P89LPC933/934/935/936 8-bit microcontroller with accelerated two-clock 80C51 core 4 kB/8 kB/16 kB 3 V byte-erasable flash with 8-bit ADCs Rev. 8 -- 12 January 2011 Product data sheet 1. General description The P89LPC933/934/935/936 is a single-chip microcontroller, available in low cost packages, based on a high performance processor architecture that executes instructions in two to four clocks, six times the rate of standard 80C51 devices. Many system-level functions have been incorporated into the P89LPC933/934/935/936 in order to reduce component count, board space, and system cost. 2. Features and benefits 2.1 Principal features 4 kB/8 kB/16 kB byte-erasable flash code memory organized into 1 kB/2 kB sectors and 64-byte pages. Single-byte erasing allows any byte(s) to be used as non-volatile data storage. 256-byte RAM data memory. Both the P89LPC935 and P89LPC936 also include a 512-byte auxiliary on-chip RAM. 512-byte customer data EEPROM on chip allows serialization of devices, storage of setup parameters, etc. (P89LPC935/936). Dual 4-input multiplexed 8-bit A/D converters/DAC outputs (P89LPC935/936, single A/D on P89LPC933/934).Two analog comparators with selectable inputs and reference source. Two 16-bit counter/timers (each may be configured to toggle a port output upon timer overflow or to become a PWM output) and a 23-bit system timer that can also be used as an RTC. Enhanced UART with fractional baud rate generator, break detect, framing error detection, and automatic address detection; 400 kHz byte-wide I2C-bus communication port and SPI communication port. Capture/Compare Unit (CCU) provides PWM, input capture, and output compare functions (P89LPC935/936). High-accuracy internal RC oscillator option allows operation without external oscillator components. The RC oscillator option is selectable and fine tunable. 2.4 V to 3.6 V VDD operating range. I/O pins are 5 V tolerant (may be pulled up or driven to 5.5 V). 28-pin TSSOP, PLCC, and HVQFN packages with 23 I/O pins minimum and up to 26 I/O pins while using on-chip oscillator and reset options. P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 2.2 Additional features A high performance 80C51 CPU provides instruction cycle times of 111 ns to 222 ns for all instructions except multiply and divide when executing at 18 MHz. This is six times the performance of the standard 80C51 running at the same clock frequency. A lower clock frequency for the same performance results in power savings and reduced EMI. Serial flash In-Circuit Programming (ICP) allows simple production coding with commercial EPROM programmers. Flash security bits prevent reading of sensitive application programs. Serial flash In-System Programming (ISP) allows coding while the device is mounted in the end application. In-Application Programming (IAP) of the flash code memory. This allows changing the code in a running application. Watchdog timer with separate on-chip oscillator, requiring no external components. The watchdog prescaler is selectable from eight values. Low voltage reset (brownout detect) allows a graceful system shutdown when power fails. May optionally be configured as an interrupt. Idle and two different power-down reduced power modes. Improved wake-up from Power-down mode (a LOW interrupt input starts execution). Typical power-down current is 1 A (total power-down with voltage comparators disabled). Active-LOW reset. On-chip power-on reset allows operation without external reset components. A reset counter and reset glitch suppression circuitry prevent spurious and incomplete resets. A software reset function is also available. Configurable on-chip oscillator with frequency range options selected by user programmed flash configuration bits. Oscillator options support frequencies from 20 kHz to the maximum operating frequency of 18 MHz. Oscillator fail detect. The watchdog timer has a separate fully on-chip oscillator allowing it to perform an oscillator fail detect function. Programmable port output configuration options: quasi-bidirectional, open drain, push-pull, input-only. Port `input pattern match' detect. Port 0 may generate an interrupt when the value of the pins match or do not match a programmable pattern. LED drive capability (20 mA) on all port pins. A maximum limit is specified for the entire chip. Controlled slew rate port outputs to reduce EMI. Outputs have approximately 10 ns minimum ramp times. Only power and ground connections are required to operate the P89LPC933/934/935/936 when internal reset option is selected. Four interrupt priority levels. Eight keypad interrupt inputs, plus two additional external interrupt inputs. Schmitt trigger port inputs. Second data pointer. Emulation support. P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 2 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 3. Product comparison overview Table 1 highlights the differences between the four devices. For a complete list of device features please see Section 2 "Features and benefits". Table 1. Product comparison overview Device Flash memory Sector size ADC1 ADC0 CCU Data EEPROM P89LPC933 4 kB 1 kB X - - - P89LPC934 8 kB 1 kB X - - - P89LPC935 8 kB 1 kB X X X X P89LPC936 16 kB 2 kB X X X X 4. Ordering information Table 2. Ordering information Type number Package Name Description Version P89LPC935FA PLCC28 plastic leaded chip carrier; 28 leads SOT261-2 P89LPC933HDH TSSOP28 plastic thin shrink small outline package; 28 leads; body width 4.4 mm SOT361-1 HVQFN28 plastic thermal enhanced very thin quad flat package; no leads; 28 terminals; body 6 x 6 x 0.85 mm SOT788-1 P89LPC933FDH P89LPC934FDH P89LPC935FDH P89LPC936FDH P89LPC935FHN 4.1 Ordering options Table 3. Ordering options Type number Flash memory Temperature range Frequency P89LPC933HDH 4 kB -40 C to +125 C 0 MHz to 18 MHz P89LPC933FDH 4 kB -40 C to +85 C P89LPC935FA 8 kB P89LPC934FDH P89LPC935FDH P89LPC935FHN P89LPC936FDH P89LPC933_934_935_936 Product data sheet 16 kB All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 3 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 5. Block diagram P89LPC933/934/935/936 ACCELERATED 2-CLOCK 80C51 CPU 4 kb/8 kB/16 kB CODE FLASH TXD RXD I2C-BUS SCL SDA internal bus 256-BYTE DATA RAM 512-BYTE AUXILIARY RAM SPICLK MOSI MISO SS SPI REAL-TIME CLOCK/ SYSTEM TIMER 512-BYTE DATA EEPROM (P89LPC935/936) P3[1:0] PORT 3 CONFIGURABLE I/Os P2[7:0] PORT 2 CONFIGURABLE I/Os P1[7:0] PORT 1 CONFIGURABLE I/Os T0 T1 TIMER 0 TIMER 1 PORT 0 CONFIGURABLE I/Os P0[7:0] UART ANALOG COMPARATORS CMP2 CIN2B CIN2A CMP1 CIN1A CIN1B CCU (CAPTURE/ COMPARE UNIT) (P89LPC935/936) OCA OCB OCC OCD ICA ICB ADC1/DAC1 AD10 AD11 AD12 AD13 DAC1 ADC0/DAC0 (P89LPC935/936) AD00 AD01 AD02 AD03 DAC1 KEYPAD INTERRUPT WATCHDOG TIMER AND OSCILLATOR PROGRAMMABLE OSCILLATOR DIVIDER CRYSTAL OR RESONATOR X1 X2 CONFIGURABLE OSCILLATOR CPU clock ON-CHIP RC OSCILLATOR POWER MONITOR (POWER-ON RESET, BROWNOUT RESET) 002aab070 Fig 1. Block diagram P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 4 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 6. Pinning information 6.1 Pinning P2.0/DAC0 1 28 P2.7 P2.1 2 27 P2.6 P0.0/CMP2/KBI0 3 26 P0.1/CIN2B/KBI1/AD10 P1.7 4 25 P0.2/CIN2A/KBI2/AD11 P1.6 5 24 P0.3/CIN1B/KBI3/AD12 P1.5/RST 6 VSS 7 P3.1/XTAL1 8 P3.0/XTAL2/CLKOUT 9 23 P0.4/CIN1A/KBI4/DAC1/AD13 P89LPC933HDH P89LPC933FDH P89LPC934FDH 22 P0.5/CMPREF/KBI5 21 VDD 20 P0.6/CMP1/KBI6 P1.4/INT1 10 19 P0.7/T1/KBI7 P1.3/INT0/SDA 11 18 P1.0/TXD P1.2/T0/SCL 12 17 P1.1/RXD P2.2/MOSI 13 16 P2.5/SPICLK P2.3/MISO 14 15 P2.4/SS 002aab071 Fig 2. P89LPC933/934 TSSOP28 pin configuration P2.0/ICB/DAC0/AD03 1 28 P2.7/ICA P2.1/OCD/AD02 2 27 P2.6/OCA P0.0/CMP2/KBI0/AD01 3 26 P0.1/CIN2B/KBI1/AD10 P1.7/OCC/AD00 4 25 P0.2/CIN2A/KBI2/AD11 P1.6/OCB 5 24 P0.3/CIN1B/KBI3/AD12 P1.5/RST 6 23 P0.4/CIN1A/KBI4/DAC1/AD13 VSS 7 P3.1/XTAL1 8 P3.0/XTAL2/CLKOUT 9 P89LPC935FDH P89LPC936FDH 22 P0.5/CMPREF/KBI5 21 VDD 20 P0.6/CMP1/KBI6 P1.4/INT1 10 19 P0.7/T1/KBI7 P1.3/INT0/SDA 11 18 P1.0/TXD P1.2/T0/SCL 12 17 P1.1/RXD P2.2/MOSI 13 16 P2.5/SPICLK P2.3/MISO 14 15 P2.4/SS 002aab072 Fig 3. P89LPC933_934_935_936 Product data sheet P89LPC935/936 TSSOP28 pin configuration All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 5 of 77 P89LPC933/934/935/936 NXP Semiconductors P2.0/ICB/DAC0/AD03 1 26 P0.1/CIN2B/KBI1/AD10 P2.1/OCD/AD02 2 27 P2.6/OCA P0.0/CMP2/KBI0/AD01 3 28 P2.7/ICA P1.7/OCC/AD00 4 8-bit microcontroller with accelerated two-clock 80C51 core P1.6/OCB 5 25 P0.2/CIN2A/KBI2/AD11 P1.5/RST 6 24 P0.3/CIN1B/KBI3/AD12 VSS 7 23 P0.4/CIN1A/KBI4/DAC1/AD13 P3.1/XTAL1 8 P3.0/XTAL2/CLKOUT 9 22 P0.5/CMPREF/KBI5 P89LPC935FA 21 VDD 20 P0.6/CMP1/KBI6 P1.4/INT1 10 19 P0.7/T1/KBI7 P1.1/RXD 17 P1.0/TXD 18 23 P2.6/OCA 22 P0.1/CIN2B/KBI1/AD10 P2.5/SPICLK 16 P2.4/SS 15 P2.3/MISO 14 002aab074 24 P2.7/ICA 25 P2.0/ICB/DAC0/AD03 26 P2.1/OCD/AD02 terminal 1 index area 27 P0.0/CMP2/KBI0/AD01 28 P1.7/OCC/AD00 P89LPC935 PLCC28 pin configuration P1.6/OCB 1 21 P0.2/CIN2A/KBI2/AD11 P1.5/RST VSS 2 20 P0.3/CIN1B/KBI3/AD12 P3.1/XTAL1 4 P3.0/XTAL2/CLKOUT 5 17 VDD P1.4/INT1 6 16 P0.6/CMP1/KBI6 P1.3/INT0/SDA 7 15 P0.7/T1/KBI7 19 P0.4/CIN1A/KBI4/DAC1/AD13 3 18 P1.0/TXD 14 P1.1/RXD 13 P2.5/SPICLK 12 P2.4/SS 11 9 P2.3/MISO 10 8 P2.2/MOSI P89LPC935FHN P1.2/T0/SCL Fig 4. P2.2/MOSI 13 P1.2/T0/SCL 12 P1.3/INT0/SDA 11 P0.5/CMPREF/KBI5 002aab076 Transparent top view Fig 5. P89LPC933_934_935_936 Product data sheet P89LPC935 HVQFN28 pin configuration All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 6 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 6.2 Pin description Table 4. Pin description Symbol Pin Type Description I/O Port 0: Port 0 is an 8-bit I/O port with a user-configurable output type. During reset Port 0 latches are configured in the input only mode with the internal pull-up disabled. The operation of Port 0 pins as inputs and outputs depends upon the port configuration selected. Each port pin is configured independently. Refer to Section 8.13.1 "Port configurations" and Table 11 "Static characteristics" for details. TSSOP28, HVQFN28 PLCC28 P0.0 to P0.7 The Keypad Interrupt feature operates with Port 0 pins. All pins have Schmitt trigger inputs. Port 0 also provides various special functions as described below: P0.0/CMP2/ KBI0/AD01 P0.1/CIN2B/ KBI1/AD10 P0.2/CIN2A/ KBI2/AD11 P0.3/CIN1B/ KBI3/AD12 P0.4/CIN1A/ KBI4/DAC1/ AD13 3 26 25 24 23 P0.5/ CMPREF/ KBI5 22 P0.6/CMP1/ KBI6 20 P0.7/T1/ KBI7 19 P89LPC933_934_935_936 Product data sheet 27 22 21 20 19 18 16 15 I/O P0.0 -- Port 0 bit 0. O CMP2 -- Comparator 2 output. I KBI0 -- Keyboard input 0. I AD01 -- ADC0 channel 1 analog input. (P89LPC935/936) I/O P0.1 -- Port 0 bit 1. I CIN2B -- Comparator 2 positive input B. I KBI1 -- Keyboard input 1. I AD10 -- ADC1 channel 0 analog input. I/O P0.2 -- Port 0 bit 2. I CIN2A -- Comparator 2 positive input A. I KBI2 -- Keyboard input 2. I AD11 -- ADC1 channel 1 analog input. I/O P0.3 -- Port 0 bit 3. I CIN1B -- Comparator 1 positive input B. I KBI3 -- Keyboard input 3. I AD12 -- ADC1 channel 2 analog input. I/O P0.4 -- Port 0 bit 4. I CIN1A -- Comparator 1 positive input A. I KBI4 -- Keyboard input 4. O DAC1 -- Digital-to-analog converter output 1. I AD13 -- ADC1 channel 3 analog input. I/O P0.5 -- Port 0 bit 5. I CMPREF -- Comparator reference (negative) input. I KBI5 -- Keyboard input 5. I/O P0.6 -- Port 0 bit 6. O CMP1 -- Comparator 1 output. I KBI6 -- Keyboard input 6. I/O P0.7 -- Port 0 bit 7. I/O T1 -- Timer/counter 1 external count input or overflow output. I KBI7 -- Keyboard input 7. All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 7 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core Table 4. Pin description ...continued Symbol Pin Type Description TSSOP28, HVQFN28 PLCC28 I/O, I [1] Port 1: Port 1 is an 8-bit I/O port with a user-configurable output type, except for three pins as noted below. During reset Port 1 latches are configured in the input only mode with the internal pull-up disabled. The operation of the configurable Port 1 pins as inputs and outputs depends upon the port configuration selected. Each of the configurable port pins are programmed independently. Refer to Section 8.13.1 "Port configurations" and Table 11 "Static characteristics" for details. P1.2 and P1.3 are open drain when used as outputs. P1.5 is input only. P1.0 to P1.7 All pins have Schmitt trigger inputs. Port 1 also provides various special functions as described below: P1.0/TXD 18 14 P1.1/RXD 17 13 P1.2/T0/SCL 12 P1.3/INT0/ SDA P1.4/INT1 P1.5/RST P1.6/OCB P1.7/OCC/ AD00 11 10 6 5 4 P89LPC933_934_935_936 Product data sheet 8 7 6 2 1 28 I/O P1.0 -- Port 1 bit 0. O TXD -- Transmitter output for the serial port. I/O P1.1 -- Port 1 bit 1. I RXD -- Receiver input for the serial port. I/O P1.2 -- Port 1 bit 2 (open-drain when used as output). I/O T0 -- Timer/counter 0 external count input or overflow output (open-drain when used as output). I/O SCL -- I2C serial clock input/output. I/O P1.3 -- Port 1 bit 3 (open-drain when used as output). I INT0 -- External interrupt 0 input. I/O SDA -- I2C serial data input/output. I P1.4 -- Port 1 bit 4. I INT1 -- External interrupt 1 input. I P1.5 -- Port 1 bit 5 (input only). I RST -- External reset input during power-on or if selected via UCFG1. When functioning as a reset input, a LOW on this pin resets the microcontroller, causing I/O ports and peripherals to take on their default states, and the processor begins execution at address 0. Also used during a power-on sequence to force ISP mode. When using an oscillator frequency above 12 MHz, the reset input function of P1.5 must be enabled. An external circuit is required to hold the device in reset at power-up until VDD has reached its specified level. When system power is removed VDD will fall below the minimum specified operating voltage. When using an oscillator frequency above 12 MHz, in some applications, an external brownout detect circuit may be required to hold the device in reset when VDD falls below the minimum specified operating voltage. I/O P1.6 -- Port 1 bit 6. O OCB -- Output Compare B. (P89LPC935/936) I/O P1.7 -- Port 1 bit 7. O OCC -- Output Compare C. (P89LPC935/936) I AD00 -- ADC0 channel 0 analog input. (P89LPC935/936) All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 8 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core Table 4. Pin description ...continued Symbol Pin Type Description I/O Port 2: Port 2 is an 8-bit I/O port with a user-configurable output type. During reset Port 2 latches are configured in the input only mode with the internal pull-up disabled. The operation of Port 2 pins as inputs and outputs depends upon the port configuration selected. Each port pin is configured independently. Refer to Section 8.13.1 "Port configurations" and Table 11 "Static characteristics" for details. TSSOP28, HVQFN28 PLCC28 P2.0 to P2.7 All pins have Schmitt trigger inputs. Port 2 also provides various special functions as described below: P2.0/ICB/ DAC0/AD03 P2.1/OCD/ AD02 P2.2/MOSI P2.3/MISO P2.4/SS 1 2 13 14 15 P2.5/ SPICLK 16 P2.6/OCA 27 P2.7/ICA 28 P89LPC933_934_935_936 Product data sheet 25 26 9 10 11 12 I/O P2.0 -- Port 2 bit 0. I ICB -- Input Capture B. (P89LPC935/936) I DAC0 -- Digital-to-analog converter output. I AD03 -- ADC0 channel 3 analog input. (P89LPC935/936) I/O P2.1 -- Port 2 bit 1. O OCD -- Output Compare D. (P89LPC935/936) I AD02 -- ADC0 channel 2 analog input. (P89LPC935/936) I/O P2.2 -- Port 2 bit 2. I/O MOSI -- SPI master out slave in. When configured as master, this pin is output; when configured as slave, this pin is input. I/O P2.3 -- Port 2 bit 3. I/O MISO -- When configured as master, this pin is input, when configured as slave, this pin is output. I/O P2.4 -- Port 2 bit 4. I SS -- SPI Slave select. I/O P2.5 -- Port 2 bit 5. I/O SPICLK -- SPI clock. When configured as master, this pin is output; when configured as slave, this pin is input. 23 I/O P2.6 -- Port 2 bit 6. O OCA -- Output Compare A. (P89LPC935/936) 24 I/O P2.7 -- Port 2 bit 7. I ICA -- Input Capture A. (P89LPC935/936) All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 9 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core Table 4. Pin description ...continued Symbol Pin Type Description I/O Port 3: Port 3 is a 2-bit I/O port with a user-configurable output type. During reset Port 3 latches are configured in the input only mode with the internal pull-up disabled. The operation of Port 3 pins as inputs and outputs depends upon the port configuration selected. Each port pin is configured independently. Refer to Section 8.13.1 "Port configurations" and Table 11 "Static characteristics" for details. TSSOP28, HVQFN28 PLCC28 P3.0 to P3.1 All pins have Schmitt trigger inputs. Port 3 also provides various special functions as described below: P3.0/XTAL2/ 9 CLKOUT P3.1/XTAL1 8 5 4 I/O P3.0 -- Port 3 bit 0. O XTAL2 -- Output from the oscillator amplifier (when a crystal oscillator option is selected via the flash configuration. O CLKOUT -- CPU clock divided by 2 when enabled via SFR bit (ENCLK TRIM.6). It can be used if the CPU clock is the internal RC oscillator, watchdog oscillator or external clock input, except when XTAL1/XTAL2 are used to generate clock source for the RTC/system timer. I/O P3.1 -- Port 3 bit 1. I XTAL1 -- Input to the oscillator circuit and internal clock generator circuits (when selected via the flash configuration). It can be a port pin if internal RC oscillator or watchdog oscillator is used as the CPU clock source, and if XTAL1/XTAL2 are not used to generate the clock for the RTC/system timer. VSS 7 3 I Ground: 0 V reference. VDD 21 17 I Power supply: This is the power supply voltage for normal operation as well as Idle and Power-down modes. [1] Input/output for P1.0 to P1.4, P1.6, P1.7. Input for P1.5. P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 10 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 7. Logic symbols VDD DAC1 KBI0 KBI1 KBI2 KBI3 KBI4 KBI5 KBI6 KBI7 CMP2 CIN2B CIN2A CIN1B CIN1A CMPREF CMP1 T1 CLKOUT XTAL2 AD10 AD11 AD12 AD13 VSS PORT 0 PORT 1 TXD RXD T0 INT0 INT1 RST SCL SDA P89LPC933 P89LPC934 PORT 3 XTAL1 PORT 2 DAC0 MOSI MISO SS SPICLK 002aab077 Fig 6. P89LPC933/934 logic symbol VDD DAC1 AD01 AD10 AD11 AD12 AD13 KBI0 KBI1 KBI2 KBI3 KBI4 KBI5 KBI6 KBI7 CMP2 CIN2B CIN2A CIN1B CIN1A CMPREF CMP1 T1 CLKOUT XTAL2 VSS PORT 0 PORT 1 P89LPC935 P89LPC936 PORT 3 XTAL1 PORT 2 TXD RXD T0 INT0 INT1 RST OCB OCC ICB OCD MOSI MISO SS SPICLK OCA ICA SCL SDA AD00 AD03 AD02 DAC0 002aab078 Fig 7. P89LPC935/936 logic symbol P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 11 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 8. Functional description Remark: Please refer to the P89LPC933/934/935/936 User manual for a more detailed functional description. 