BAJ5CC0FP-E2 - Rohm Semiconductor

○Product structure : Silicon monolithic integrated circuit ○This product is not designed protection against radioactive rays.

1/20 TSZ02201-0R6R0A600130-1-2

TSZ22111･14･001 26.Jun.2012 Rev.001

www.rohm.com

Datashee

2A/1A Fixed Output LDO Regulators

BAxxDD0T Series BAxxCC0T Series BAxxCC0FP Series

2A/1A Fixed Output LDO Regulators

With Shutdown Swicth

BAxxDD0WT Series BAxxDD0HFP Series BAxxCC0WT Series BAxxCC0WFP Series

●General Description

Standard Fixed Output LDO Regulators are low-saturation regulators, available for output s up to 2A / 1A. ROHM has a

wide output voltage range and package lineup with and without shutdown switches. This IC has a built-in over-current

protection circuit that prevents the destruction of the IC due to output short circuits, a thermal shut-down circuit that protects

the IC from damage due to overloading and an over-voltage protection circuit that protects the IC from surges generated in

the power supply line of the IC.

●Features

 ±1% highly accurate output voltage (BAxxDD0xx)

 Low saturation with PNP output

 Built-in over-current protection circuit that prevents

the destruction of the IC due to output short circuits

 Built-in thermal shutdown circuit for protecting the IC

from damage due to overloading

 Built-in over- voltage protection circuit that prevents

the destruction of the IC due to power supply surges

●Key Specification

 Input Power Supply Voltage: 25V (Max.)

 Output voltage type: Fixed

 Output current: BAxxDD0xx series 2A (Max.)

BAxxCC0xx series 1A (Max.)

 Shutdown current: 0μA(Typ.)

 Operating temperature range: -40℃ to +125℃

●Applications

Used in DSP power supplies for DVD and CD players,

FPDs, televisions, personal computers or any other

consumer device

●Packages W (Typ.) x D (Typ.) x H (Max.)

HRP5 9.395mm x 10.54mm x 2.005mm

TO252-3 6.50 mm x 9.50mm x 2.50 mm

TO252-5 6.50 mm x 9.50mm x 2.50 mm

TO220FP-3 10.00 mm x 30.50mm x 4.60 mm

TO220FP-5 10.00 mm x 30.50mm x 4.60 mm

●Lineup matrix

■1A output BAxxCC0xx Series

Part Number Output voltage (V) Package

3.0 3.3 5.0 6.0 7.0 8.0 9.0 10.0 12.0 15.0

BAxxCC0WT ○ ○ ○ －○○○○○－ TO220FP-5

BAxxCC0WFP － ○ ○ ○○○○－○－ TO252-5

BAxxCC0T ○ ○ ○ ○○○○○○○ TO220FP-3

BAxxCC0FP ○ ○ ○ ○○○○○○○ TO252-3

■2A output BAxxDD0xx Series

Part Number Output voltage (V) Package

1.5 1.8 2.5 3.0 3.3 5.0 9.0 12.0 16.0

BAxxDD0WT ○ ○ ○ ○○○○○○TO220FP-5

BAxxDD0WHFP ○ ○ ○ ○○○○○○HRP5

BAxxDD0T ○ ○ ○ ○○○○○○TO220FP-3

TO252-5

TO220FP-5 TO220FP-3

HRP5 TO252-3

Datasheet

2/20

BAxxDD0xx BAxxCC0xx

TSZ02201-0R6R0A600130-1-2

TSZ22111･15･001 26.Jun.2012 Rev.001

www.rohm.com

●Ordering Information

B A x x x x 0 x x x x - x x

Part

Number

Output voltage

Output

Current

CC0 : 1A

DD0 : 2A

Shutdown Switch

W : Includes switch

None: without switch

Packa

ePackaging and forming specification

TR: Embossed tape and reel

(HRP5)

E2: Embossed tape and reel

(TO252-3,TO252-5)

None : Container Tube

(TO220FP-3,TO220FP-5)

