 11 10 00 10 11 11 00 11 00 00 11 11 C,DC,Z Z TO,PD Z TO,PD C,DC,Z Z Note 1: When an I/O register is modified as a function of itself ( e.g., MOVF PORTB, 1), the value used will be that value present on the pins themselves. For example, if the data latch is '1' for a pin configured as input and is driven low by an external device, the data will be written back with a '0'. 2: If this instruction is executed on the TMR0 register (and, where applicable, d = 1), the prescaler will be cleared if assigned to the Timer0 Module. 3: If Program Counter (PC) is modified or a conditional test is true, the instruction requires two cycles. The second cycle is executed as a NOP. Note: Additional information on the mid-range instruction set is available in the PIC(R) Mid-Range MCU Family Reference Manual (DS33023). DS35007C-page 36 2001-2013 Microchip Technology Inc. PIC16F84A 7.1 Instruction Descriptions ADDLW Add Literal and W BCF Bit Clear f Syntax: [label] ADDLW Syntax: [label] BCF Operands: 0 f 127 0b7 k f,b Operands: 0 k 255 Operation: (W) + k (W) Status Affected: C, DC, Z Operation: 0 (f) Description: The contents of the W register are added to the eight-bit literal 'k' and the result is placed in the W register. Status Affected: None Description: Bit 'b' in register 'f' is cleared. ADDWF Add W and f BSF Bit Set f Syntax: [label] ADDWF Syntax: [label] BSF Operands: 0 f 127 d Operands: 0 f 127 0b7 Operation: (W) + (f) (destination) Operation: 1 (f) Status Affected: C, DC, Z Status Affected: None Description: Add the contents of the W register with register 'f'. If 'd' is 0, the result is stored in the W register. If 'd' is 1, the result is stored back in register 'f'. Description: Bit 'b' in register 'f' is set. ANDLW AND Literal with W BTFSS Bit Test f, Skip if Set Syntax: [label] ANDLW Syntax: [label] BTFSS f,b Operands: 0 f 127 0b<7 f,d k f,b Operands: 0 k 255 Operation: (W) .AND. (k) (W) Status Affected: Z Operation: skip if (f) = 1 Description: The contents of W register are AND'ed with the eight-bit literal 'k'. The result is placed in the W register. Status Affected: None Description: If bit 'b' in register 'f' is '0', the next instruction is executed. If bit 'b' is '1', then the next instruction is discarded and a NOP is executed instead, making this a 2TCY instruction. ANDWF AND W with f Syntax: [label] ANDWF Operands: 0 f 127 d Operation: (W) .AND. (f) (destination) Status Affected: Z Description: AND the W register with register 'f'. If 'd' is 0, the result is stored in the W register. If 'd' is 1, the result is stored back in register 'f'. 2001-2013 Microchip Technology Inc. f,d DS35007C-page 37 PIC16F84A BTFSC Bit Test, Skip if Clear CLRWDT Clear Watchdog Timer Syntax: [label] BTFSC f,b Syntax: [ label ] CLRWDT Operands: 0 f 127 0b7 Operands: None Operation: Operation: skip if (f) = 0 Status Affected: None Description: If bit 'b' in register 'f' is '1', the next instruction is executed. If bit 'b' in register 'f' is '0', the next instruction is discarded, and a NOP is executed instead, making this a 2TCY instruction. 00h WDT 0 WDT prescaler, 1 TO 1 PD Status Affected: TO, PD Description: CLRWDT instruction resets the Watchdog Timer. It also resets the prescaler of the WDT. Status bits TO and PD are set. Complement f CALL Call Subroutine COMF Syntax: [ label ] CALL k Syntax: [ label ] COMF Operands: 0 k 2047 Operands: Operation: (PC)+ 1 TOS, k PC<10:0>, (PCLATH<4:3>) PC<12:11> 0 f 127 d [0,1] Operation: (f) (destination) Status Affected: Z Description: The contents of register 'f' are complemented. If 'd' is 0, the result is stored in W. If 'd' is 1, the result is stored back in register 'f'. DECF Decrement f Syntax: [label] DECF f,d f,d Status Affected: None Description: Call Subroutine. First, return address (PC+1) is pushed onto the stack. The eleven-bit immediate address is loaded into PC bits <10:0>. The upper bits of the PC are loaded from PCLATH. CALL is a two-cycle instruction. CLRF Clear f Syntax: [label] CLRF Operands: 0 f 127 Operands: Operation: 00h (f) 1Z 0 f 127 d [0,1] Operation: (f) - 1 (destination) Status Affected: Z Status Affected: Z Description: The contents of register 'f' are cleared and the Z bit is set. Description: Decrement register 'f'. If 'd' is 0, the result is stored in the W register. If 'd' is 1, the result is stored back in register 'f'. CLRW Clear W Syntax: [ label ] CLRW Operands: None Operation: 00h (W) 1Z Status Affected: Z Description: W register is cleared. Zero bit (Z) is set. DS35007C-page 38 f 2001-2013 Microchip Technology Inc. PIC16F84A DECFSZ Decrement f, Skip if 0 INCFSZ Increment f, Skip if 0 Syntax: [ label ] DECFSZ f,d Syntax: [ label ] Operands: 0 f 127 d [0,1] Operands: 0 f 127 d [0,1] Operation: (f) - 1 (destination); skip if result = 0 Operation: (f) + 1 (destination), skip if result = 0 Status Affected: None Status Affected: None Description: The contents of register 'f' are decremented. If 'd' is 0, the result is placed in the W register. If 'd' is 1, the result is placed back in register 'f'. If the result is 1, the next instruction is executed. If the result is 0, then a NOP is executed instead, making it a 2TCY instruction. Description: The contents of register 'f' are incremented. If 'd' is 0, the result is placed in the W register. If 'd' is 1, the result is placed back in register 'f'. If the result is 1, the next instruction is executed. If the result is 0, a NOP is executed instead, making it a 2TCY instruction. GOTO Unconditional Branch IORLW Inclusive OR Literal with W Syntax: [ label ] Syntax: [ label ] Operands: 0 k 2047 Operands: 0 k 255 Operation: k PC<10:0> PCLATH<4:3> PC<12:11> Operation: (W) .OR. k (W) Status Affected: Z Status Affected: None Description: Description: GOTO is an unconditional branch. The eleven-bit immediate value is loaded into PC bits <10:0>. The upper bits of PC are loaded from PCLATH<4:3>. GOTO is a twocycle instruction. The contents of the W register are OR'ed with the eight-bit literal 'k'. The result is placed in the W register. INCF Increment f IORWF Inclusive OR W with f Syntax: [ label ] Syntax: [ label ] Operands: 0 f 127 d [0,1] Operands: 0 f 127 d [0,1] Operation: (f) + 1 (destination) Operation: (W) .OR. (f) (destination) Status Affected: Z Status Affected: Z Description: The contents of register 'f' are incremented. If 'd' is 0, the result is placed in the W register. If 'd' is 1, the result is placed back in register 'f'. Description: Inclusive OR the W register with register 'f'. If 'd' is 0, the result is placed in the W register. If 'd' is 1, the result is placed back in register 'f'. GOTO k INCF f,d 2001-2013 Microchip Technology Inc. INCFSZ f,d IORLW k IORWF f,d DS35007C-page 39 PIC16F84A MOVF Move f Syntax: [ label ] Operands: 0 f 127 d [0,1] MOVF f,d RETFIE Return from Interrupt Syntax: [ label ] RETFIE Operands: None Operation: TOS PC, 1 GIE Status Affected: None Operation: (f) (destination) Status Affected: Z Description: The contents of register f are moved to a destination dependant upon the status of d. If d = 0, destination is W register. If d = 1, the destination is file register f itself. d = 1 is useful to test a file register, since status flag Z is affected. MOVLW Move Literal to W RETLW Return with Literal in W Syntax: [ label ] Syntax: [ label ] Operands: 0 k 255 Operands: 0 k 255 Operation: k (W) Operation: Status Affected: None k (W); TOS PC Description: The eight-bit literal 'k' is loaded into W register. The don't cares will assemble as 0's. Status Affected: None Description: The W register is loaded with the eight-bit literal 'k'. The program counter is loaded from the top of the stack (the return address). This is a two-cycle instruction. RETURN Return from Subroutine Syntax: [ label ] MOVLW k RETLW k MOVWF Move W to f Syntax: [ label ] Operands: 0 f 127 Operands: None Operation: (W) (f) Operation: TOS PC Status Affected: None Status Affected: None Description: Move data from W register to register 'f'. Description: Return from subroutine. The stack is POPed and the top of the stack (TOS) is loaded into the program counter. This is a two-cycle instruction. NOP No Operation MOVWF Syntax: [ label ] Operands: None Operation: No operation Status Affected: None Description: No operation. DS35007C-page 40 f RETURN NOP 2001-2013 Microchip Technology Inc. PIC16F84A RLF Rotate Left f through Carry SUBLW Subtract W from Literal Syntax: [ label ] RLF Syntax: [ label ] SUBLW k Operands: 0 f 127 d [0,1] Operands: 0 k 255 Operation: k - (W) W) Operation: See description below Status Affected: C, DC, Z Status Affected: C Description: Description: The contents of register 'f' are rotated one bit to the left through the Carry Flag. If 'd' is 0, the result is placed in the W register. If 'd' is 1, the result is stored back in register 'f'. The W register is subtracted (2's complement method) from the eight-bit literal 'k'. The result is placed in the W register. C f,d Register f RRF Rotate Right f through Carry SUBWF Subtract W from f Syntax: [ label ] Syntax: [ label ] SUBWF f,d Operands: 0 f 127 d [0,1] Operands: 0 f 127 d [0,1] Operation: See description below Operation: (f) - (W) destination) Status Affected: C Status Affected: C, DC, Z Description: The contents of register 'f' are rotated one bit to the right through the Carry Flag. If 'd' is 0, the result is placed in the W register. If 'd' is 1, the result is placed back in register 'f'. Description: RRF f,d C Subtract (2's complement method) W register from register 'f'. If 'd' is 0, the result is stored in the W register. If 'd' is 1, the result is stored back in register 'f'. Register f SWAPF SLEEP Swap Nibbles in f Syntax: [ label ] SLEEP Syntax: [ label ] SWAPF f,d Operands: None Operands: Operation: 00h WDT, 0 WDT prescaler, 1 TO, 0 PD 0 f 127 d [0,1] Operation: (f<3:0>) (destination<7:4>), (f<7:4>) (destination<3:0>) Status Affected: None Description: The upper and lower nibbles of register 'f' are exchanged. If 'd' is 0, the result is placed in W register. If 'd' is 1, the result is placed in register 'f'. Status Affected: TO, PD Description: The power-down status bit, PD is cleared. Time-out status bit, TO is set. Watchdog Timer and its prescaler are cleared. The processor is put into SLEEP mode with the oscillator stopped. 