LM3488,LM3488Q LM3488/LM3488Q High Efficiency Low-Side N-Channel Controller for Switching Regulators Literature Number: SNVS089L LM3488/LM3488Q High Efficiency Low-Side N-Channel Controller for Switching Regulators General Description Key Specifications The LM3488 is a versatile Low-Side N-FET high performance controller for switching regulators. It is suitable for use in topologies requiring low side FET, such as boost, flyback, SEPIC, etc. Moreover, the LM3488 can be operated at extremely high switching frequency in order to reduce the overall solution size. The switching frequency of LM3488 can be adjusted to any value between 100kHz and 1MHz by using a single external resistor or by synchronizing it to an external clock. Current mode control provides superior bandwidth and transient response, besides cycle-by-cycle current limiting. Output current can be programmed with a single external resistor. The LM3488 has built in features such as thermal shutdown, short-circuit protection and over voltage protection. Power saving shutdown mode reduces the total supply current to 5A and allows power supply sequencing. Internal soft-start limits the inrush current at start-up. Wide supply voltage range of 2.97V to 40V 100kHz to 1MHz Adjustable and Synchronizable clock frequency 1.5% (over temperature) internal reference 5A shutdown current (over temperature) Features LM3488Q is AEC-Q100 qualified and manufactured on an Automotive Grade Flow 8-lead Mini-SO8 (MSOP-8) package Internal push-pull driver with 1A peak current capability Current limit and thermal shutdown Frequency compensation optimized with a capacitor and a resistor Internal softstart Current Mode Operation Undervoltage Lockout with hysteresis Applications Distributed Power Systems Notebook, PDA, Digital Camera, and other Portable Applications Offline Power Supplies Set-Top Boxes Typical Application Circuit 10138844 Typical SEPIC Converter (c) 2011 National Semiconductor Corporation 101388 www.national.com LM3488/LM3488Q High Efficiency Low-Side N-Channel Controller for Switching Regulators October 17, 2011 LM3488/LM3488Q Connection Diagram 10138802 8 Lead Mini SO8 Package (MSOP-8 Package) Package Marking and Ordering Information Order Number Package Type Package Marking LM3488MM Supplied As S21B LM3488MMX 3500 units on Tape and Reel MSOP-8 LM3488QMM 1000 units on Tape and Reel SSKB LM3488QMMX Feature 1000 units on Tape and Reel 3500 units on Tape and Reel AEC-Q100 (Grade 1) qualified. Automotive Grade Production Flow* *Automotive Grade (Q) product incorporates enhanced manufacturing and support processes for the automotive market, including defect detection methodologies. Reliability qualification is compliant with the requirements and temperature grades defined in the AEC-Q100 standard. Automotive grade products are identified with the letter Q. For more information go to http://www.national.com/automotive. Pin Descriptions Pin Name Pin Number Description ISEN 1 Current sense input pin. Voltage generated across an external sense resistor is fed into this pin. COMP 2 Compensation pin. A resistor, capacitor combination connected to this pin provides compensation for the control loop. FB 3 Feedback pin. The output voltage should be adjusted using a resistor divider to provide 1.26V at this pin. AGND 4 Analog ground pin. PGND 5 Power ground pin. DR 6 Drive pin of the IC. The gate of the external MOSFET should be connected to this pin. FA/SYNC/SD 7 Frequency adjust, synchronization, and Shutdown pin. A resistor connected to this pin sets the oscillator frequency. An external clock signal at this pin will synchronize the controller to the frequency of the clock. A high level on this pin for 30s will turn the device off. The device will then draw less than 10A from the supply. VIN www.national.com 8 Power supply input pin. 2 If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Input Voltage FB Pin Voltage FA/SYNC/SD Pin Voltage Peak Driver Output Current (<10s) Power Dissipation Storage Temperature Range Junction Temperature ESD Susceptibilty Human Body Model (Note 2) 45V -0.4V < VFB < 7V -0.4V < VFA/SYNC/SD < 7V 1.0A Internally Limited -65C to +150C +150C 215C 260C -0.4V VDR 8V 600mV ILIM Pin Voltage Operating Ratings (Note 1) 2.97V VIN 40V Supply Voltage Junction Temperature Range Switching Frequency -40C TJ +125C 100kHz FSW 1MHz 2kV Electrical Characteristics Specifications in Standard type face are for TJ = 25C, and in bold type face apply over the full Operating Temperature Range. Unless otherwise specified, VIN = 12V, RFA = 40k Symbol VFB Parameter Feedback Voltage Conditions VCOMP = 1.4V, Typical Limit Units 1.2507/1.24 