HFP

: HRP5

: TO252-5

: TO252-3

: TO220FP-5

: TO220FP-3

●Lineup

■1A output BAxxCC0xx Series

Maximum output

current (Max.) Shutdown

Switch Package Output

voltage(Typ.) Orderable

Part Number

With Switch

TO252-5 Reel of 2000

3.3V BA033CC0WFP-E2

5.0V BA05CC0WFP-E2

6.0V BA06CC0WFP-E2

7.0V BA07CC0WFP-E2

8.0V BA08CC0WFP-E2

9.0V BA09CC0WFP-E2

12.0V BAJ2CC0WFP-E2

TO220FP-5 Tube of 500

3.0V BA03CC0WT

3.3V BA033CC0WT

5.0V BA05CC0WT

7.0V BA07CC0WT

8.0V BA08CC0WT

9.0V BA09CC0WT

10.0V BAJ0CC0WT

12.0V BAJ2CC0WT

No switch

TO252-3 Reel of 2000

3.0V BA03CC0FP-E2

3.3V BA033CC0FP-E2

5.0V BA05CC0FP-E2

6.0V BA06CC0FP-E2

7.0V BA07CC0FP-E2

8.0V BA08CC0FP-E2

9.0V BA09CC0FP-E2

10.0V BAJ0CC0FP-E2

12.0V BAJ2CC0FP-E2

15.0V BAJ5CC0FP-E2

TO220FP-3 Tube of 500

3.0V BA03CC0T

3.3V BA033CC0T

5.0V BA05CC0T

6.0V BA06CC0T

7.0V BA07CC0T

8.0V BA08CC0T

9.0V BA09CC0T

10.0V BAJ0CC0T

12.0V BAJ2CC0T

15.0V BAJ5CC0T

Datasheet

3/20

BAxxDD0xx BAxxCC0xx

TSZ02201-0R6R0A600130-1-2

TSZ22111･15･001 26.Jun.2012 Rev.001

www.rohm.com

■2A output BAxxDD0xx Series

Maximum output

current (Max.) Shutdown

Switch Package Output

voltage(Typ.) Orderable

Part Number

With Switch

TO220FP-5 Tube of 500

1.5V BA15DD0WT

1.8V BA18DD0WT

2.5V BA25DD0WT

3.0V BA30DD0WT

3.3V BA33DD0WT

5.0V BA50DD0WT

9.0V BA90DD0WT

12.0V BAJ2DD0WT

16.0V BAJ6DD0WT

HRP5 Reel of 2000

1.5V BA15DD0WHFP-TR

1.8V BA18DD0WHFP-TR

2.5V BA25DD0WHFP-TR

3.0V BA30DD0WHFP-TR

3.3V BA33DD0WHFP-TR

5.0V BA50DD0WHFP-TR

9.0V BA90DD0WHFP-TR

12.0V BAJ2DD0WHFP-TR

16.0V BAJ6DD0WHFP-TR

No switch TO220FP-3 Tube of 500

1.5V BA15DD0T

1.8V BA18DD0T

2.5V BA25DD0T

3.0V BA30DD0T

3.3V BA33DD0T

5.0V BA50DD0T

9.0V BA90DD0T

12.0V BAJ2DD0T

16.0V BAJ6DD0T

Datasheet

4/20

BAxxDD0xx BAxxCC0xx

TSZ02201-0R6R0A600130-1-2

TSZ22111･15･001 26.Jun.2012 Rev.001

www.rohm.com

●Block Diagrams / Pin Configurations / Pin Descriptions

BAxxCC0WFP/ BAxxDD0WHFP/ BAxxCC0WT/ BAxxDD0WT

PIN No. Pin Name Function

1 CTL Output voltage ON/OFF control

2 Vcc Power supply voltage input

3 N.C./GND Unconnected terminal/GND*1

4 OUT Voltage output

5 N.C. Unconnected terminal

Fin GND GND*2

*1 TO252-5=N.C.,TO220FP-5,HRP5=GND

*2 TO252-5,HRP5 only

BAxxCC0T/ BAxxCC0FP/ BAxxDD0T

PIN No. Pin Name Function

1 Vcc Power supply voltage input

2 N.C./GND Unconnected terminal/GND*1

3 OUT Voltage output

Fi GND GND*2

*1 TO252-3=N.C.,TO220FP-3=GND

*2 TO252-3 only

Fig.1

1 2 345

Fin Vcc

Driver

OVP TSD OCP

CTL Vcc N.C.

(TO252-5)

GND

(TO220FP-5,HRP5)

OUT N.C.

Vref

GND(TO252-5･HRP5)

Fig.2

(TO220FP-3)

1 23

Fin

Vcc

Driver

OVP TSD OCP

Vcc N.C. OUT

(TO252-3)

GND

Vref

GND(TO252-3)

HRP5

TOP VIEW

FIN

TO252-5

1 2 3 4 5 1 2 3 4 5

TO220FP-5

1 2 3 4 5

TO220FP-3

TO252-3

FIN

2 3

TOP VIEW

Datasheet

5/20

BAxxDD0xx BAxxCC0xx

TSZ02201-0R6R0A600130-1-2

TSZ22111･15･001 26.Jun.2012 Rev.001

www.rohm.com

●Absolute Maximum Ratings (Ta=25℃)

Parameter Symbol Ratings Unit

Input Power Supply Voltage*1 V

CC -0.3 to +35 V

Power Dissipation*2 Pd

2300(HRP5)

1300(TO252-5)

1200(TO252-3)

2000(TO220FP-3,5)

Operating Temperature Range Topr -40 to +125 ℃

Ambient Storage Temperature Tstg -55 to +150 ℃

Junction Temperature TjMAX. +150 ℃

Output Control Terminal Voltage*3 Vctl -0.3 to +Vcc V

Voltage Applied to the Tip *4 VCC peak +50 V

*1 Must not exceed Pd

*2 HRP5 : In cases in which Ta≧25℃ when a 70mm×70mm×1.6mm glass

epoxy board is used, the power is reduced by 18.4 mW/℃.