2001-2013 Microchip Technology Inc. DS35007C-page 41 PIC16F84A XORLW Exclusive OR Literal with W XORWF Syntax: [label] Operands: 0 f 127 d [0,1] Syntax: [label] Operands: 0 k 255 Operation: (W) .XOR. k W) Status Affected: Z Operation: (W) .XOR. (f) destination) The contents of the W register are XOR'ed with the eight-bit literal 'k'. The result is placed in the W register. Status Affected: Z Description: Exclusive OR the contents of the W register with register 'f'. If 'd' is 0, the result is stored in the W register. If 'd' is 1, the result is stored back in register 'f'. Description: DS35007C-page 42 XORLW k Exclusive OR W with f XORWF f,d 2001-2013 Microchip Technology Inc. 8.0 DEVELOPMENT SUPPORT The PIC(R) microcontrollers and dsPIC(R) digital signal controllers are supported with a full range of software and hardware development tools: * Integrated Development Environment - MPLAB(R) IDE Software * Compilers/Assemblers/Linkers - MPLAB C Compiler for Various Device Families - HI-TECH C(R) for Various Device Families - MPASMTM Assembler - MPLINKTM Object Linker/ MPLIBTM Object Librarian - MPLAB Assembler/Linker/Librarian for Various Device Families * Simulators - MPLAB SIM Software Simulator * Emulators - MPLAB REAL ICETM In-Circuit Emulator * In-Circuit Debuggers - MPLAB ICD 3 - PICkitTM 3 Debug Express * Device Programmers - PICkitTM 2 Programmer - MPLAB PM3 Device Programmer * Low-Cost Demonstration/Development Boards, Evaluation Kits, and Starter Kits 8.1 MPLAB Integrated Development Environment Software The MPLAB IDE software brings an ease of software development previously unseen in the 8/16/32-bit microcontroller market. The MPLAB IDE is a Windows(R) operating system-based application that contains: * A single graphical interface to all debugging tools - Simulator - Programmer (sold separately) - In-Circuit Emulator (sold separately) - In-Circuit Debugger (sold separately) * A full-featured editor with color-coded context * A multiple project manager * Customizable data windows with direct edit of contents * High-level source code debugging * Mouse over variable inspection * Drag and drop variables from source to watch windows * Extensive on-line help * Integration of select third party tools, such as IAR C Compilers The MPLAB IDE allows you to: * Edit your source files (either C or assembly) * One-touch compile or assemble, and download to emulator and simulator tools (automatically updates all project information) * Debug using: - Source files (C or assembly) - Mixed C and assembly - Machine code MPLAB IDE supports multiple debugging tools in a single development paradigm, from the cost-effective simulators, through low-cost in-circuit debuggers, to full-featured emulators. This eliminates the learning curve when upgrading to tools with increased flexibility and power. 2001-2013 Microchip Technology Inc. DS35007C-page 43 8.2 MPLAB C Compilers for Various Device Families The MPLAB C Compiler code development systems are complete ANSI C compilers for Microchip's PIC18, PIC24 and PIC32 families of microcontrollers and the dsPIC30 and dsPIC33 families of digital signal controllers. These compilers provide powerful integration capabilities, superior code optimization and ease of use. For easy source level debugging, the compilers provide symbol information that is optimized to the MPLAB IDE debugger. 8.3 HI-TECH C for Various Device Families The HI-TECH C Compiler code development systems are complete ANSI C compilers for Microchip's PIC family of microcontrollers and the dsPIC family of digital signal controllers. These compilers provide powerful integration capabilities, omniscient code generation and ease of use. For easy source level debugging, the compilers provide symbol information that is optimized to the MPLAB IDE debugger. The compilers include a macro assembler, linker, preprocessor, and one-step driver, and can run on multiple platforms. 8.4 MPASM Assembler The MPASM Assembler is a full-featured, universal macro assembler for PIC10/12/16/18 MCUs. The MPASM Assembler generates relocatable object files for the MPLINK Object Linker, Intel(R) standard HEX files, MAP files to detail memory usage and symbol reference, absolute LST files that contain source lines and generated machine code and COFF files for debugging. The MPASM Assembler features include: 8.5 MPLINK Object Linker/ MPLIB Object Librarian The MPLINK Object Linker combines relocatable objects created by the MPASM Assembler and the MPLAB C18 C Compiler. It can link relocatable objects from precompiled libraries, using directives from a linker script. The MPLIB Object Librarian manages the creation and modification of library files of precompiled code. When a routine from a library is called from a source file, only the modules that contain that routine will be linked in with the application. This allows large libraries to be used efficiently in many different applications. The object linker/library features include: * Efficient linking of single libraries instead of many smaller files * Enhanced code maintainability by grouping related modules together * Flexible creation of libraries with easy module listing, replacement, deletion and extraction 8.6 MPLAB Assembler, Linker and Librarian for Various Device Families MPLAB Assembler produces relocatable machine code from symbolic assembly language for PIC24, PIC32 and dsPIC devices. MPLAB C Compiler uses the assembler to produce its object file. The assembler generates relocatable object files that can then be archived or linked with other relocatable object files and archives to create an executable file. Notable features of the assembler include: * * * * * * Support for the entire device instruction set Support for fixed-point and floating-point data Command line interface Rich directive set Flexible macro language MPLAB IDE compatibility * Integration into MPLAB IDE projects * User-defined macros to streamline assembly code * Conditional assembly for multi-purpose source files * Directives that allow complete control over the assembly process DS35007C-page 44 2001-2013 Microchip Technology Inc. 8.7 MPLAB SIM Software Simulator The MPLAB SIM Software Simulator allows code development in a PC-hosted environment by simulating the PIC MCUs and dsPIC(R) DSCs on an instruction level. On any given instruction, the data areas can be examined or modified and stimuli can be applied from a comprehensive stimulus controller. Registers can be logged to files for further run-time analysis. The trace buffer and logic analyzer display extend the power of the simulator to record and track program execution, actions on I/O, most peripherals and internal registers. The MPLAB SIM Software Simulator fully supports symbolic debugging using the MPLAB C Compilers, and the MPASM and MPLAB Assemblers. The software simulator offers the flexibility to develop and debug code outside of the hardware laboratory environment, making it an excellent, economical software development tool. 8.8 MPLAB REAL ICE In-Circuit Emulator System MPLAB REAL ICE In-Circuit Emulator System is Microchip's next generation high-speed emulator for Microchip Flash DSC and MCU devices. It debugs and programs PIC(R) Flash MCUs and dsPIC(R) Flash DSCs with the easy-to-use, powerful graphical user interface of the MPLAB Integrated Development Environment (IDE), included with each kit. The emulator is connected to the design engineer's PC using a high-speed USB 2.0 interface and is connected to the target with either a connector compatible with incircuit debugger systems (RJ11) or with the new highspeed, noise tolerant, Low-Voltage Differential Signal (LVDS) interconnection (CAT5). The emulator is field upgradable through future firmware downloads in MPLAB IDE. In upcoming releases of MPLAB IDE, new devices will be supported, and new features will be added. MPLAB REAL ICE offers significant advantages over competitive emulators including low-cost, full-speed emulation, run-time variable watches, trace analysis, complex breakpoints, a ruggedized probe interface and long (up to three meters) interconnection cables. 2001-2013 Microchip Technology Inc. 8.9 MPLAB ICD 3 In-Circuit Debugger System MPLAB ICD 3 In-Circuit Debugger System is Microchip's most cost effective high-speed hardware debugger/programmer for Microchip Flash Digital Signal Controller (DSC) and microcontroller (MCU) devices. It debugs and programs PIC(R) Flash microcontrollers and dsPIC(R) DSCs with the powerful, yet easyto-use graphical user interface of MPLAB Integrated Development Environment (IDE). The MPLAB ICD 3 In-Circuit Debugger probe is connected to the design engineer's PC using a high-speed USB 2.0 interface and is connected to the target with a connector compatible with the MPLAB ICD 2 or MPLAB REAL ICE systems (RJ-11). MPLAB ICD 3 supports all MPLAB ICD 2 headers. 8.10 PICkit 3 In-Circuit Debugger/ Programmer and PICkit 3 Debug Express The MPLAB PICkit 3 allows debugging and programming of PIC(R) and dsPIC(R) Flash microcontrollers at a most affordable price point using the powerful graphical user interface of the MPLAB Integrated Development Environment (IDE). The MPLAB PICkit 3 is connected to the design engineer's PC using a full speed USB interface and can be connected to the target via an Microchip debug (RJ-11) connector (compatible with MPLAB ICD 3 and MPLAB REAL ICE). The connector uses two device I/O pins and the reset line to implement in-circuit debugging and In-Circuit Serial ProgrammingTM. The PICkit 3 Debug Express include the PICkit 3, demo board and microcontroller, hookup cables and CDROM with user's guide, lessons, tutorial, compiler and MPLAB IDE software. DS35007C-page 45 8.11 PICkit 2 Development Programmer/Debugger and PICkit 2 Debug Express The PICkitTM 2 Development Programmer/Debugger is a low-cost development tool with an easy to use interface for programming and debugging Microchip's Flash families of microcontrollers. The full featured Windows(R) programming interface supports baseline (PIC10F, PIC12F5xx, PIC16F5xx), midrange (PIC12F6xx, PIC16F), PIC18F, PIC24, dsPIC30, dsPIC33, and PIC32 families of 8-bit, 16-bit, and 32-bit microcontrollers, and many Microchip Serial EEPROM products. With Microchip's powerful MPLAB Integrated Development Environment (IDE) the PICkitTM 2 enables in-circuit debugging on most PIC(R) microcontrollers. In-Circuit-Debugging runs, halts and single steps the program while the PIC microcontroller is embedded in the application. When halted at a breakpoint, the file registers can be examined and modified. The PICkit 2 Debug Express include the PICkit 2, demo board and microcontroller, hookup cables and CDROM with user's guide, lessons, tutorial, compiler and MPLAB IDE software. 