8.1 Special function registers Remark: SFR accesses are restricted in the following ways: * User must not attempt to access any SFR locations not defined. * Accesses to any defined SFR locations must be strictly for the functions for the SFRs. * SFR bits labeled `-', logic 0 or logic 1 can only be written and read as follows: - `-' Unless otherwise specified, must be written with logic 0, but can return any value when read (even if it was written with logic 0). It is a reserved bit and may be used in future derivatives. - Logic 0 must be written with logic 0, and will return a logic 0 when read. - Logic 1 must be written with logic 1, and will return a logic 1 when read. P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 12 of 77 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx NXP Semiconductors P89LPC933_934_935_936 Product data sheet Table 5. Special function registers - P89LPC933/934 * indicates SFRs that are bit addressable. Name Description SFR Bit functions and addresses addr. MSB Bit address E7 E6 E5 Reset value LSB E4 E3 E2 E1 Accumulator E0H ADCON0 A/D control register 0 8EH - - - - - ENADC0 - ADCON1 A/D control register 1 97H ENBI1 ENADCI 1 TMM1 EDGE1 ADCI1 ENADC1 ADCS11 ADINS A/D input select A3H ADI13 ADI12 ADI11 ADI10 - - - ADMODA A/D mode register A C0H BNDI1 BURST1 SCC1 SCAN1 - - ADMODB A/D mode register B A1H CLK2 CLK1 CLK0 - AD0DAT3 A/D_0 data register 3 AD1BH Binary 00 0000 0000 E0 00 0000 0000 ADCS10 00 - 0000 0000 - 00 0000 0000 - 00 0000 0000 - 00 000x 0000 F4H 00 0000 0000 A/D_1 boundary high register C4H FF 1111 1111 AD1BL A/D_1 boundary low register BCH 00 0000 0000 AD1DAT0 A/D_1 data register 0 D5H 00 0000 0000 AD1DAT1 A/D_1 data register 1 D6H 00 0000 0000 AD1DAT2 A/D_1 data register 2 D7H 00 0000 0000 AD1DAT3 A/D_1 data register 3 F5H AUXR1 Auxiliary function register A2H 00 0000 0000 00[1] 0000 00x0 F0H 00 0000 0000 0000 0000 Bit address B* B register CLKLP EBRR ENT1 ENT0 SRST 0 - DPS F7 F6 F5 F4 F3 F2 F1 F0 BRGR0 Baud rate generator rate low BEH 00[2] BRGR1 Baud rate generator rate high BFH 00[1][2] 0000 0000 BRGCON Baud rate generator control BDH BRGEN 00[2] xxxx xx00 CMF1 00[1] xx00 0000 CMF2 00[1] xx00 0000 CMP1 Comparator 1 control register ACH - - CE1 CE2 CP1 CP2 CN1 CN2 OE1 OE2 SBRGS CO1 13 of 77 (c) NXP B.V. 2011. All rights reserved. CMP2 Comparator 2 control register ADH DIVM CPU clock divide-by-M control 95H CO2 00 0000 0000 DPTR Data pointer (2 bytes) DPH Data pointer high 83H 00 0000 0000 DPL Data pointer low 82H 00 0000 0000 Program flash address high E7H 00 0000 0000 FMADRH P89LPC933/934/935/936 BSA1 ENDAC1 ENDAC0 8-bit microcontroller with accelerated two-clock 80C51 core Rev. 8 -- 12 January 2011 All information provided in this document is subject to legal disclaimers. ACC* Hex xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Name Description SFR Bit functions and addresses addr. MSB FMADRL Program flash address low E6H FMCON Program flash control (Read) E4H Program flash control (Write) E4H FMDATA Program flash data E5H I2ADR I2C slave address register DBH I2CON* I2 C control register I2DAT I2C data register I2SCLH Serial clock generator/SCL duty cycle register high I2SCLL BUSY - - Reset value LSB - HVA HVE SV OI Hex Binary 00 0000 0000 70 0111 0000 FMCMD. FMCMD. FMCMD. FMCMD. FMCMD. FMCMD. FMCMD. FMCMD. 7 6 5 4 3 2 1 0 00 0000 0000 00 0000 0000 00 x000 00x0 DDH 00 0000 0000 Serial clock generator/SCL duty cycle register low DCH 00 0000 0000 I2STAT I2C status register D9H F8 1111 1000 ICRAH Input capture A register high ABH 00 0000 0000 ICRAL Input capture A register low AAH 00 0000 0000 ICRBH Input capture B register high AFH 00 0000 0000 ICRBL Input capture B register low AEH 00 0000 0000 00 0000 0000 00[3] 00x0 0000 Bit address D8H Interrupt enable 1 A8H Bit address E8H Bit address IP0* IP0H Interrupt priority 0 Interrupt priority 0 high B8H B7H 14 of 77 (c) NXP B.V. 2011. All rights reserved. Bit address IP1* IP1H Interrupt priority 1 Interrupt priority 1 high I2ADR.4 I2ADR.3 I2ADR.2 I2ADR.1 I2ADR.0 GC DF DE DD DC DB DA D9 D8 - I2EN STA STO SI AA - CRSEL F8H F7H STA.4 STA.3 STA.2 STA.1 STA.0 0 0 0 AF AE AD AC AB AA A9 A8 EA EWDRT EBO ES/ESR ET1 EX1 ET0 EX0 EF EE ED EC EB EA E9 E8 EAD EST - - ESPI EC EKBI EI2C BF BE BD BC BB BA B9 B8 - PWDRT PBO PS/PSR PT1 PX1 PT0 PX0 00[3] x000 0000 00[3] x000 0000 - PWDRT H PBOH PSH/ PSRH PT1H PX1H PT0H PX0H FF FE FD FC FB FA F9 F8 PAD PST - - PSPI PC PKBI PI2C 00[3] 00x0 0000 PI2CH 00[3] 00x0 0000 PADH PSTH - - PSPIH PCH PKBIH P89LPC933/934/935/936 IEN1* I2ADR.5 8-bit microcontroller with accelerated two-clock 80C51 core Rev. 8 -- 12 January 2011 All information provided in this document is subject to legal disclaimers. Interrupt enable 0 I2ADR.6 DAH Bit address IEN0* NXP Semiconductors P89LPC933_934_935_936 Product data sheet Table 5. Special function registers - P89LPC933/934 ...continued * indicates SFRs that are bit addressable. xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Name Description SFR Bit functions and addresses addr. MSB KBCON Keypad control register 94H KBMASK Keypad interrupt mask register 86H KBPATN Keypad pattern register P1* Port 1 80H Bit address 90H Bit address P2* - - - - PATN _SEL LSB Hex Binary KBIF 00[3] xxxx xx00 00 0000 0000 FF 1111 1111 Port 2 A0H Bit address 87 86 85 84 83 82 81 80 T1/KB7 CMP1 /KB6 CMPREF /KB5 CIN1A /KB4 CIN1B /KB3 CIN2A /KB2 CIN2B /KB1 CMP2 /KB0 97 96 95 94 93 92 91 90 - - RST INT1 INT0/ SDA T0/SCL RXD TXD A7 A6 A5 A4 A3 A2 A1 A0 - - SPICLK SS MISO MOSI - - B7 B6 B5 B4 B3 B2 B1 B0 - - - - - - XTAL1 XTAL2 [3] [3] [3] [3] Port 3 B0H P0M1 Port 0 output mode 1 84H (P0M1.7) (P0M1.6) (P0M1.5) (P0M1.4) (P0M1.3) (P0M1.2) (P0M1.1) (P0M1.0) FF[3] 00[3] P0M2 Port 0 output mode 2 85H (P0M2.7) (P0M2.6) (P0M2.5) (P0M2.4) (P0M2.3) (P0M2.2) (P0M2.1) (P0M2.0) P1M1 Port 1 output mode 1 91H (P1M1.7) (P1M1.6) P1M2 P2M1 Port 1 output mode 2 92H Port 2 output mode 1 A4H P2M2 Port 2 output mode 2 A5H P3M1 Port 3 output mode 1 B1H (P1M1.4) (P1M1.3) (P1M1.2) (P1M1.1) (P1M1.0) D3[3] 11x1 xx11 - (P1M2.4) (P1M2.3) (P1M2.2) (P1M2.1) (P1M2.0) 00[3] 00x0 xx00 (P2M1.7) (P2M1.6) (P2M1.5) (P2M1.4) (P2M1.3) (P2M1.2) (P2M1.1) (P2M1.0) FF[3] 1111 1111 (P2M2.7) (P2M2.6) (P2M2.5) (P2M2.4) (P2M2.3) (P2M2.2) (P2M2.1) (P2M2.0) 00[3] 0000 0000 (P1M2.7) (P1M2.6) - - - - - - (P3M1.1) (P3M1.0) 03[3] xxxx xx11 (P3M2.1) (P3M2.0) 00[3] xxxx xx00 PMOD1 00 0000 0000 00[3] 0000 0000 Port 3 output mode 2 B2H - - - - - - PCON Power control register 87H SMOD1 SMOD0 BOPD BOI GF1 GF0 Power control register A B5H 15 of 77 (c) NXP B.V. 2011. All rights reserved. Bit address 0000 0000 - P3M2 PCONA 1111 1111 PMOD0 RTCPD - VCPD ADPD I2PD SPPD SPD - D7 D6 D5 D4 D3 D2 D1 D0 F0 RS1 RS0 OV F1 P 00 0000 0000 - 00 xx00 000x PSW* Program status word D0H CY AC PT0AD Port 0 digital input disable F6H - - RSTSRC Reset source register DFH - - BOF POF R_BK R_WD R_SF R_EX RTCCON Real-time clock control D1H RTCF RTCS1 RTCS0 - - - ERTC RTCEN PT0AD.5 PT0AD.4 PT0AD.3 PT0AD.2 PT0AD.1 [4] 60[3][5] 011x xx00 P89LPC933/934/935/936 P3* 8-bit microcontroller with accelerated two-clock 80C51 core Rev. 8 -- 12 January 2011 All information provided in this document is subject to legal disclaimers. Port 0 - Reset value 93H Bit address P0* - NXP Semiconductors P89LPC933_934_935_936 Product data sheet Table 5. Special function registers - P89LPC933/934 ...continued * indicates SFRs that are bit addressable. xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Name Description SFR Bit functions and addresses addr. MSB Reset value LSB Hex Binary 0000 0000 RTCH Real-time clock register high D2H 00[5] RTCL Real-time clock register low D3H 00[5] 0000 0000 SADDR Serial port address register A9H 00 0000 0000 SADEN Serial port address enable B9H 00 0000 0000 SBUF Serial Port data buffer register 99H xx xxxx xxxx Bit address 9F 9E 9D 9C 9B 9A 99 98 98H SM0/FE SM1 SM2 REN TB8 RB8 TI RI 00 0000 0000 SSTAT Serial port extended status register BAH DBMOD INTLO CIDIS DBISEL FE BR OE STINT 00 0000 0000 SP Stack pointer 81H 07 0000 0111 SPCTL SPI control register E2H SSIG SPEN DORD MSTR CPOL CPHA SPR1 SPR0 04 0000 0100 SPSTAT SPI status register E1H SPIF WCOL - - - - - - 00 00xx xxxx SPDAT SPI data register E3H 00 0000 0000 TAMOD Timer 0 and 1 auxiliary mode 8FH - - - T1M2 - - - T0M2 00 xxx0 xxx0 8F 8E 8D 8C 8B 8A 89 88 TF1 TR1 TF0 TR0 IE1 IT1 IE0 IT0 00 0000 0000 TCON* Timer 0 and 1 control 88H TH0 Timer 0 high 8CH 00 0000 0000 TH1 Timer 1 high 8DH 00 0000 0000 TL0 Timer 0 low 8AH 00 0000 0000 TL1 Timer 1 low 8BH 00 0000 0000 TMOD Timer 0 and 1 mode 89H T1GATE T1C/T T1M1 T1M0 T0GATE T0C/T T0M1 T0M0 TRIM Internal oscillator trim register 96H RCCLK ENCLK TRIM.5 TRIM.4 TRIM.3 TRIM.2 TRIM.1 TRIM.0 00 [6] [5] 0000 0000 WDCON Watchdog control register A7H PRE2 PRE1 PRE0 - - WDRUN WDTOF WDCLK [7] [5] 16 of 77 (c) NXP B.V. 2011. All rights reserved. P89LPC933/934/935/936 Serial port control 8-bit microcontroller with accelerated two-clock 80C51 core Rev. 8 -- 12 January 2011 All information provided in this document is subject to legal disclaimers. SCON* Bit address NXP Semiconductors P89LPC933_934_935_936 Product data sheet Table 5. Special function registers - P89LPC933/934 ...continued * indicates SFRs that are bit addressable. xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Name Description SFR Bit functions and addresses addr. MSB WDL Watchdog load C1H WFEED1 Watchdog feed 1 C2H WFEED2 Watchdog feed 2 C3H NXP Semiconductors P89LPC933_934_935_936 Product data sheet Table 5. Special function registers - P89LPC933/934 ...continued * indicates SFRs that are bit addressable. Reset value LSB Hex Binary FF 1111 1111 Unimplemented bits in SFRs (labeled '-') are X (unknown) at all times. Unless otherwise specified, ones should not be written to these bits since they may be used for other purposes in future derivatives. The reset values shown for these bits are logic 0s although they are unknown when read. [2] BRGR1 and BRGR0 must only be written if BRGEN in BRGCON SFR is logic 0. If any are written while BRGEN = 1, the result is unpredictable. [3] All ports are in input only (high-impedance) state after power-up. [4] The RSTSRC register reflects the cause of the P89LPC933/934/935/936 reset. Upon a power-up reset, all reset source flags are cleared except POF and BOF; the power-on reset value is xx11 0000. [5] The only reset source that affects these SFRs is power-on reset. [6] On power-on reset, the TRIM SFR is initialized with a factory preprogrammed value. Other resets will not cause initialization of the TRIM register. [7] After reset, the value is 1110 01x1, i.e., PRE2 to PRE0 are all logic 1, WDRUN = 1 and WDCLK = 1. WDTOF bit is logic 1 after watchdog reset and is logic 0 after power-on reset. Other resets will not affect WDTOF. P89LPC933/934/935/936 17 of 77 (c) NXP B.V. 2011. All rights reserved. 8-bit microcontroller with accelerated two-clock 80C51 core Rev. 8 -- 12 January 2011 All information provided in this document is subject to legal disclaimers. [1] xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx NXP Semiconductors P89LPC933_934_935_936 Product data sheet Table 6. Special function registers - P89LPC935/936 * indicates SFRs that are bit addressable. Name Description SFR Bit functions and addresses addr. MSB Bit address E7 E6 E5 Reset value LSB E4 E3 E2 E1 Hex Binary 00 0000 0000 E0 ACC* Accumulator E0H ADCON0 A/D control register 0 8EH ENBI0 ENADCI 0 TMM0 EDGE0 ADCI0 ENADC0 ADCS01 ADCS00 00 0000 0000 ADCON1 A/D control register 1 97H ENBI1 ENADCI 1 TMM1 EDGE1 ADCI1 ENADC1 ADCS11 ADCS10 00 0000 0000 A/D input select A3H ADI13 ADI12 ADI11 ADI10 ADI03 ADI02 ADI01 ADI00 00 0000 0000 ADMODA A/D mode register A C0H BNDI1 BURST1 SCC1 SCAN1 BNDI0 BURST0 SCC0 SCAN0 00 0000 0000 ADMODB A/D mode register B A1H CLK2 CLK1 CLK0 - ENDAC1 ENDAC0 BSA1 BSA0 00 000x 0000 AD0BH A/D_0 boundary high register BBH FF 1111 1111 AD0BL A/D_0 boundary low register A6H 00 0000 0000 AD0DAT0 A/D_0 data register 0 C5H 00 0000 0000 AD0DAT1 A/D_0 data register 1 C6H 00 0000 0000 AD0DAT2 A/D_0 data register 2 C7H 00 0000 0000 A/D_0 data register 3 F4H 00 0000 0000 AD1BH A/D_1 boundary high register C4H FF 1111 1111 AD1BL A/D_1 boundary low register BCH 00 0000 0000 AD1DAT0 A/D_1 data register 0 D5H 00 0000 0000 AD1DAT1 A/D_1 data register 1 D6H 00 0000 0000 AD1DAT2 A/D_1 data register 2 D7H 00 0000 0000 AD1DAT3 A/D_1 data register 3 F5H 00 0000 0000 AUXR1 Auxiliary function register A2H 00 0000 00x0 B* B register F0H 00 0000 0000 BRGR0[2] Baud rate generator rate low BEH 00 0000 0000 BRGR1[2] Baud rate generator rate high BFH 00 0000 0000 xxxx xx00 0000 0000 Bit address CLKLP EBRR ENT1 ENT0 SRST 0 - DPS F7 F6 F5 F4 F3 F2 F1 F0 18 of 77 (c) NXP B.V. 2011. All rights reserved. BRGCON Baud rate generator control BDH - - - - - - SBRGS BRGEN 00[2] CCCRA Capture compare A control register EAH ICECA2 ICECA1 ICECA0 ICESA ICNFA FCOA OCMA1 OCMA0 00 P89LPC933/934/935/936 AD0DAT3 8-bit microcontroller with accelerated two-clock 80C51 core Rev. 8 -- 12 January 2011 All information provided in this document is subject to legal disclaimers. ADINS xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Name Description SFR Bit functions and addresses addr. MSB Reset value LSB Hex Binary CCCRB Capture compare B control register EBH ICECB2 ICECB1 ICECB0 ICESB ICNFB FCOB OCMB1 OCMB0 00 0000 0000 CCCRC Capture compare C control register ECH - - - - - FCOC OCMC1 OCMC0 00 xxxx x000 CCCRD Capture compare D control register EDH - - - - - FCOD OCMD1 OCMD0 00 xxxx x000 CMP1 Comparator 1 control register ACH - - CE1 CP1 CN1 OE1 CO1 CMF1 00[3] xx00 0000 xx00 0000 Comparator 2 control register ADH - - CE2 CP2 CN2 OE2 CO2 CMF2 DEECON Data EEPROM control register F1H EEIF HVERR ECTL1 ECTL0 - - - EADR8 0E 0000 1110 DEEDAT Data EEPROM data register F2H 00 0000 0000 DEEADR Data EEPROM address register F3H 00 0000 0000 DIVM CPU clock divide-by-M control 95H 00 0000 0000 DPTR Data pointer (2 bytes) Data pointer high 83H 00 0000 0000 DPL Data pointer low 82H 00 0000 0000 FMADRH Program flash address high E7H 00 0000 0000 FMADRL Program flash address low E6H 00 0000 0000 70 0111 0000 00 0000 0000 00 0000 0000 00 x000 00x0 00 0000 0000 Program flash control (Read) E4H Program flash control (Write) E4H FMDATA Program flash data E5H I2ADR I2 C slave address register DBH Bit address 19 of 77 (c) NXP B.V. 2011. All rights reserved. I2CON* I2C control register D8H I2DAT I2C DAH I2SCLH Serial clock generator/SCL duty cycle register high data register DDH BUSY - - - HVA HVE SV OI FMCMD. FMCMD. FMCMD. FMCMD. FMCMD. FMCMD. FMCMD. FMCMD. 