LTM2881 Complete Isolated RS485/RS422 Module Transceiver + Power Description Features RS485/RS422 Transceiver: 2500VRMS for 1 Minute nn UL-CSA Recognized File #E151738 nn CSA Component Acceptance Notice 5A nn Isolated DC Power: 5V at Up to 200mA nn No External Components Required nn 20Mbps or Low EMI 250kbps Data Rate nn High ESD: 15kV HBM on Transceiver Interface nn High Common Mode Transient Immunity: 30kV/s nn Integrated Selectable 120 Termination nn 3.3V (LTM2881-3) or 5.0V (LTM2881-5) Operation nn 1.62V to 5.5V Logic Supply Pin for Flexible Digital Interface nn Maximum Continuous Working Voltage: 560V PEAK nn High Input Impedance Failsafe RS485 Receiver nn Current Limited Drivers and Thermal Shutdown nn Compatible with TIA/EIA-485-A and PROFIBUS nn High Impedance Output During Internal Fault Condition nn Low Current Shutdown Mode (< 10A) nn General Purpose CMOS Isolated Channel nn 15mm x 11.25mm BGA and LGA Packages nn Applications The LTM(R)2881 is a complete galvanically isolated full-duplex RS485/RS422 Module(R) (micromodule) transceiver. No external components are required. A single supply powers both sides of the interface through an integrated, isolated, low noise, efficient 5V output DC/DC converter. Coupled inductors and an isolation power transformer provide 2500VRMS of isolation between the line transceiver and the logic interface. This device is ideal for systems where the ground loop is broken allowing for large common mode voltage variation. Uninterrupted communication is guaranteed for common mode transients greater than 30kV/s. Maximum data rates are 20Mbps or 250kbps in slew limited mode. Transmit data, DI and receive data, RO, are implemented with event driven low jitter processing. The receiver has a one-eighth unit load supporting up to 256 nodes per bus. A logic supply pin allows easy interfacing with different logic levels from 1.62V to 5.5V, independent of the main supply. Enhanced ESD protection allows this part to withstand up to 15kV (human body model) on the transceiver interface pins to isolated supplies and 10kV through the isolation barrier to logic supplies without latch-up or damage. Isolated RS485/RS422 Interface Industrial Networks nn Breaking RS485 Ground Loops nn Isolated PROFIBUS-DP Networks nn nn L, LT, LTC, LTM, Linear Technology, the Linear logo and Module are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Typical Application Isolated Half-Duplex RS485 Module Transceiver LTM2881 Operating Through 35kV/s CM Transients 3.3V (LTM2881-3) 5V (LTM2881-5) VCC PWR ISOLATION BARRIER VL RO MULTIPLE SWEEPS OF COMMON MODE TRANSIENTS RE TE DE DI LTM2881 VCC2 A 5V AVAILABLE CURRENT: 150mA (LTM2881-5) 100mA (LTM2881-3) 500V/DIV DI B TWISTED-PAIR CABLE Y 1V/DIV 1V/DIV 50ns/DIV Z GND RO 2881 TA01a GND2 2881 TA01 2881fi For more information www.linear.com/LTM2881 1 LTM2881 Absolute Maximum Ratings Pin Configuration (Note 1) VCC to GND................................................... -0.3V to 6V VCC2 to GND2................................................ -0.3V to 6V VL to GND..................................................... -0.3V to 6V Interface Voltages (A, B, Y, Z) to GND2......................... VCC2 -15V to 15V (A-B) with Terminator Enabled...............................6V Signal Voltages ON, RO, DI, DE, RE, TE, DOUT to GND.......................... -0.3V to VL +0.3V Signal Voltages SLO, DIN to GND2.....................................-0.3V to VCC2 +0.3V Operating Temperature Range LTM2881C................................................ 0C to 70C LTM2881I..............................................-40C to 85C LTM2881H.......................................... -40C to 105C LTM2881MP....................................... -55C to 105C Maximum Internal Operating Temperature........ 125C Storage Temperature Range................... -55C to 150C Peak Package Body Reflow Temperature............... 245C 2 TOP VIEW 1 A 2 DOUT TE 3 4 5 6 7 8 DI DE RE RO VL ON B VCC GND C D E F G H J GND2 K L DIN SLO Y Z BGA PACKAGE 32-PIN (15mm x 11.25mm x 3.42mm) TJMAX = 125C, JA = 32.2C/W, JCTOP = 27.2C/W, JCBOTTOM = 20.9C/W, JB = 26.4C/W, WEIGHT = 1g B A VCC2 LGA PACKAGE 32-PIN (15mm x 11.25mm x 2.8mm) TJMAX = 125C, JA = 31.1C/W, JCTOP = 27.3C/W, JCBOTTOM = 19.5C/W, JB = 25.1C/W, WEIGHT = 1g 2881fi For more information www.linear.com/LTM2881 LTM2881 Order Information PART NUMBER LTM2881CY-3#PBF LTM2881IY-3#PBF LTM2881HY-3#PBF LTM2881HY-3 LTM2881MPY-3#PBF LTM2881MPY-3 LTM2881CY-5#PBF LTM2881IY-5#PBF LTM2881HY-5#PBF LTM2881HY-5 LTM2881MPY-5#PBF LTM2881MPY-5 LTM2881CV-3#PBF LTM2881IV-3#PBF LTM2881HV-3#PBF LTM2881CV-5#PBF LTM2881IV-5#PBF LTM2881HV-5#PBF INPUT VOLTAGE http://www.linear.com/product/LTM2881#orderinfo PART MARKING DEVICE FINISH CODE PAD OR BALL FINISH SAC305 (RoHS) 3V to 3.6V SnPb (63/37) SAC305 (RoHS) SnPb (63/37) SnPb (63/37) SAC305 (RoHS) SnPb (63/37) 3V to 3.6V LTM2881Y-3 e0 e1 e0 BGA e1 LTM2881Y-5 3 e0 e1 e0 LTM2881V-3 Au (RoHS) 4.5V to 5.5V MSL RATING e1 SAC305 (RoHS) 4.5V to 5.5V PACKAGE TYPE e4 LTM2881V-5 LGA TEMPERATURE RANGE 0C to 70C -40C to 85C -40C to 105C -40C to 105C -55C to 105C -55C to 105C 0C to 70C -40C to 85C -40C to 105C -40C to 105C -55C to 105C -55C to 105C 0C to 70C -40C to 85C -40C to 105C 0C to 70C -40C to 85C -40C to 105C * Device temperature grade is indicated by a label on the shipping container. * Pad or ball finish code is per IPC/JEDEC J-STD-609. * Recommended BGA and LGA PCB Assembly and Manufacturing