8.12 MPLAB PM3 Device Programmer The MPLAB PM3 Device Programmer is a universal, CE compliant device programmer with programmable voltage verification at VDDMIN and VDDMAX for maximum reliability. It features a large LCD display (128 x 64) for menus and error messages and a modular, detachable socket assembly to support various package types. The ICSPTM cable assembly is included as a standard item. In Stand-Alone mode, the MPLAB PM3 Device Programmer can read, verify and program PIC devices without a PC connection. It can also set code protection in this mode. The MPLAB PM3 connects to the host PC via an RS-232 or USB cable. The MPLAB PM3 has high-speed communications and optimized algorithms for quick programming of large memory devices and incorporates an MMC card for file storage and data applications. DS35007C-page 46 8.13 Demonstration/Development Boards, Evaluation Kits, and Starter Kits A wide variety of demonstration, development and evaluation boards for various PIC MCUs and dsPIC DSCs allows quick application development on fully functional systems. Most boards include prototyping areas for adding custom circuitry and provide application firmware and source code for examination and modification. The boards support a variety of features, including LEDs, temperature sensors, switches, speakers, RS-232 interfaces, LCD displays, potentiometers and additional EEPROM memory. The demonstration and development boards can be used in teaching environments, for prototyping custom circuits and for learning about various microcontroller applications. In addition to the PICDEMTM and dsPICDEMTM demonstration/development board series of circuits, Microchip has a line of evaluation kits and demonstration software for analog filter design, KEELOQ(R) security ICs, CAN, IrDA(R), PowerSmart battery management, SEEVAL(R) evaluation system, Sigma-Delta ADC, flow rate sensing, plus many more. Also available are starter kits that contain everything needed to experience the specified device. This usually includes a single application and debug capability, all on one board. Check the Microchip web page (www.microchip.com) for the complete list of demonstration, development and evaluation kits. 2001-2013 Microchip Technology Inc. PIC16F84A 9.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings Ambient temperature under bias.............................................................................................................-55C to +125C Storage temperature .............................................................................................................................. -65C to +150C Voltage on any pin with respect to VSS (except VDD, MCLR, and RA4) ......................................... -0.3V to (VDD + 0.3V) Voltage on VDD with respect to VSS ........................................................................................................... -0.3 to +7.5V Voltage on MCLR with respect to VSS(1) .......................................................................................................-0.3 to +14V Voltage on RA4 with respect to VSS ........................................................................................................... -0.3 to +8.5V Total power dissipation(2) .....................................................................................................................................800 mW Maximum current out of VSS pin ...........................................................................................................................150 mA Maximum current into VDD pin ..............................................................................................................................100 mA Input clamp current, IIK (VI < 0 or VI > VDD) 20 mA Output clamp current, IOK (VO < 0 or VO > VDD) 20 mA Maximum output current sunk by any I/O pin..........................................................................................................25 mA Maximum output current sourced by any I/O pin ....................................................................................................25 mA Maximum current sunk byPORTA ..........................................................................................................................80 mA Maximum current sourced by PORTA.....................................................................................................................50 mA Maximum current sunk by PORTB........................................................................................................................150 mA Maximum current sourced by PORTB ..................................................................................................................100 mA Note 1: Voltage spikes below VSS at the MCLR pin, inducing currents greater than 80 mA, may cause latch-up. Thus, a series resistor of 50-100 should be used when applying a "low" level to the MCLR pin rather than pulling this pin directly to VSS. 2: Power dissipation is calculated as follows: Pdis = VDD x {IDD - IOH} + {(VDD-VOH) x IOH} + (VOl x IOL). NOTICE: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. 2001-2013 Microchip Technology Inc. DS35007C-page 47 PIC16F84A FIGURE 9-1: PIC16F84A-20 VOLTAGE-FREQUENCY GRAPH 6.0V 5.5V 5.0V Voltage 4.5V 4.0V 3.5V 3.0V 2.5V 2.0V 20 MHz Frequency FIGURE 9-2: PIC16LF84A-04 VOLTAGEFREQUENCY GRAPH FIGURE 9-3: PIC16F84A-04 VOLTAGEFREQUENCY GRAPH 5.5V 6.0V 5.0V 5.5V 4.5V 5.0V 4.0V 4.5V 3.5V 4.0V Voltage Voltage 6.0V 3.0V 2.5V 3.5V 3.0V 2.5V 2.0V 2.0V 4 MHz 10 MHz Frequency FMAX = (6.0 MHz/V) (VDDAPPMIN - 2.0V) + 4 MHz 4 MHz Frequency Note 1: VDDAPPMIN is the minimum voltage of the PIC(R) device in the application. 2: FMAX has a maximum frequency of 10 MHz. DS35007C-page 48 2001-2013 Microchip Technology Inc. PIC16F84A 9.1 DC Characteristics PIC16LF84A-04 (Commercial, Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C (commercial) -40C TA +85C (industrial) -40C TA +125C (extended) PIC16F84A-04 (Commercial, Industrial, Extended) PIC16F84A-20 (Commercial, Industrial, Extended) Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C (commercial) -40C TA +85C (industrial) -40C TA +125C (extended) Param Symbol No. VDD Characteristic Min Typ Max Units Conditions Supply Voltage D001 16LF84A 2.0 -- 5.5 V XT, RC, and LP osc configuration 16F84A 4.0 4.5 -- -- 5.5 5.5 V V XT, RC and LP osc configuration HS osc configuration D001 D001A D002 VDR RAM Data Retention Voltage (Note 1) 1.5 -- -- V Device in SLEEP mode D003 VPOR VDD Start Voltage to ensure internal Power-on Reset signal -- Vss -- V See section on Power-on Reset for details D004 SVDD VDD Rise Rate to ensure internal Power-on Reset signal 0.05 -- -- V/ms IDD Supply Current (Note 2) D010 16LF84A -- 1 4 mA RC and XT osc configuration (Note 4) FOSC = 2.0 MHz, VDD = 5.5V D010 16F84A -- 1.8 4.5 D010A -- 3 10 D013 -- 10 20 mA RC and XT osc configuration (Note 4) FOSC = 4.0 MHz, VDD = 5.5V mA RC and XT osc configuration (Note 4) FOSC = 4.0 MHz, VDD = 5.5V (During FLASH programming) mA HS osc configuration (PIC16F84A-20) FOSC = 20 MHz, VDD = 5.5V -- 15 45 D014 16LF84A A LP osc configuration FOSC = 32 kHz, VDD = 2.0V, WDT disabled Legend: Rows with standard voltage device data only are shaded for improved readability. Data in "Typ" column is at 5.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. NR Not rated for operation. Note 1: This is the limit to which VDD can be lowered without losing RAM data. 2: The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified. 3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS. 4: For RC osc configuration, current through REXT is not included. The current through the resistor can be estimated by the formula IR = VDD/2REXT (mA) with REXT in kOhm. 5: The current is the additional current consumed when this peripheral is enabled. This current should be added to the base IDD measurement. 2001-2013 Microchip Technology Inc. DS35007C-page 49 PIC16F84A 9.1 DC Characteristics (Continued) PIC16LF84A-04 (Commercial, Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C (commercial) -40C TA +85C (industrial) -40C TA +125C (extended) PIC16F84A-04 (Commercial, Industrial, Extended) PIC16F84A-20 (Commercial, Industrial, Extended) Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C (commercial) -40C TA +85C (industrial) -40C TA +125C (extended) Param Symbol No. IPD Characteristic Min Typ Max Units Conditions Power-down Current (Note 3) D020 16LF84A D020 16F84A-20 16F84A-04 D021A 16LF84A -- 0.4 1.0 A VDD = 2.0V, WDT disabled, industrial D021A 16F84A-20 16F84A-04 -- -- 1.5 1.0 3.5 3.0 A A VDD = 4.5V, WDT disabled, industrial VDD = 4.0V, WDT disabled, industrial D021B 16F84A-20 16F84A-04 -- -- 1.5 1.0 5.5 5.0 A A VDD = 4.5V, WDT disabled, extended VDD = 4.0V, WDT disabled, extended -- -- -- -- -- .20 3.5 3.5 4.8 4.8 16 20 28 25 30 A A A A A VDD = 2.0V, Industrial, Commercial VDD = 4.0V, Commercial VDD = 4.0V, Industrial, Extended VDD = 4.5V, Commercial VDD = 4.5V, Industrial, Extended D022 IWDT Module Differential Current (Note 5) Watchdog Timer Legend: Rows with standard voltage device data only are shaded for improved readability. Data in "Typ" column is at 5.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. NR Not rated for operation. Note 1: This is the limit to which VDD can be lowered without losing RAM data. 2: The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified. 3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS. 4: For RC osc configuration, current through REXT is not included. The current through the resistor can be estimated by the formula IR = VDD/2REXT (mA) with REXT in kOhm. 5: The current is the additional current consumed when this peripheral is enabled. This current should be added to the base IDD measurement. DS35007C-page 50 2001-2013 Microchip Technology Inc. PIC16F84A 9.2 DC Characteristics: PIC16F84A-04 (Commercial, Industrial) PIC16F84A-20 (Commercial, Industrial) PIC16LF84A-04 (Commercial, Industrial) DC Characteristics All Pins Except Power Supply Pins Param Symbol No. VIL Characteristic Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C (commercial) -40C TA +85C (industrial) Operating voltage VDD range as described in DC specifications (Section 9.1) Min Typ Max Units Conditions with TTL buffer VSS -- 0.8 V 4.5V VDD 5.5V (Note 4) VSS -- 0.16VDD V Entire range (Note 4) with Schmitt Trigger buffer VSS -- 0.2VDD V Entire range Input Low Voltage I/O ports: D030 D030A D031 D032 MCLR, RA4/T0CKI VSS -- 0.2VDD V D033 OSC1 (XT, HS and LP modes) VSS -- 0.3VDD V OSC1 (RC mode) VSS -- 0.1VDD V 2.0 0.25VDD+0.8 -- -- VDD VDD V V D034 VIH Input High Voltage I/O ports: D040 D040A with TTL buffer -- 0.8 VDD -- VDD D042 MCLR, 0.8 VDD -- VDD V D042A RA4/T0CKI 0.8 VDD -- 8.5 V D043 OSC1 (XT, HS and LP modes) 0.8 VDD -- VDD V OSC1 (RC mode) 0.9 VDD D041 (Note 1) with Schmitt Trigger buffer 4.5V VDD 5.5V (Note 4) Entire range (Note 4) Entire range (Note 1) VDD V D050 VHYS Hysteresis of Schmitt Trigger Inputs -- 0.1 -- V D070 IPURB PORTB Weak Pull-up Current 50 250 400 A VDD = 5.0V, VPIN = VSS IIL Input Leakage Current (Notes 2, 3) D043A D060 I/O ports -- -- 1 A Vss VPIN VDD, Pin at hi-impedance D061 MCLR, RA4/T0CKI -- -- 5 A Vss VPIN VDD D063 OSC1 -- -- 5 A Vss VPIN VDD, XT, HS and LP osc configuration Note 1: 2: 3: 4: Data in "Typ" column is at 5.