TO252FP-3 : In cases in which Ta≧25℃ when a 70mm×70mm×1.6mm glass

epoxy board is used, the power is reduced by 9.6 mW/℃.

TO252FP-5 : In cases in which Ta≧25℃ when a 70mm×70mm×1.6mm glass

epoxy board is used, the power is reduced by 10.4 mW/℃.

TO220FP-5 : No heat sink. When Ta≧25℃, the power is reduced by 16 mW/℃.

*3 Only for models with shutdown switches.

*4 Applied voltage : 200msec or less (tr≥1msec)

●Recommended Operatin g Ratings (Ta=25℃)

Parameter Symbol Ratings Unit

Min. Typ. Max.

Input

Power Supply

Voltage

BAxxCC0xx VCC 4.0 ― 25.0 V

BAxxDD0xx 3.0

― 25.0 V

Output Current BAxxCC0xx Io ― ― 1 A

BAxxDD0xx ― ― 2 A

Output Control Terminal Voltage Vctl 0 ― V

CC V

MAX200msec

(Voltage Supply more than 35V)

50V

35V

tr≧1msec

Datasheet

6/20

BAxxDD0xx BAxxCC0xx

TSZ02201-0R6R0A600130-1-2

TSZ22111･15･001 26.Jun.2012 Rev.001

www.rohm.com

●Electrical Characteristics

BAxxCC0 Series (Unless otherwise specified, Ta=25℃, VCTL=5V, Io=500mA Setting *5)

Parameter Symbol Limit Unit Conditions

Min. Typ. Max.

Output Voltage *6 Vo

Vo(T)×

0.98 Vo(T) Vo(T)×

1.02 V

Shut Down Current Isd － 0 10 μA VCTL=0V

Bias Current Ib － 2.5 5.0 mA VCTL=2V, Io=0mA

Dropout Voltage ΔVd － 0.3 0.5 V Vcc=Vo×0.95

Peak Output Current Io 1.0 －－ A

Ripple Rejection R.R. 45 55 － dB

f=120Hz, ein

=1Vrms,

Io=100mA

Line Regulation Reg.I － 20 100 mV

Vcc=Vo(T)+1→25V

Load Regulation Reg.L － 50 150 mV Io=5mA→1A

Temperature Coefficient of

Output Voltage *8 Tcvo － ±0.02 －％/℃Io=5mA,Tj=0 to 125℃

Output Short Current Ios － 0.40 － A Vcc=25V

ON Mode Voltage VthH 2.0 －－ V ACTIVE MODE, Io=0mA

OFF Mode Voltage VthL －－ 0.8 V OFF MODE, Io=0mA

Input High Current ICTL 100 200 300 μA VCTL=5V, Io=0mA

BAxxDD0 series (Unless otherwise specified, Ta=25℃, VCTL=3V, Vcc=VCCT*9)

Parameter Symbol Limit Unit Conditions

Min. Typ. Max.

Shut Down Current Isd － 0 10 μA VCTL=0V, Io=0mA

Bias Current Ib － 0.9 2.0 mA Io=0mA

Output Voltage *10 Vo Votyp×

0.99 Votyp Votyp×

1.01 V Io=200mA

Dropout Voltage 1 *11 ΔVd1 － 0.3 0.5 V

Vcc=0.95×Vo, Io=1A

Dropout Voltage 2 *11 ΔVd2 － 0.45 0.7 V Vcc=0.95×Vo, Io=2A

Peak Output Current Io 2.0 －－ A

Ripple Rejection R.R. － 55 － dB f=120Hz, ein*7=-20dBV, Io=100mA

Line Regulation Reg.I － 15 50 mV

Vcc=VCCT*9V→25V, Io=200mA

Load Regulation Reg.L － 50 200 mV Io=0mA→2A

Temperature Coefficient of

Output Voltage *8 Tcvo － ±0.02 － %/℃Io=5mA, Tj=0 to 125℃

CTL ON Mode Voltage Von 2.0 － Vcc V ACTIVE MODE, Io=0mA

CTL OFF Mode Voltage Voff －－ 0.8 V OFF MODE, Io=0mA

CTL Input Current ICTL － 60 120 μA VCTL=3V, Io=0mA

*5 Vo=3.3V:Vcc=8.3V, Vo=5V:Vcc=10V, Vo=6V:Vcc=11V, Vo=7V:Vcc=12V, Vo=8V:Vcc=13V, Vo=9V:Vcc=14V, Vo=12V:Vcc=17V