Procedures: www.linear.com/umodule/pcbassembly * Terminal Finish Part Marking: www.linear.com/leadfree * This product is moisture sensitive. For more information, go to: www.linear.com/umodule/pcbassembly * This product is not recommended for second side reflow. For more information, go to: www.linear.com/BGA-assy * LGA and BGA Package and Tray Drawings: www.linear.com/packaging 2881fi For more information www.linear.com/LTM2881 3 LTM2881 Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. LTM2881-3 VCC = 3.3V, LTM2881-5 VCC = 5.0V, VL = 3.3V, GND = GND2 = 0V, ON = VL unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN TYP MAX l l 3.0 4.5 3.3 5.0 3.6 5.5 l 1.62 UNITS Power Supply VCC VCC Supply Voltage VL VL Supply Voltage 5.5 V ICCPOFF VCC Supply Current in Off Mode ON = 0V l 0 10 A ICCS VCC Supply Current in On Mode LTM2881-3 DE = 0V, RE = VL , No Load LTM2881-5 DE = 0V, RE = VL , No Load l l 20 15 30 25 mA mA VCC2 Regulated VCC2 Output Voltage, Loaded LTM2881-3 DE = 0V, RE = VL , ILOAD = 100mA LTM2881-5 DE = 0V, RE = VL , ILOAD = 150mA LTM2881-3, H/MP-Grade, I LOAD = 90mA l l l VCC2NOLOAD Regulated VCC2 Output Voltage, No Load LTM2881-3 LTM2881-5 DE = 0V, RE = VL , No Load 4.75 4.75 4.75 5.0 5.0 4.8 5.0 V V V V V 5.35 V Efficiency ICC2 = 100mA, LTM2881-5 (Note 2) 62 % VCC2 Short-Circuit Current DE = 0V, RE = VL , VCC2 = 0V 200 mA |VOD| Differential Driver Output Voltage R = (Figure 1) R = 27 (RS485) (Figure 1) R = 50 (RS422) (Figure 1) |VOD| Difference in Magnitude of Driver R = 27 or R = 50 (Figure 1) Differential Output Voltage for Complementary Output States VOC Driver Common Mode Output Voltage ICC2S Driver VCC2 VCC2 VCC2 V V V l 0.2 V R = 27 or R = 50 (Figure 1) l 3 V |VOC| Difference in Magnitude of Driver R = 27 or R = 50 (Figure 1) Common Mode Output Voltage for Complementary Output States l 0.2 V IOZD Driver Three-State (High Impedance) Output Current on Y and Z DE = 0V, (Y or Z) = -7V, +12V DE = 0V, (Y or Z) = -7V, +12V, H/MP-Grade l l 10 50 A A IOSD Maximum Driver Short-Circuit Current - 7V (Y or Z) 12V (Figure 2) l - 250 250 mA RIN Receiver Input Resistance RE = 0V or VL , VIN = -7V, -3V, 3V, 7V, 12V (Figure 3) RE = 0V or VL , VIN = -7V, -3V, 3V, 7V, 12V (Figure 3), H/MP-Grade l l 96 48 125 125 RTE Receiver Termination Resistance Enabled TE = VL , VAB = 2V, VB = - 7V, 0V, 10V (Figure 8) l 108 120 IIN Receiver Input Current (A, B) ON = 0V VCC2 = 0V or 5V, VIN = 12V (Figure 3) ON = 0V VCC2 = 0V or 5V, VIN = 12V (Figure 3), H/MP-Grade l l ON = 0V VCC2 = 0V or 5V, VIN = -7V (Figure 3) ON = 0V VCC2 = 0V or 5V, VIN = -7V (Figure 3), H/MP-Grade l l -100 -145 -7V B 12V l -0.2 l l l 2.1 2.1 Receiver VTH Receiver Differential Input Threshold Voltage (A-B) VTH Receiver Input Failsafe Hysteresis B = 0V Receiver Input Failsafe Threshold B = 0V 4 k k 156 125 250 A A 0.2 25 -0.2 -0.05 V mV 0 V 2881fi For more information www.linear.com/LTM2881 LTM2881 Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. LTM2881-3 VCC = 3.3V, LTM2881-5 VCC = 5.0V, VL = 3.3V, GND = GND2 = 0V, ON = VL unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS Logic VIL Logic Input Low Voltage 1.62V VL 5.5V l Logic Input High Voltage DIN SLO DI, TE, DE, ON, RE: VL 2.35V 1.62V VL < 2.35V l l 0.67*VCC2 2 V V l l 0.67*VL 0.75*VL V V VIH 0.4 V IINL Logic Input Current VHYS Logic Input Hysteresis (Note 2) VOH Output High Voltage Output High, ILOAD = -4mA (Sourcing), 5.5V VL 3V Output High, ILOAD = -1mA (Sourcing), 1.62V VL < 3V l VL -0.4 V l VL -0.4 V Output Low, ILOAD = 4mA (Sinking), 5.5V VL 3V Output High, ILOAD = 1mA (Sinking), 1.62V VL < 3V l 0.4 V l 0.4 V VOL Output Low Voltage 0 l 1 150 A mV IOZR Three-State (High Impedance) Output Current on RO RE = VL , 0V RO VL l 1 A IOSR Short-Circuit Current 0V (RO or DOUT) VL l 85 mA Switching Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. LTM2881-3 VCC = 3.3V, LTM2881-5 VCC = 5.0V, VL = 3.3V, GND = GND2 = 0V, ON = VL unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS Driver SLO = VCC2 fMAX Maximum Data Rate (Note 3) tPLHD tPHLD Driver Input to Output RDIFF = 54, CL = 100pF (Figure 4) l 20 60 85 Mbps ns tPD Driver Input to Output Difference |tPLHD - tPHLD| RDIFF = 54, CL = 100pF (Figure 4) l 1 8 ns tSKEWD Driver Output Y to Output Z RDIFF = 54, CL = 100pF (Figure 4) l 1 8 ns tRD tFD Driver Rise or Fall Time RDIFF = 54, CL = 100pF (Figure 4) l 4 12.5 ns tZLD , tZHD , tLZD , tHZD Driver Output Enable or Disable Time RL = 500, CL = 50pF (Figure 5) l 170 ns Driver SLO = GND2 fMAX Maximum Data Rate (Note 3) tPLHD tPHLD Driver Input to Output RDIFF = 54, CL = 100pF (Figure 4) 250 1 1.55 s tPD Driver Input to Output Difference |tPLHD - tPHLD| RDIFF = 54, CL = 100pF (Figure 4) 50 500 ns tSKEWD Driver Output Y to Output Z RDIFF = 54, CL = 100pF (Figure 4) 200 500 ns tRD tFD Driver Rise or Fall Time RDIFF = 54, CL = 100pF (Figure 4) 0.9 1.5 s l kbps 2881fi For more information www.linear.com/LTM2881 5 LTM2881 switching Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. LTM2881-3 VCC = 3.3V, LTM2881-5 VCC = 5.0V, VL = 3.3V, GND = GND2 = 0V, ON = VL unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN tZLD , tZHD , tLZD , tHZD Driver Output Enable or Disable Time RL = 500, CL = 50pF (Figure 5) l tPLHR tPHLR Receiver Input to Output CL = 15pF, VCM = 2.5V, |VAB| = 1.4V, tR and tF < 4ns, (Figure 6) l tSKEWR Differential Receiver Skew |tPLHR - tPHLR| CL = 15pF (Figure 6) tRR tFR TYP MAX UNITS 400 ns 100 140 ns l 1 8 ns Receiver