1.2753/1.28 V V(min) V(max) 1.26 2.97 VIN 40V VLINE Feedback Voltage Line Regulation 2.97 VIN 40V 0.001 %/V VLOAD Output Voltage Load Regulation IEAO Source/Sink 0.5 %/V (max) VUVLO Input Undervoltage Lock-out VUV(HYS) Fnom 2.85 Input Undervoltage Lock-out Hysteresis 170 Nominal Switching Frequency RFA = 40K 400 2.97 V V(max) 130 210 mV mV (min) mV (max) 360 430 kHz kHz(min) kHz(max) RDS1 (ON) Driver Switch On Resistance (top) IDR = 0.2A, VIN= 5V 16 RDS2 (ON) Driver Switch On Resistance (bottom) IDR = 0.2A 4.5 VDR (max) Maximum Drive Voltage Swing(Note 6) VIN < 7.2V VIN V VIN 7.2V 7.2 Dmax Maximum Duty Cycle(Note 7) 100 % Tmin (on) Minimum On Time 325 230 550 nsec nsec(min) nsec(max) 3.0 mA mA (max) 7 A A (max) 135/ 125 180/ 190 mV mV (min) mV (max) 250 415 mV mV (min) mV (max) ISUPPLY IQ VSENSE VSC Supply Current (switching) (Note 9) 2.7 Quiescent Current in Shutdown Mode VFA/SYNC/SD = 5V(Note 10), VIN = 5V Current Sense Threshold Voltage VIN = 5V Short-Circuit Current Limit Sense Voltage VIN = 5V 5 156 343 3 www.national.com LM3488/LM3488Q Lead Temperature MM Package Vapor Phase (60 sec.) Infared (15 sec.) DR Pin Voltage Absolute Maximum Ratings (Note 1) LM3488/LM3488Q Symbol VSL Parameter Internal Compensation Ramp VIN = 5V Voltage VSL ratio VSL/VSENSE VOVP Output Over-voltage Protection (with respect to feedback voltage) (Note 8) VOVP(HYS) Gm AVOL IEAO Conditions Limit Units 52 132 mV mV(min) mV(max) 0.30 0.70 (min) (max) 32/ 25 78/ 85 mV mV(min) mV(max) 20 110 mV mV(min) mV(max) 600/ 365 1000/ 1265 mho mho (min) mho (max) 26 44 V/V V/V (min) V/V (max) 80/ 50 140/ 180 A A (min) A (max) -100/ -85 -180/ -185 A A (min) A (max) 1.8 2.4 V V(min) V(max) 0.2 1.0 V V(min) V(max) 92 0.49 VCOMP = 1.4V 50 Output Over-Voltage VCOMP = 1.4V Protection Hysteresis(Note 8) 60 Error Ampifier Transconductance VCOMP = 1.4V IEAO = 100A (Source/Sink) 800 Error Amplifier Voltage Gain VCOMP = 1.4V IEAO = 100A (Source/Sink) 38 Error Amplifier Output Current Source, VCOMP = 1.4V, VFB = 0V (Source/ Sink) Sink, VCOMP = 1.4V, VFB = 1.4V VEAO Typical Error Amplifier Output Voltage Upper Limit Swing VFB = 0V COMP Pin = Floating Lower Limit VFB = 1.4V 110 -140 2.2 0.56 TSS Internal Soft-Start Delay VFB = 1.2V, VCOMP = Floating 4 msec Tr Drive Pin Rise Time Cgs = 3000pf, VDR = 0 to 3V 25 ns Tf Drive Pin Fall Time Cgs = 3000pf, VDR = 0 to 3V 25 ns VSD Shutdown and Synchronization signal threshold (Note 5) Output = High 1.27 Output = Low 1.4 V V (max) 0.3 V V (min) 0.65 ISD Shutdown Pin Current IFB Feedback Pin Current 15 nA TSD Thermal Shutdown 165 C Tsh Thermal Shutdown Hysteresis 10 C JA Thermal Resistance 200 C/W www.national.com VSD = 5V -1 VSD = 0V +1 MM Package 4 A Note 2: The human body model is a 100 pF capacitor discharged through a 1.5k resistor into each pin. Note 3: All limits are guaranteed at room temperature (standard type face) and at temperature extremes (bold type face). All room temperature limits are 100% tested. All limits at temperature extremes are guaranteed via correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL). Note 4: Typical numbers are at 25C and represent the most likely norm. Note 5: The FA/SYNC/SD pin should be pulled to VIN through a resistor to turn the regulator off. Note 6: The voltage on the drive pin, VDR is equal to the input voltage when input voltage is less than 7.2V. VDR is equal to 7.2V when the input voltage is greater than or equal to 7.2V. Note 7: The limits for the maximum duty cycle can not be specified since the part does not permit less than 100% maximum duty cycle operation. Note 8: The over-voltage protection is specified with respect to the feedback voltage. This is because the over-voltage protection tracks the feedback voltage. The over-voltage thresold can be calculated by adding the feedback voltage, VFB to the over-voltage protection specification. Note 9: For this test, the FA/SYNC/SD Pin is pulled to ground using a 40K resistor . Note 10: For this test, the FA/SYNC/SD Pin is pulled to 5V using a 40K resistor. Typical Performance Characteristics Unless otherwise specified, VIN = 12V, TJ = 25C. IQ vs Temperature & Input Voltage ISupply vs Input Voltage (Non-Switching) 10138803 10138834 ISupply vs VIN Switching Frequency vs RFA 10138835 10138804 5 www.national.com LM3488/LM3488Q Note 1: Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which operation of the device is intended to be functional. For guaranteed specifications and test conditions, see the Electrical Characteristics. LM3488/LM3488Q Frequency vs Temperature Drive Voltage vs Input Voltage 10138854 10138805 Current Sense Threshold vs Input Voltage COMP Pin Voltage vs Load Current 