7 6 5 4 3 2 1 0 I2ADR.6 I2ADR.5 I2ADR.4 I2ADR.3 I2ADR.2 I2ADR.1 I2ADR.0 GC DF DE DD DC DB DA D9 D8 - I2EN STA STO SI AA - CRSEL P89LPC933/934/935/936 DPH 8-bit microcontroller with accelerated two-clock 80C51 core Rev. 8 -- 12 January 2011 All information provided in this document is subject to legal disclaimers. CMP2 00[3] FMCON NXP Semiconductors P89LPC933_934_935_936 Product data sheet Table 6. Special function registers - P89LPC935/936 ...continued * indicates SFRs that are bit addressable. xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Name Description SFR Bit functions and addresses addr. MSB Reset value LSB Hex Binary 00 0000 0000 F8 1111 1000 I2SCLL Serial clock generator/SCL duty cycle register low DCH I2STAT I2C status register D9H ICRAH Input capture A register high ABH 00 0000 0000 ICRAL Input capture A register low AAH 00 0000 0000 ICRBH Input capture B register high AFH 00 0000 0000 ICRBL Input capture B register low AEH 00 0000 0000 00 0000 0000 00[3] 00x0 0000 Bit address Interrupt enable 0 A8H Bit address IEN1* Interrupt enable 1 E8H Bit address STA.3 STA.2 STA.1 STA.0 0 0 0 AF AE AD AC AB AA A9 A8 EA EWDRT EBO ES/ESR ET1 EX1 ET0 EX0 EF EE ED EC EB EA E9 E8 EADEE EST - ECCU ESPI EC EKBI EI2C BF BE BD BC BB BA B9 B8 Interrupt priority 0 B8H - PWDRT PBO PS/PSR PT1 PX1 PT0 PX0 00[3] x000 0000 IP0H Interrupt priority 0 high B7H - PWDRT H PBOH PSH/ PSRH PT1H PX1H PT0H PX0H 00[3] x000 0000 FF FE FD FC FB FA F9 F8 Bit address IP1* Interrupt priority 1 F8H PADEE PST - PCCU PSPI PC PKBI PI2C 00[3] 00x0 0000 IP1H Interrupt priority 1 high F7H PAEEH PSTH - PCCUH PSPIH PCH PKBIH PI2CH 00[3] 00x0 0000 KBIF 00[3] xxxx xx00 20 of 77 (c) NXP B.V. 2011. All rights reserved. KBCON Keypad control register 94H - - - - - - PATN _SEL KBMASK Keypad interrupt mask register 86H 00 0000 0000 KBPATN Keypad pattern register 93H FF 1111 1111 OCRAH Output compare A register high EFH 00 0000 0000 OCRAL Output compare A register low EEH 00 0000 0000 OCRBH Output compare B register high FBH 00 0000 0000 OCRBL Output compare B register low FAH 00 0000 0000 P89LPC933/934/935/936 IP0* 8-bit microcontroller with accelerated two-clock 80C51 core Rev. 8 -- 12 January 2011 All information provided in this document is subject to legal disclaimers. IEN0* STA.4 NXP Semiconductors P89LPC933_934_935_936 Product data sheet Table 6. Special function registers - P89LPC935/936 ...continued * indicates SFRs that are bit addressable. xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Name Description SFR Bit functions and addresses addr. MSB Reset value LSB Hex Binary OCRCH Output compare C register high FDH 00 0000 0000 OCRCL Output compare C register low FCH 00 0000 0000 OCRDH Output compare D register high FFH 00 0000 0000 OCRDL Output compare D register low FEH 00 0000 0000 P0* Port 0 Bit address Bit address P1* Port 1 90H Bit address Port 2 P3* Port 3 A0H Bit address P0M1 P0M2 B0H Port 0 output mode 1 84H Port 0 output mode 2 85H 86 85 84 83 82 81 80 CMP1 /KB6 CMPREF /KB5 CIN1A /KB4 CIN1B /KB3 CIN2A /KB2 CIN2B /KB1 CMP2 /KB0 97 96 95 94 93 92 91 90 OCC OCB RST INT1 INT0/ SDA T0/SCL RXD TXD A7 A6 A5 A4 A3 A2 A1 A0 ICA OCA SPICLK SS MISO MOSI OCD ICB B7 B6 B5 B4 B3 B2 B1 B0 - - - - - - XTAL1 XTAL2 [3] [3] [3] [3] (P0M1.7) (P0M1.6) (P0M1.5) (P0M1.4) (P0M1.3) (P0M1.2) (P0M1.1) (P0M1.0) FF[3] 1111 1111 (P0M2.7) (P0M2.6) (P0M2.5) (P0M2.4) (P0M2.3) (P0M2.2) (P0M2.1) (P0M2.0) 00[3] 0000 0000 D3[3] 11x1 xx11 00x0 xx00 P1M1 Port 1 output mode 1 91H (P1M1.7) (P1M1.6) - (P1M1.4) (P1M1.3) (P1M1.2) (P1M1.1) (P1M1.0) P1M2 Port 1 output mode 2 92H (P1M2.7) (P1M2.6) - (P1M2.4) (P1M2.3) (P1M2.2) (P1M2.1) (P1M2.0) 00[3] P2M1 P2M2 Port 2 output mode 1 A4H Port 2 output mode 2 A5H (P2M1.7) (P2M1.6) (P2M1.5) (P2M1.4) (P2M1.3) (P2M1.2) (P2M1.1) (P2M1.0) FF[3] 1111 1111 (P2M2.7) (P2M2.6) (P2M2.5) (P2M2.4) (P2M2.3) (P2M2.2) (P2M2.1) (P2M2.0) 00[3] 0000 0000 03[3] xxxx xx11 21 of 77 (c) NXP B.V. 2011. All rights reserved. P3M1 Port 3 output mode 1 B1H - - - - - - (P3M1.1) (P3M1.0) P3M2 Port 3 output mode 2 B2H - - - - - - (P3M2.1) (P3M2.0) 00[3] xxxx xx00 PCON Power control register 87H SMOD1 SMOD0 BOPD BOI GF1 GF0 PMOD1 PCONA Power control register A B5H PSW* Program status word D0H PT0AD Port 0 digital input disable F6H - - Bit address RTCPD DEEPD VCPD ADPD D7 D6 D5 D4 CY AC F0 RS1 I2PD PMOD0 00 0000 0000 00[3] 0000 0000 SPPD SPD CCUPD D3 D2 D1 D0 RS0 OV F1 P 00 0000 0000 - 00 xx00 000x PT0AD.5 PT0AD.4 PT0AD.3 PT0AD.2 PT0AD.1 P89LPC933/934/935/936 P2* 87 T1/KB7 8-bit microcontroller with accelerated two-clock 80C51 core Rev. 8 -- 12 January 2011 All information provided in this document is subject to legal disclaimers. 80H NXP Semiconductors P89LPC933_934_935_936 Product data sheet Table 6. Special function registers - P89LPC935/936 ...continued * indicates SFRs that are bit addressable. xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Name Description SFR Bit functions and addresses addr. MSB Reset value LSB RSTSRC Reset source register DFH - - BOF POF R_BK R_WD R_SF R_EX RTCCON Real-time clock control D1H RTCF RTCS1 RTCS0 - - - ERTC RTCEN RTCH RTCL Real-time clock register high Real-time clock register low Hex Binary [4] 60[3][5] 011x xx00 D2H 00[5] 0000 0000 D3H 00[5] 0000 0000 SADDR Serial port address register A9H 00 0000 0000 SADEN Serial port address enable B9H 00 0000 0000 SBUF Serial Port data buffer register 99H xx xxxx xxxx Bit address 9F 9E 9D 9C 9B 9A 99 98 98H SM0/FE SM1 SM2 REN TB8 RB8 TI RI 00 0000 0000 Serial port extended status register BAH DBMOD INTLO CIDIS DBISEL FE BR OE STINT 00 0000 0000 SP Stack pointer 81H 07 0000 0111 SPCTL SPI control register E2H SSIG SPEN DORD MSTR CPOL CPHA SPR1 SPR0 04 0000 0100 SPSTAT SPI status register E1H SPIF WCOL - - - - - - 00 00xx xxxx SPDAT SPI data register E3H 00 0000 0000 TAMOD Timer 0 and 1 auxiliary mode 8FH 00 xxx0 xxx0 8F 8E 8D 8C 8B 8A 89 88 TCON* Timer 0 and 1 control 88H TF1 TR1 TF0 TR0 IE1 IT1 IE0 IT0 00 0000 0000 TCR20* CCU control register 0 C8H PLEEN HLTRN HLTEN ALTCD ALTAB TDIR2 TMOD21 TMOD20 00 0000 0000 TCR21 CCU control register 1 F9H TCOU2 - - - PLLDV.3 PLLDV.2 PLLDV.1 PLLDV.0 00 0xxx 0000 TH0 Timer 0 high 8CH 00 0000 0000 TH1 Timer 1 high 8DH 00 0000 0000 TH2 CCU timer high CDH 00 0000 0000 TICR2 CCU interrupt control register C9H TOIE2 TOCIE2 D TIFR2 CCU interrupt flag register E9H TOIF2 TOCF2D TOCF2C TISE2 CCU interrupt status encode register DEH - TL0 Timer 0 low TL1 Timer 1 low Bit address - - - - - T0M2 TOCIE2B TOCIE2A - TICIE2B TICIE2A 00 0000 0x00 TOCF2B TOCF2A - TICF2B TICF2A 00 0000 0x00 - - ENCINT. 2 ENCINT. 1 ENCINT. 00 0 xxxx x000 8AH 00 0000 0000 8BH 00 0000 0000 - TOCIE2 C T1M2 - P89LPC933/934/935/936 22 of 77 (c) NXP B.V. 2011. All rights reserved. Serial port control SSTAT 8-bit microcontroller with accelerated two-clock 80C51 core Rev. 8 -- 12 January 2011 All information provided in this document is subject to legal disclaimers. SCON* - NXP Semiconductors P89LPC933_934_935_936 Product data sheet Table 6. Special function registers - P89LPC935/936 ...continued * indicates SFRs that are bit addressable. xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Name Description SFR Bit functions and addresses addr. MSB Reset value LSB Hex Binary 00 0000 0000 T0M0 00 0000 0000 CCU timer low CCH TMOD Timer 0 and 1 mode 89H TOR2H CCU reload register high CFH 00 0000 0000 TOR2L CCU reload register low CEH 00 0000 0000 TPCR2H Prescaler control register high CBH TPCR2L Prescaler control register low CAH TRIM Internal oscillator trim register 96H RCCLK ENCLK TRIM.5 TRIM.4 TRIM.3 TRIM.2 TRIM.1 TRIM.0 [6] [5] WDCON Watchdog control register A7H PRE2 PRE1 PRE0 - - WDRUN WDTOF WDCLK [7] [5] WDL Watchdog load C1H WFEED1 Watchdog feed 1 C2H WFEED2 Watchdog feed 2 C3H - T1C/T - T1M1 - T1M0 - T0GATE - T0C/T - T0M1 TPCR2H. TPCR2H. 00 1 0 TPCR2L. TPCR2L. TPCR2L. TPCR2L. TPCR2L. TPCR2L. TPCR2L. TPCR2L. 00 7 6 5 4 3 2 1 0 FF xxxx xx00 0000 0000 1111 1111 Unimplemented bits in SFRs (labeled '-') are X (unknown) at all times. Unless otherwise specified, ones should not be written to these bits since they may be used for other purposes in future derivatives. The reset values shown for these bits are logic 0s although they are unknown when read. [2] All ports are in input only (high-impedance) state after power-up. [3] BRGR1 and BRGR0 must only be written if BRGEN in BRGCON SFR is logic 0. If any are written while BRGEN = 1, the result is unpredictable. [4] The RSTSRC register reflects the cause of the P89LPC933/934/935/936 reset. Upon a power-up reset, all reset source flags are cleared except POF and BOF; the power-on reset value is xx11 0000. [5] After reset, the value is 1110 01x1, i.e., PRE2 to PRE0 are all logic 1, WDRUN = 1 and WDCLK = 1. WDTOF bit is logic 1 after watchdog reset and is logic 0 after power-on reset. Other resets will not affect WDTOF. [6] On power-on reset, the TRIM SFR is initialized with a factory preprogrammed value. Other resets will not cause initialization of the TRIM register. [7] The only reset source that affects these SFRs is power-on reset. 23 of 77 (c) NXP B.V. 2011. All rights reserved. P89LPC933/934/935/936 [1] 8-bit microcontroller with accelerated two-clock 80C51 core Rev. 8 -- 12 January 2011 All information provided in this document is subject to legal disclaimers. TL2 T1GATE NXP Semiconductors P89LPC933_934_935_936 Product data sheet Table 6. Special function registers - P89LPC935/936 ...continued * indicates SFRs that are bit addressable. P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 8.2 Enhanced CPU The P89LPC933/934/935/936 uses an enhanced 80C51 CPU which runs at six times the speed of standard 80C51 devices. A machine cycle consists of two CPU clock cycles, and most instructions execute in one or two machine cycles. 8.3 Clocks 8.3.1 Clock definitions The P89LPC933/934/935/936 device has several internal clocks as defined below: OSCCLK -- Input to the DIVM clock divider. OSCCLK is selected from one of four clock sources (see Figure 8) and can also be optionally divided to a slower frequency (see Section 8.8 "CCLK modification: DIVM register"). Remark: fosc is defined as the OSCCLK frequency. CCLK -- CPU clock; output of the clock divider. There are two CCLK cycles per machine cycle, and most instructions are executed in one to two machine cycles (two or four CCLK cycles). RCCLK -- The internal 7.373 MHz RC oscillator output. PCLK -- Clock for the various peripheral devices and is CCLK2. 8.3.2 CPU clock (OSCCLK) The P89LPC933/934/935/936 provides several user-selectable oscillator options in generating the CPU clock. This allows optimization for a range of needs from high precision to lowest possible cost. These options are configured when the flash is programmed and include an on-chip watchdog oscillator, an on-chip RC oscillator, an oscillator using an external crystal, or an external clock source. The crystal oscillator can be optimized for low, medium, or high frequency crystals covering a range from 20 kHz to 18 MHz. 8.3.3 Low speed oscillator option This option supports an external crystal in the range of 20 kHz to 100 kHz. Ceramic resonators are also supported in this configuration. 8.3.4 Medium speed oscillator option This option supports an external crystal in the range of 100 kHz to 4 MHz. Ceramic resonators are also supported in this configuration. 8.3.5 High speed oscillator option This option supports an external crystal in the range of 4 MHz to 18 MHz. Ceramic resonators are also supported in this configuration. 8.3.6 Clock output The P89LPC933/934/935/936 supports a user-selectable clock output function on the XTAL2/CLKOUT pin when crystal oscillator is not being used. This condition occurs if another clock source has been selected (on-chip RC oscillator, watchdog oscillator, P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 24 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core external clock input on X1) and if the RTC is not using the crystal oscillator as its clock source. This allows external devices to synchronize to the P89LPC933/934/935/936. This output is enabled by the ENCLK bit in the TRIM register. The frequency of this clock output is 12 that of the CCLK. If the clock output is not needed in Idle mode, it may be turned off prior to entering Idle, saving additional power. 8.4 On-chip RC oscillator option The P89LPC933/934/935/936 has a 6-bit TRIM register that can be used to tune the frequency of the RC oscillator. During reset, the TRIM value is initialized to a factory preprogrammed value to adjust the oscillator frequency to 7.373 MHz 1 % at room temperature. End-user applications can write to the TRIM register to adjust the on-chip RC oscillator to other frequencies. 8.5 Watchdog oscillator option The watchdog has a separate oscillator which has a frequency of 400 kHz. This oscillator can be used to save power when a high clock frequency is not needed. 8.6 External clock input option In this configuration, the processor clock is derived from an external source driving the P3.1/XTAL1 pin. The rate may be from 0 Hz up to 18 MHz. The P3.0/XTAL2 pin may be used as a standard port pin or a clock output. When using an oscillator frequency above 12 MHz, the reset input function of P1.5 must be enabled. An external circuit is required to hold the device in reset at power-up until VDD has reached its specified level. When system power is removed VDD will fall below the minimum specified operating voltage. When using an oscillator frequency above 12 MHz, in some applications, an external brownout detect circuit may be required to hold the device in reset when VDD falls below the minimum specified operating voltage. P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 25 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core XTAL1 XTAL2 HIGH FREQUENCY MEDIUM FREQUENCY LOW FREQUENCY RTC ADC1 ADC0 (P89LPC935/936) OSCCLK DIVM CCLK CPU RCCLK RC OSCILLATOR /2 (7.3728 MHz 1 %) PCLK WDT WATCHDOG OSCILLATOR PCLK (400 kHz +30 % -20 %) TIMER 0 AND TIMER 1 I2C-BUS 32 x PLL SPI UART CCU (P89LPC935/936) 002aab079 Fig 8. P89LPC933_934_935_936 Product data sheet Block diagram of oscillator control All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 26 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 8.7 CCLK wake-up delay The P89LPC933/934/935/936 has an internal wake-up timer that delays the clock until it stabilizes depending on the clock source used. If the clock source is any of the three crystal selections (low, medium and high frequencies) the delay is 992 OSCCLK cycles plus 60 s to 100 s. If the clock source is either the internal RC oscillator, watchdog oscillator, or external clock, the delay is 224 OSCCLK cycles plus 60 s to 100 s. 8.8 CCLK modification: DIVM register The OSCCLK frequency can be divided down up to 510 times by configuring a dividing register, DIVM, to generate CCLK. This feature makes it possible to temporarily run the CPU at a lower rate, reducing power consumption. By dividing the clock, the CPU can retain the ability to respond to events that would not exit Idle mode by executing its normal program at a lower rate. This can also allow bypassing the oscillator start-up time in cases where Power-down mode would otherwise be used. The value of DIVM may be changed by the program at any time without interrupting code execution. 8.9 Low power select The P89LPC933/934/935/936 is designed to run at 18 MHz (CCLK) maximum. However, if CCLK is 8 MHz or slower, the CLKLP SFR bit (AUXR1.7) can be set to logic 1 to lower the power consumption further. On any reset, CLKLP is logic 0 allowing highest performance access. This bit can then be set in software if CCLK is running at 8 MHz or slower. 8.10 Memory organization The various P89LPC933/934/935/936 memory spaces are as follows: * DATA 128 bytes of internal data memory space (00H:7FH) accessed via direct or indirect addressing, using instructions other than MOVX and MOVC. All or part of the Stack may be in this area. * IDATA Indirect Data. 256 bytes of internal data memory space (00H:FFH) accessed via indirect addressing using instructions other than MOVX and MOVC. All or part of the Stack may be in this area. This area includes the DATA area and the 128 bytes immediately above it. * SFR Selected CPU registers and peripheral control and status registers, accessible only via direct addressing. * XDATA (P89LPC935/936) `External' Data or Auxiliary RAM. Duplicates the classic 80C51 64 kB memory space addressed via the MOVX instruction using the SPTR, R0, or R1. All or part of this space could be implemented on-chip. The P89LPC935/936 has 512 bytes of on-chip XDATA memory. P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 27 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core * CODE 64 kB of code memory space, accessed as part of program execution and via the MOVC instruction. The P89LPC933/934/935/936 have 4 KB/8 kB/16 kB of on-chip Code memory. The P89LPC935/936 also has 512 bytes of on-chip data EEPROM that is accessed via SFRs (see Section 8.27 "Data EEPROM (P89LPC935/936)"). 8.11 Data RAM arrangement The 768 bytes of on-chip RAM are organized as shown in Table 7. Table 7. On-chip data memory usages Type Data RAM Size (bytes) DATA Memory that can be addressed directly and indirectly 128 IDATA Memory that can be addressed indirectly 256 XDATA Auxiliary (`External Data') on-chip memory that is accessed using the MOVX instructions (P89LPC935/936) 512 8.12 Interrupts The P89LPC933/934/935/936 uses a four priority level interrupt structure. This allows great flexibility in controlling the handling of the many interrupt sources. The P89LPC933/934/935/936 supports 15 interrupt sources: external interrupts 0 and 1, timers 0 and 1, serial port Tx, serial port Rx, combined serial port Rx/Tx, brownout detect, watchdog/Real-Time clock, I2C-bus, keyboard, comparators 1 and 2, SPI, CCU, data EEPROM write/ADC completion. Each interrupt source can be individually enabled or disabled by setting or clearing a bit in the interrupt enable registers IEN0 or IEN1. The IEN0 register also contains a global disable bit, EA, which disables all interrupts. Each interrupt source can be individually programmed to one of four priority levels by setting or clearing bits in the interrupt priority registers IP0, IP0H, IP1, and IP1H. An interrupt service routine in progress can be interrupted by a higher priority interrupt, but not by another interrupt of the same or lower priority. The highest priority interrupt service cannot be interrupted by any other interrupt source. If two requests of different priority levels are pending at the start of an instruction, the request of higher priority level is serviced. If requests of the same priority level are pending at the start of an instruction, an internal polling sequence determines which request is serviced. This is called the arbitration ranking. Remark: The arbitration ranking is only used to resolve pending requests of the same priority level. 