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. In RC oscillator configuration, the OSC1 pin is a Schmitt Trigger input. Do not drive the PIC16F84A with an external clock while the device is in RC mode, or chip damage may result. The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. Negative current is defined as coming out of the pin. The user may choose the better of the two specs. 2001-2013 Microchip Technology Inc. DS35007C-page 51 PIC16F84A 9.2 DC Characteristics: PIC16F84A-04 (Commercial, Industrial) PIC16F84A-20 (Commercial, Industrial) PIC16LF84A-04 (Commercial, Industrial) (Continued) DC Characteristics All Pins Except Power Supply Pins Param Symbol No. VOL Characteristic Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C (commercial) -40C TA +85C (industrial) Operating voltage VDD range as described in DC specifications (Section 9.1) Min Typ Max Units Conditions Output Low Voltage D080 I/O ports -- -- 0.6 V IOL = 8.5 mA, VDD = 4.5V D083 OSC2/CLKOUT -- -- 0.6 V IOL = 1.6 mA, VDD = 4.5V, (RC mode only) VOH Output High Voltage D090 I/O ports (Note 3) VDD-0.7 -- -- V IOH = -3.0 mA, VDD = 4.5V D092 OSC2/CLKOUT (Note 3) VDD-0.7 -- -- V IOH = -1.3 mA, VDD = 4.5V (RC mode only) -- -- 8.5 V VOD D150 Open Drain High Voltage RA4 pin Capacitive Loading Specs on Output Pins D100 COSC2 OSC2 pin -- -- 15 pF D101 CIO All I/O pins and OSC2 (RC mode) -- -- 50 pF In XT, HS and LP modes when external clock is used to drive OSC1 Data EEPROM Memory D120 ED Endurance D121 VDRW VDD for read/write D122 TDEW Erase/Write cycle time D130 EP D131 D132 1M 10M -- VMIN -- 5.5 E/W 25C at 5V V -- 4 8 ms Endurance 1000 10K -- E/W VPR VDD for read VMIN -- 5.5 V VPEW VDD for erase/write 4.5 -- 5.5 V TPEW Erase/Write cycle time -- 4 8 ms VMIN = Minimum operating voltage Program FLASH Memory D133 Note 1: 2: 3: 4: VMIN = Minimum operating voltage Data in "Typ" column is at 5.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. In RC oscillator configuration, the OSC1 pin is a Schmitt Trigger input. Do not drive the PIC16F84A with an external clock while the device is in RC mode, or chip damage may result. The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. Negative current is defined as coming out of the pin. The user may choose the better of the two specs. DS35007C-page 52 2001-2013 Microchip Technology Inc. PIC16F84A 9.3 9.3.1 AC (Timing) Characteristics TIMING PARAMETER SYMBOLOGY The timing parameter symbols have been created following one of the following formats: 1. TppS2ppS 2. TppS T F Frequency Lowercase letters (pp) and their meanings: pp 2 to ck CLKOUT cy cycle time io I/O port inp INT pin mp MCLR Uppercase letters and their meanings: S F Fall H High I Invalid (high impedance) L Low 2001-2013 Microchip Technology Inc. T Time os, osc ost pwrt rbt t0 wdt OSC1 oscillator start-up timer power-up timer RBx pins T0CKI watchdog timer P R V Z Period Rise Valid High Impedance DS35007C-page 53 PIC16F84A 9.3.2 TIMING CONDITIONS The temperature and voltages specified in Table 9-1 apply to all timing specifications unless otherwise noted. All timings are measured between high and low measurement points as indicated in Figure 9-4. Figure 9-5 specifies the load conditions for the timing specifications. TABLE 9-1: TEMPERATURE AND VOLTAGE SPECIFICATIONS - AC AC CHARACTERISTICS FIGURE 9-4: Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial -40C TA +85C for industrial Operating voltage VDD range as described in DC specifications (Section 9.1) PARAMETER MEASUREMENT INFORMATION 0.7 VDD XTAL 0.8 VDD RC (High) 0.9 VDD (High) 0.3 VDD XTAL 0.15 VDD RC (Low) OSC1 Measurement Points FIGURE 9-5: 0.1 VDD (Low) I/O Port Measurement Points LOAD CONDITIONS Load Condition 1 Load Condition 2 VDD/2 RL CL Pin CL Pin VSS VSS RL = 464 CL = 50 pF for all pins except OSC2 15 pF for OSC2 output DS35007C-page 54 2001-2013 Microchip Technology Inc. PIC16F84A 9.3.3 TIMING DIAGRAMS AND SPECIFICATIONS FIGURE 9-6: EXTERNAL CLOCK TIMING Q4 Q1 Q3 Q2 Q4 Q1 OSC1 1 3 3 4 4 2 CLKOUT TABLE 9-2: Param No. EXTERNAL CLOCK TIMING REQUIREMENTS Sym FOSC Characteristic External CLKIN Min Typ Max Units Conditions Frequency(1) DC -- 2 MHz XT, RC osc (-04, LF) DC -- 4 MHz XT, RC osc (-04) DC -- 20 MHz HS osc (-20) DC -- 200 kHz LP osc (-04, LF) Oscillator Frequency(1) DC -- 2 MHz RC osc (-04, LF) DC -- 4 MHz RC osc (-04) 0.1 -- 2 MHz XT osc (-04, LF) 0.1 -- 4 MHz XT osc (-04) 1.0 -- 20 MHz HS osc (-20) DC -- 200 kHz LP osc (-04, LF) 1 TOSC External CLKIN Period(1) 500 -- -- ns XT, RC osc (-04, LF) 250 -- -- ns XT, RC osc (-04) 50 -- -- ns HS osc (-20) 5.0 -- -- s LP osc (-04, LF) Oscillator Period(1) 500 -- -- ns RC osc (-04, LF) 250 -- -- ns RC osc (-04) 500 -- 10,000 ns XT osc (-04, LF) 250 -- 10,000 ns XT osc (-04) 50 -- 1,000 ns HS osc (-20) 5.0 -- -- s LP osc (-04, LF) 2 TCY Instruction Cycle Time(1) 0.2 4/FOSC DC s 3 TosL, Clock in (OSC1) High or Low 60 -- -- ns XT osc (-04, LF) TosH Time 50 -- -- ns XT osc (-04) 2.0 -- -- s LP osc (-04, LF) 17.5 -- -- ns HS osc (-20) 4 TosR, Clock in (OSC1) Rise or Fall 25 -- -- ns XT osc (-04) TosF Time 50 -- -- ns LP osc (-04, LF) 7.5 -- -- ns HS osc (-20) Data in "Typ" column is at 5.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: Instruction cycle period (TCY) equals four times the input oscillator time-base period. All specified values are based on characterization data for that particular oscillator type under standard operating conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current consumption. All devices are tested to operate at "Min." values with an external clock applied to the OSC1 pin. When an external clock input is used, the "Max." cycle time limit is "DC" (no clock) for all devices. 2001-2013 Microchip Technology Inc. DS35007C-page 55 PIC16F84A FIGURE 9-7: CLKOUT AND I/O TIMING Q1 Q4 Q2 Q3 OSC1 11 10 22 23 CLKOUT 13 19 14 12 18 16 I/O Pin (Input) 15 17 I/O Pin (Output) 20, 21 All tests must be done with specified capacitive loads (Figure 9-5) 50 pF on I/O pins and CLKOUT. Note: TABLE 9-3: Param No. 10 new value old value CLKOUT AND I/O TIMING REQUIREMENTS Sym Characteristic TosH2ckL OSC1 to CLKOUT 10A 11 TosH2ckH OSC1 to CLKOUT 11A 12 TckR CLKOUT rise time TckF CLKOUT fall time 12A 13 13A Min Typ Max Units Standard -- 15 30 ns Extended (LF) -- 15 120 ns (Note 1) Standard -- 15 30 ns (Note 1) Extended (LF) -- 15 120 ns (Note 1) Standard -- 15 30 ns (Note 1) Extended (LF) -- 15 100 ns (Note 1) Standard -- 15 30 ns (Note 1) Extended (LF) -- 15 100 ns (Note 1) -- -- 0.5TCY +20 ns (Note 1) Standard 0.30TCY + 30 -- -- ns (Note 1) Extended (LF) 0.30TCY + 80 -- -- ns (Note 1) 0 -- -- ns (Note 1) -- -- 125 ns CLKOUT to Port out valid 14 TckL2ioV 15 TioV2ckH Port in valid before CLKOUT Port in hold after CLKOUT 16 TckH2ioI 17 TosH2ioV OSC1 (Q1 cycle) to Port out valid 18 TosH2ioI 10 -- -- ns 19 TioV2osH Port input valid to OSC1 (I/O in setup time) Standard -75 -- -- ns Extended (LF) -175 -- -- ns 20 TioR Port output rise time Standard -- 10 35 ns Extended (LF) -- 10 70 ns TioF Port output fall time Standard -- 10 35 ns Extended (LF) -- 10 70 ns TINP INT pin high or low time Standard 20 -- -- ns Extended (LF) 55 -- -- ns Standard TOSC -- -- ns Extended (LF) TOSC -- -- ns Extended (LF) -- -- 250 ns Standard OSC1 (Q2 cycle) to Port input invalid (I/O in hold time) Extended (LF) 10 -- -- ns 20A 21 21A 22 22A 23 TRBP 23A Standard RB7:RB4 change INT high or low time Conditions (Note 1) Data in "Typ" column is at 5.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. By design. Note 1: Measurements are taken in RC mode where CLKOUT output is 4 x TOSC. DS35007C-page 56 2001-2013 Microchip Technology Inc. PIC16F84A FIGURE 9-8: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP TIMER TIMING VDD MCLR 30 Internal POR 33 PWRT Time-out 32 OSC Time-out Internal Reset Watchdog Timer Reset 31 34 34 I/O Pins TABLE 9-4: Parameter No. RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP TIMER REQUIREMENTS Sym Characteristic Min Typ Max Units Conditions TmcL MCLR Pulse Width (low) 2 -- -- s VDD = 5.0V 31 TWDT Watchdog Timer Time-out Period (No Prescaler) 7 18 33 ms VDD = 5.0V 32 TOST Oscillation Start-up Timer Period ms TOSC = OSC1 period 33 TPWRT Power-up Timer Period 28 72 132 ms VDD = 5.0V 34 TIOZ I/O hi-impedance from MCLR Low or RESET -- -- 100 ns 30 1024TOSC Data in "Typ" column is at 5V, 25C, unless otherwise stated. These parameters are for design guidance only and are not tested. 2001-2013 Microchip Technology Inc. DS35007C-page 57 PIC16F84A FIGURE 9-9: TIMER0 CLOCK TIMINGS RA4/T0CKI 40 41 42 TABLE 9-5: TIMER0 CLOCK REQUIREMENTS Parameter Sym No. 40 41 42 Characteristic Tt0H T0CKI High Pulse Width Tt0L T0CKI Low Pulse Width Tt0P T0CKI Period No Prescaler With Prescaler No Prescaler With Prescaler Min Typ Max Units Conditions 0.5TCY + 20 -- -- ns 50 30 -- -- -- -- ns ns 0.5TCY + 20 -- -- ns 50 20 -- -- -- -- ns ns 2.0V VDD 3.0V 3.0V VDD 6.0V TCY + 40 N -- -- ns N = prescale value (2, 4, ..., 256) 2.0V VDD 3.0V 3.0V VDD 6.0V Data in "Typ" column is at 5.0V, 25C, unless otherwise stated. These parameters are for design guidance only and are not tested. DS35007C-page 58 2001-2013 Microchip Technology Inc. PIC16F84A 10.0 DC/AC CHARACTERISTIC GRAPHS The graphs provided in this section are for design guidance and are not tested. In some graphs, the data presented are outside specified operating range (i.e., outside specified VDD range). This is for information only and devices are ensured to operate properly only within the specified range. The data presented in this section is a statistical summary of data collected on units from different lots over a period of time and matrix samples. `Typical' represents the mean of the distribution at 25C. `Max' or `Min' represents (mean + 3) or (mean - 3), respectively, where is a standard deviation over the whole temperature range. 2001-2013 Microchip Technology Inc. DS35007C-page 59 PIC16F84A FIGURE 10-1: TYPICAL IDD vs. FOSC OVER VDD (HS MODE, 25C) 4.0 3.5 5.5 V 3.0 5.0 V 4.5 V IDD (mA) 2.5 2.0 4.0 V 1.5 3.5 V 1.0 3.0 V 2.5 V 0.5 2.0 V 0.0 4 6 FIGURE 10-2: 8 10 FOSC (MHz) 12 14 16 18 20 MAXIMUM IDD vs. FOSC OVER VDD (HS MODE, -40 TO +125C) 5.0 4.5 5.5 V 4.0 5.0 V 3.5 4.5 V IDD (mA) 3.0 2.5 2.0 4.0 V 1.5 3.5 V 3.0 V 1.0 2.5 V 0.5 2.0 V 0.0 4 6 8 10 12 14 16 18 20 FOSC (MHz) DS35007C-page 60 (c) 2001-2013 Microchip Technology Inc. PIC16F84A FIGURE 10-3: TYPICAL IDD vs. FOSC OVER VDD (XT MODE, 25C) 1.0 0.9 0.8 5.5 V 0.7 5.0 V IDD (mA) 0.6 4.5 V 0.5 4.0 V 0.4 3.5 V 0.3 3.0 V 2.5 V 0.2 2.0 V 0.1 0.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 FOSC (MHz) FIGURE 10-4: MAXIMUM IDD vs. FOSC OVER VDD (XT MODE, -40 TO +125C) 1.0 0.9 5.5 V 0.8 5.0 V 0.7 4.5 V IDD (mA) 0.6 4.0 V 0.5 3.5 V 0.4 3.0 V 0.3 2.5 V 0.2 2.0 V 0.1 0.