Output Rise or Fall Time CL = 15pF (Figure 6) l 3 12.5 ns tZLR , tZHR , tLZR , tHZR Receiver Output Enable Time RL =1k, CL = 15pF (Figure 7) l 50 ns tRTEN , tRTZ Termination Enable or Disable Time RE = 0V, DE = 0V, VAB = 2V, VB = 0V (Figure 8) l 100 s CL = 15pF, tR and tF < 4ns l 60 100 ns ON l 325 800 s Receiver Generic Logic Input DIN to DOUT Input to Output tPLHL1 tPHLL1 Power Supply Generator VCC2 -GND2 Supply Start-Up Time (0V to 4.5V) VL, No Load Isolation Characteristics otherwise noted. TA = 25C, LTM2881-3 VCC = 3.3V, LTM2881-5 VCC = 5.0V, VL = 3.3V unless SYMBOL PARAMETER CONDITIONS VISO Rated Dielectric Insulation Voltage 1 Minute (Derived from 1 Second Test) 1 Second (Notes 5, 6) Common Mode Transient Immunity Maximum Working Insulation Voltage LTM2881-3 VCC = 3.3V, LTM2881-5 VCC = 5V, VL = ON = 3.3V, VCM = 1kV, t = 33ns (Note 2) (Notes 2, 5) Partial Discharge Comparative Tracking Index Depth of Erosion Distance Through Insulation Input to Output Resistance Input to Output Capacitance Creepage Distance VPR = 1050 VPEAK (Note 2) IEC 60112 (Note 2) IEC 60112 (Note 2) (Note 2) (Notes 2, 5) (Notes 2, 5) (Notes 2, 5) VIORM CTI DTI Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: Guaranteed by design and not subject to production test. Note 3: Maximum Data rate is guaranteed by other measured parameters and is not tested directly. 6 MIN TYP MAX UNITS 2500 4400 VRMS VDC 30 kV/s 560 400 VPEAK VRMS pC VRMS mm mm pF mm 5 600 0.017 0.06 109 6 9.48 Note 4: This Module transceiver includes overtemperature protection that is intended to protect the device during momentary overload conditions. Junction temperature will exceed 125C when overtemperature protection is active. Continuous operation above specified maximum operating junction temperature may result in device degradation or failure. Note 5: Device considered a 2-terminal device. Pin group A1 through B8 shorted together and pin group K1 through L8 shorted together. Note 6: The rated dielectric insulation voltage should not be interpreted as a continuous voltage rating. 2881fi For more information www.linear.com/LTM2881 LTM2881 Typical Performance Characteristics TA = 25C, LTM2881-3 VCC = 3.3V, LTM2881-5 VCC = 5.0V, VL = 3.3V unless otherwise noted. 2.0 80 1.5 1.5 75 1.0 0.5 0 DRIVER PROP DELAY (ns) 2.0 1.0 0.5 0 -0.5 -0.5 -1.0 -50 -25 0 25 50 75 TEMPERATURE (C) 100 -1.0 -50 125 -25 0 25 50 75 TEMPERATURE (C) 100 4.5 126 4.0 124 3.5 122 120 118 116 1.5 0.5 0 125 OUTPUT LOW R = 100 3 R = 54 2 0 10 20 30 40 50 OUTPUT CURRENT (mA) 60 0 -50 70 -25 0 25 50 75 TEMPERATURE (C) 100 125 2881 G06 Receiver Propagation Delay vs Temperature 4 Supply Current vs Data Rate 200 120 180 3 2 1 115 SUPPLY CURRENT (mA) RECEIVER PROP DELAY (ns) SOURCE 110 105 100 160 R = 54 (LTM2881-3) 140 120 100 80 60 40 95 20 SINK 2 3 4 OUTPUT CURRENT (mA) R= 4 2881 G05 Receiver Output Voltage vs Output Current (Source and Sink) 125 2881 G03 1 2881 G04 1 100 5 OUTPUT HIGH 2.0 112 0 0 25 50 75 TEMPERATURE (C) 6 2.5 1.0 100 -25 Driver Differential Output Voltage vs Temperature 3.0 114 0 50 -50 125 OUTPUT VOLTAGE (V) 128 OUTPUT VOLTAGE (V) RESISTANCE () 5.0 0 25 50 75 TEMPERATURE (C) 60 Driver Output Low/High Voltage vs Output Current 130 -25 65 2881 G02 RTERM vs Temperature 110 -50 70 55 2881 G01 OUTPUT VOLTAGE (V) Driver Propagation Delay vs Temperature Driver Skew vs Temperature DRIVER SKEW (ns) RECEIVER SKEW (ns) Receiver Skew vs Temperature 5 2881 G07 90 -50 -25 0 25 50 75 TEMPERATURE (C) 100 125 2881 G08 R = 100 (LTM2881-3) R = 54 (LTM2881-5) R = 100 (LTM2881-5) R = (LTM2881-3) R = (LTM2881-5) 0 0.1 1 DATA RATE (Mbps) 10 2881 G09 2881fi For more information www.linear.com/LTM2881 7 LTM2881 Typical Performance Characteristics TA = 25C, LTM2881-3 VCC = 3.3V, LTM2881-5 VCC = 5.0V, VL = 3.3V unless otherwise noted. 6 LTM2881-3, VCC = 3.3V 250 200 LTM2881-5, VCC = 5V 150 100 50 200 LTM2881-5 (RS485 60mA) 150 LTM2881-5 (RS485 90mA) 100 LTM2881-3 (RS485 60mA) LTM2881-5 5 VOLTAGE (V) 300 ICC CURRENT (mA) VCC2 vs Load Current 250 SURPLUS CURRENT (mA) 350 VCC2 Surplus Current vs Temperature VCC Supply Current vs Temperature at ILOAD = 100mA on VCC2 LTM2881-3 4 3 50 LTM2881-3 (RS485 90mA) 0 -50 -25 0 25 50 75 TEMPERATURE (C) 100 125 0 -50 -25 0 25 50 75 TEMPERATURE (C) 2881 G10 70 100 125 2 2881 G11 VCC2 Power Efficiency 10 20 40 60 80 100 120 140 160 180 VCC2 LOAD CURRENT (mA) 2881 G12 VCC2 Load Step (100mA) VCC2 Noise LTM2881-5 VCC2 100mV/DIV EFFICIENCY (%) 60 50 LTM2881-3 10mV/DIV 40 ILOAD 50mA/DIV 30 20 10 100s/DIV 0 150 50 100 ICC2 OUTPUT CURRENT (mA) 2881 G14 200s/DIV 2881 G15 200 2881 G13 8 2881fi For more information www.linear.com/LTM2881 LTM2881 Pin Functions LOGIC SIDE (VCC , VL, GND) ISOLATED SIDE (VCC2, GND2) DOUT (Pin A1): General Purpose Logic Output. Logic output connected through isolation path to DIN . Under the condition of an isolation communication failure DOUT is in a high impedance state. DIN (Pin L1): General Purpose Isolated Logic Input. Logic input on the isolated side relative to VCC2 and GND2. A logic high on DIN will generate a logic high on DOUT. A logic low on DIN will generate a logic low on DOUT. TE (Pin A2): Terminator Enable. A logic high enables a termination resistor (typically 120) between pins A and B. SLO (Pin L2): Driver Slew Rate Control. A low input, relative to GND2, will force the driver into a reduced slew rate mode for reduced EMI. A high input, relative to GND2, puts the driver into full speed mode to