8.12.1 External interrupt inputs The P89LPC933/934/935/936 has two external interrupt inputs as well as the Keypad Interrupt function. The two interrupt inputs are identical to those present on the standard 80C51 microcontrollers. P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 28 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core These external interrupts can be programmed to be level-triggered or edge-triggered by setting or clearing bit IT1 or IT0 in register TCON. In edge-triggered mode, if successive samples of the INTn pin show a HIGH in one cycle and a LOW in the next cycle, the interrupt request flag IEn in TCON is set, causing an interrupt request. If an external interrupt is enabled when the P89LPC933/934/935/936 is put into Power-down or Idle mode, the interrupt will cause the processor to wake-up and resume operation. Refer to Section 8.15 "Power reduction modes" for details. IE0 EX0 IE1 EX1 BOF EBO RTCF ERTC (RTCCON.1) WDOVF wake-up (if in power-down) KBIF EKBI EWDRT CMF2 CMF1 EC EA (IE0.7) TF0 ET0 TF1 ET1 TI & RI/RI ES/ESR TI EST interrupt to CPU SI EI2C SPIF ESPI any CCU interrupt(1) ECCU EEIF(2) ENADCI0(2) ADCI0(2) ENADCI1 ADCI1 ENBI0(2) BNDI0(2) ENBI1 BNDI1 EADEE (P89LPC935) EAD (P89LPC933/934) 002aab081 (1) See Section 8.19 "CCU (P89LPC935/936)" (2) P89LPC935/936 Fig 9. Interrupt sources, interrupt enables, and power-down wake-up sources P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 29 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 8.13 I/O ports The P89LPC933/934/935/936 has four I/O ports: Port 0, Port 1, Port 2, and Port 3. Ports 0, 1 and 2 are 8-bit ports, and Port 3 is a 2-bit port. The exact number of I/O pins available depends upon the clock and reset options chosen, as shown in Table 8. Table 8. Number of I/O pins available Clock source Reset option Number of I/O pins (28-pin package) On-chip oscillator or watchdog oscillator No external reset (except during power-up) 26 External RST pin supported 25 No external reset (except during power-up) 25 External RST pin supported[1] 24 No external reset (except during power-up) 24 External RST pin supported[1] 23 External clock input Low/medium/high speed oscillator (external crystal or resonator) [1] Required for operation above 12 MHz. 8.13.1 Port configurations All but three I/O port pins on the P89LPC933/934/935/936 may be configured by software to one of four types on a bit-by-bit basis. These are: quasi-bidirectional (standard 80C51 port outputs), push-pull, open drain, and input-only. Two configuration registers for each port select the output type for each port pin. 1. P1.5 (RST) can only be an input and cannot be configured. 2. P1.2 (SCL/T0) and P1.3 (SDA/INT0) may only be configured to be either input-only or open-drain. 8.13.1.1 Quasi-bidirectional output configuration Quasi-bidirectional output type can be used as both an input and output without the need to reconfigure the port. This is possible because when the port outputs a logic HIGH, it is weakly driven, allowing an external device to pull the pin LOW. When the pin is driven LOW, it is driven strongly and able to sink a fairly large current. These features are somewhat similar to an open-drain output except that there are three pull-up transistors in the quasi-bidirectional output that serve different purposes. The P89LPC933/934/935/936 is a 3 V device, but the pins are 5 V-tolerant. In quasi-bidirectional mode, if a user applies 5 V on the pin, there will be a current flowing from the pin to VDD, causing extra power consumption. Therefore, applying 5 V in quasi-bidirectional mode is discouraged. A quasi-bidirectional port pin has a Schmitt trigger input that also has a glitch suppression circuit. 8.13.1.2 Open-drain output configuration The open-drain output configuration turns off all pull-ups and only drives the pull-down transistor of the port driver when the port latch contains a logic 0. To be used as a logic output, a port configured in this manner must have an external pull-up, typically a resistor tied to VDD. P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 30 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core An open-drain port pin has a Schmitt trigger input that also has a glitch suppression circuit. 8.13.1.3 Input-only configuration The input-only port configuration has no output drivers. It is a Schmitt trigger input that also has a glitch suppression circuit. 8.13.1.4 Push-pull output configuration The push-pull output configuration has the same pull-down structure as both the open-drain and the quasi-bidirectional output modes, but provides a continuous strong pull-up when the port latch contains a logic 1. The push-pull mode may be used when more source current is needed from a port output. A push-pull port pin has a Schmitt trigger input that also has a glitch suppression circuit. 8.13.2 Port 0 analog functions The P89LPC933/934/935/936 incorporates two Analog Comparators. In order to give the best analog function performance and to minimize power consumption, pins that are being used for analog functions must have the digital outputs and digital inputs disabled. Digital outputs are disabled by putting the port output into the Input-Only (high-impedance) mode. Digital inputs on Port 0 may be disabled through the use of the PT0AD register, bits 1:5. On any reset, PT0AD[1:5] defaults to logic 0s to enable digital functions. 8.13.3 Additional port features After power-up, all pins are in Input-Only mode. Remark: Please note that this is different from the LPC76x series of devices. * After power-up, all I/O pins except P1.5, may be configured by software. * Pin P1.5 is input only. Pins P1.2 and P1.3 and are configurable for either input-only or open-drain. Every output on the P89LPC933/934/935/936 has been designed to sink typical LED drive current. However, there is a maximum total output current for all ports which must not be exceeded. Please refer to Table 11 "Static characteristics" for detailed specifications. All ports pins that can function as an output have slew rate controlled outputs to limit noise generated by quickly switching output signals. The slew rate is factory-set to approximately 10 ns rise and fall times. 8.14 Power monitoring functions The P89LPC933/934/935/936 incorporates power monitoring functions designed to prevent incorrect operation during initial power-up and power loss or reduction during operation. This is accomplished with two hardware functions: Power-on detect and brownout detect. P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 31 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 8.14.1 Brownout detection The brownout detect function determines if the power supply voltage drops below a certain level. The default operation is for a brownout detection to cause a processor reset, however it may alternatively be configured to generate an interrupt. Brownout detection may be enabled or disabled in software. If brownout detection is enabled the brownout condition occurs when VDD falls below the brownout trip voltage, Vbo (see Table 11 "Static characteristics"), and is negated when VDD rises above Vbo. If the P89LPC933/934/935/936 device is to operate with a power supply that can be below 2.7 V, BOE should be left in the unprogrammed state so that the device can operate at 2.4 V, otherwise continuous brownout reset may prevent the device from operating. For correct activation of brownout detect, the VDD rise and fall times must be observed. Please see Table 11 "Static characteristics" for specifications. 8.14.2 Power-on detection The power-on detect has a function similar to the brownout detect, but is designed to work as power comes up initially, before the power supply voltage reaches a level where brownout detect can work. The POF flag in the RSTSRC register is set to indicate an initial power-up condition. The POF flag will remain set until cleared by software. 8.15 Power reduction modes The P89LPC933/934/935/936 supports three different power reduction modes. These modes are Idle mode, Power-down mode, and total Power-down mode. 8.15.1 Idle mode Idle mode leaves peripherals running in order to allow them to activate the processor when an interrupt is generated. Any enabled interrupt source or reset may terminate Idle mode. 8.15.2 Power-down mode The Power-down mode stops the oscillator in order to minimize power consumption. The P89LPC933/934/935/936 exits Power-down mode via any reset, or certain interrupts. In Power-down mode, the power supply voltage may be reduced to the RAM keep-alive voltage VRAM. This retains the RAM contents at the point where Power-down mode was entered. SFR contents are not guaranteed after VDD has been lowered to VDDR, therefore it is highly recommended to wake-up the processor via reset in this case. VDD must be raised to within the operating range before the Power-down mode is exited. Some chip functions continue to operate and draw power during Power-down mode, increasing the total power used during power-down. These include: brownout detect, watchdog timer, Comparators (note that Comparators can be powered-down separately), and RTC/system timer. The internal RC oscillator is disabled unless both the RC oscillator has been selected as the system clock and the RTC is enabled. P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 32 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 8.15.3 Total Power-down mode This is the same as Power-down mode except that the brownout detection circuitry and the voltage comparators are also disabled to conserve additional power. The internal RC oscillator is disabled unless both the RC oscillator has been selected as the system clock and the RTC is enabled. If the internal RC oscillator is used to clock the RTC during power-down, there will be high power consumption. Please use an external low frequency clock to achieve low power with the RTC running during power-down. 8.16 Reset The P1.5/RST pin can function as either a LOW-active reset input or as a digital input, P1.5. The Reset Pin Enable (RPE) bit in UCFG1, when set to logic 1, enables the external reset input function on P1.5. When cleared, P1.5 may be used as an input pin. Remark: During a power-up sequence, the RPE selection is overridden and this pin will always functions as a reset input. An external circuit connected to this pin should not hold this pin LOW during a power-on sequence as this will keep the device in reset. After power-up this input will function either as an external reset input or as a digital input as defined by the RPE bit. Only a power-up reset will temporarily override the selection defined by RPE bit. Other sources of reset will not override the RPE bit. When this pin functions as a reset input, an internal pull-up resistance is connected (see Table 11 "Static characteristics"). Reset can be triggered from the following sources: * * * * * * External reset pin (during power-up or if user configured via UCFG1). Power-on detect. Brownout detect. Watchdog timer. Software reset. UART break character detect reset. For every reset source, there is a flag in the reset register, RSTSRC. The user can read this register to determine the most recent reset source. These flag bits can be cleared in software by writing a logic 0 to the corresponding bit. More than one flag bit may be set: * During a power-on reset, both POF and BOF are set but the other flag bits are cleared. * For any other reset, previously set flag bits that have not been cleared will remain set. 8.16.1 Reset vector Following reset, the P89LPC933/934/935/936 will fetch instructions from either address 0000H or the boot address. The boot address is formed by using the boot vector as the high byte of the address and the low byte of the address = 00H. The boot address will be used if a UART break reset occurs, or the non-volatile boot status bit (BOOTSTAT.0) = 1, or the device is forced into ISP mode during power-on (see P89LPC933/934/935/936 User manual). Otherwise, instructions will be fetched from address 0000H. P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 33 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 8.17 Timers/counters 0 and 1 The P89LPC933/934/935/936 has two general purpose counter/timers which are upward compatible with the standard 80C51 Timer 0 and Timer 1. Both can be configured to operate either as timers or event counter. An option to automatically toggle the T0 and/or T1 pins upon timer overflow has been added. In the `timer' function, the register is incremented every machine cycle. In the `counter' function, the register is incremented in response to a 1-to-0 transition at its corresponding external input pin, T0 or T1. In this function, the external input is sampled once during every machine cycle. Timer 0 and Timer 1 have five operating modes (modes 0, 1, 2, 3 and 6). Modes 0, 1, 2 and 6 are the same for both timers/counters. Mode 3 is different. 8.17.1 Mode 0 Putting either timer into Mode 0 makes it look like an 8048 timer, which is an 8-bit counter with a divide-by-32 prescaler. In this mode, the timer register is configured as a 13-bit register. Mode 0 operation is the same for Timer 0 and Timer 1. 8.17.2 Mode 1 Mode 1 is the same as Mode 0, except that all 16 bits of the timer register are used. 8.17.3 Mode 2 Mode 2 configures the timer register as an 8-bit counter with automatic reload. Mode 2 operation is the same for Timer 0 and Timer 1. 8.17.4 Mode 3 When Timer 1 is in Mode 3 it is stopped. Timer 0 in Mode 3 forms two separate 8-bit counters and is provided for applications that require an extra 8-bit timer. When Timer 1 is in Mode 3 it can still be used by the serial port as a baud rate generator. 8.17.5 Mode 6 In this mode, the corresponding timer can be changed to a PWM with a full period of 256 timer clocks. 8.17.6 Timer overflow toggle output Timers 0 and 1 can be configured to automatically toggle a port output whenever a timer overflow occurs. The same device pins that are used for the T0 and T1 count inputs are also used for the timer toggle outputs. The port outputs will be a logic 1 prior to the first timer overflow when this mode is turned on. 8.18 RTC/system timer The P89LPC933/934/935/936 has a simple RTC that allows a user to continue running an accurate timer while the rest of the device is powered-down. The RTC can be a wake-up or an interrupt source. The RTC is a 23-bit down counter comprised of a 7-bit prescaler and a 16-bit loadable down counter. When it reaches all logic 0s, the counter will be reloaded again and the RTCF flag will be set. The clock source for this counter can be either the CPU clock (CCLK) or the XTAL oscillator, provided that the XTAL oscillator is P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 34 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core not being used as the CPU clock. If the XTAL oscillator is used as the CPU clock, then the RTC will use CCLK as its clock source. Only power-on reset will reset the RTC and its associated SFRs to the default state. 8.19 CCU (P89LPC935/936) This unit features: * A 16-bit timer with 16-bit reload on overflow. * Selectable clock, with prescaler to divide clock source by any integral number between 1 and 1024. * * * * Four compare/PWM outputs with selectable polarity. Symmetrical/asymmetrical PWM selection. Two capture inputs with event counter and digital noise rejection filter. Seven interrupts with common interrupt vector (one overflow, two capture, four compare). * Safe 16-bit read/write via shadow registers. 8.19.1 CCU clock The CCU runs on the CCUCLK, which is either PCLK in basic timer mode, or the output of a Phase-Locked Loop (PLL). The PLL is designed to use a clock source between 0.5 MHz to 1 MHz that is multiplied by 32 to produce a CCUCLK between 16 MHz and 32 MHz in PWM mode (asymmetrical or symmetrical). The PLL contains a 4-bit divider to help divide PCLK into a frequency between 0.5 MHz and 1 MHz. 8.19.2 CCUCLK prescaling This CCUCLK can further be divided down by a prescaler. The prescaler is implemented as a 10-bit free-running counter with programmable reload at overflow. 8.19.3 Basic timer operation The timer is a free-running up/down counter with a direction control bit. If the timer counting direction is changed while the counter is running, the count sequence will be reversed. The timer can be written or read at any time. When a reload occurs, the CCU Timer Overflow Interrupt Flag will be set, and an interrupt generated if enabled. The 16-bit CCU timer may also be used as an 8-bit up/down timer. 8.19.4 Output compare There are four output compare channels A, B, C and D. Each output compare channel needs to be enabled in order to operate and the user will have to set the associated I/O pin to the desired output mode to connect the pin. When the contents of the timer matches that of a capture compare control register, the Timer Output Compare Interrupt Flag (TOCFx) becomes set. An interrupt will occur if enabled. 8.19.5 Input capture Input capture is always enabled. Each time a capture event occurs on one of the two input capture pins, the contents of the timer is transferred to the corresponding 16-bit input capture register. The capture event can be programmed to be either rising or falling edge triggered. A simple noise filter can be enabled on the input capture by enabling the Input P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 35 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core Capture Noise Filter bit. If set, the capture logic needs to see four consecutive samples of the same value in order to recognize an edge as a capture event. An event counter can be set to delay a capture by a number of capture events. 