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 FOSC (MHz) 2001-2013 Microchip Technology Inc. DS35007C-page 61 PIC16F84A FIGURE 10-5: TYPICAL IDD vs. FOSC OVER VDD (LP MODE, 25C) 80 70 5.5 V 5.0 V 60 4.5 V 50 IDD (A) 4.0 V 40 3.5 V 3.0 V 30 2.5 V 20 2.0 V 10 0 25 50 75 100 125 150 175 200 FOSC (kHz) FIGURE 10-6: MAXIMUM IDD vs. FOSC OVER VDD (LP MODE, -40 TO +125C) 250 5.5 V 200 5.0 V IDD (A) 150 4.5 V 100 4.0 V 3.5 V 3.0 V 50 2.5 V 2.0 V 0 25 50 75 100 125 150 175 200 FOSC (kHz) DS35007C-page 62 (c) 2001-2013 Microchip Technology Inc. PIC16F84A FIGURE 10-7: AVERAGE FOSC vs. VDD FOR R (RC MODE, C = 22 pF, 25C) 16.0 3.3 k 14.0 12.0 5.1 k Freq (MHz) 10.0 8.0 10 k 6.0 4.0 2.0 100 k 0.0 2.0 FIGURE 10-8: 2.5 3.0 3.5 VDD (V) 4.0 4.5 5.0 5.5 AVERAGE FOSC vs. VDD FOR R (RC MODE, C = 100 pF, 25C) 2000 1800 3.3 k 1600 1400 5.1 k Freq (KHz) 1200 1000 800 10 k 600 400 200 100 k 0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 VDD (V) 2001-2013 Microchip Technology Inc. DS35007C-page 63 PIC16F84A FIGURE 10-9: AVERAGE FOSC vs. VDD FOR R (RC MODE, C = 300 pF, 25C) 900 800 3.3 k 700 600 Freq (KHz) 5.1 k 500 400 10 k 300 200 100 100 k 0 2.0 2.5 FIGURE 10-10: 3.0 3.5 VDD (V) 4.0 4.5 5.0 5.5 IPD vs. VDD (SLEEP MODE, ALL PERIPHERALS DISABLED) Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to +125C) Minimum: mean - 3 (-40C to +125C) 10.0 Max IPD (A) 1.0 Typ 0.1 0.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 VDD (V) DS35007C-page 64 (c) 2001-2013 Microchip Technology Inc. PIC16F84A FIGURE 10-11: IPD vs. VDD (WDT MODE) 15 Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to +125C) Minimum: mean - 3 (-40C to +125C) 14 13 12 11 10 9 IPD (A) Max 8 7 6 5 Typ 4 3 2 1 0 2.0 2.5 FIGURE 10-12: 3.0 3.5 VDD (V) 4.0 4.5 5.0 5.5 TYPICAL, MINIMUM, AND MAXIMUM WDT PERIOD vs. VDD OVER TEMP 60 50 WDT Period (ms) 40 Max 30 Typ 20 Min 10 Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to +125C) Minimum: mean - 3 (-40C to +125C) 0 2.0 2.5 2001-2013 Microchip Technology Inc. 3.0 3.5 VDD (V) 4.0 4.5 5.0 5.5 DS35007C-page 65 PIC16F84A FIGURE 10-13: TYPICAL, MINIMUM AND MAXIMUM VOH vs. IOH (VDD = 5V, -40C TO +125C) 5.0 4.5 Ma 4.0 Typ 3.5 VOH (V) 3.0 2.5 Min 2.0 1.5 1.0 Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to +125C) Minimum: mean - 3 (-40C to +125C) 0.5 0.0 0.0 FIGURE 10-14: 2.5 5.0 7.5 10.0 IOH (mA) 12.5 15.0 17.5 20.0 22.5 25.0 TYPICAL, MINIMUM AND MAXIMUM VOH vs. IOH (VDD = 3V, -40C TO +125C) 3.0 2.5 Max 2.0 VOH (V) Typ 1.5 Min 1.0 0.5 Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to +125C) Minimum: mean - 3 (-40C to +125C) 0.0 0 DS35007C-page 66 5 10 IOH (mA) 15 20 25 (c) 2001-2013 Microchip Technology Inc. PIC16F84A FIGURE 10-15: TYPICAL, MINIMUM AND MAXIMUM VOL vs. IOL (VDD = 5V, -40C TO +125C) 1.0 Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to +125C) Minimum: mean - 3 (-40C to +125C) 0.9 Max 0.8 0.7 VOL (V) 0.6 Typ 0.5 Min 0.4 0.3 0.2 0.1 0.0 0 5 10 15 20 25 IOL (mA) FIGURE 10-16: TYPICAL, MINIMUM AND MAXIMUM VOL vs. IOL (VDD = 3V, -40C TO +125C) 1.8 Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to +125C) Minimum: mean - 3 (-40C to +125C) 1.6 1.4 Max 1.2 VOL (V) 1.0 0.8 Typ 0.6 Min 0.4 0.2 0.0 0.0 2.5 5.0 2001-2013 Microchip Technology Inc. 7.5 10.0 12.5 IOL (mA) 15.0 17.5 20.0 22.5 25.0 DS35007C-page 67 PIC16F84A FIGURE 10-17: MINIMUM AND MAXIMUM VIN vs. VDD, (TTL INPUT, -40C TO +125C) 2.00 Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to +125C) Minimum: mean - 3 (-40C to +125C) 1.75 VTH 1.50 VTH VIN (V) 1.25 VTH 1.00 0.75 0.50 0.25 0.00 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 VDD (V) FIGURE 10-18: MINIMUM AND MAXIMUM VIN vs. VDD (ST INPUT, -40C TO +125C) 3.50 Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to +125C) Minimum: mean - 3 (-40C to +125C) 3.25 VIH Typ VIH Max 3.00 2.75 2.50 VIH Min VIN (V) 2.25 VIL Typ VIL Max 2.00 1.75 1.50 1.25 1.00 VIL Min 0.75 0.50 2.0 DS35007C-page 68 2.5 3.0 3.5 VDD (V) 4.0 4.5 5.0 5.5 (c) 2001-2013 Microchip Technology Inc. PIC16F84A 11.0 PACKAGING INFORMATION 11.1 Package Marking Information 18-Lead PDIP (300 mil) Example PIC16F84A-04I/P e3 0110017 18-Lead SOIC (7.50 mm) Example PIC16F84A-04 /SO e3 0110017 20-Lead SSOP (5.30 mm) Example PIC16F84A20/SS e3 0110017 Legend: XX...X Y YY WW NNN e3 * Note: Customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week `01') Alphanumeric traceability code Pb-free JEDEC designator for Matte Tin (Sn) This package is Pb-free. The Pb-free JEDEC designator ( e3 ) can be found on the outer packaging for this package. In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. 2001-2013 Microchip Technology Inc. DS35007C-page 69 PIC16F84A /HDG3ODVWLF'XDO,Q/LQH 3 PLO%RG\>3',3@ 1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW KWWSZZZPLFURFKLSFRPSDFNDJLQJ N NOTE 1 E1 1 2 3 D E A2 A L c A1 b1 b e e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page 70 2001-2013 Microchip Technology Inc. PIC16F84A Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2001-2013 Microchip Technology Inc. DS35007C-page 71 PIC16F84A Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS35007C-page 72 2001-2013 Microchip Technology Inc. PIC16F84A Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2001-2013 Microchip Technology Inc. DS35007C-page 73 PIC16F84A /HDG3ODVWLF6KULQN6PDOO2XWOLQH 66 PP%RG\>6623@ 1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW KWWSZZZPLFURFKLSFRPSDFNDJLQJ D N E E1 NOTE 1 1 2 e b c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page 74 2001-2013 Microchip Technology Inc. PIC16F84A Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2001-2013 Microchip Technology Inc. DS35007C-page 75 PIC16F84A NOTES: DS35007C-page 76 2001-2013 Microchip Technology Inc. PIC16F84A APPENDIX A: REVISION HISTORY Version Date Revision Description A 9/1998 This is a new data sheet. However, the devices described in this data sheet are the upgrades to the devices found in the PIC16F8X Data Sheet, DS30430. B 05/2001 Added DC and AC Characteristics Graphs and Tables to Section 10. C 11/2011 Updated the "Packaging Information" section. 2001-2013 Microchip Technology Inc. DS35007C-page 77 PIC16F84A APPENDIX B: CONVERSION CONSIDERATIONS Considerations for converting from one PIC16X8X device to another are listed in Table 1. TABLE 1: CONVERSION CONSIDERATIONS - PIC16C84, PIC16F83/F84, PIC16CR83/CR84, PIC16F84A Difference PIC16C84 PIC16CR83/ CR84 PIC16F83/F84 PIC16F84A Program Memory Size 1K x 14 512 x 14 / 1K x 14 512 x 14 / 1K x 14 1K x 14 Data Memory Size 36 x 8 36 x 8 / 68 x 8 36 x 8 / 68 x 8 68 x 8 Voltage Range 2.0V - 6.0V (-40C to +85C) 2.0V - 6.0V (-40C to +85C) 2.0V - 6.0V (-40C to +85C) 2.0V - 5.5V (-40C to +125C) 10 MHz 10 MHz 20 MHz Maximum Operating Fre- 10 MHz quency Supply Current (IDD). See parameter # D014 in the electrical specs for more detail. IDD (typ) = 60 A IDD (max) = 400 A (LP osc, FOSC = 32 kHz, VDD = 2.0V, WDT disabled) IDD (typ) = 15 A IDD (max) = 45 A (LP osc, FOSC = 32 kHz, VDD = 2.0V, WDT disabled) IDD (typ) = 15 A IDD (max) = 45 A (LP osc, FOSC = 32 kHz, VDD = 2.0V, WDT disabled) IDD (typ) = 15 A IDD (max) = 45 A (LP osc, FOSC = 32 kHz, VDD = 2.0V, WDT disabled) Power-down Current (IPD). See parameters # D020, D021, and D021A in the electrical specs for more detail. IPD (typ) = 26 A IPD (max) = 100 A (VDD = 2.0V, WDT disabled, industrial) IPD (typ) = 0.4 A IPD (max) = 9 A (VDD = 2.0V, WDT disabled, industrial) IPD (typ) = 0.4 A IPD (max) = 6 A (VDD = 2.0V, WDT disabled, industrial) IPD (typ) = 0.4 A IPD (max) = 1 A (VDD = 2.0V, WDT disabled, industrial) Input Low Voltage (VIL). VIL (max) = 0.2VDD See parameters # D032 (OSC1, RC mode) and D034 in the electrical specs for more detail. VIL (max) = 0.1VDD (OSC1, RC mode) VIL (max) = 0.1VDD (OSC1, RC mode) VIL (max) = 0.1VDD (OSC1, RC mode) Input High Voltage (VIH). VIH (min) = 0.36VDD See parameter # D040 in (I/O Ports with TTL, 4.5V VDD 5.5V) the electrical specs for more detail. VIH (min) = 2.4V (I/O Ports with TTL, 4.5V VDD 5.5V) VIH (min) = 2.4V (I/O Ports with TTL, 4.5V VDD 5.5V) VIH (min) = 2.4V (I/O Ports with TTL, 4.5V VDD 5.5V) Data EEPROM Memory TDEW (typ) = 10 ms Erase/Write cycle time TDEW (max) = 20 ms (TDEW). See parameter # D122 in the electrical specs for more detail. TDEW (typ) = 10 ms TDEW (max) = 20 ms TDEW (typ) = 10 ms TDEW (max) = 20 ms TDEW (typ) = 4 ms TDEW (max) = 8 ms Port Output Rise/Fall time (TioR, TioF). See parameters #20, 20A, 21, and 21A in the electrical specs for more detail. TioR, TioF (max) = 35 ns (C84) TioR, TioF (max) = 70 ns (LC84) TioR, TioF (max) = 35 ns (C84) TioR, TioF (max) = 70 ns (LC84) TioR, TioF (max) = 35 ns (C84) TioR, TioF (max) = 70 ns (LC84) Yes Yes Yes PORTA and crystal oscil- For crystal oscillator con- N/A lator values less than figurations operating 500 kHz below 500 kHz, the device may generate a spurious internal Q-clock when PORTA<0> switches state. N/A N/A RB0/INT pin TTL/ST* (*Schmitt Trigger) TTL/ST* (*Schmitt Trigger) TioR, TioF (max) = 25 ns (C84) TioR, TioF (max) = 60 ns (LC84) MCLR on-chip filter. See No parameter #30 in the electrical specs for more detail. DS35007C-page 78 TTL TTL/ST* (*Schmitt Trigger) 2001-2013 Microchip Technology Inc. PIC16F84A TABLE 1: CONVERSION CONSIDERATIONS - PIC16C84, PIC16F83/F84, PIC16CR83/CR84, PIC16F84A (CONTINUED) Difference PIC16C84 PIC16CR83/ CR84 PIC16F83/F84 PIC16F84A EEADR<7:6> and IDD N/A It is recommended that the EEADR<7:6> bits be cleared. When either of these bits is set, the maximum IDD for the device is higher than when both are cleared. N/A N/A The polarity of the PWRTE bit PWRTE PWRTE PWRTE PWRTE Recommended value of REXT for RC oscillator circuits REXT = 3k - 100k REXT = 5k - 100k REXT = 5k - 100k REXT = 3k - 100k GIE bit unintentional enable If an interrupt occurs while N/A the Global Interrupt Enable (GIE) bit is being cleared, the GIE bit may unintentionally be reenabled by the user's Interrupt Service Routine (the RETFIE instruction). N/A N/A Packages PDIP, SOIC PDIP, SOIC PDIP, SOIC PDIP, SOIC, SSOP Open Drain High Voltage (VOD) 14V 12V 12V 8.5V 2001-2013 Microchip Technology Inc. DS35007C-page 79 PIC16F84A APPENDIX C: MIGRATION FROM BASELINE TO MID-RANGE DEVICES To convert code written for PIC16C5X to PIC16F84A, the user should take the following steps: 1. This section discusses how to migrate from a baseline device (i.e., PIC16C5X) to a mid-range device (i.e., PIC16CXXX). 2. The following is the list of feature improvements over the PIC16C5X microcontroller family: 3. 1. 4. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Instruction word length is increased to 14-bits. This allows larger page sizes, both in program memory (2K now as opposed to 512K before) and the register file (128 bytes now versus 32 bytes before). A PC latch register (PCLATH) is added to handle program memory paging. PA2, PA1 and PA0 bits are removed from the STATUS register and placed in the OPTION register. Data memory paging is redefined slightly. The STATUS register is modified. Four new instructions have been added: RETURN, RETFIE, ADDLW, and SUBLW. Two instructions, TRIS and OPTION, are being phased out, although they are kept for compatibility with PIC16C5X. OPTION and TRIS registers are made addressable. Interrupt capability is added. Interrupt vector is at 0004h. Stack size is increased to eight-deep. RESET vector is changed to 0000h. RESET of all registers is revisited. Five different RESET (and wake-up) types are recognized. Registers are reset differently. Wake-up from SLEEP through interrupt is added. Two separate timers, the Oscillator Start-up Timer (OST) and Power-up Timer (PWRT), are included for more reliable power-up. These timers are invoked selectively to avoid unnecessary delays on power-up and wake-up. PORTB has weak pull-ups and interrupt-onchange features. T0CKI pin is also a port pin (RA4/T0CKI). FSR is a full 8-bit register. "In system programming" is made possible. The user can program PIC16CXX devices using only five pins: VDD, VSS, VPP, RB6 (clock) and RB7 (data in/out). DS35007C-page 80 5. Remove any program memory page select operations (PA2, PA1, PA0 bits) for CALL, GOTO. Revisit any computed jump operations (write to PC or add to PC, etc.) to make sure page bits are set properly under the new scheme. Eliminate any data memory page switching. Redefine data variables for reallocation. Verify all writes to STATUS, OPTION, and FSR registers since these have changed. Change RESET vector to 0000h. 2001-2013 Microchip Technology Inc. PIC16F84A INDEX A Absolute Maximum Ratings ................................................ 47 AC (Timing) Characteristics ................................................ 53 Architecture, Block Diagram ................................................. 3 Assembler MPASM Assembler..................................................... 44 B Banking, Data Memory ......................................................... 6 Block Diagrams Crystal/Ceramic Resonator Operation ........................ 22 External Clock Input Operation ................................... 22 External Power-on Reset Circuit................................. 26 Interrupt Logic ............................................................. 29 On-chip Reset ............................................................. 24 PIC16F84A ................................................................... 3 PORTA RA3:RA0 Pins ..................................................... 15 RA4 Pins ............................................................. 15 PORTB RB3:RB0 Pins ..................................................... 17 RB7:RB4 Pins ..................................................... 17 RC Oscillator Mode..................................................... 23 Timer0......................................................................... 19 Timer0/WDT Prescaler ............................................... 20 Watchdog Timer (WDT) .............................................. 31 C C (Carry) bit .......................................................................... 8 C Compilers MPLAB C18 ................................................................ 44 CLKIN Pin ............................................................................. 4 CLKOUT Pin ......................................................................... 4 Code Examples Clearing RAM Using Indirect Addressing.................... 11 Data EEPOM Write Verify........................................... 14 Indirect Addressing ..................................................... 11 Initializing PORTA....................................................... 15 Initializing PORTB....................................................... 17 Reading Data EEPROM ............................................. 14 Saving STATUS and W Registers in RAM ................. 30 Writing to Data EEPROM............................................ 14 Code Protection ........................................................... 21, 33 Configuration Bits................................................................ 21 Configuration Word ............................................................. 21 Conversion Considerations ................................................. 78 Customer Change Notification Service ............................... 85 Customer Notification Service............................................. 85 Customer Support ............................................................... 85 D Data EEPROM Memory ...................................................... 13 Associated Registers .................................................. 14 EEADR Register ..............................................7, 13, 25 EECON1 Register............................................7, 13, 25 EECON2 Register............................................7, 13, 25 EEDATA Register ............................................7, 13, 25 Write Complete Enable (EEIE Bit) .............................. 29 Write Complete Flag (EEIF Bit)................................... 29 Data EEPROM Write Complete .......................................... 29 Data Memory ........................................................................ 6 Bank Select (RP0 Bit) ................................................... 6 Banking ......................................................................... 6 DC bit .................................................................................... 8 2001-2013 Microchip Technology Inc. DC Characteristics........................................................49, 51 Development Support ......................................................... 43 Device Overview................................................................... 3 E EECON1 Register EEIF Bit ...................................................................... 29 Electrical Characteristics .................................................... 47 Load Conditions.......................................................... 54 Parameter Measurement Information......................... 54 PIC16F84A-04 Voltage-Frequency Graph ................. 48 PIC16F84A-20 Voltage-Frequency Graph ................. 48 PIC16LF84A-04 Voltage-Frequency Graph ............... 48 Temperature and Voltage Specifications - AC ........... 54 Endurance ............................................................................ 1 Errata .................................................................................... 2 External Clock Input (RA4/T0CKI). See Timer0 External Interrupt Input (RB0/INT). See Interrupt Sources External Power-on Reset Circuit......................................... 26 F Firmware Instructions ......................................................... 35 I I/O Ports ............................................................................. 15 ID Locations..................................................................21, 33 In-Circuit Serial Programming (ICSP)...........................21, 33 INDF Register ....................................................................... 7 Indirect Addressing ............................................................. 11 FSR Register .............................................. 6, 7, 11, 25 INDF Register.................................................. 7, 11, 25 Instruction Format............................................................... 35 Instruction Set..................................................................... 35 ADDLW....................................................................... 37 ADDWF ...................................................................... 37 ANDLW....................................................................... 37 ANDWF ...................................................................... 37 BCF ............................................................................ 37 BSF............................................................................. 37 BTFSC........................................................................ 38 BTFSS ........................................................................ 37 CALL........................................................................... 38 CLRF .......................................................................... 38 CLRW ......................................................................... 38 CLRWDT .................................................................... 38 COMF ......................................................................... 38 DECF.......................................................................... 38 DECFSZ ..................................................................... 39 GOTO ......................................................................... 39 INCF ........................................................................... 39 INCFSZ....................................................................... 39 IORLW ........................................................................ 39 IORWF........................................................................ 39 MOVF ......................................................................... 40 MOVLW ...................................................................... 40 MOVWF...................................................................... 40 NOP............................................................................ 40 RETFIE....................................................................... 40 RETLW ....................................................................... 40 RETURN..................................................................... 40 RLF............................................................................. 41 RRF ............................................................................ 41 SLEEP ........................................................................ 41 SUBLW....................................................................... 41 DS35007C-page 81 PIC16F84A SUBWF ....................................................................... 41 SWAPF ....................................................................... 41 XORLW ....................................................................... 42 XORWF....................................................................... 42 Summary Table........................................................... 36 INT Interrupt (RB0/INT)....................................................... 29 INTCON Register .................................7, 10, 18, 20, 25, 29 EEIE Bit....................................................................... 29 GIE Bit.................................................................. 10, 29 INTE Bit................................................................ 10, 29 INTF Bit ................................................................ 