*6 Vo(T)＝3.3, 5.0, 6.0, 7.0, 8.0, 9.0,12V

*7 ein : Input Voltage Ripple

*8 Not 100% tested

*9 Vo=1.5V,1.8V,2.5V,3.0V：VCCT =4.0V､Vo=3.3V,5.0V：VCCT =7.0V､Vo=9V：VCCT =12.0V､Vo=12V：VCCT =14.0V､Vo=16V：VCCT =18.0V）

*10 Votyp=1.5V,1.8V,2.5V,3.0V,3.3V,5.0V,9.0V,12.0V,16.0V

*11 Vo≧3.0V

Datasheet

7/20

BAxxDD0xx BAxxCC0xx

TSZ02201-0R6R0A600130-1-2

TSZ22111･15･001 26.Jun.2012 Rev.001

www.rohm.com

●Typical Performance Curves

(Unless specified otherwise, Vcc=8.3V, Vo=3.3V, VCTL=5.0V, and Io=0mA)

BAxxCC0xx (BA33CC0WT)

Fig.5

Input Stability

(Io=500mA)

Fig.6

Load Stability

Fig.3

Circuit current

Fig.4

Input Stability

Datasheet

8/20

BAxxDD0xx BAxxCC0xx

TSZ02201-0R6R0A600130-1-2

TSZ22111･15･001 26.Jun.2012 Rev.001

www.rohm.com

●Typical Performance Curves - co ntinued

Fig.8

Ripple Rejection Characteristics

(Io=100mA)

Fig.9

Output Voltage

Temperature Characteristics

Fig.10

Circuit Current by load Level

(IOUT=0mA→1A)

Fig.7

Input/Output Voltage Difference

Io-△Vd Characteristics (Vcc＝2.95V)

Datasheet

9/20

BAxxDD0xx BAxxCC0xx

TSZ02201-0R6R0A600130-1-2

TSZ22111･15･001 26.Jun.2012 Rev.001

www.rohm.com

●Typical Performance Curves - co ntinued

Fig.12

CTL Voltage vs. Output Voltage

Fig.13

Overvoltage Operating

Characteristics (Io=200mA)

Fig.14

Thermal Shutdown

Circuit Characteristics

Fig.11

CTL Voltage vs. CTL Current

Datasheet

10/20

BAxxDD0xx BAxxCC0xx

TSZ02201-0R6R0A600130-1-2

TSZ22111･15･001 26.Jun.2012 Rev.001

www.rohm.com

●Typical Performance Curves - co ntinued

(Unless specified otherwise, Vcc=7.0V, Vo=5.0V, VCTL=3.0V, and Io=0mA)

BAxxDD0xx (BA50DD0WT)

Fig.16

Input Stability (Io=0mA)

Fig.17

Input Stability (Io=2A)

Fig.15

Circuit Current

Fig.18

Load Stability

Datasheet

11/20

BAxxDD0xx BAxxCC0xx

TSZ02201-0R6R0A600130-1-2

TSZ22111･15･001 26.Jun.2012 Rev.001

www.rohm.com

●Typical Performance Curves - co ntinued

Fig.20

Ripple Rejection Characteristics

Fig.21

Temperature Characteristics

Fig.19

Input/Output Voltage Difference

Fig.22

Circuit Current by Load Level

(lout=0mA→2A)

Datasheet

12/20

BAxxDD0xx BAxxCC0xx

TSZ02201-0R6R0A600130-1-2

TSZ22111･15･001 26.Jun.2012 Rev.001

www.rohm.com

●Typical Performance Curves - co ntinued

Fig.25

Overvoltage Operating

(lo=200mA)

Fig.26

Thermal Shutdown

Circuit Characteristics

Fig.23

CTL Voltage vs. CTL Current

Fig.24

CTL Voltage vs. Output Voltage

[V]

[BA50DD0WT]

Datasheet

13/20

BAxxDD0xx BAxxCC0xx

TSZ02201-0R6R0A600130-1-2

TSZ22111･15･001 26.Jun.2012 Rev.001

www.rohm.com

●I/O equivalence circuit

Fig.27

Fig.28

●Power Dissipation

Vcc

CTL

39kΩ 2kΩ

31kΩ

10kΩ

Vcc

OUT

Vcc

CTL

25kΩ

25kΩ 10kΩ

OUT

Vcc

Fig.29 Fig.30

Fig.31

0.0

0.4

0.8

1.2

1.6

2.0

0 25 50 75 100 125 150

Ambient temperatur e:Ta( ℃）

Power Dissi pati on:Pd(W )

Mounted on a Rohm standard board

Board size : 70×70×1.6 ㎜

Copper foil area :7×7㎜

TO252-5θja=96.2(℃/W)

1.30

0 25 50 75 100 125 150

Ambient temperature:Ta(℃）

Power Dissipation:Pd(W

)

(1)20.0

(2)2.0

When using a maximum heat sick : θj-c=6.25(℃/W)