support maximum data rates. DI (Pin A3): Driver Input. If the driver outputs are enabled (DE high), then a low on DI forces the driver noninverting output (Y) low and the inverting output (Z) high. A high on DI, with the driver outputs enabled, forces the driver noninverting output (Y) high and inverting output (Z) low. DE (Pin A4): Driver Enable. A logic low disables the driver leaving the outputs Y and Z in a high impedance state. A logic high enables the driver. RE (Pin A5): Receiver Enable. A logic low enables the receiver output. A logic high disables RO to a high impedance state. RO (Pin A6): Receiver Output. If the receiver output is enabled (RE low) and if A - B is > 200mV, RO is a logic high, if A - B is < -200mV RO is a logic low. If the receiver inputs are open, shorted, or terminated without a valid signal, RO will be high. Under the condition of an isolation communication failure RO is in a high impedance state. VL (Pin A7): Logic Supply. Interface supply voltage for pins RO, RE, TE, DI, DE, DOUT, and ON. Recommended operating voltage is 1.62V to 5.5V. Internally bypassed to GND with 2.2F. Y (Pin L3): Non Inverting Driver Output. High impedance when the driver is disabled. Z (Pin L4): Inverting Driver Output. High impedance when the driver is disabled. B (Pin L5): Inverting Receiver Input. Impedance is > 96k in receive mode with TE low or unpowered. A (Pin L6): Non Inverting Receiver Input. Impedance is > 96k in receive mode with TE low or unpowered. VCC2 (Pins L7-L8): Isolated Supply Voltage. Internally generated from VCC by an isolated DC/DC converter and regulated to 5V. Internally bypassed to GND2 with 2.2F. GND2 (Pins K1-K8): Isolated Side Circuit Ground. The pads should be connected to the isolated ground and/or cable shield. ON (Pin A8): Enable. Enables power and data communication through the isolation barrier. If ON is high the part is enabled and power and communications are functional to the isolated side. If ON is low the logic side is held in reset and the isolated side is unpowered. GND (Pins B1-B5): Circuit Ground. VCC (Pins B6-B8): Supply Voltage. Recommended operating voltage is 3V to 3.6V for LTM2881-3 and 4.5V to 5.5V for LTM2881-5. Internally bypassed to GND with 2.2F. 2881fi For more information www.linear.com/LTM2881 9 LTM2881 Block Diagram VCC 2.2F VCC2 5V REG ISOLATED DC/DC CONVERTER 2.2F VL 2.2F A RO RX B RE ISOLATED COMM INTERFACE DE ISOLATED COMM INTERFACE 120 DI Y DX ON Z SLO TE DIN DOUT GND GND2 2881 BD = LOGIC SIDE COMMON = ISOLATED SIDE COMMON Test Circuits Y GND OR VL DI Y + DRIVER VOD - Z R R GND OR VL + - DI IOSD DRIVER VOC Z 2881 F01 -7V TO 12V 2881 F02 Figure 1. Driver DC Characteristics Figure 2. Driver Output Short-Circuit Current IIN VIN + - + - A OR B B OR A RECEIVER 2881 F03 V RIN = IN IIN Figure 3. Receiver Input Current and Input Resistance 10 2881fi For more information www.linear.com/LTM2881 LTM2881 TEST CIRCUITs DI Y DI VL tPLHD 0V tPHLD tSKEWD CL DRIVER RDIFF Y, Z VOD 1/2 VOD CL Z 90% 2881 F04a (Y-Z) 10% 0 0 90% 10% tRD tFD 2881 F04b Figure 4. Driver Timing Measurement RL Y VL OR GND DI CL GND OR VCC2 RL Z 1/2 VL 0V tZLD VCC2 Y OR Z DRIVER DE VL DE CL VCC2 OR GND 2881 F05a tLZD 1/2 VCC2 0.5V 0.5V 1/2 VCC2 Z OR Y 0V tZHD 2881 F05b tHZD Figure 5. Driver Enable and Disable Timing Measurements tR VAB/2 VCM VAB/2 VAB A-B -VAB A B RECEIVER RO CL 2881 F06a RO VL 0 90% 10% tF 90% 0 10% tPLHR 90% 1/2 VL 10% tRR tPHLR 1/2 VL 90% 10% tFR 2881 F06b Figure 6. Receiver Propagation Delay Measurements 2881fi For more information www.linear.com/LTM2881 11 LTM2881 TEST CIRCUITs VL RE 0V OR VCC2 B VCC2 OR 0V 1/2 VL 0V A RL RO RECEIVER VL OR GND CL RE tZLR VL RO 1/2 VL VOL RO VOH 0.5V 0.5V 1/2 VL 0V 2881 F07a tLZR 2881 F07b tZHR tHZR Figure 7. Receiver Enable/Disable Time Measurements IA A RO RTE = + - RECEIVER VAB IA TE VAB VL 1/2 VL 0V IA B + - TE tRTEN tRTZ 90% 10% VB 2881 F08 Figure 8. Termination Resistance and Timing Measurements Functional Table LOGIC INPUTS MODE A, B Y, Z RO DC/DC CONVERTER TERMINATOR ON RE TE DE 1 0 0 0 Receive RIN Hi-Z Enabled On Off 1 0 0 1 Transceiver RIN Driven Enabled On Off 1 1 0 1 Transmit RIN Driven Hi-Z On Off 1 0 1 0 Receive + Term On RTE Hi-Z Enabled On On 0 X X X Off RIN Hi-Z Hi-Z Off Off 12 2881fi For more information www.linear.com/LTM2881 LTM2881 Applications Information Overview The LTM2881 Module transceiver provides a galvanicallyisolated robust RS485/RS422 interface, powered by an integrated, regulated DC/DC converter, complete with decoupling capacitors. A switchable termination resistor is integrated at the receiver input to provide proper termination to the RS485 bus. The LTM2881 is ideal for use in networks where grounds can take on different voltages. Isolation in the LTM2881 blocks high voltage differences and eliminates ground loops and is extremely tolerant of common mode transients between ground potentials. Error free operation is maintained through common mode events greater than 30kV/s providing excellent noise isolation. Module Technology The LTM2881 utilizes isolator Module technology to translate signals and power across an isolation barrier. Signals on either side of the barrier are encoded into pulses and translated across the isolation boundary using coreless transformers formed in the Module substrate. This system, complete with data refresh, error checking, safe shutdown on fail, and extremely high common mode immunity, provides a robust solution for bidirectional