8.19.6 PWM operation PWM operation has two main modes, symmetrical and asymmetrical. In asymmetrical PWM operation the CCU timer operates in down-counting mode regardless of the direction control bit. In symmetrical mode, the timer counts up/down alternately. The main difference from basic timer operation is the operation of the compare module, which in PWM mode is used for PWM waveform generation. As with basic timer operation, when the PWM (compare) pins are connected to the compare logic, their logic state remains unchanged. However, since bit FCO is used to hold the halt value, only a compare event can change the state of the pin. TOR2 compare value timer value 0x0000 non-inverted inverted 002aaa893 Fig 10. Asymmetrical PWM, down-counting mode TOR2 compare value timer value 0 non-inverted inverted 002aaa894 Fig 11. Symmetrical PWM P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 36 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 8.19.7 Alternating output mode In asymmetrical mode, the user can set up PWM channels A/B and C/D as alternating pairs for bridge drive control. In this mode the output of these PWM channels are alternately gated on every counter cycle. TOR2 COMPARE VALUE A (or C) COMPARE VALUE B (or D) TIMER VALUE 0 PWM OUTPUT (OCA or OCC) PWM OUTPUT (OCB or OCD) 002aaa895 Fig 12. Alternate output mode 8.19.8 PLL operation The PWM module features a PLL that can be used to generate a CCUCLK frequency between 16 MHz and 32 MHz. At this frequency the PWM module provides ultrasonic PWM frequency with 10-bit resolution provided that the crystal frequency is 1 MHz or higher. The PLL is fed an input signal from 0.5 MHz to 1 MHz and generates an output signal of 32 times the input frequency. This signal is used to clock the timer. The user will have to set a divider that scales PCLK by a factor from 1 to 16. This divider is found in the SFR register TCR21. The PLL frequency can be expressed as shown in Equation 1. PCLK PLL frequency = -----------------(N + 1) Where: N is the value of PLLDV.3 to PLLDV.0. (1) Since N ranges from 0 to 15, the CCLK frequency can be in the range of PCLK to PCLK16. P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 37 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 8.19.9 CCU interrupts There are seven interrupt sources on the CCU which share a common interrupt vector. EA (IEN0.7) ECCU (IEN1.4) TOIE2 (TICR2.7) TOIF2 (TIFR2.7) TICIE2A (TICR2.0) TICF2A (TIFR2.0) TICIE2B (TICR2.1) TICF2B (TIFR2.1) TOCIE2A (TICR2.3) TOCF2A (TIFR2.3) interrupt to CPU other interrupt sources TOCIE2B (TICR2.4) TOCF2B (TIFR2.4) TOCIE2C (TICR2.5) TOCF2C (TIFR2.5) TOCIE2D (TICR2.6) TOCF2D (TIFR2.6) ENCINT.0 PRIORITY ENCODER ENCINT.1 ENCINT.2 002aaa896 Fig 13. Capture/compare unit interrupts 8.20 UART The P89LPC933/934/935/936 has an enhanced UART that is compatible with the conventional 80C51 UART except that Timer 2 overflow cannot be used as a baud rate source. The P89LPC933/934/935/936 does include an independent baud rate generator. The baud rate can be selected from the oscillator (divided by a constant), Timer 1 overflow, or the independent baud rate generator. In addition to the baud rate generation, enhancements over the standard 80C51 UART include Framing Error detection, automatic address recognition, selectable double buffering and several interrupt options. The UART can be operated in four modes: shift register, 8-bit UART, 9-bit UART, and CPU clock or CPU clock . 32 16 8.20.1 Mode 0 Serial data enters and exits through RXD. TXD outputs the shift clock. 8 bits are transmitted or received, LSB first. The baud rate is fixed at 116 of the CPU clock frequency. P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 38 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 8.20.2 Mode 1 10 bits are transmitted (through TXD) or received (through RXD): a start bit (logic 0), 8 data bits (LSB first), and a stop bit (logic 1). When data is received, the stop bit is stored in RB8 in special function register SCON. The baud rate is variable and is determined by the Timer 1 overflow rate or the baud rate generator (described in Section 8.20.5 "Baud rate generator and selection"). 8.20.3 Mode 2 11 bits are transmitted (through TXD) or received (through RXD): start bit (logic 0), 8 data bits (LSB first), a programmable 9th data bit, and a stop bit (logic 1). When data is transmitted, the 9th data bit (TB8 in SCON) can be assigned the value of logic 0 or logic 1. Or, for example, the parity bit (P, in the PSW) could be moved into TB8. When data is received, the 9th data bit goes into RB8 in special function register SCON, while the stop bit is not saved. The baud rate is programmable to either 116 or 132 of the CPU clock frequency, as determined by the SMOD1 bit in PCON. 8.20.4 Mode 3 11 bits are transmitted (through TXD) or received (through RXD): a start bit (logic 0), 8 data bits (LSB first), a programmable 9th data bit, and a stop bit (logic 1). In fact, Mode 3 is the same as Mode 2 in all respects except baud rate. The baud rate in Mode 3 is variable and is determined by the Timer 1 overflow rate or the baud rate generator (described in Section 8.20.5 "Baud rate generator and selection"). 8.20.5 Baud rate generator and selection The P89LPC933/934/935/936 enhanced UART has an independent baud rate generator. The baud rate is determined by a baud-rate preprogrammed into the BRGR1 and BRGR0 SFRs which together form a 16-bit baud rate divisor value that works in a similar manner as Timer 1 but is much more accurate. If the baud rate generator is used, Timer 1 can be used for other timing functions. The UART can use either Timer 1 or the baud rate generator output (see Figure 14). Note that Timer T1 is further divided by 2 if the SMOD1 bit (PCON.7) is cleared. The independent baud rate generator uses CCLK. timer 1 overflow (PCLK-based) SMOD1 = 1 SBRGS = 0 /2 baud rate modes 1 and 3 SMOD1 = 0 baud rate generator (CCLK-based) SBRGS = 1 002aaa897 Fig 14. Baud rate sources for UART (Modes 1, 3) 8.20.6 Framing error Framing error is reported in the status register (SSTAT). In addition, if SMOD0 (PCON.6) is logic 1, framing errors can be made available in SCON.7 respectively. If SMOD0 is logic 0, SCON.7 is SM0. It is recommended that SM0 and SM1 (SCON.7:6) are set up when SMOD0 is logic 0. P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 39 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 8.20.7 Break detect Break detect is reported in the status register (SSTAT). A break is detected when 11 consecutive bits are sensed LOW. The break detect can be used to reset the device and force the device into ISP mode. 8.20.8 Double buffering The UART has a transmit double buffer that allows buffering of the next character to be written to SBUF while the first character is being transmitted. Double buffering allows transmission of a string of characters with only one stop bit between any two characters, as long as the next character is written between the start bit and the stop bit of the previous character. Double buffering can be disabled. If disabled (DBMOD, i.e., SSTAT.7 = 0), the UART is compatible with the conventional 80C51 UART. If enabled, the UART allows writing to SnBUF while the previous data is being shifted out. Double buffering is only allowed in Modes 1, 2 and 3. When operated in Mode 0, double buffering must be disabled (DBMOD = 0). 8.20.9 Transmit interrupts with double buffering enabled (modes 1, 2 and 3) Unlike the conventional UART, in double buffering mode, the Tx interrupt is generated when the double buffer is ready to receive new data. 8.20.10 The 9th bit (bit 8) in double buffering (modes 1, 2 and 3) If double buffering is disabled TB8 can be written before or after SBUF is written, as long as TB8 is updated some time before that bit is shifted out. TB8 must not be changed until the bit is shifted out, as indicated by the Tx interrupt. If double buffering is enabled, TB8 must be updated before SBUF is written, as TB8 will be double-buffered together with SBUF data. P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 40 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 8.21 I2C-bus serial interface The I2C-bus uses two wires (SDA and SCL) to transfer information between devices connected to the bus, and it has the following features: * Bidirectional data transfer between masters and slaves * Multi master bus (no central master) * Arbitration between simultaneously transmitting masters without corruption of serial data on the bus * Serial clock synchronization allows devices with different bit rates to communicate via one serial bus * Serial clock synchronization can be used as a handshake mechanism to suspend and resume serial transfer * The I2C-bus may be used for test and diagnostic purposes. A typical I2C-bus configuration is shown in Figure 15. The P89LPC933/934/935/936 device provides a byte-oriented I2C-bus interface that supports data transfers up to 400 kHz. RP RP SDA I2C-bus SCL P1.3/SDA P1.2/SCL P89LPC935 OTHER DEVICE WITH I2C-BUS INTERFACE OTHER DEVICE WITH I2C-BUS INTERFACE 002aab082 Fig 15. I2C-bus configuration P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 41 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 8 I2ADR ADDRESS REGISTER P1.3 COMPARATOR INPUT FILTER P1.3/SDA SHIFT REGISTER OUTPUT STAGE ACK I2DAT BIT COUNTER / ARBITRATION AND SYNC LOGIC INPUT FILTER P1.2/SCL SERIAL CLOCK GENERATOR OUTPUT STAGE CCLK TIMING AND CONTROL LOGIC interrupt INTERNAL BUS 8 timer 1 overflow P1.2 I2CON I2SCLH I2SCLL CONTROL REGISTERS AND SCL DUTY CYCLE REGISTERS 8 status bus I2STAT STATUS DECODER STATUS REGISTER 8 002aaa899 Fig 16. I2C-bus serial interface block diagram P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 42 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 8.22 SPI The P89LPC933/934/935/936 provides another high-speed serial communication interface--the SPI interface. SPI is a full-duplex, high-speed, synchronous communication bus with two operation modes: Master mode and Slave mode. Up to 3 Mbit/s can be supported in Master mode or up to 2 Mbit/s in Slave mode. It has a Transfer Completion Flag and Write Collision Flag Protection. S M CPU clock 8-BIT SHIFT REGISTER clock S M MSTR SPICLK P2.5 SS P2.4 SPR0 SPR1 CPOL CPHA MSTR SSIG WCOL DORD MSTR SPEN SPI CONTROL SPEN SPR1 SPR0 CLOCK LOGIC MOSI P2.2 SPEN SPI clock (master) SELECT SPIF PIN CONTROL LOGIC READ DATA BUFFER DIVIDER BY 4, 16, 64, 128 MISO P2.3 M S SPI CONTROL REGISTER SPI STATUS REGISTER SPI interrupt request internal data bus 002aaa900 Fig 17. SPI block diagram The SPI interface has four pins: SPICLK, MOSI, MISO and SS: * SPICLK, MOSI and MISO are typically tied together between two or more SPI devices. Data flows from master to slave on MOSI (Master Out Slave In) pin and flows from slave to master on MISO (Master In Slave Out) pin. The SPICLK signal is output in the master mode and is input in the slave mode. If the SPI system is disabled, i.e., SPEN (SPCTL.6) = 0 (reset value), these pins are configured for port functions. * SS is the optional slave select pin. In a typical configuration, an SPI master asserts one of its port pins to select one SPI device as the current slave. An SPI slave device uses its SS pin to determine whether it is selected. Typical connections are shown in Figure 18 through Figure 20. P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 43 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 8.22.1 Typical SPI configurations master 8-BIT SHIFT REGISTER slave MISO MISO MOSI MOSI SPICLK SPI CLOCK GENERATOR PORT 8-BIT SHIFT REGISTER SPICLK SS 002aaa901 Fig 18. SPI single master single slave configuration master 8-BIT SHIFT REGISTER slave MISO MISO MOSI MOSI SPICLK SPI CLOCK GENERATOR SS 8-BIT SHIFT REGISTER SPICLK SS SPI CLOCK GENERATOR 002aaa902 Fig 19. SPI dual device configuration, where either can be a master or a slave P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 44 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core master 8-BIT SHIFT REGISTER slave MISO MISO MOSI MOSI SPICLK SPI CLOCK GENERATOR port 8-BIT SHIFT REGISTER SPICLK SS slave MISO MOSI 8-BIT SHIFT REGISTER SPICLK port SS 002aaa903 Fig 20. SPI single master multiple slaves configuration P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 45 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 8.23 Analog comparators Two analog comparators are provided on the P89LPC933/934/935/936. Input and output options allow use of the comparators in a number of different configurations. Comparator operation is such that the output is a logic 1 (which may be read in a register and/or routed to a pin) when the positive input (one of two selectable pins) is greater than the negative input (selectable from a pin or an internal reference voltage). Otherwise the output is a zero. Each comparator may be configured to cause an interrupt when the output value changes. The overall connections to both comparators are shown in Figure 21. The comparators function to VDD = 2.4 V. When each comparator is first enabled, the comparator output and interrupt flag are not guaranteed to be stable for 10 microseconds. The corresponding comparator interrupt should not be enabled during that time, and the comparator interrupt flag must be cleared before the interrupt is enabled in order to prevent an immediate interrupt service. When a comparator is disabled the comparator's output, COn, goes HIGH. If the comparator output was LOW and then is disabled, the resulting transition of the comparator output from a LOW to HIGH state will set the comparator flag, CMFn. This will cause an interrupt if the comparator interrupt is enabled. The user should therefore disable the comparator interrupt prior to disabling the comparator. Additionally, the user should clear the comparator flag, CMFn, after disabling the comparator. CP1 OE1 comparator 1 (P0.4) CIN1A (P0.3) CIN1B CO1 CMP1 (P0.6) (P0.5) CMPREF change detect Vref(bg) CMF1 CN1 interrupt change detect EC CP2 CMF2 comparator 2 (P0.2) CIN2A (P0.1) CIN2B CMP2 (P0.0) CO2 OE2 CN2 002aaa904 Fig 21. Comparator input and output connections 8.23.1 Internal reference voltage An internal reference voltage generator may supply a default reference when a single comparator input pin is used. The value of the internal reference voltage, referred to as Vref(bg), is 1.23 V 10 %. P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 46 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 8.23.2 Comparator interrupt Each comparator has an interrupt flag contained in its configuration register. This flag is set whenever the comparator output changes state. The flag may be polled by software or may be used to generate an interrupt. The two comparators use one common interrupt vector. If both comparators enable interrupts, after entering the interrupt service routine, the user needs to read the flags to determine which comparator caused the interrupt. 8.23.3 Comparators and power reduction modes Either or both comparators may remain enabled when Power-down or Idle mode is activated, but both comparators are disabled automatically in Total Power-down mode. If a comparator interrupt is enabled (except in Total Power-down mode), a change of the comparator output state will generate an interrupt and wake-up the processor. If the comparator output to a pin is enabled, the pin should be configured in the push-pull mode in order to obtain fast switching times while in Power-down mode. The reason is that with the oscillator stopped, the temporary strong pull-up that normally occurs during switching on a quasi-bidirectional port pin does not take place. Comparators consume power in Power-down and Idle modes, as well as in the normal operating mode. This fact should be taken into account when system power consumption is an issue. To minimize power consumption, the user can disable the comparators via PCONA.5, or put the device in Total Power-down mode. 8.24 Keypad interrupt The Keypad Interrupt (KBI) function is intended primarily to allow a single interrupt to be generated when Port 0 is equal to or not equal to a certain pattern. This function can be used for bus address recognition or keypad recognition. The user can configure the port via SFRs for different tasks. The Keypad Interrupt Mask register (KBMASK) is used to define which input pins connected to Port 0 can trigger the interrupt. The Keypad Pattern register (KBPATN) is used to define a pattern that is compared to the value of Port 0. The Keypad Interrupt Flag (KBIF) in the Keypad Interrupt Control register (KBCON) is set when the condition is matched while the Keypad Interrupt function is active. An interrupt will be generated if enabled. The PATN_SEL bit in the Keypad Interrupt Control register (KBCON) is used to define equal or not-equal for the comparison. In order to use the Keypad Interrupt as an original KBI function like in 87LPC76x series, the user needs to set KBPATN = 0FFH and PATN_SEL = 1 (not equal), then any key connected to Port 0 which is enabled by the KBMASK register will cause the hardware to set KBIF and generate an interrupt if it has been enabled. The interrupt may be used to wake-up the CPU from Idle or Power-down modes. This feature is particularly useful in handheld, battery-powered systems that need to carefully manage power consumption yet also need to be convenient to use. In order to set the flag and cause an interrupt, the pattern on Port 0 must be held longer than six CCLKs. P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 47 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 8.25 Watchdog timer The watchdog timer causes a system reset when it underflows as a result of a failure to feed the timer prior to the timer reaching its terminal count. It consists of a programmable 12-bit prescaler, and an 8-bit down counter. The down counter is decremented by a tap taken from the prescaler. The clock source for the prescaler is either the PCLK or the nominal 400 kHz watchdog oscillator. The watchdog timer can only be reset by a power-on reset. When the watchdog feature is disabled, it can be used as an interval timer and may generate an interrupt. Figure 22 shows the watchdog timer in Watchdog mode. Feeding the watchdog requires a two-byte sequence. If PCLK is selected as the watchdog clock and the CPU is powered-down, the watchdog is disabled. The watchdog timer has a time-out period that ranges from a few s to a few seconds. Please refer to the P89LPC933/934/935/936 User manual for more details. WDL (C1H) MOV WFEED1, #0A5H MOV WFEED2, #05AH watchdog oscillator PCLK /32 8-BIT DOWN COUNTER PRESCALER reset(1) SHADOW REGISTER WDCON (A7H) PRE2 PRE1 PRE0 - - WDRUN WDTOF WDCLK 002aaa905 (1) Watchdog reset can also be caused by an invalid feed sequence, or by writing to WDCON not immediately followed by a feed sequence. Fig 22. Watchdog timer in Watchdog mode (WDTE = 1) 8.26 Additional features 8.26.1 Software reset The SRST bit in AUXR1 gives software the opportunity to reset the processor completely, as if an external reset or watchdog reset had occurred. Care should be taken when writing to AUXR1 to avoid accidental software resets. 