10138845 10138862 Efficiency vs Load Current (3.3V In and 12V Out) Efficiency vs Load Current (5V In and 12V Out) 10138859 www.national.com 10138858 6 Efficiency vs Load Current (3.3V In and 5V Out) 10138860 10138853 Error Amplifier Gain Error Amplifier Phase 10138855 10138856 COMP Pin Source Current vs Temperature Short Circuit Protection vs Input Voltage 10138857 10138836 7 www.national.com LM3488/LM3488Q Efficiency vs Load Current (9V In and 12V Out) LM3488/LM3488Q Compensation Ramp vs Compensation Resistor Shutdown Threshold Hysteresis vs Temperature 10138846 10138851 Current Sense Voltage vs Duty Cycle 10138852 www.national.com 8 LM3488/LM3488Q Functional Block Diagram 10138806 The voltage sensed across the sense resistor generally contains spurious noise spikes, as shown in Figure 1. These spikes can force the PWM comparator to reset the RS latch prematurely. To prevent these spikes from resetting the latch, a blank-out circuit inside the IC prevents the PWM comparator from resetting the latch for a short duration after the latch is set. This duration is about 150ns and is called the blank-out time. Under extremely light load or no-load conditions, the energy delivered to the output capacitor when the external MOSFET is on during the blank-out time is more than what is delivered to the load. An over-voltage comparator inside the LM3488 prevents the output voltage from rising under these conditions. The over-voltage comparator senses the feedback (FB pin) voltage and resets the RS latch under these conditions. The latch remains in reset state till the output decays to the nominal value. Functional Description The LM3488 uses a fixed frequency, Pulse Width Modulated (PWM), current mode control architecture. In a typical application circuit, the peak current through the external MOSFET is sensed through an external sense resistor. The voltage across this resistor is fed into the ISEN pin. This voltage is then level shifted and fed into the positive input of the PWM comparator. The output voltage is also sensed through an external feedback resistor divider network and fed into the error amplifier negative input (feedback pin, FB). The output of the error amplifier (COMP pin) is added to the slope compensation ramp and fed into the negative input of the PWM comparator. At the start of any switching cycle, the oscillator sets the RS latch using the SET/Blank-out and switch logic blocks. This forces a high signal on the DR pin (gate of the external MOSFET) and the external MOSFET turns on. When the voltage on the positive input of the PWM comparator exceeds the negative input, the RS latch is reset and the external MOSFET turns off. 9 www.national.com LM3488/LM3488Q 10138807 FIGURE 1. Basic Operation of the PWM comparator From the above equation, when D > 0.5, I1 will be greater than IO. In other words, the disturbance is divergent. So a very small perturbation in the load will cause the disturbance to increase. To prevent the sub-harmonic oscillations, a compensation ramp is added to the control signal, as shown in Figure 3. With the compensation ramp, SLOPE COMPENSATION RAMP The LM3488 uses a current mode control scheme. The main advantages of current mode control are inherent cycle-by-cycle current limit for the switch, and simpler control loop characteristics. It is also easy to parallel power stages using current mode control since as current sharing is automatic. Current mode control has an inherent instability for duty cycles greater than 50%, as shown in Figure 2. In Figure 2, a small increase in the load current causes the switch current to increase by IO. The effect of this load change, I1, is : 10138809 FIGURE 2. Sub-Harmonic Oscillation for D>0.5 www.national.com 10 LM3488/LM3488Q 10138811 FIGURE 3. Compensation Ramp Avoids Sub-Harmonic Oscillation The compensation ramp has been added internally in LM3488. The slope of this compensation ramp has been selected to satisfy most of the applications. The slope of the internal compensation ramp depends on the frequency. This slope can be calculated using the formula: In this equation, VSL is equal to 40.10-6RSL. Hence, MC = VSL.FS Volts/second In the above equation, VSL is the amplitude of the internal compensation ramp. Limits for VSL have been specified in the electrical characteristics. In order to provide the user additional flexibility, a patented scheme has been implemented inside the IC to increase the slope of the compensation ramp externally, if the need arises. Adding a single external resistor, RSL(as shown in Figure 4) increases the slope of the compensation ramp, MC by : VSL versus RSL has been plotted in Figure 5 for different frequencies. 