signal isolation. The Module technology provides the means to combine the isolated signaling with our RS485 transceiver and powerful isolated DC/DC converter in one small package. DC/DC Converter rate, and external pins are supplied for extra decoupling (optional) and heat dissipation. The logic supplies, VCC and VL have a 2.2F decoupling capacitance to GND and the isolated supply VCC2 has a 2.2F decoupling capacitance to GND2 within the Module package. VCC2 Output The on-board DC/DC converter provides isolated 5V power to output VCC2. VCC2 is capable of suppling up to 1W of power at 5V in the LTM2881-5 option and up to 600mW of power in the LTM2881-3 option. This surplus current is available to external applications. The amount of surplus current is dependent upon the implementation and current delivered to the RS485 driver and line load. An example of available surplus current is shown in the Typical Performance Characteristics graph, VCC2 Surplus Current vs Temperature. Figure 19 demonstrates a method of using the VCC2 output directly and with a switched power path that is controlled with the isolated RS485 data channel. Driver The driver provides full RS485 and RS422 compatibility. When enabled, if DI is high, Y-Z is positive. When the driver is disabled, both outputs are high impedance with less than 10A of leakage current over the entire common mode range of -7V to 12V, with respect to GND2. Driver Overvoltage and Overcurrent Protection The driver outputs are protected from short circuits to any voltage within the absolute maximum range of (VCC2 -15V) to (GND2 +15V) levels. The maximum VCC2 current in this condition is 250mA. If the pin voltage exceeds about 10V, current limit folds back to about half of the peak value to reduce overall power dissipation and avoid damaging the part. The LTM2881 contains a fully integrated isolated DC/DC converter, including the transformer, so that no external components are necessary. The logic side contains a fullbridge driver, running about 2MHz, and is AC-coupled to a single transformer primary. A series DC blocking capacitor prevents transformer saturation due to driver duty cycle imbalance. The transformer scales the primary voltage, and is rectified by a full-wave voltage doubler. This topology eliminates transformer saturation caused by secondary imbalances. The device also features thermal shutdown protection that disables the driver and receiver output in case of excessive power dissipation (See Note 4 in the Electrical Characteristics section). The DC/DC converter is connected to a low dropout reg ulator (LDO) to provide a regulated low noise 5V output. SLO Mode The internal power solution is sufficient to support the transceiver interface at its maximum specified load and data The LTM2881 features a logic-selectable reduced slew rate mode (SLO mode) that softens the driver output edges to For more information www.linear.com/LTM2881 2881fi 13 LTM2881 Y-Z 10dB/DIV Y-Z 10dB/DIV Applications Information 0 6.25 FREQUENCY (MHz) 12.5 0 6.25 FREQUENCY (MHz) 12.5 2881 F09b 2881 F09a Figure 9a. Frequency Spectrum SLO Mode 125kHz Input Figure 9b. Normal Mode Frequency Spectrum 125kHz Input reduce EMI emissions from equipment and data cables. The reduced slew rate mode is entered by taking the SLO pin low to GND2, where the data rate is limited to about 250kbps. Slew limiting also mitigates the adverse effects of imperfect transmission line termination caused by stubs or mismatched cables. of the bus when A-B is above the input failsafe threshold for longer than about 3s with a hysteresis of 25mV. This failsafe feature is guaranteed to work for inputs spanning the entire common mode range of -7V to 12V. Figures 9a and 9b show the frequency spectrums of the LTM2881 driver outputs in normal and SLO mode operating at 250kbps. SLO mode significantly reduces the high frequency harmonics. Receiver and Failsafe With the receiver enabled, when the absolute value of the differential voltage between the A and B pins is greater than 200mV, the state of RO will reflect the polarity of (A-B). During data communication the receiver detects the state of the input with symmetric thresholds around 0V. The symmetric thresholds preserve duty cycle for attenuated signals with slow transition rates on high capacitive busses, or long cable lengths. The receiver incorporates a failsafe feature that guarantees the receiver output to be a logic-high during an idle bus, when the inputs are shorted, left open or terminated, but not driven. The failsafe feature eliminates the need for system level integration of network pre-biasing by guaranteeing a logic-high on RO under the conditions of an idle bus. Further network biasing constructed to condition transient noise during an idle state is unnecessary due to the common mode transient rejection of the LTM2881. The failsafe detector monitors A and B in parallel with the receiver and detects the state 14 The receiver output is internally driven high (to VL) or low (to GND) with no external pull-up needed. When the receiver is disabled the RO pin becomes Hi-Z with leakage of less than 1A for voltages within the supply range. Receiver Input Resistance The receiver input resistance from A or B to GND2 is greater than 96k permitting up to a total of 256 receivers per system without exceeding the RS485 receiver loading specification. High temperature H-/MP-Grade operation reduces the input resistance to 48k