8.26.2 Dual data pointers The dual Data Pointers (DPTR) provides two different Data Pointers to specify the address used with certain instructions. The DPS bit in the AUXR1 register selects one of the two Data Pointers. Bit 2 of AUXR1 is permanently wired as a logic 0 so that the DPS bit may be toggled (thereby switching Data Pointers) simply by incrementing the AUXR1 register, without the possibility of inadvertently altering other bits in the register. P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 48 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 8.27 Data EEPROM (P89LPC935/936) The P89LPC935/936 has 512 bytes of on-chip Data EEPROM. The Data EEPROM is SFR based, byte readable, byte writable, and erasable (via row fill and sector fill). The user can read, write and fill the memory via SFRs and one interrupt. This Data EEPROM provides 100,000 minimum erase/program cycles for each byte. * Byte mode: In this mode, data can be read and written one byte at a time. * Row fill: In this mode, the addressed row (64 bytes) is filled with a single value. The entire row can be erased by writing 00H. * Sector fill: In this mode, all 512 bytes are filled with a single value. The entire sector can be erased by writing 00H. After the operation finishes, the hardware will set the EEIF bit, which if enabled will generate an interrupt. The flag is cleared by software. 8.28 Flash program memory 8.28.1 General description The P89LPC933/934/935/936 flash memory provides in-circuit electrical erasure and programming. The flash can be erased, read, and written as bytes. The Sector and Page Erase functions can erase any flash sector (1 kB or 2 kB depending on the device) or page (64 bytes). The Chip Erase operation will erase the entire program memory. ICP using standard commercial programmers is available. In addition, IAP and byte-erase allows code memory to be used for non-volatile data storage. On-chip erase and write timing generation contribute to a user-friendly programming interface. The P89LPC933/934/935/936 flash reliably stores memory contents even after 100,000 erase and program cycles. The cell is designed to optimize the erase and programming mechanisms. The P89LPC933/934/935/936 uses VDD as the supply voltage to perform the Program/Erase algorithms. 8.28.2 Features * * * * * Programming and erase over the full operating voltage range. Byte erase allows code memory to be used for data storage. Read/Programming/Erase using ISP/IAP/ICP. Internal fixed boot ROM, containing low-level IAP routines available to user code. Default loader providing ISP via the serial port, located in upper end of user program memory. * Boot vector allows user-provided flash loader code to reside anywhere in the flash memory space, providing flexibility to the user. * * * * * P89LPC933_934_935_936 Product data sheet Any flash program/erase operation in 2 ms. Programming with industry-standard commercial programmers. Programmable security for the code in the flash for each sector. 100,000 typical erase/program cycles for each byte. 10 year minimum data retention. All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 49 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 8.28.3 Flash organization The program memory consists of eight 2 kB sectors on the P89LPC936 device, eight 1 kB sectors on the P89LPC934/935 devices, and four 1 kB sectors on the P89LPC933 device. Each sector can be further divided into 64-byte pages. In addition to sector erase, page erase, and byte erase, a 64-byte page register is included which allows from 1 to 64 bytes of a given page to be programmed at the same time, substantially reducing overall programming time. 8.28.4 Using flash as data storage The flash code memory array of this device supports individual byte erasing and programming. Any byte in the code memory array may be read using the MOVC instruction, provided that the sector containing the byte has not been secured (a MOVC instruction is not allowed to read code memory contents of a secured sector). Thus any byte in a non-secured sector may be used for non-volatile data storage. 8.28.5 Flash programming and erasing Four different methods of erasing or programming of the flash are available. The flash may be programmed or erased in the end-user application (IAP) under control of the application's firmware. Another option is to use the ICP mechanism. This ICP system provides for programming through a serial clock - serial data interface. As shipped from the factory, the upper 512 bytes of user code space contains a serial ISP routine allowing the device to be programmed in circuit through the serial port. The flash may also be programmed or erased using a commercially available EPROM programmer which supports this device. This device does not provide for direct verification of code memory contents. Instead, this device provides a 32-bit CRC result on either a sector or the entire user code space. 8.28.6 In-circuit programming ICP is performed without removing the microcontroller from the system. The ICP facility consists of internal hardware resources to facilitate remote programming of the P89LPC933/934/935/936 through a two-wire serial interface. The Philips ICP facility has made ICP in an embedded application--using commercially available programmers--possible with a minimum of additional expense in components and circuit board area. The ICP function uses five pins. Only a small connector needs to be available to interface your application to a commercial programmer in order to use this feature. Additional details may be found in the P89LPC933/934/935/936 User manual. 8.28.7 In-application programming IAP is performed in the application under the control of the microcontroller's firmware. The IAP facility consists of internal hardware resources to facilitate programming and erasing. The Philips IAP has made IAP in an embedded application possible without additional components. Two methods are available to accomplish IAP. A set of predefined IAP functions are provided in a boot ROM and can be called through a common interface, PGM_MTP. Several IAP calls are available for use by an application program to permit selective erasing and programming of flash sectors, pages, security bits, configuration bytes, and device ID. These functions are selected by setting up the microcontroller's registers before making a call to PGM_MTP at FF03H. The boot ROM occupies the program memory space at the top of the address space from FF00H to FFEFH, thereby not conflicting with the user program memory space. P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 50 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core In addition, IAP operations can be accomplished through the use of four SFRs consisting of a control/status register, a data register, and two address registers. Additional details may be found in the P89LPC933/934/935/936 User manual. 8.28.8 ISP ISP is performed without removing the microcontroller from the system. The ISP facility consists of a series of internal hardware resources coupled with internal firmware to facilitate remote programming of the P89LPC933/934/935/936 through the serial port. This firmware is provided by Philips and embedded within each P89LPC933/934/935/936 device. The Philips ISP facility has made ISP in an embedded application possible with a minimum of additional expense in components and circuit board area. The ISP function uses five pins (VDD, VSS, TXD, RXD, and RST). Only a small connector needs to be available to interface your application to an external circuit in order to use this feature. 8.28.9 Power-on reset code execution The P89LPC933/934/935/936 contains two special flash elements: the boot vector and the boot status bit. Following reset, the P89LPC933/934/935/936 examines the contents of the boot status bit. If the boot status bit is set to zero, power-up execution starts at location 0000H, which is the normal start address of the user's application code. When the boot status bit is set to a value other than zero, the contents of the boot vector are used as the high byte of the execution address and the low byte is set to 00H. Table 9 shows the factory default boot vector settings for these devices. Remark: These settings are different than the original P89LPC932. Tools designed to support the P89LPC933/934/935/936 should be used to program this device, such as Flash Magic version 1.98, or later. A factory-provided boot loader is preprogrammed into the address space indicated and uses the indicated boot loader entry point to perform ISP functions. This code can be erased by the user. Remark: Users who wish to use this loader should take precautions to avoid erasing the sector that contains this boot loader. Instead, the page erase function can be used to erase the pages located in this sector which are not used by the boot loader. A custom boot loader can be written with the boot vector set to the custom boot loader, if desired. Table 9. P89LPC933_934_935_936 Product data sheet Default boot vector values and ISP entry points Device Default boot vector Default boot loader entry point Default boot loader Boot sector code range range P89LPC933 0FH 0F00H 0E00H to 0FFFH 0C00H to 0FFFH P89LPC934 1FH 1F00H 1E00H to 1FFFH 1C00H to 1FFFH P89LPC935 1FH 1F00H 1E00H to 1FFFH 1C00H to 1FFFH P89LPC936 3FH 3F00H 3E00H to 3FFFH 3C00H to 3FFFH All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 51 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 8.28.10 Hardware activation of the boot loader The boot loader can also be executed by forcing the device into ISP mode during a power-on sequence (see the P89LPC933/934/935/936 User manual for specific information). This has the same effect as having a non-zero status byte. This allows an application to be built that will normally execute user code but can be manually forced into ISP operation. If the factory default setting for the boot vector is changed, it will no longer point to the factory preprogrammed ISP boot loader code. After programming the flash, the status byte should be programmed to zero in order to allow execution of the user's application code beginning at address 0000H. 8.29 User configuration bytes Some user-configurable features of the P89LPC933/934/935/936 must be defined at power-up and therefore cannot be set by the program after start of execution. These features are configured through the use of the flash byte UCFG1. Please see the P89LPC933/934/935/936 User manual for additional details. 8.30 User sector security bytes There are eight User Sector Security Bytes on the P89LPC933/934/935/936 device. Each byte corresponds to one sector. Please see the P89LPC933/934/935/936 User manual for additional details. 9. A/D converter 9.1 General description The P89LPC935/936 have two 8-bit, 4-channel multiplexed successive approximation analog-to-digital converter modules sharing common control logic. The P89LPC933/934 have a single 8-bit, 4-channel multiplexed analog-to-digital converter and an additional DAC module. A block diagram of the A/D converter is shown in Figure 23. Each A/D consists of a 4-input multiplexer which feeds a sample-and-hold circuit providing an input signal to one of two comparator inputs. The control logic in combination with the SAR drives a digital-to-analog converter which provides the other input to the comparator. The output of the comparator is fed to the SAR. 9.2 Features and benefits Two (P89LPC935/936) 8-bit, 4-channel multiplexed input, successive approximation A/D converters with common control logic (one A/D on the P89LPC933/934). Four result registers for each A/D. Six operating modes: Fixed channel, single conversion mode. Fixed channel, continuous conversion mode. Auto scan, single conversion mode. Auto scan, continuous conversion mode. Dual channel, continuous conversion mode. Single step mode. Four conversion start modes: Timer triggered start. P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 52 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core Start immediately. Edge triggered. Dual start immediately (P89LPC935/936). 8-bit conversion time of 3.9 s at an A/D clock of 3.3 MHz. Interrupt or polled operation. Boundary limits interrupt. DAC output to a port pin with high output impedance. Clock divider. Power-down mode. 9.3 Block diagram comp + INPUT MUX SAR - 8 DAC1 CONTROL LOGIC comp + INPUT MUX SAR - 8 DAC0 CCLK 002aab080 Fig 23. ADC block diagram 9.4 A/D operating modes 9.4.1 Fixed channel, single conversion mode A single input channel can be selected for conversion. A single conversion will be performed and the result placed in the result register which corresponds to the selected input channel. An interrupt, if enabled, will be generated after the conversion completes. P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 53 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 9.4.2 Fixed channel, continuous conversion mode A single input channel can be selected for continuous conversion. The results of the conversions will be sequentially placed in the four result registers. An interrupt, if enabled, will be generated after every four conversions. Additional conversion results will again cycle through the four result registers, overwriting the previous results. Continuous conversions continue until terminated by the user. 9.4.3 Auto scan, single conversion mode Any combination of the four input channels can be selected for conversion. A single conversion of each selected input will be performed and the result placed in the result register which corresponds to the selected input channel. An interrupt, if enabled, will be generated after all selected channels have been converted. If only a single channel is selected this is equivalent to single channel, single conversion mode. 9.4.4 Auto scan, continuous conversion mode Any combination of the four input channels can be selected for conversion. A conversion of each selected input will be performed and the result placed in the result register which corresponds to the selected input channel. An interrupt, if enabled, will be generated after all selected channels have been converted. The process will repeat starting with the first selected channel. Additional conversion results will again cycle through the four result registers, overwriting the previous results. Continuous conversions continue until terminated by the user. 9.4.5 Dual channel, continuous conversion mode This is a variation of the auto scan continuous conversion mode where conversion occurs on two user-selectable inputs. The result of the conversion of the first channel is placed in result register, ADxDAT0. The result of the conversion of the second channel is placed in result register, ADxDAT1. The first channel is again converted and its result stored in ADxDAT2. The second channel is again converted and its result placed in ADxDAT3. An interrupt is generated, if enabled, after every set of four conversions (two conversions per channel). 9.4.6 Single step mode This special mode allows `single-stepping' in an auto scan conversion mode. Any combination of the four input channels can be selected for conversion. After each channel is converted, an interrupt is generated, if enabled, and the A/D waits for the next start condition. May be used with any of the start modes. 9.5 Conversion start modes 9.5.1 Timer triggered start An A/D conversion is started by the overflow of Timer 0. Once a conversion has started, additional Timer 0 triggers are ignored until the conversion has completed. The Timer triggered start mode is available in all A/D operating modes. 9.5.2 Start immediately Programming this mode immediately starts a conversion. This start mode is available in all A/D operating modes. P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 54 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 9.5.3 Edge triggered An A/D conversion is started by rising or falling edge of P1.4. Once a conversion has started, additional edge triggers are ignored until the conversion has completed. The edge triggered start mode is available in all A/D operating modes. 