When using an IC alone : θj-6=62.5(℃/W)

0 25 50 75 100 125 150

Ambient temperatur e:Ta( ℃）

Power Dissi pati on:Pd(W )

Board size : 70×70×1.6 ㎜

(board contains a thermal via)

Board front copper foil area : 10.5×10.5 ㎜2

①2-layer board (back surface copper foil area :15×15 ㎜2)

②2-layer board (back surface copper foil area :70×70 ㎜2)

③4-layer board (back surface copper foil area :70×70 ㎜2)

③7.3W

②5.5W

①2.3W

HRP-5 TO220FP-5

TO252-5

Datasheet

14/20

BAxxDD0xx BAxxCC0xx

TSZ02201-0R6R0A600130-1-2

TSZ22111･15･001 26.Jun.2012 Rev.001

www.rohm.com

When using at temperatures over Ta=25℃, please refer to the heat reducing characteristics shown in Fig.29 through 31.

The IC characteristics are closely related to the temperature at which the IC is used and if the temperature exceeds the

maximum junction temperature TjMAX., the elements may be damaged or destroyed. From the standpoints of instantaneous

destruction and long-term operating reliability, it is necessary give sufficient consideration to IC heat. In order to protect the

IC from thermal damage, it is necessary to operate it at temperatures lower than the maximum junction temperature TjMAX

of the IC.

Fig.30 shows the acceptable loss and heat reducing characteristics of the TO220FP package The portion shown by the

diagonal line is the acceptable loss range that can be used with the IC alone. Even when the ambient temperature Ta is a

normal temperature (25℃), the chip (junction) temperature Tj may be quite high so please operate the IC at temperatures

less than the acceptable loss Pd.

The method of calculating the power consumption Pc (W) is as follows.

Pc = (Vcc-Vo) × Io ＋ Vcc × Icca

Acceptable loss Pd≦Pc

Solving this for load current IO in order to operate within the acceptable loss:

Io≦

(Please refer to Fig.10 and 22 for Icca.)

It is then possible to find the maximum load current IoMAX with respect to the applied voltage Vcc at the time of thermal design.

・Calculation Example

Example 1) When Ta=85℃, Vcc=8.3V, Vo=3.3V, BA33DD0WT

Io≦ With the IC alone : θja=62.5℃/W → -16mW/℃

Io≦200mA (Icca : 2mA) 25℃=2000mW → 85℃=1040mW

Please refer to the above information and keep thermal designs within the scope of acceptable loss for all operating

temperature ranges.

The power consumption Pc of the IC when there is a short circuit (short between Vo and GND) is:

Pc=Vcc×(Icca＋Ishort)

*Ishort: Short circuit current

●Peripheral Circuit Considerations

・Vcc Terminal

Please attach a capacitor (greater than 0.33µF) between the Vcc and GND.

The capacitance values will differ depending on the application, so please take this into account when configuring the terminal.

・GND Terminal

Please be sure to keep the set ground and IC ground at the same potential level so that a potential difference does not

arise between them.

If a potential difference arises between the set ground and the IC ground, the preset voltage will not be outputted,

causing the system to become unstable. Therefore, please reduce the impedance by making the ground patterns as wide

as possible and by reducing the distance between the set ground and the IC ground as much as possible.

・CTL Terminal

The CTL terminal is turned ON at 2.0V and higher and OFF at 0.8V and lower within the operating power supply voltage range.

The power supply and the CTL terminal may be started up and shut down in any order without problems.

●Vo Terminal

Fig.32 Output Equivalent Circuit Fig.33 ESR-Io Characteristics Fig.34 ESR vs. Io Characteristics

(BAxxCC0) (BAxxDD0)

Please attach an anti-oscillation capacitor between Vo and GND. The capacitance of the capacitor may significantly change

due to factors such as temperature changes, making it impossible to completely stop oscillations. Please use a tantalum

capacitor or aluminum electrolysis capacitor with favorable characteristics and small internal series resistance (ESR) even

at low temperatures. The output fluctuates regardless of whether the ESR is large or small. Please use the IC within the

stable operating region while referring to the ESR characteristics reference data shown in Fig.32 through 34. In applications

where there are sudden load fluctuations, the use of a capacitor with large capacitance is recommended.

Pd – Vcc×Icca

Vcc－Vo

Vcc：

Vo：

Io：

Vcca：

Input voltage

Output voltage

Load current

Circuit current

1.04－8.3×Icca

OUT

22μ

OUTPUT CURRENT：lo(mA) 10000

0.1

Unstable operating region

Stable operating region

EFFECTIVE SERIES RESISTANCE:ESR [Ω]

10 100 1000

100

200 400 800 1000

0.1

Stable operating region

0 600

Unstable operating region

OUTPUT CURRENT：lo(mA)

EFFECTIVE SERIES RESISTANCE:ESR [Ω]

100

Datasheet

15/20

BAxxDD0xx BAxxCC0xx

TSZ02201-0R6R0A600130-1-2

TSZ22111･15･001 26.Jun.2012 Rev.001

www.rohm.com

●Operational Notes

1) Protection Circuits

Over-current Protection Circuit

A built-in over-current protection circuit corresponding to the current capacity prevents the destruction of the IC when there

are load shorts. This protection circuit is a “7”-shaped current control circuit that is designed such that the current is restricted

and does not latch even when a large current momentarily flows through the system with a high-capacitance capacitor.