permitting 128 receivers on the bus. The input resistance of the receiver is unaffected by enabling/disabling the receiver or by powering/unpowering the part. The equivalent input resistance looking into A and B is shown in Figure 10. A >96k 60 TE 60 >96k 2881 F10 B Figure 10. Equivalent Input Resistance into A and B 2881fi For more information www.linear.com/LTM2881 LTM2881 Applications Information Switchable Termination Proper cable termination is very important for signal fidelity. If the cable is not terminated with its characteristic impedance, reflections will distort the signal waveforms. The integrated switchable termination resistor provides logic control of the line termination for optimal perfor mance when configuring transceiver networks. Supply Current The static supply current is dominated by power delivered to the termination resistance. Power supply current increases with data rate due to capacitive loading. Figure 14 shows supply current versus data rate for three different loads for the circuit configuration of Figure 4. Supply current increases with additional external applications drawing current from VCC2. 130 128 126 RESISTANCE () When the TE pin is high, the termination resistor is enabled and the differential resistance from A to B is 120. Figure 11 shows the I/V characteristics between pins A and B with the termination resistor enabled and disabled. The resistance is maintained over the entire RS485 common mode range of -7V to 12V as shown in Figure 12. The integrated termination resistor has a high frequency response which does not limit performance at the maximum specified data rate. Figure 13 shows the magnitude and phase of the termination impedance versus frequency. The termination resistor cannot be enabled by TE if the device is unpowered, ON is low or the LTM2881 is in thermal shutdown. 124 122 120 118 116 114 112 110 -10 -5 0 5 10 COMMON MODE VOLTAGE (V) 2881 G11 2881 F11 Figure 11. Curve Trace Between A and B with Termination Enabled and Disabled 150 250 230 PHASE 210 -10 MAGNITUDE -20 110 -30 100 0.1 -40 SUPPLY CURRENT (mA) 0 130 120 Figure 12. Termination Resistance vs Common Mode Voltage 10 PHASE (DEGREES) MAGNITUDE () 140 15 190 170 LTM2881-3 R=54 CL=1000p R=54 CL=100p R=54 CL=0 150 130 110 90 LTM2881-5 R=54 CL=1000p R=54 CL=100p R=54 CL=0 70 1 FREQUENCY (MHz) 10 50 2881 F13 Figure 13. Termination Magnitude and Phase vs Frequency 0.1 1 DATA RATE (Mbps) 10 2881 F14 Figure 14. Supply Current vs Data Rate 2881fi For more information www.linear.com/LTM2881 15 LTM2881 Applications Information PROFIBUS Applications * Input and Output decoupling is not required, since these components are integrated within the package. An additional bulk capacitor with a value of 6.8F to 22F is recommended. The high ESR of this capacitor reduces board resonances and minimizes voltage spikes caused by hot plugging of the supply voltage. For EMI sensitive applications, an additional low ESL ceramic capacitor of 1F to 4.7F, placed as close to the power and ground terminals as possible, is recommended. Alternatively, a number of smaller value parallel capacitors may be used to reduce ESL and achieve the same net capacitance. * Do not place copper on the PCB between the inner columns of pads. This area must remain open to withstand the rated isolation voltage. * The use of solid ground planes for GND and GND2 is recommended for non-EMI critical applications to optimize signal fidelity, thermal performance, and to minimize RF emissions due to uncoupled PCB trace conduction. The drawback of using ground planes, where EMI is of concern, is the creation of a dipole antenna structure which can radiate differential voltages formed between GND and GND2. If ground planes are used it is recommended to minimize their area, and use contiguous planes as any openings or splits can exacerbate RF emissions. * For large ground planes a small capacitance ( 330pF) from GND to GND2, either discrete or embedded within the substrate, provides a low impedance current return path for the module parasitic capacitance, minimizing any high frequency differential voltages and substantially reducing radiated emissions. Discrete capacitance will not be as effective due to parasitic ESL. In addition, voltage rating, leakage, and clearance must be considered for component selection. Embedding the capacitance within the PCB substrate provides a near ideal capacitor and eliminates component selection issues; however, the PCB must be 4 layers. Care must be exercised in applying either technique to insure the voltage rating of the barrier is not compromised. The LTM2881 can be used in PROFIBUS-DP networks where isolation is required. The standard PROFIBUS termination differs from RS485 termination and is shown in Figure 15. If used in this way, the internal termination should remain disabled (TE low). The 390 resistors in Figure 15 pre-bias the bus so that when the line is not driven, the receiver delivers a high output. Since the LTM2881 uses a fail-safe receiver, the pre-biasing resistors are not necessary and standard RS485 termination can be used with control from TE. VCC2, provides an isolated source for the external termination resistor as shown in the Figure 15. When using the LTM2881 in PROFIBUS applications, it is recommended that no additional loads are connected to VCC2 in order to maintain the specified driver output swing. 