9.5.4 Dual start immediately (P89LPC935/936) Programming this mode starts a synchronized conversion of both A/D converters. This start mode is available in all A/D operating modes. Both A/D converters must be in the same operating mode. In the continuous conversion modes, both A/D converters must select an identical number of channels. Any trigger of either A/D will start a simultaneous conversion of both A/Ds. 9.6 Boundary limits interrupt Each of the A/D converters has both a high and low boundary limit register. After the four MSBs have been converted, these four bits are compared with the four MSBs of the boundary high and low registers. If the four MSBs of the conversion are outside the limit an interrupt will be generated, if enabled. If the conversion result is within the limits, the boundary limits will again be compared after all 8 bits have been converted. An interrupt will be generated, if enabled, if the result is outside the boundary limits. The boundary limit may be disabled by clearing the boundary limit interrupt enable. 9.7 DAC output to a port pin with high output impedance Each A/D converter's DAC block can be output to a port pin. In this mode, the ADxDAT3 register is used to hold the value fed to the DAC. After a value has been written to the DAC (written to ADxDAT3), the DAC output will appear on the channel 3 pin. 9.8 Clock divider The A/D converter requires that its internal clock source be in the range of 500 kHz to 3.3 MHz to maintain accuracy. A programmable clock divider that divides the clock from 1 to 8 is provided for this purpose. 9.9 Power-down and Idle mode In Idle mode the A/C converter, if enabled, will continue to function and can cause the device to exit Idle mode when the conversion is completed if the A/D interrupt is enabled. In Power-down mode or Total Power-down mode, the A/D does not function. If the A/D is enabled, it will consume power. Power can be reduced by disabling the A/D. P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 55 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 10. Limiting values Table 10. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134).[1] Symbol Parameter Tamb(bias) Min Max Unit bias ambient temperature -55 +125 C Tstg storage temperature -65 +150 C IOH(I/O) HIGH-level output current per input/output pin - 20 mA IOL(I/O) LOW-level output current per input/output pin - 20 mA II/Otot(max) maximum total input/output current - 100 mA Vxtal crystal voltage on XTAL1, XTAL2 pin to VSS - VDD + 0.5 V Vn voltage on any other pin except XTAL1, XTAL2 to VSS -0.5 +5.5 V Ptot(pack) total power dissipation (per package) based on package heat transfer, not device power consumption - 1.5 W [1] Conditions The following applies to Table 10: a) This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive static charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated maximum. b) Parameters are valid over ambient temperature range unless otherwise specified. All voltages are with respect to VSS unless otherwise noted. P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 56 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 11. Static characteristics Table 11. Static characteristics VDD = 2.4 V to 3.6 V unless otherwise specified. Tamb = -40 C to +85 C for industrial, -40 C to +125 C for extended, unless otherwise specified. Symbol IDD(oper) IDD(idle) Parameter Min Typ[1] Max Unit VDD = 3.6 V; fosc = 12 MHz [2] - 11 18 mA VDD = 3.6 V; fosc = 18 MHz [2] - 14 23 mA VDD = 3.6 V; fosc = 12 MHz [2] - 3.25 5 mA VDD = 3.6 V; fosc = 18 MHz [2] - 5 7 mA - 55 80 A Conditions operating supply current Idle mode supply current IDD(pd) Power-down mode supply current VDD = 3.6 V; voltage comparators powered down [2] IDD(tpd) total Power-down mode supply current all devices except P89LPC933HDH; VDD = 3.6 V [3] - 1 5 A P89LPC933HDH only; VDD = 3.6 V [3] - - 25 A (dV/dt)r rise rate of VDD - - 2 mV/s (dV/dt)f fall rate of VDD - - 50 mV/s VPOR power-on reset voltage - - 0.5 V VDDR data retention supply voltage 1.5 - - V Vth(HL) HIGH-LOW threshold voltage except SCL, SDA 0.22VDD 0.4VDD - V VIL LOW-level input voltage SCL, SDA only -0.5 - 0.3VDD V Vth(LH) LOW-HIGH threshold voltage except SCL, SDA - 0.6VDD 0.7VDD V VIH HIGH-level input voltage SCL, SDA only 0.7VDD - 5.5 V Vhys hysteresis voltage port 1 VOL LOW-level output voltage IOL = 20 mA; VDD = 2.4 V to 3.6 V all ports, all modes except high-Z VOH HIGH-level output voltage - 0.2VDD - V - 0.6 1.0 V IOL = 3.2 mA; VDD = 2.4 V to 3.6 V all ports, all modes except high-Z - 0.2 0.3 V IOH = -20 A; VDD = 2.4 V to 3.6 V; all ports, quasi-bidirectional mode VDD - 0.3 VDD - 0.2 - V IOH = -3.2 mA; VDD = 2.4 V to 3.6 V; all ports, push-pull mode VDD - 0.7 VDD - 0.4 - V IOH = -10 mA; VDD = 3.6 V; all ports, push-pull mode - 3.2 - V -0.5 - +4.0 V [5] -0.5 - +5.5 V [6] - - 15 pF Vxtal crystal voltage on XTAL1, XTAL2 pins; with respect to VSS Vn voltage on any other pin except XTAL1, XTAL2, VDD; with respect to VSS Ciss input capacitance P89LPC933_934_935_936 Product data sheet [4] All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 57 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core Table 11. Static characteristics ...continued VDD = 2.4 V to 3.6 V unless otherwise specified. Tamb = -40 C to +85 C for industrial, -40 C to +125 C for extended, unless otherwise specified. Symbol IIL Parameter Min Typ[1] Max Unit VI = 0.4 V [7] - - -80 A - - 10 A -30 - -450 A 10 - 30 k 2.40 - 2.70 V Conditions LOW-level input current ILI input leakage current VI = VIL, VIH or Vth(HL) [8] ITHL HIGH-LOW transition current all ports; VI = 1.5 V at VDD = 3.6 V [9] RRST_N(int) internal pull-up resistance on pin RST Vbo brownout trip voltage Vref(bg) band gap reference voltage 1.11 1.23 1.34 V TCbg band gap temperature coefficient - 10 20 ppm/ C 2.4 V < VDD < 3.6 V; with BOV = 1, BOPD = 0 [1] Typical ratings are not guaranteed. The values listed are at room temperature, 3 V. [2] The IDD(oper), IDD(idle), and IDD(pd) specifications are measured using an external clock with the following functions disabled: comparators, real-time clock, and watchdog timer. [3] The IDD(tpd) specification is measured using an external clock with the following functions disabled: comparators, real-time clock, brownout detect, and watchdog timer. [4] See Section 10 "Limiting values" for steady state (non-transient) limits on IOL or IOH. If IOL/IOH exceeds the test condition, VOL/VOH may exceed the related specification. [5] This specification can be applied to pins which have A/D input or analog comparator input functions when the pin is not being used for those analog functions. When the pin is being used as an analog input pin, the maximum voltage on the pin must be limited to 4.0 V with respect to VSS. [6] Pin capacitance is characterized but not tested. [7] Measured with port in quasi-bidirectional mode. [8] Measured with port in high-impedance mode. [9] Port pins source a transition current when used in quasi-bidirectional mode and externally driven from logic 1 to logic 0. This current is highest when VI is approximately 2 V. P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 58 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 11.1 IOH as a function of VOH 002aab098 40 002aab099 25 IOH IOH 20 30 15 20 10 10 5 0 0 0 1 2 3 4 0 VOH 1 2 3 VOH a. Tamb = 25 C; VDD = 3.6 V; push-pull mode b. Tamb = 25 C; VDD = 2.6 V; push-pull mode Fig 24. IOH as a function of VOH (typical values) P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 59 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 12. Dynamic characteristics Table 12. Dynamic characteristics (12 MHz) VDD = 2.4 V to 3.6 V unless otherwise specified. Tamb = -40 C to +85 C for industrial, -40 C to +125 C for extended, unless otherwise specified.[1][2] Symbol Parameter Conditions fosc(RC) internal RC oscillator frequency fosc(WD) internal watchdog oscillator frequency fosc oscillator frequency Tcy(clk) clock cycle time fCLKLP low-power select clock frequency Variable clock fosc = 12 MHz Unit Min Max Min 7.189 7.557 7.189 Max 320 520 320 520 kHz 7.557 MHz 0 12 - - MHz 83 - - - ns 0 8 - - MHz P1.5/RST pin - 50 - 50 ns any pin except P1.5/RST - 15 - 15 ns see Figure 27 Glitch filter tgr tsa glitch rejection time signal acceptance time P1.5/RST pin 125 - 125 - ns any pin except P1.5/RST 50 - 50 - ns External clock tCHCX clock HIGH time see Figure 27 33 Tcy(CLK) - tCLCX 33 - ns tCLCX clock LOW time see Figure 27 33 Tcy(CLK) - tCHCX 33 - ns tCLCH clock rise time see Figure 27 - 8 - 8 ns tCHCL clock fall time see Figure 27 - 8 - 8 ns Shift register (UART mode 0) TXLXL serial port clock cycle time see Figure 25 16Tcy(CLK) - 1333 - ns tQVXH output data set-up to clock rising see Figure 25 edge time 13Tcy(CLK) - 1083 - ns tXHQX output data hold after clock rising edge time see Figure 25 - Tcy(CLK) + 20 - 103 ns tXHDX input data hold after clock rising edge time see Figure 25 - 0 - 0 ns tXHDV input data valid to clock rising edge time see Figure 25 150 - 150 - ns slave 0 CCLK 6 0 2.0 MHz master - CCLK 4 - 3.0 MHz SPI interface fSPI TSPICYC SPI operating frequency SPI cycle time slave see Figure 26, 28, 29, 30 master tSPILEAD SPI enable lead time 6 CCLK - 500 - ns 4 CCLK - 333 - ns 250 - 250 - ns see Figure 29, 30 slave P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 60 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core Table 12. Dynamic characteristics (12 MHz) ...continued VDD = 2.4 V to 3.6 V unless otherwise specified. Tamb = -40 C to +85 C for industrial, -40 C to +125 C for extended, unless otherwise specified.[1][2] Symbol tSPILAG Parameter Conditions SPI enable lag time Variable clock SPICLK HIGH time see Figure 26, 28, 29, 30 250 - ns ns CCLK - 250 - ns 2 CCLK - 165 - ns 3 CCLK - 250 - ns see Figure 26, 28, 29, 30 100 - 100 - ns see Figure 26, 28, 29, 30 100 - 100 - ns 0 120 0 120 ns 0 240 - 240 ns slave - 240 - 240 ns master - 167 - 167 ns 0 - 0 - ns - 100 - 100 ns - 2000 - 2000 ns - 100 - 100 ns - 2000 - 2000 ns SPICLK LOW time see Figure 26, 28, 29, 30 SPI data set-up time SPI data hold time SPI access time see Figure 29, 30 slave SPI disable time see Figure 29, 30 slave SPI enable to output data valid time see Figure 26, 28, 29, 30 tSPIOH SPI output data hold time see Figure 26, 28, 29, 30 tSPIR SPI rise time see Figure 26, 28, 29, 30 SPI outputs (SPICLK, MOSI, MISO) SPI inputs (SPICLK, MOSI, MISO, SS) tSPIF - - master or slave tSPIDV 250 165 master or slave tSPIDIS Max - slave tSPIA Min CCLK master tSPIDH Max 3 slave tSPIDSU Min 2 master tSPICLKL Unit see Figure 29, 30 slave tSPICLKH fosc = 12 MHz SPI fall time see Figure 26, 28, 29, 30 SPI outputs (SPICLK, MOSI, MISO) SPI inputs (SPICLK, MOSI, MISO, SS) [1] Parameters are valid over ambient temperature range unless otherwise specified. [2] Parts are tested to 2 MHz, but are guaranteed to operate down to 0 Hz. P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 61 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core Table 13. Dynamic characteristics (18 MHz) VDD = 3.0 V to 3.6 V unless otherwise specified. Tamb = -40 C to +85 C for industrial, -40 C to +125 C for extended, unless otherwise specified.[1][2] Symbol Parameter Conditions fosc(RC) internal RC oscillator frequency fosc(WD) internal watchdog oscillator frequency fosc oscillator frequency Tcy(CLK) clock cycle fCLKLP low-power select clock frequency Variable clock fosc = 18 MHz Unit Min Max Min 7.189 7.557 7.189 320 520 320 520 kHz 0 18 - - MHz 55 - - - ns 0 8 - - MHz P1.5/RST pin - 50 - 50 ns any pin except P1.5/RST - 15 - 15 ns P1.5/RST pin 125 - 125 - ns any pin except P1.5/RST 50 - 50 - ns see Figure 27 Max 7.557 MHz Glitch filter tgr tsa glitch rejection time signal acceptance time External clock tCHCX clock HIGH time see Figure 27 22 Tcy(CLK) - tCLCX 22 - ns tCLCX clock LOW time see Figure 27 22 Tcy(CLK) - tCHCX 22 - ns tCLCH clock rise time see Figure 27 - 5 - 5 ns tCHCL clock fall time see Figure 27 - 5 - 5 ns Shift register (UART mode 0) TXLXL serial port clock cycle time see Figure 25 16Tcy(CLK) - 888 - ns tQVXH output data set-up to clock rising edge time see Figure 25 13Tcy(CLK) - 722 - ns tXHQX output data hold after clock rising edge time see Figure 25 - Tcy(CLK) + 20 - 75 ns tXHDX input data hold after clock rising see Figure 25 edge time - 0 - 0 ns tXHDV input data valid to clock rising edge time 150 - 150 - ns 0 CCLK 6 0 3.0 MHz - CCLK 4 - 4.5 MHz see Figure 25 SPI interface fSPI SPI operating frequency slave master TSPICYC SPI cycle time slave see Figure 26, 28, 29, 30 SPI enable lead time SPI enable lag time Product data sheet 333 - ns CCLK - 222 - ns 250 - 250 - ns 250 - 250 - ns see Figure 29, 30 slave P89LPC933_934_935_936 - see Figure 29, 30 slave tSPILAG CCLK 4 master tSPILEAD 6 All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 62 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core Table 13. Dynamic characteristics (18 MHz) ...continued VDD = 3.0 V to 3.6 V unless otherwise specified. Tamb = -40 C to +85 C for industrial, -40 C to +125 C for extended, unless otherwise specified.[1][2] Symbol Parameter Conditions Variable clock Min tSPICLKH SPICLK HIGH time see Figure 26, 28, 29, 30 - 111 - ns CCLK - 167 - ns 2 CCLK - 111 - ns CCLK - 167 - ns see Figure 26, 28, 29, 30 100 - 100 - ns see Figure 26, 28, 29, 30 100 - 100 - ns 0 80 0 80 ns 0 160 - 160 ns slave - 160 - 160 ns master - 111 - 111 ns 0 - 0 - ns - 100 - 100 ns - 2000 - 2000 ns - 100 - 100 ns - 2000 - 2000 ns SPICLK LOW time see Figure 26, 28, 29, 30 3 slave SPI data set-up time master or slave SPI data hold time master or slave tSPIA SPI access time see Figure 29, 30 slave tSPIDIS SPI disable time see Figure 29, 30 slave tSPIDV SPI enable to output data valid time see Figure 26, 28, 29, 30 tSPIOH SPI output data hold time see Figure 26, 28, 29, 30 tSPIR SPI rise time see Figure 26, 28, 29, 30 SPI outputs (SPICLK, MOSI, MISO) SPI inputs (SPICLK, MOSI, MISO, SS) tSPIF Max CCLK master tSPIDH Min 3 slave tSPIDSU Max Unit 2 master tSPICLKL fosc = 18 MHz SPI fall time see Figure 26, 28, 29, 30 SPI outputs (SPICLK, MOSI, MISO) SPI inputs (SPICLK, MOSI, MISO, SS) [1] Parameters are valid over ambient temperature range unless otherwise specified. [2] Parts are tested to 2 MHz, but are guaranteed to operate down to 0 Hz. P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 63 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 12.1 Waveforms TXLXL clock tXHQX tQVXH output data 0 write to SBUF input data 1 2 3 4 5 6 tXHDX set TI tXHDV valid 7 valid valid valid valid valid valid valid clear RI set RI 002aaa906 Fig 25. Shift register mode timing SS TSPICYC tSPIF tSPICLKH tSPIR tSPICLKL SPICLK (CPOL = 0) (output) tSPIF tSPICLKL tSPIR tSPICLKH SPICLK (CPOL = 1) (output) tSPIDSU MISO (input) tSPIDH LSB/MSB in MSB/LSB in tSPIDV MOSI (output) tSPIOH tSPIDV tSPIR tSPIF master MSB/LSB out master LSB/MSB out 002aaa908 Fig 26. SPI master timing (CPHA = 0) tCHCL tCHCX tCLCH tCLCX Tcy(clk) 002aaa907 Fig 27. External clock timing (with an amplitude of at least Vi(RMS) = 200 mV) P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 64 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core SS TSPICYC tSPIF tSPICLKL tSPIR tSPICLKH SPICLK (CPOL = 0) (output) tSPIF tSPICLKL tSPICLKH SPICLK (CPOL = 1) (output) tSPIDSU MISO (input) tSPIDH LSB/MSB in MSB/LSB in tSPIDV MOSI (output) tSPIR tSPIOH tSPIDV tSPIF tSPIR master MSB/LSB out master LSB/MSB out 002aaa909 Fig 28. SPI master timing (CPHA = 1) SS tSPIF tSPIR TSPICYC tSPILEAD tSPIF tSPICLKH tSPICLKL tSPIR tSPILAG SPICLK (CPOL = 0) (input) tSPIF tSPICLKL tSPIR tSPICLKH SPICLK (CPOL = 1) (input) tSPIOH tSPIA tSPIOH MISO (output) slave MSB/LSB out tSPIDSU MOSI (input) tSPIOH tSPIDH tSPIDIS tSPIDV tSPIDV slave LSB/MSB out tSPIDSU tSPIDSU MSB/LSB in not defined tSPIDH LSB/MSB in 002aaa910 Fig 29. SPI slave timing (CPHA = 0) P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 65 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core SS tSPIF tSPILEAD tSPIR TSPICYC tSPIF tSPIR tSPICLKL tSPILAG tSPICLKH SPICLK (CPOL = 0) (input) tSPIF tSPIR tSPICLKL SPICLK (CPOL = 1) (input) tSPICLKH tSPIOH tSPIOH tSPIOH tSPIDV tSPIDV tSPIDV tSPIDIS tSPIA MISO (output) slave LSB/MSB out slave MSB/LSB out not defined tSPIDSU MOSI (input) tSPIDH tSPIDSU MSB/LSB in tSPIDH LSB/MSB in 002aaa911 Fig 30. SPI slave timing (CPHA = 1) 12.2 ISP entry mode Table 14. Dynamic characteristics, ISP entry mode VDD = 2.4 V to 3.6 V, unless otherwise specified. Tamb = -40 C to +85 C for industrial, -40 C to +125 C for extended, unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit tVR RST delay from VDD active time 50 - - s tRH RST HIGH time 1 - 32 s tRL RST LOW time 1 - - s VDD tVR tRH RST tRL 002aaa912 Fig 31. ISP entry timing P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 66 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 13. Other characteristics 13.1 Comparator electrical characteristics Table 15. Comparator electrical characteristics VDD = 2.4 V to 3.6 V, unless otherwise specified. Tamb = -40 C to +85 C for industrial, -40 C to +125 C for extended, unless otherwise specified. Symbol Parameter VIO input offset voltage VIC common-mode input voltage CMRR common-mode rejection ratio Conditions [1] Min Typ Max Unit - - 20 mV 0 - VDD - 0.3 V - - -50 dB tres(tot) total response time - 250 500 ns t(CE-OV) chip enable to output valid time - - 