10, 29 PEIE Bit....................................................................... 10 RBIE Bit ............................................................... 10, 29 RBIF Bit..........................................................10, 17, 29 T0IE Bit ................................................................ 10, 29 T0IF Bit ..........................................................10, 20, 29 Internet Address.................................................................. 85 Interrupt Sources.......................................................... 21, 29 Block Diagram............................................................. 29 Data EEPROM Write Complete ........................... 29, 32 Interrupt-on-Change (RB7:RB4) ............... 4, 17, 29, 32 RB0/INT Pin, External ............................... 4, 18, 29, 32 TMR0 Overflow .................................................... 20, 29 Interrupts, Context Saving During ....................................... 30 Interrupts, Enable Bits Data EEPROM Write Complete Enable (EEIE Bit) ..... 29 Global Interrupt Enable (GIE Bit) ................................ 10 Interrupt-on-Change (RB7:RB4) Enable (RBIE Bit) .... 10 Peripheral Interrupt Enable (PEIE Bit) ........................ 10 RB0/INT Enable (INTE Bit) ......................................... 10 TMR0 Overflow Enable (T0IE Bit)............................... 10 Interrupts, Flag Bits ............................................................. 29 Data EEPROM Write Complete Flag (EEIF Bit).......... 29 Interrupt-on-Change (RB7:RB4) Flag (RBIF Bit) ........ 10 RB0/INT Flag (INTF Bit).............................................. 10 TMR0 Overflow Flag (T0IF Bit) ................................... 10 IRP bit ................................................................................... 8 M Master Clear (MCLR) MCLR Pin...................................................................... 4 MCLR Reset, Normal Operation ................................. 24 MCLR Reset, SLEEP ........................................... 24, 32 Memory Organization............................................................ 5 Data EEPROM Memory .............................................. 13 Data Memory ................................................................ 6 Program Memory .......................................................... 5 Microchip Internet Web Site ................................................ 85 Migration from Baseline to Mid-Range Devices .................. 80 MPLAB ASM30 Assembler, Linker, Librarian ..................... 44 MPLAB Integrated Development Environment Software .... 43 MPLAB PM3 Device Programmer....................................... 46 MPLAB REAL ICE In-Circuit Emulator System................... 45 MPLINK Object Linker/MPLIB Object Librarian .................. 44 O OPCODE Field Descriptions ............................................... 35 OPTION Register .................................................................. 9 INTEDG Bit ................................................................... 9 PS2:PS0 Bits ................................................................ 9 PSA Bit.......................................................................... 9 RBPU Bit ....................................................................... 9 T0CS Bit........................................................................ 9 T0SE Bit ........................................................................ 9 DS35007C-page 82 OPTION_REG Register.................................... 7, 18, 20, 25 INTEDG Bit ................................................................. 29 PS2:PS0 Bits .............................................................. 19 PSA Bit ....................................................................... 19 OSC1 Pin.............................................................................. 4 OSC2 Pin.............................................................................. 4 Oscillator Configuration ................................................21, 22 Block Diagram ......................................................22, 23 Capacitor Selection for Ceramic Resonators.............. 22 Capacitor Selection for Crystal Oscillator ................... 23 Crystal Oscillator/Ceramic Resonators....................... 22 HS.........................................................................22, 28 LP .........................................................................22, 28 Oscillator Types .......................................................... 22 RC ................................................................. 22, 23, 28 XT .........................................................................22, 28 P Packaging Information ........................................................ 69 Marking ....................................................................... 69 PD bit .................................................................................... 8 Pinout Descriptions............................................................... 4 Pointer, FSR ....................................................................... 11 POR. See Power-on Reset PORTA ...........................................................................4, 15 Associated Registers .................................................. 16 Functions .................................................................... 16 Initializing .................................................................... 15 PORTA Register ....................................... 7, 15, 16, 25 RA3:RA0 Block Diagram ............................................ 15 RA4 Block Diagram .................................................... 15 RA4/T0CKI Pin ................................................ 4, 15, 19 TRISA Register...................................7, 15, 16, 20, 25 PORTB ...........................................................................4, 17 Associated Registers .................................................. 18 Functions .................................................................... 18 Initializing .................................................................... 17 PORTB Register ....................................... 7, 17, 18, 25 Pull-up Enable Bit (RBPU Bit)....................................... 9 RB0/INT Edge Select (INTEDG Bit) ............................. 9 RB0/INT Pin, External...................................... 4, 18, 29 RB3:RB0 Block Diagram ............................................ 17 RB7:RB4 Block Diagram ............................................ 17 RB7:RB4 Interrupt-on-Change ........................ 4, 17, 29 RB7:RB4 Interrupt-on-Change Enable (RBIE Bit) ...... 10 RB7:RB4 Interrupt-on-Change Flag (RBIF Bit).....10, 17 TRISB Register......................................... 7, 17, 18, 25 Postscaler, WDT Assignment (PSA Bit) ................................................... 9 Rate Select (PS2:PS0 Bits) .......................................... 9 Postscaler. See Prescaler Power-down (PD) Bit. See Power-on Reset (POR) Power-down Mode. See SLEEP Power-on Reset (POR).......................................... 21, 24, 26 Oscillator Start-up Timer (OST) ............................21, 26 PD Bit .................................................8, 24, 28, 32, 33 Power-up Timer (PWRT) ......................................21, 26 Time-out Sequence .................................................... 28 Time-out Sequence on Power-up .........................27, 28 TO Bit .......................................... 8, 24, 28, 30, 32, 33 Prescaler............................................................................. 19 Assignment (PSA Bit) ................................................. 19 Block Diagram ............................................................ 20 Rate Select (PS2:PS0 Bits) ........................................ 19 Switching Prescaler Assignment ................................ 20 2001-2013 Microchip Technology Inc. PIC16F84A Prescaler, Timer0 Assignment (PSA Bit) ................................................... 9 Rate Select (PS2:PS0 Bits) .......................................... 9 Program Counter ................................................................ 11 PCL Register....................................................7, 11, 25 PCLATH Register ............................................7, 11, 25 Reset Conditions......................................................... 24 Program Memory .................................................................. 5 General Purpose Registers........................................... 6 Interrupt Vector ...................................................... 5, 29 RESET Vector............................................................... 5 Special Function Registers ...................................... 6, 7 Programming, Device Instructions ...................................... 35 R RAM. See Data Memory Reader Response ............................................................... 86 Register File .......................................................................... 6 Register File Map .................................................................. 6 Registers Configuration Word ..................................................... 21 EECON1 (EEPROM Control)...................................... 13 INTCON ...................................................................... 10 OPTION ........................................................................ 9 STATUS........................................................................ 8 Reset............................................................................ 21, 24 Block Diagram...................................................... 24, 26 MCLR Reset. See MCLR Power-on Reset (POR). See Power-on Reset (POR) Reset Conditions for All Registers .............................. 25 Reset Conditions for Program Counter....................... 24 Reset Conditions for STATUS Register...................... 24 WDT Reset. See Watchdog Timer (WDT) Revision History .................................................................. 77 RP1:RP0 (Bank Select) bits .................................................. 8 Timing Conditions ............................................................... 54 Timing Diagrams CLKOUT and I/O ........................................................ 56 Diagrams and Specifications ...................................... 55 CLKOUT and I/O Requirements......................... 56 External Clock Requirements ............................. 55 RESET, Watchdog Timer, Oscillator Start-up Timer and Power-up Timer Requirements................................... 