10138813 FIGURE 4. Increasing the Slope of the Compensation Ramp 11 www.national.com LM3488/LM3488Q TABLE 1. TOFF(SYNC) (sec) RSYNC range (k) 1 5 to 13 2 20 to 40 3 40 to 65 4 55 to 90 5 70 to 110 6 85 to 140 7 100 to 160 8 120 to 190 9 135 to 215 10 150 to 240 It is also necessary to have the width of the synchronization pulse wider than the duty cycle of the converter (when DR pin is high and the switching point is low). It is also necessary to have the synchronization pulse width 300nsecs. The FA/SYNC/SD pin also functions as a shutdown pin. If a high signal (refer to the electrical characteristics for definition of high signal) appears on the FA/SYNC/SD pin, the LM3488 stops switching and goes into a low current mode. The total supply current of the IC reduces to less than 10A under these conditions. Figure 8 and Figure 9 show implementation of shutdown function when operating in Frequency adjust mode and synchronization mode respectively. In frequency adjust mode, connecting the FA/SYNC/SD pin to ground forces the clock to run at a certain frequency. Pulling this pin high shuts down the IC. In frequency adjust or synchronization mode, a high signal for more than 30s shuts down the IC. Figure 10 shows implementation of both frequency adjust with RFA resistor and frequency synchronization with RSYNC. The switching frequency is defined by RFA when a synchronization signal is not applied. When sync is applied it overrides the RFA setting. 10138851 FIGURE 5. VSL vs RSL FREQUENCY ADJUST/SYNCHRONIZATION/SHUTDOWN The switching frequency of LM3488 can be adjusted between 100kHz and 1MHz using a single external resistor. This resistor must be connected between FA/SYNC/SD pin and ground, as shown in Figure 6. Please refer to the typical performance characteristics to determine the value of the resistor required for a desired switching frequency. The LM3488 can be synchronized to an external clock. The external clock must be connected to the FA/SYNC/SD pin through a resistor, RSYNC as shown in Figure 7. The value of this resistor is dependent on the off time of the synchronization pulse, TOFF(SYNC). Table 1 shows the range of resistors to be used for a given TOFF(SYNC). 10138814 FIGURE 6. Frequency Adjust www.national.com 12 LM3488/LM3488Q 10138815 FIGURE 7. Frequency Synchronization 10138816 FIGURE 8. Shutdown Operation in Frequency Adjust Mode 10138817 FIGURE 9. Shutdown Operation in Synchronization Mode 10138887 FIGURE 10. Frequency Adjust or Frequency Synchronization vated. A comparator inside LM3488 reduces the switching frequency by a factor of 5 and maintains this condition till the short is removed. SHORT-CIRCUIT PROTECTION When the voltage across the sense resistor (measured on ISEN Pin) exceeds 350mV, short-circuit current limit gets acti- 13 www.national.com LM3488/LM3488Q Typical Applications The LM3488 may be operated in either continuous or discontinuous conduction mode. The following applications are designed for continuous conduction operation. This mode of operation has higher efficiency and lower EMI characteristics than the discontinuous mode. load and output capacitor. The ratio of these two cycles determines the output voltage. The output voltage is defined as: BOOST CONVERTER The most common topology for LM3488 is the boost or stepup topology. The boost converter converts a low input voltage into a higher output voltage. The basic configuration for a boost regulator is shown in Figure 11. In continuous conduction mode (when the inductor current never reaches zero at steady state), the boost regulator operates in two cycles. In the first cycle of operation, MOSFET Q is turned on and energy is stored in the inductor. During this cycle, diode D is reverse biased and load current is supplied by the output capacitor, COUT. In the second cycle, MOSFET Q is off and the diode is forward biased. The energy stored in the inductor is transferred to the (ignoring the drop across the MOSFET and the diode), or where D is the duty cycle of the switch, VD is the forward voltage drop of the diode, and VQ is the drop across the MOSFET when it is on. The following sections describe selection of components for a boost converter. 