However, while this protection circuit is effective for the prevention of destruction due to unexpected accidents, it is not

suitable for continuous operation or transient use. Please be aware when creating thermal designs that the overcurrent

protection circuit has negative current capacity characteristics with regard to temperature (Refer to Fig.6 and 18).

Thermal Shutdown Circuit (Thermal Protection)

This system has a built-in temperature protection circuit for the purpose of protecting the IC from thermal damage.

As shown above, this must be used within the range of acceptable loss, but if the acceptable loss happens to be

continuously exceeded, the chip temperature Tj increases, causing the temperature protection circuit to operate.

When the thermal shutdown circuit operates, the operation of the circuit is suspended. The circuit resumes operation

immediately after the chip temperature Tj decreases, so the output repeats the ON and OFF states (Please refer to

Fig.14 and 26 for the temperatures at which the temperature protection circuit operates).

There are cases in which the IC is destroyed due to thermal runaway when it is left in the overloaded state. Be sure to

avoid leaving the IC in the overloaded state.

Reverse Current

In order to prevent the destruction of the IC when a reverse current flows through the IC, it is recommended that a diode

be placed between the Vcc and Vo and a pathway be created so that the current can escape (Refer to Fig.35).

Fig.35 Bypass diode

2) This IC is bipolar IC that has a P-board (substrate) and P+ isolation layer between each devise, as shown in Fig.36. A

P-N junction is formed between this P-layer and the N-layer of each device, and the P-N junction operates as a parasitic

diode when the electric potential relationship is GND> Pin A, GND> Pin B, while it operates as a parasitic transistor when

the electric potential relationship is Pin B GND> Pin A. Parasitic devices are structurally inevitable in the IC. The

operation of parasitic devices induces mutual interference between circuits, causing malfunctions and eventually the

destruction of the IC. It is necessary to be careful not to use the IC in ways that would cause parasitic elements to

operate. For example, applying a voltage that is lower than the GND (P-board) to the input terminal.

Status of this document

The Japanese version of this document is formal specification. A customer may use this translation version only for a reference

to help reading the formal version.

If there are any differences in translation version of this document formal version takes priority.

OUT

Vcc

CTL GND

Reverse current

Fig.36 Example of the basic structure of a bipolar IC

(Pin A)

GND

P+

Resistor

Parasitic element

P P+

(Pin A)

Parasitic element

or transistor

(Pin B)

GND

Parasitic element

GND

N P

P+ P+

Parasitic element

or transistor

(Pin B) BE

Transistor (NPN)

GND

Datasheet

16/20

BAxxDD0xx BAxxCC0xx

TSZ02201-0R6R0A600130-1-2

TSZ22111･15･001 26.Jun.2012 Rev.001

www.rohm.com

●Physical Dimension Tape and Reel Information

(Unit : mm)

TO252-3

21 3

0.8

0.65 0.65

1.5

2.5

0.75

FIN

6.5±0.2

2.3±0.2 2.3±0.2

0.5±0.1

1.0±0.2

2.3±0.2

9.5±0.5

0.5±0.1

5.5±0.2 1.5±0.2

5.1+0.2

0.1 C0.5

Direction of feed

1pin

Reel ∗ Order quantity needs to be multiple of the minimum quantity.

Embossed carrier tapeTape

Quantity

Direction

of feed

The direction is the 1pin of product is at the lower left when you hold

reel on the left hand and you pull out the tape on the right hand

2000pcs

( )

(Unit : mm)

TO252-5

123 54

0.8

0.5 1.27

1.5

2.5

FIN

6.5±0.2 2.3±0.2

0.5±0.1

1.0±0.2

9.5±0.5

0.5±0.1

5.5±0.2 1.5±0.2

C0.5

5.1+0.2

0.1

Direction of feed

1pin

Reel ∗ Order quantity needs to be multiple of the minimum quantity.

Embossed carrier tapeTape

Quantity

Direction

of feed

The direction is the 1pin of product is at the lower left when you hold

reel on the left hand and you pull out the tape on the right hand

2000pcs

( )

Direction of feed

1pin

Reel ∗ Order quantity needs to be multiple of the minimum quantity.