3.3V (LTM2881-3) 5V (LTM2881-5) VCC VCC2 PWR VL ISOLATION BARRIER RO DE DI TE GND 390 A PROFIBUS CABLE TYPE A B Y 220 SHIELD Z GND2 LTM2881 390 2881 F15 Figure 15. PROFIBUS-DP Connections with Termination PCB Layout Considerations The high integration of the LTM2881 makes PCB layout very simple. However, to optimize its electrical isolation characteristics, EMI, and thermal performance, some layout considerations are necessary. * Under heavily loaded conditions VCC and GND current can exceed 300mA. Sufficient copper must be used on the PCB to insure resistive losses do not cause the supply voltage to drop below the minimum allowed level. Similarly, the VCC2 and GND2 conductors must be sized to support any external load current. These heavy copper traces will also help to reduce thermal stress and improve the thermal conductivity. 16 2881fi For more information www.linear.com/LTM2881 LTM2881 Applications Information TECHNOLOGY Figure 16a. Low EMI Demo Board Layout Figure 16b. Low EMI Demo Board Layout (DC1746A), Top Layer Figure 16c. Low EMI Demo Board Layout (DC1746A), Inner Layer 1 2881fi For more information www.linear.com/LTM2881 17 LTM2881 Applications Information Figure 16d. Low EMI Demo Board Layout (DC1746A), Inner Layer 2 Figure 16e. Low EMI Demo Board Layout (DC1746A), Bottom Layer 60 DETECTOR = QuasiPeak 50 RBW = 120kHz, VBW = 300kHz SWEEP TIME = 17sec 40 # OF POINTS = 501 dBV/m 30 20 10 0 -10 -20 -30 DC1746A-B CISPR 22 CLASS 8 LIMIT 0 100 200 300 400 500 600 700 800 900 1000 FREQUENCY (MHz) 2881 F17 Figure 17. Low EMI Demo Board Emissions 18 2881fi For more information www.linear.com/LTM2881 LTM2881 Applications Information The PCB layout in Figures 16a to 16e show the low EMI demo board for the LTM2881. The demo board uses a combination of EMI mitigation techniques, including both embedded PCB bridge capacitance and discrete GND to GND2 capacitors. Two safety rated type Y2 capacitors are used in series, manufactured by Murata, part number GA342QR7GF471KW01L. The embedded capacitor effectively suppresses emissions above 400MHz, whereas the discrete capacitors are more effective below 400MHz. EMI performance is shown in Figure 17, measured using a Gigahertz Transverse Electromagnetic (GTEM) cell and method detailed in IEC 61000-4-20, "Testing and Measurement Techniques - Emission and Immunity Testing in Transverse Electromagnetic Waveguides." Cable Length versus Data Rate RF, Magnetic Field Immunity The LTM2881 has been independently evaluated and has successfully passed the RF and magnetic field immunity testing requirements per European Standard EN 55024, in accordance with the following test standards: EN 61000-4-3 Radiated, Radio-Frequency, Electromagnetic Field Immunity EN 61000-4-8 Power Frequency Magnetic Field Immunity EN 61000-4-9 Pulsed Magnetic Field Immunity Tests were performed using an unshielded test card designed per the data sheet PCB layout recommendations. Specific limits per test are detailed in Table 1. Table 1 For a given data rate, the maximum transmission distance is bounded by the cable properties. A typical curve of cable length versus data rate compliant with the RS485 standard is shown in Figure 18. Three regions of this curve reflect different performance limiting factors in data transmission. In the flat region of the curve, maximum distance is determined by resistive loss in the cable. The downward sloping region represents limits in distance and rate due to the AC losses in the cable. The solid vertical line represents the specified maximum data rate in the RS485 standard. The dashed line at 250kbps shows the maximum data rate when SLO is low. The dashed line at 20Mbps shows the maximum data rate when SLO is high. TEST EN 61000-4-3, Annex D FREQUENCY FIELD STRENGTH 80MHz to 1GHz 10V/m 1.4MHz to 2GHz 3V/m 2GHz to 2.7GHz 1V/m EN 61000-4-8, Level 4 50Hz and 60Hz 30A/m EN 61000-4-8, Level 5 60Hz 100A/m* EN 61000-4-9, Level 5 Pulse 1000A/m *Non IEC Method CABLE LENGTH (FT) 10k LOW-EMI MODE MAX DATA RATE 1k NORMAL MODE MAX DATA RATE 100 RS485 MAX DATA RATE 10 10k 100k 1M 10M DATA RATE (bps) 100M 2881 F18 Figure 18. Cable Length vs Data Rate 2881fi For more information www.linear.com/LTM2881 19 LTM2881 Typical Applications VCC VCC VCC ISOLATION BARRIER RE TE DE DI RE TE Y DE Z DI DIN GND FAULT RO B DOUT LTM2881 PWR VL A RO 330k VCC LTM2881 B Y Z GND GND2 A ISOLATION BARRIER VL GND2 2881 F20 2881 F19 Figure 20. Full-Duplex RS485 Connection Figure 19. Isolated System Fault Detection VCC 1.8V VCC RE TE DE DI OFF ON PWR ISOLATION BARRIER VL RO A GND IRLML6402 B LTM2881 330k Z DIN DOUT CMOS OUTPUT REGULATED 5V SWITCHED 5V VCC2 GND2 CMOS INPUT 2881 F21 Figure 21. Switched 5V Power with Isolated CMOS Logic Connection with Low Voltage Interface VCC VCCB ISOLATION BARRIER RO RE DE DI LTM2881 LTM2881 PWR A B Y Y 51 10nF Z 51 A 51 Z GND GND2 VCC PWR ISOLATION BARRIER VCC VL VL DE DI RE RO B 51 10nF GND2 BUS INHERITED GND 2881 F22 B Figure 22. 