10 s ILI input leakage current - - 10 A [1] 0 < VI < VDD This parameter is characterized, but not tested in production. P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 67 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 13.2 ADC electrical characteristics Table 16. ADC electrical characteristics VDD = 2.4 V to 3.6 V, unless otherwise specified. Tamb = -40 C to +85 C for industrial, -40 C to +125 C for extended, unless otherwise specified. All limits valid for an external source impedance of less than 10 k. Symbol Parameter Min Typ Max Unit VIA analog input voltage VSS -0.2 - VDD +0.2 V Ciss input capacitance - - 15 pF ED differential linearity error - - 1 LSB EL(adj) integral non-linearity - - 1 LSB EO offset error - - 2 LSB EG gain error - - 1 % Eu(tot) total unadjusted error - - 2 LSB MCTC channel-to-channel matching - - 1 LSB ct(port) crosstalk between port inputs - - -60 dB SRin input slew rate - - 100 V/ms Tcy(ADC) ADC clock cycle time 111 - 2000 ns tADC ADC conversion time - - 13Tcy(ADC) ns P89LPC933_934_935_936 Product data sheet Conditions 0 kHz to 100 kHz A/D enabled All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 68 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 14. Package outline PLCC28: plastic leaded chip carrier; 28 leads SOT261-2 eD y eE X A 19 25 b1 ZE 18 26 bp w M 28 1 E HE pin 1 index e A A4 A1 12 4 (A 3) k 5 11 Lp v M A ZD e D detail X B HD v M B 0 5 10 mm scale DIMENSIONS (mm dimensions are derived from the original inch dimensions) A4 A1 b1 D(1) E(1) bp A3 eD eE e HD UNIT A max. min. 4.57 4.19 mm inches 0.81 0.66 HE k 10.92 10.92 12.57 12.57 1.22 11.58 11.58 1.27 9.91 9.91 12.32 12.32 1.07 11.43 11.43 0.51 0.25 3.05 0.53 0.33 0.180 0.02 0.165 0.01 0.12 0.021 0.032 0.456 0.456 0.05 0.013 0.026 0.450 0.450 0.43 0.39 0.43 0.39 Lp v w y 1.44 1.02 0.18 0.18 0.1 ZD(1) ZE(1) max. max. 2.16 2.16 45 o 0.495 0.495 0.048 0.057 0.007 0.007 0.004 0.085 0.085 0.485 0.485 0.042 0.040 Note 1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC JEITA SOT261-2 112E08 MS-018 EDR-7319 EUROPEAN PROJECTION ISSUE DATE 99-12-27 01-11-15 Fig 32. Package outline SOT261-2 (PLCC28) P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 69 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core TSSOP28: plastic thin shrink small outline package; 28 leads; body width 4.4 mm D SOT361-1 E A X c HE y v M A Z 15 28 Q A2 (A 3) A1 pin 1 index A Lp 1 L 14 detail X w M bp e 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (2) e HE L Lp Q v w y Z (1) mm 1.1 0.15 0.05 0.95 0.80 0.25 0.30 0.19 0.2 0.1 9.8 9.6 4.5 4.3 0.65 6.6 6.2 1 0.75 0.50 0.4 0.3 0.2 0.13 0.1 0.8 0.5 8 o 0 o Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT361-1 REFERENCES IEC JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-19 MO-153 Fig 33. Package outline SOT361-1 (TSSOP28) P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 70 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core HVQFN28: plastic thermal enhanced very thin quad flat package; no leads; 28 terminals; body 6 x 6 x 0.85 mm B D SOT788-1 A terminal 1 index area A A1 E c detail X C e1 e 14 y y1 C v M C A B w M C b 8 L 7 15 e e2 Eh 21 1 terminal 1 index area 28 22 X Dh 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A(1) max. A1 b c D (1) Dh E (1) Eh e e1 e2 L v w y y1 mm 1 0.05 0.00 0.35 0.25 0.2 6.1 5.9 4.25 3.95 6.1 5.9 4.25 3.95 0.65 3.9 3.9 0.75 0.50 0.1 0.05 0.05 0.1 Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC JEITA SOT788-1 --- MO-220 --- EUROPEAN PROJECTION ISSUE DATE 02-10-22 Fig 34. Package outline SOT788-1 (HVQFN28) P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 71 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 15. Abbreviations Table 17. P89LPC933_934_935_936 Product data sheet Acronym list Acronym Description A/D Analog to Digital CPU Central Processing Unit DAC Digital to Analog Converter EPROM Erasable Programmable Read-Only Memory EEPROM Electrically Erasable Programmable Read-Only Memory EMI Electro-Magnetic Interference LED Light Emitting Diode PWM Pulse Width Modulator RAM Random Access Memory RC Resistance-Capacitance RTC Real-Time Clock SAR Successive Approximation Register SFR Special Function Register SPI Serial Peripheral Interface UART Universal Asynchronous Receiver/Transmitter All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 72 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 16. Revision history Table 18. Revision history Document ID Release date Data sheet status Change notice Supersedes P89LPC933_934_ 935_936 v.8 20110112 Product data sheet - Modifications: * * * * P89LPC933_934_ 935_936 v.7 Table 10 "Limiting values": Changed Vn max to 5.5 V. Table 11 "Static characteristics": Added VPOR. Table 16 "ADC electrical characteristics": Corrected VIA max. Section 8.16 "Reset": Added sentence "When this pin functions as a reset input...." P89LPC933_934_ 935_936 v.7 20081126 Product data sheet - P89LPC933_934_ 935_936 v.6 P89LPC933_934_ 935_936 v.6 20050620 Product data sheet - P89LPC933_934_ 935_936 v.5 P89LPC933_934_ 935_936 v.5 20041103 Product data sheet - P89LPC933_934_ 935 v.4 P89LPC933_934_ 935 v.4 20040209 Objective data - P89LPC933_934_ 935 v.3 P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 73 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 17. Legal information 17.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term `short data sheet' is explained in section "Definitions". [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 17.2 Definitions Draft -- The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet -- A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification -- The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 17.3 Disclaimers Limited warranty and liability -- Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors' aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications -- Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer's sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer's applications and products planned, as well as for the planned application and use of customer's third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer's applications or products, or the application or use by customer's third party customer(s). Customer is responsible for doing all necessary testing for the customer's applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer's third party customer(s). NXP does not accept any liability in this respect. Limiting values -- Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale -- NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer's general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. Right to make changes -- NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. No offer to sell or license -- Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Suitability for use -- NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or Export control -- This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from national authorities. P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 74 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core Non-automotive qualified products -- Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors' warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors' specifications such use shall be solely at customer's own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors' standard warranty and NXP Semiconductors' product specifications. 17.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. I2C-bus -- logo is a trademark of NXP B.V. 18. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 75 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 19. Contents 1 General description . . . . . . . . . . . . . . . . . . . . . . 1 2 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 2.1 Principal features . . . . . . . . . . . . . . . . . . . . . . . 1 2.2 Additional features . . . . . . . . . . . . . . . . . . . . . . 2 3 Product comparison overview . . . . . . . . . . . . . 3 4 Ordering information . . . . . . . . . . . . . . . . . . . . . 3 4.1 Ordering options . . . . . . . . . . . . . . . . . . . . . . . . 3 5 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 4 6 Pinning information . . . . . . . . . . . . . . . . . . . . . . 5 6.1 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 6.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 7 7 Logic symbols . . . . . . . . . . . . . . . . . . . . . . . . . 11 8 Functional description . . . . . . . . . . . . . . . . . . 12 8.1 Special function registers . . . . . . . . . . . . . . . . 12 8.2 Enhanced CPU . . . . . . . . . . . . . . . . . . . . . . . . 24 8.3 Clocks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 8.3.1 Clock definitions . . . . . . . . . . . . . . . . . . . . . . . 24 8.3.2 CPU clock (OSCCLK). . . . . . . . . . . . . . . . . . . 24 8.3.3 Low speed oscillator option . . . . . . . . . . . . . . 24 8.3.4 Medium speed oscillator option . . . . . . . . . . . 24 8.3.5 High speed oscillator option . . . . . . . . . . . . . . 24 8.3.6 Clock output . . . . . . . . . . . . . . . . . . . . . . . . . . 24 8.4 On-chip RC oscillator option . . . . . . . . . . . . . . 25 8.5 Watchdog oscillator option . . . . . . . . . . . . . . . 25 8.6 External clock input option . . . . . . . . . . . . . . . 25 8.7 CCLK wake-up delay . . . . . . . . . . . . . . . . . . . 27 8.8 CCLK modification: DIVM register . . . . . . . . . 27 8.9 Low power select . . . . . . . . . . . . . . . . . . . . . . 27 8.10 Memory organization . . . . . . . . . . . . . . . . . . . 27 8.11 Data RAM arrangement . . . . . . . . . . . . . . . . . 28 8.12 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 8.12.1 External interrupt inputs . . . . . . . . . . . . . . . . . 28 8.13 I/O ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 8.13.1 Port configurations . . . . . . . . . . . . . . . . . . . . . 30 8.13.1.1 Quasi-bidirectional output configuration . . . . . 30 8.13.1.2 Open-drain output configuration . . . . . . . . . . . 30 8.13.1.3 Input-only configuration . . . . . . . . . . . . . . . . . 31 8.13.1.4 Push-pull output configuration . . . . . . . . . . . . 31 8.13.2 Port 0 analog functions . . . . . . . . . . . . . . . . . . 31 8.13.3 Additional port features. . . . . . . . . . . . . . . . . . 31 8.14 Power monitoring functions . . . . . . . . . . . . . . 31 8.14.1 Brownout detection . . . . . . . . . . . . . . . . . . . . . 32 8.14.2 Power-on detection. . . . . . . . . . . . . . . . . . . . . 32 8.15 Power reduction modes . . . . . . . . . . . . . . . . . 32 8.15.1 Idle mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 8.15.2 Power-down mode . . . . . . . . . . . . . . . . . . . . . 32 8.15.3 8.16 8.16.1 8.17 8.17.1 8.17.2 8.17.3 8.17.4 8.17.5 8.17.6 8.18 8.19 8.19.1 8.19.2 8.19.3 8.19.4 8.19.5 8.19.6 8.19.7 8.19.8 8.19.9 8.20 8.20.1 8.20.2 8.20.3 8.20.4 8.20.5 8.20.6 8.20.7 8.20.8 8.20.9 8.20.10 8.21 8.22 8.22.1 8.23 8.23.1 8.23.2 8.23.3 8.24 8.25 8.26 8.26.1 8.26.2 8.27 8.28 Total Power-down mode . . . . . . . . . . . . . . . . Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reset vector. . . . . . . . . . . . . . . . . . . . . . . . . . Timers/counters 0 and 1 . . . . . . . . . . . . . . . . Mode 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mode 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mode 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mode 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mode 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Timer overflow toggle output . . . . . . . . . . . . . RTC/system timer . . . . . . . . . . . . . . . . . . . . . CCU (P89LPC935/936) . . . . . . . . . . . . . . . . . CCU clock . . . . . . . . . . . . . . . . . . . . . . . . . . . CCUCLK prescaling. . . . . . . . . . . . . . . . . . . . Basic timer operation . . . . . . . . . . . . . . . . . . . Output compare . . . . . . . . . . . . . . . . . . . . . . . Input capture . . . . . . . . . . . . . . . . . . . . . . . . . PWM operation . . . . . . . . . . . . . . . . . . . . . . . Alternating output mode. . . . . . . . . . . . . . . . . PLL operation. . . . . . . . . . . . . . . . . . . . . . . . . CCU interrupts . . . . . . . . . . . . . . . . . . . . . . . . UART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mode 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mode 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mode 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mode 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Baud rate generator and selection. . . . . . . . . Framing error . . . . . . . . . . . . . . . . . . . . . . . . . Break detect. . . . . . . . . . . . . . . . . . . . . . . . . . Double buffering. . . . . . . . . . . . . . . . . . . . . . . Transmit interrupts with double buffering enabled (modes 1, 2 and 3) . . . . . . The 9th bit (bit 8) in double buffering (modes 1, 2 and 3) . . . . . . . . . . . . . I2C-bus serial interface. . . . . . . . . . . . . . . . . . SPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Typical SPI configurations . . . . . . . . . . . . . . . Analog comparators . . . . . . . . . . . . . . . . . . . . Internal reference voltage . . . . . . . . . . . . . . . Comparator interrupt . . . . . . . . . . . . . . . . . . . Comparators and power reduction modes . . . Keypad interrupt. . . . . . . . . . . . . . . . . . . . . . . Watchdog timer . . . . . . . . . . . . . . . . . . . . . . . Additional features . . . . . . . . . . . . . . . . . . . . . Software reset . . . . . . . . . . . . . . . . . . . . . . . . Dual data pointers . . . . . . . . . . . . . . . . . . . . . Data EEPROM (P89LPC935/936) . . . . . . . . . Flash program memory . . . . . . . . . . . . . . . . . 33 33 33 34 34 34 34 34 34 34 34 35 35 35 35 35 35 36 37 37 38 38 38 39 39 39 39 39 40 40 40 40 41 43 44 46 46 47 47 47 48 48 48 48 49 49 continued >> P89LPC933_934_935_936 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 8 -- 12 January 2011 (c) NXP B.V. 2011. All rights reserved. 76 of 77 P89LPC933/934/935/936 NXP Semiconductors 8-bit microcontroller with accelerated two-clock 80C51 core 8.28.1 General description . . . . . . . . . . . . . . . . . . . . 8.28.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.28.3 Flash organization . . . . . . . . . . . . . . . . . . . . . 8.28.4 Using flash as data storage . . . . . . . . . . . . . . 8.28.5 Flash programming and erasing . . . . . . . . . . . 8.28.6 In-circuit programming . . . . . . . . . . . . . . . . . . 8.28.7 In-application programming . . . . . . . . . . . . . . 8.28.8 ISP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.28.9 Power-on reset code execution . . . . . . . . . . . 8.28.10 Hardware activation of the boot loader . . . . . . 8.29 User configuration bytes . . . . . . . . . . . . . . . . . 8.30 User sector security bytes . . . . . . . . . . . . . . . 9 A/D converter . . . . . . . . . . . . . . . . . . . . . . . . . . 9.1 General description . . . . . . . . . . . . . . . . . . . . 9.2 Features and benefits . . . . . . . . . . . . . . . . . . . 9.3 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . 9.4 A/D operating modes . . . . . . . . . . . . . . . . . . . 9.4.1 Fixed channel, single conversion mode . . . . . 9.4.2 Fixed channel, continuous conversion mode . 9.4.3 Auto scan, single conversion mode . . . . . . . . 9.4.4 Auto scan, continuous conversion mode . . . . 9.4.5 Dual channel, continuous conversion mode . . 9.4.6 Single step mode . . . . . . . . . . . . . . . . . . . . . . 9.5 Conversion start modes . . . . . . . . . . . . . . . . . 9.5.1 Timer triggered start . . . . . . . . . . . . . . . . . . . . 9.5.2 Start immediately . . . . . . . . . . . . . . . . . . . . . . 9.5.3 Edge triggered . . . . . . . . . . . . . . . . . . . . . . . . 9.5.4 Dual start immediately (P89LPC935/936) . . . 9.6 Boundary limits interrupt . . . . . . . . . . . . . . . . . 9.7 DAC output to a port pin with high output impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.8 Clock divider . . . . . . . . . . . . . . . . . . . . . . . . . . 9.9 Power-down and Idle mode . . . . . . . . . . . . . . 10 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 11 Static characteristics. . . . . . . . . . . . . . . . . . . . 11.1 IOH as a function of VOH . . . . . . . . . . . . . . . . . 12 Dynamic characteristics . . . . . . . . . . . . . . . . . 12.1 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.2 ISP entry mode . . . . . . . . . . . . . . . . . . . . . . . . 13 Other characteristics . . . . . . . . . . . . . . . . . . . . 13.1 Comparator electrical characteristics . . . . . . . 13.2 ADC electrical characteristics . . . . . . . . . . . . . 14 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 15 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 17 Legal information. . . . . . . . . . . . . . . . . . . . . . . 17.1 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 17.2 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.3 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 49 50 50 50 50 50 51 51 52 52 52 52 52 52 53 53 53 54 54 54 54 54 54 54 54 55 55 55 17.4 18 19 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Contact information . . . . . . . . . . . . . . . . . . . . 75 Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 55 55 55 56 57 59 60 64 66 67 67 68 69 72 73 74 74 74 74 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section `Legal information'. (c) NXP B.V. 2011. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 12 January 2011 Document identifier: P89LPC933_934_935_936