Embossed carrier tapeTape

Quantity

Direction

of feed

2000pcs

( )

The direction is the 1pin of product is at the upper right when you hold

reel on the left hand and you pull out the tape on the right hand

(Unit : mm)

HRP5

0.08 S

(MAX 9.745 include BURR)

54321

1.905±0.1

0.835±0.2

1.523±0.15

10.54±0.13

−0.05

+0.1

0.27

4.5°

(6.5)

8.82 ± 0.1

9.395±0.125

0.73±0.1

1.72

0.08±0.05

(7.49)

8.0±0.13 1.017±0.2

1.2575

−4.5°

+5.5°

(Unit : mm)

TO220FP-3

231

+0.4

3.2±0.1

0.55

17.0

12.0±0.2

8.0±0.2

2.54±0.5

13.5Min.

5.0±0.2

0.8

2.54±0.5

1.3

−0.1

+0.3

10.0

7.0

1.8±0.2

−0.2

−0.1

+0.3

2.6±0.5

−0.05

+0.1

+0.2

−0.1

+0.3

4.5

2.8

∗ Order quantity needs to be multiple of the minimum quantity.

TubeContainer

Quantity

Direction of feed 500pcs

Direction of products is fixed in a container tube

Datasheet

17/20

BAxxDD0xx BAxxCC0xx

TSZ02201-0R6R0A600130-1-2

TSZ22111･15･001 26.Jun.2012 Rev.001

www.rohm.com

●Marking Diagrams

(Unit : mm)

TO220FP-5

7.0

10.0

2.8

4.5

1.778 0.5±0.1

1.2

0.8

1.8±0.28.0±0.2

0.7

12.0±0.2

17.0

13.5Min.

φ3.2±0.1

−0.2

+0.4

+0.3

−0.1

+0.2

+0.3

−0.1

+0.3

−0.1

23451

2.85

∗ Order quantity needs to be multiple of the minimum quantity.

TubeContainer

Quantity

Direction of feed 500pcs

Direction of products is fixed in a container tube

HRP5 (TOP VIEW)

Part Number Marking

LOT Number

1PIN MARK

TO220FP-3 (TOP VIEW)

Part Number Marking

LOT Number

TO220FP-5 (TOP VIEW)

Part Number Marking

LOT Number

TO252-3

(TOP VIEW)

Part Number Marking

LOT Number

TO252-5

(TOP VIEW)