4-Wire Full Duplex Self Biasing for Unshielded CAT5 Connection 20 2881fi For more information www.linear.com/LTM2881 1.905 3.175 SUGGESTED PCB LAYOUT TOP VIEW 0.000 aaa Z 0.630 0.025 O 32x 0.635 PACKAGE TOP VIEW E 0.635 4 1.905 3.175 4.445 Y X D For more information www.linear.com/LTM2881 6.350 5.080 0.000 5.080 6.350 aaa Z 2.45 - 2.55 SYMBOL A A1 A2 b b1 D E e F G aaa bbb ccc ddd eee NOM 3.42 0.60 2.82 0.75 0.63 15.0 11.25 1.27 12.70 8.89 DIMENSIONS 0.15 0.10 0.20 0.30 0.15 MAX 3.62 0.70 2.92 0.90 0.66 NOTES DETAIL B PACKAGE SIDE VIEW TOTAL NUMBER OF BALLS: 32 MIN 3.22 0.50 2.72 0.60 0.60 b1 0.27 - 0.37 SUBSTRATE ddd M Z X Y eee M Z DETAIL A Ob (32 PLACES) DETAIL B MOLD CAP ccc Z A1 A2 A Z (Reference LTC DWG # 05-08-1851 Rev D) // bbb Z PIN "A1" CORNER 4.445 BGA Package 32-Lead (15mm x 11.25mm x 3.42mm) e b 7 5 G 4 e 3 PACKAGE BOTTOM VIEW 6 2 1 L K J H G F E D C B A DETAILS OF PIN #1 IDENTIFIER ARE OPTIONAL, BUT MUST BE LOCATED WITHIN THE ZONE INDICATED. THE PIN #1 IDENTIFIER MAY BE EITHER A MOLD OR MARKED FEATURE 4 3 TRAY PIN 1 BEVEL COMPONENT PIN "A1" 7 ! PACKAGE IN TRAY LOADING ORIENTATION LTMXXXXXX Module BGA 32 1112 REV D PACKAGE ROW AND COLUMN LABELING MAY VARY AMONG Module PRODUCTS. REVIEW EACH PACKAGE LAYOUT CAREFULLY 6. SOLDER BALL COMPOSITION IS 96.5% Sn/3.0% Ag/0.5% Cu 5. PRIMARY DATUM -Z- IS SEATING PLANE BALL DESIGNATION PER JESD MS-028 AND JEP95 3 2. ALL DIMENSIONS ARE IN MILLIMETERS 7 SEE NOTES PIN 1 SEE NOTES NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994 F b 8 DETAIL A LTM2881 Package Description Please refer to http://www.linear.com/product/LTM2881#packaging for the most recent package drawings. 2881fi 21 4 For more information www.linear.com/LTM2881 3.175 1.905 SUGGESTED PCB LAYOUT TOP VIEW 0.635 PACKAGE TOP VIEW 11.25 BSC 0.635 PAD "A1" CORNER 1.905 Y X 6.350 5.080 0.000 5.080 6.350 DETAIL c 15.00 BSC aaa Z 2.400 - 2.600 eee S X Y 0.290 - 0.350 SUBSTRATE DETAIL C 0.630 0.025 O 32x DETAIL B eee S X Y DETAILS OF PAD #1 IDENTIFIER ARE OPTIONAL, BUT MUST BE LOCATED WITHIN THE ZONE INDICATED. THE PAD #1 IDENTIFIER MAY BE EITHER A MOLD OR MARKED FEATURE 4 7 PACKAGE ROW AND COLUMN LABELING MAY VARY AMONG Module PRODUCTS. REVIEW EACH PACKAGE LAYOUT CAREFULLY SYMBOL TOLERANCE aaa 0.10 bbb 0.10 eee 0.05 ! 6. THE TOTAL NUMBER OF PADS: 32 5. PRIMARY DATUM -Z- IS SEATING PLANE LAND DESIGNATION PER JESD MO-222 3 2. ALL DIMENSIONS ARE IN MILLIMETERS NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994 DETAIL A 0.630 0.025 O 32x DETAIL B MOLD CAP 2.69 - 2.95 (Reference LTC DWG # 05-08-1773 Rev A) bbb Z 22 Z LGA Package 32-Lead (15mm x 11.25mm x 2.82mm) TRAY PIN 1 BEVEL COMPONENT PIN "A1" 12.70 BSC 8 DETAIL A 7 8.89 BSC 5 4 3 1.27 BSC 2 1 L K J H G F E D C B A 7 LGA 32 0113 REV A 3 PADS SEE NOTES PAD 1 PACKAGE IN TRAY LOADING ORIENTATION LTMXXXXXX Module PACKAGE BOTTOM VIEW 6 SEE NOTES LTM2881 Package Description Please refer to http://www.linear.com/product/LTM2881#packaging for the most recent package drawings. 2881fi 4.445 3.175 4.445 aaa Z LTM2881 Revision History REV DATE DESCRIPTION PAGE NUMBER A 3/10 Changes to Features, Description and Typical Application Add BGA Package to Pin Configuration, Order Information and Package Description Sections 1 2, 19 Changes to LGA Package in Pin Configuration Section 2 Changes to Electrical Characteristics Section 3 Changes to Graphs G09, G13, G14 6, 7 Update to Pin Functions 8 Update to Applications Information 12 Change to X-Axis on Figures 9a and 9b 13 Update to Supply Current Section 14 "PCB Layout Isolation Considerations" Section Replaced 15 RF, Magnetic Field Immunity Section Added 16 Changes to Related Parts 22 B 8/10 H-Grade parts added. Reflected throughout the data sheet. 1-22 C 5/11 HV-Grade parts removed. Reflected throughout the data sheet. 1-24 Updated the PCB Layout section. Updated the Related Parts. 15, 16, 17 24 D 1/12 HV and MPY parts added. Reflected throughout the data sheet. E 4/12 Added H/MP-Grade condition for IOZD 3 Corrected Figure 15 15 F 2/13 Storage Temperature Range corrected 2 G 4/14 Added lead finish part numbers 3 H 8/14 I 4/16 J 11/16 1-24 Added CTI and DTI parameters 6 ICC2S, VCC2 Short-Circuit Current: Deleted max spec. Added typical spec. Removed temp dot. 4 Added CSA information 1 Changed ICCS limits 4 Corrected LGA Part Marking 3 2881fi Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its information circuits as described herein will not infringe on existing patent rights. For more www.linear.com/LTM2881 23 LTM2881 Typical Application VCCC VCCA VCC LTM2881 PWR VL ISOLATION BARRIER CABLE SHIELD OR GROUND RETURN Y Y Z Z GND2 A VCC2 DE DI GND GND2 A RE TE C Z GND B VL RO PWR GND2 DI B Y DE A B VCC1 RE TE A PWR ISOLATION BARRIER RO VCC LTM2881 ISOLATION BARRIER GND DI DE TE RE RO VCC VL VCCB LTM2881 2881 F23 B B Figure 23. Multi-Node Network with End Termination and Single Ground Connection on Isolation Bus Related Parts PART NUMBER DESCRIPTION COMMENTS LTM2882 Dual Isolated RS232 Module Transceiver + Power 1Mbps, 10kV HBM ESD, 2500VRMS LTC1535 Isolated RS485 Transceiver 2500VRMS Isolation in Surface Mount Package LT1785 60V Fault-Protected Transceiver Half Duplex LT1791 60V Fault-Protected Transceiver Full Duplex LTC2861 20Mbps RS485 Transceivers with Integrated Switchable Termination Full Duplex 15kV ESD LTC2870/LTC2871 RS232/RS485 Multiprotocol Transceivers with Integrated Termination 20Mbps RS485 and 500kbps RS232, 26kV ESD, 3V to 5V Operation LTC2862/LTC2863/ 60V Fault Protected 3V to 5.5V RS485/RS422 Transceivers LTC2864/LTC2865 20Mbps or 250kbps, 15kV HBM ESD, 25V Common Mode Range LTM2883 SPI/Digital or I2C Isolated Module with Adjustable 5V and 12V Rails 2500VRMS Isolation with Power in BGA Package LTM2892 SPI/Digital or I2C Isolated Module 3500VRMS Isolation, 6 Channels 24 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 For more information www.linear.com/LTM2881 (408) 432-1900 FAX: (408) 434-0507 www.linear.com/LTM2881 2881fi LT 1116 REV J * PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 2009