57 Timer0 Clock Requirements ............................... 58 External Clock ............................................................ 55 RESET, Watchdog Timer, Oscillator Start-up Timer and Power-up Timer................................. 57 Time-out Sequence on Power-up.........................27, 28 Timer0 Clock .............................................................. 58 Wake-up From Sleep Through Interrupt ..................... 32 Timing Parameter Symbology ............................................ 53 TO bit .................................................................................... 8 W W Register ....................................................................25, 30 Wake-up from SLEEP...............................21, 26, 28, 29, 32 Interrupts ..............................................................32, 33 MCLR Reset ............................................................... 32 WDT Reset ................................................................. 32 Watchdog Timer (WDT)................................................21, 30 Block Diagram ............................................................ 31 Postscaler. See Prescaler Programming Considerations ..................................... 31 RC Oscillator .............................................................. 30 Time-out Period .......................................................... 30 WDT Reset, Normal Operation................................... 24 WDT Reset, SLEEP .............................................24, 32 WWW Address ................................................................... 85 WWW, On-Line Support ....................................................... 2 S Z Saving W Register and STATUS in RAM ........................... 30 SLEEP ............................................................ 21, 24, 29, 32 Software Simulator (MPLAB SIM)....................................... 45 Special Features of the CPU .............................................. 21 Special Function Registers .............................................. 6, 7 Speed, Operating .............................................. 1, 22, 23, 55 Stack ................................................................................... 11 STATUS Register ............................................... 7, 8, 25, 30 C Bit .............................................................................. 8 DC Bit............................................................................ 8 PD Bit................................................. 8, 24, 28, 32, 33 Reset Conditions......................................................... 24 RP0 Bit.......................................................................... 6 TO Bit...........................................8, 24, 28, 30, 32, 33 Z Bit............................................................................... 8 Z (Zero) bit ............................................................................ 8 T Time-out (TO) Bit. See Power-on Reset (POR) Timer0 ................................................................................. 19 Associated Registers .................................................. 20 Block Diagram............................................................. 19 Clock Source Edge Select (T0SE Bit)........................... 9 Clock Source Select (T0CS Bit).................................... 9 Overflow Enable (T0IE Bit) .................................. 10, 29 Overflow Flag (T0IF Bit).................................10, 20, 29 Overflow Interrupt ................................................ 20, 29 Prescaler. See Prescaler RA4/T0CKI Pin, External Clock .................................. 19 TMR0 Register.................................................7, 20, 25 2001-2013 Microchip Technology Inc. DS35007C-page 83 PIC16F84A NOTES: DS35007C-page 84 2001-2013 Microchip Technology Inc. THE MICROCHIP WEB SITE CUSTOMER SUPPORT Microchip provides online support via our WWW site at www.microchip.com. This web site is used as a means to make files and information easily available to customers. Accessible by using your favorite Internet browser, the web site contains the following information: Users of Microchip products can receive assistance through several channels: * Product Support - Data sheets and errata, application notes and sample programs, design resources, user's guides and hardware support documents, latest software releases and archived software * General Technical Support - Frequently Asked Questions (FAQ), technical support requests, online discussion groups, Microchip consultant program member listing * Business of Microchip - Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives * * * * Distributor or Representative Local Sales Office Field Application Engineer (FAE) Technical Support Customers should contact their distributor, representative or field application engineer (FAE) for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in the back of this document. Technical support is available through the web site at: http://microchip.com/support CUSTOMER CHANGE NOTIFICATION SERVICE Microchip's customer notification service helps keep customers current on Microchip products. Subscribers will receive e-mail notification whenever there are changes, updates, revisions or errata related to a specified product family or development tool of interest. To register, access the Microchip web site at www.microchip.com. Under "Support", click on "Customer Change Notification" and follow the registration instructions. 2001-2013 Microchip Technology Inc. DS35007C-page 85 READER RESPONSE It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation can better serve you, please FAX your comments to the Technical Publications Manager at (480) 792-4150. Please list the following information, and use this outline to provide us with your comments about this document. TO: Technical Publications Manager RE: Reader Response Total Pages Sent ________ From: Name Company Address City / State / ZIP / Country Telephone: (_______) _________ - _________ FAX: (______) _________ - _________ Application (optional): Would you like a reply? Y N Device: Literature Number: DS35007C Questions: 1. What are the best features of this document? 2. How does this document meet your hardware and software development needs? 3. Do you find the organization of this document easy to follow? If not, why? 4. What additions to the document do you think would enhance the structure and subject? 5. What deletions from the document could be made without affecting the overall usefulness? 6. Is there any incorrect or misleading information (what and where)? 7. How would you improve this document? DS35007C-page 86 2001-2013 Microchip Technology Inc. PIC16F84A PIC16F84A PRODUCT IDENTIFICATION SYSTEM To order or obtain information (e.g., on pricing or delivery) refer to the factory or the listed sales office. PART NO. Device X -XX Frequency Temperature Range Range /XX XXX Package Pattern Device PIC16F84A(1), PIC16F84AT(2) PIC16LF84A(1), PIC16LF84AT(2) Frequency Range 04 20 = = Temperature Range I = 0C = -40C Package P = SO = SS = Pattern QTP, SQTP, ROM Code (factory specified) or Special Requirements . Blank for OTP and Windowed devices. 4 MHz 20 MHz Examples: a) PIC16F84A -04/P 301 = Commercial temp., PDIP package, 4 MHz, normal VDD limits, QTP pattern #301. b) PIC16LF84A - 04I/SO = Industrial temp., SOIC package, 200 kHz, Extended VDD limits. c) PIC16F84A - 20I/P = Industrial temp., PDIP package, 20 MHz, normal VDD limits. to +70C to +85C PDIP SOIC (Gull Wing, 300 mil body) SSOP 2001-2013 Microchip Technology Inc. Note 1: F = Standard VDD range LF = Extended VDD range 2: T = in tape and reel - SOIC and SSOP packages only. DS35007C-page87 PIC16F84A NOTES: DS35007C-page 88 2001-2013 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: * Microchip products meet the specification contained in their particular Microchip Data Sheet. * Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. * There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip's Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. * Microchip is willing to work with the customer who is concerned about the integrity of their code. * Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as "unbreakable." Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip's code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer's risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, FlashFlex, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, PIC32 logo, rfPIC, SST, SST Logo, SuperFlash and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MTP, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries. Analog-for-the-Digital Age, Application Maestro, BodyCom, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE, rfLAB, Select Mode, SQI, Serial Quad I/O, Total Endurance, TSHARC, UniWinDriver, WiperLock, ZENA and Z-Scale are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. GestIC and ULPP are registered trademarks of Microchip Technology Germany II GmbH & Co. & KG, a subsidiary of Microchip Technology Inc., in other countries. All other trademarks mentioned herein are property of their respective companies. (c) 2001-2013, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. ISBN: 9781620769409 QUALITY MANAGEMENT SYSTEM CERTIFIED BY DNV == ISO/TS 16949 == 2001-2013 Microchip Technology Inc. Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company's quality system processes and procedures are for its PIC(R) MCUs and dsPIC(R) DSCs, KEELOQ(R) code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001:2000 certified. DS35007C-page 89 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4123 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Japan - Osaka Tel: 81-6-6152-7160 Fax: 81-6-6152-9310 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8569-7000 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 China - Chongqing Tel: 86-23-8980-9588 Fax: 86-23-8980-9500 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 China - Hangzhou Tel: 86-571-2819-3187 Fax: 86-571-2819-3189 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Hong Kong SAR Tel: 852-2943-5100 Fax: 852-2401-3431 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Taiwan - Hsin Chu Tel: 886-3-5778-366 Fax: 886-3-5770-955 China - Shenzhen Tel: 86-755-8864-2200 Fax: 86-755-8203-1760 Taiwan - Kaohsiung Tel: 886-7-213-7828 Fax: 886-7-330-9305 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Taiwan - Taipei Tel: 886-2-2508-8600 Fax: 886-2-2508-0102 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 DS35007C-page 90 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Japan - Tokyo Tel: 81-3-6880- 3770 Fax: 81-3-6880-3771 11/29/12 2001-2013 Microchip Technology Inc.