Part Number Marking

LOT Number

Datasheet

18/20

BAxxDD0xx BAxxCC0xx

TSZ02201-0R6R0A600130-1-2

TSZ22111･15･001 26.Jun.2012 Rev.001

www.rohm.com

■1A output BAxxCC0xx Series

Orderable

Part Number Package Part Number

Marking

BA033CC0WFP-E2

TO252-5

033CC0W

BA05CC0WFP-E2 05CC0W

BA06CC0WFP-E2 06CC0W

BA07CC0WFP-E2 07CC0W

BA08CC0WFP-E2 08CC0W

BA09CC0WFP-E2 09CC0W

BAJ2CC0WFP-E2 J2CC0W

BA03CC0WT

TO220FP-5

03CC0W

BA033CC0WT 033CC0W

BA05CC0WT 05CC0W

BA07CC0WT 07CC0W

BA08CC0WT 08CC0W

BA09CC0WT 09CC0W

BAJ0CC0WT J0CC0W

BAJ2CC0WT J2CC0W

BA03CC0FP-E2

TO252-3

03CC0

BA033CC0FP-E2 033CC0

BA05CC0FP-E2 05CC0

BA06CC0FP-E2 06CC0

BA07CC0FP-E2 07CC0

BA08CC0FP-E2 08CC0

BA09CC0FP-E2 09CC0

BAJ0CC0FP-E2 J0CC0

BAJ2CC0FP-E2 J2CC0

BAJ5CC0FP-E2 J5CC0

BA03CC0T

TO220FP-3

03CC0

BA033CC0T 033CC0

BA05CC0T 05CC0

BA06CC0T 06CC0

BA07CC0T 07CC0

BA08CC0T 08CC0

BA09CC0T 09CC0

BAJ0CC0T J0CC0

BAJ2CC0T J2CC0

BAJ5CC0T J5CC0

Datasheet

19/20

BAxxDD0xx BAxxCC0xx

TSZ02201-0R6R0A600130-1-2

TSZ22111･15･001 26.Jun.2012 Rev.001

www.rohm.com

■2A output BAxxDD0xx Series

Orderable

Part Number Package Part Number

Marking

BA15DD0WT

TO220FP-5

15DD0W

BA18DD0WT 18DD0W

BA25DD0WT 25DD0W

BA30DD0WT 30DD0W

BA33DD0WT 33DD0W

BA50DD0WT 50DD0W

BA90DD0WT 90DD0W

BAJ2DD0WT J2DD0W

BAJ6DD0WT J6DD0W

BA15DD0WHFP-TR

HRP5

15DD0W

BA18DD0WHFP-TR 18DD0W

BA25DD0WHFP-TR 25DD0W

BA30DD0WHFP-TR 30DD0W

BA33DD0WHFP-TR 33DD0W

BA50DD0WHFP-TR 50DD0W

BA90DD0WHFP-TR 90DD0W

BAJ2DD0WHFP-TR J2DD0W

BAJ6DD0WHFP-TR J6DD0W

BA15DD0T

TO220FP-3

15DD0

BA18DD0T 18DD0

BA25DD0T 25DD0

BA30DD0T 30DD0

BA33DD0T 33DD0

BA50DD0T 50DD0

BA90DD0T 90DD0

BAJ2DD0T J2DD0

BAJ6DD0T J6DD0

Datasheet

20/20

BAxxDD0xx BAxxCC0xx

TSZ02201-0R6R0A600130-1-2

TSZ22111･15･001 26.Jun.2012 Rev.001

www.rohm.com

●Revision History

Date Revision Changes

26.Jun.2012 001 New Release

Datasheet

Notice - Rev.003

Notice

●General Precaution

1) Before you use our Products, you are requested to carefully read this document and fully understand its contents.

ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of any

ROHM’s Products against warning, caution or note contained in this document.

2) All information contained in this document is current as of the issuing date and subject to change without any prior

notice. Before purchasing or using ROHM’s Products, please confirm the latest information with a ROHM sales

representative.

●Precaution on using ROHM Products

1) Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment,

OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you

intend to use our Products in devices requiring extremely high reliability (such as medical equipment, transport

equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car

accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or

serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.

Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any

damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific

Applications.

2) ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor

products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate

safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which

a failure or malfunction of our Products may cause. The following are examples of safety measures:

[a] Installation of protection circuits or other protective devices to improve system safety

[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure

3) Our Products are designed and manufactured for use under standard conditions and not under any special or

extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way

responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any

special or extraordinary environments or conditions. If you intend to use our Products under any special or

extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of

product performance, reliability, etc, prior to use, must be necessary:

[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents

[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust

[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,

H2S, NH3, SO2, and NO2

[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves

[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items

[f] Sealing or coating our Products with resin or other coating materials

[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of

flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning

residue after soldering

[h] Use of the Products in places subject to dew condensation

4) The Products are not subject to radiation-proof design.

5) Please verify and confirm characteristics of the final or mounted products in using the Products.

6) In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse) is applied,

confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power

exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect

product performance and reliability.

7) De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual

ambient temperature.

8) Confirm that operation temperature is within the specified range described in the product specification.

9) ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in

this document.

Datasheet

Notice - Rev.003

●Precaution for Mounting / Circuit board design

1) When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product

performance and reliability.

2) In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the

ROHM representative in advance.

For details, please refer to ROHM Mounting specification

●Precautions Regarding Application Examples and External Circuits

1) If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the

characteristics of the Products and external components, including transient characteristics, as well as static

characteristics.

2) You agree that application notes, reference designs, and associated data and information contained in this document

are presented only as guidance for Products use. Therefore, in case you use such information, you are solely

responsible for it and you must exercise your own independent verification and judgment in the use of such information

contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses

incurred by you or third parties arising from the use of such information.

●Precaution for Electrostatic

This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper

caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be

applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,

isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).

●Precaution for Storage / Transportation

1) Product performance and soldered connections may deteriorate if the Products are stored in the places where:

[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2

[b] the temperature or humidity exceeds those recommended by ROHM

[c] the Products are exposed to direct sunshine or condensation

[d] the Products are exposed to high Electrostatic

2) Even under ROHM recommended storage condition, solderability of products out of recommended storage time period

may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is

exceeding the recommended storage time period.

3) Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads

may occur due to excessive stress applied when dropping of a carton.

4) Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of

which storage time is exceeding the recommended storage time period.

●Precaution for Product Label

QR code printed on ROHM Products label is for ROHM’s internal use only.

●Precaution for Disposition

When disposing Products please dispose them properly using an authorized industry waste company.

●Precaution for Foreign Exchange and Foreign Trade act

Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act,

please consult with ROHM representative in case of export.

●Precaution Regarding Intellectual Property Rights

1) All information and data including but not limited to application example contained in this document is for reference

only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any

other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable

for infringement of any intellectual property rights or other damages arising from use of such information or data.:

2) No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any

third parties with respect to the information contained in this document.

Datasheet

Notice - Rev.003

●Other Precaution

1) The information contained in this document is provided on an “as is” basis and ROHM does not warrant that all

information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or

liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or

concerning such information.

2) This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.

3) The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written

consent of ROHM.

4) In no event shall you use in any way whatsoever the Products and the related technical information contained in the

Products or this document for any military purposes, including but not limited to, the development of mass-destruction

weapons.

5) The proper names of companies or products described in this document are trademarks or registered trademarks of

ROHM, its affiliated companies or third parties.