10138822 FIGURE 11. Simplified Boost Converter Diagram (a) First cycle of operation. (b) Second cycle of operation POWER INDUCTOR SELECTION The inductor is one of the two energy storage elements in a boost converter. Figure 12 shows how the inductor current varies during a switching cycle. The current through an inductor is quantified as: www.national.com 14 LM3488/LM3488Q 10138824 FIGURE 12. A. Inductor Current B. Diode Current If VL(t) is constant, diL(t)/dt must be constant. Hence, for a given input voltage and output voltage, the current in the inductor changes at a constant rate. The important quantities in determining a proper inductance value are IL (the average inductor current) and iL (the inductor current ripple). If iL is larger than IL, the inductor current will drop to zero for a portion of the cycle and the converter 15 www.national.com LM3488/LM3488Q will operate in discontinuous conduction mode. If iL is smaller than IL, the inductor current will stay above zero and the converter will operate in continuous conduction mode. All the analysis in this datasheet assumes operation in continuous conduction mode. To operate in continuous conduction mode, the following conditions must be met: A core size with ratings higher than these values should be chosen. If the core is not properly rated, saturation will dramatically reduce overall efficiency. The LM3488 can be set to switch at very high frequencies. When the switching frequency is high, the converter can be operated with very small inductor values. With a small inductor value, the peak inductor current can be extremely higher than the output currents, especially under light load conditions. The LM3488 senses the peak current through the switch. The peak current through the switch is the same as the peak current calculated above. IL > iL PROGRAMMING THE OUTPUT VOLTAGE The output voltage can be programmed using a resistor divider between the output and the feedback pins, as shown in Figure 13. The resistors are selected such that the voltage at the feedback pin is 1.26V. RF1 and RF2 can be selected using the equation, Choose the minimum IOUT to determine the minimum L. A common choice is to set iL to 30% of IL. Choosing an appropriate core size for the inductor involves calculating the average and peak currents expected through the inductor. In a boost converter, A 100pF capacitor may be connected between the feedback and ground pins to reduce noise. and IL_peak = IL(max) + iL(max), where 10138820 FIGURE 13. Adjusting the Output Voltage www.national.com 16 Where RSEN is the selected value based on current limit. With RSL installed, the control signal includes additional external slope to stabilize the loop, which will also have an effect on the current limit threshold. Therefore, the current limit threshold must be re-verified, as illustrated in the equations below : VCS = VSENSE - (D x (VSL + VSL)) Where VSL is the additional slope compensation generated and calculated as: VSL = 40 A x RSL RSEN x ISWLIMIT = VCSMAX = VSENSE - (D x VSL) Where ISWLIMIT is the peak switch current limit, defined by the equation below. As duty cycle increases, the control voltage is reduced as VSL ramps up. Since current limit threshold varies with duty cycle, the following equation should be used to select RSEN and set the desired current limit threshold: This changes the equation for current limit (or RSEN) to: The RSEN and RSL values may have to be calculated iteratively in order to achieve both the desired current limit and stable operation. In some designs RSL can also help to filter noise on the ISEN pin. If the inductor is selected such that ripple current is the recommended 30% value, and the current limit threshold is 120% of the maximum peak, a simpler method can be used to determine R SEN. The equation below will provide optimum stability without RSL, provided that the above 2 conditions are met: The numerator of the above equation is VCS, and ISWLIMIT is calculated as: To avoid false triggering, the current limit value should have some margin above the maximum operating value, typically 120%. Values for both VSENSE and VSL are specified in the characteristic table. However, calculating with the limits of these two specs could result in an unrealistically wide current limit or RSEN range. Therefore, the following equation is recommended, using the VSL ratio value given in the EC table: POWER DIODE SELECTION Observation of the boost converter circuit shows that the average current through the diode is the average load current, and the peak current through the diode is the peak current through the inductor. The diode should be rated to handle more than its peak current. The peak diode current can be calculated using the formula: RSEN is part of the current mode control loop and has some influence on control loop stability. Therefore, once the current limit threshold is set, loop stability must be verified. To verify stability, use the following equation: ID(Peak) = IOUT/ (1-D) + IL In the above equation, IOUT is the output current and IL has been defined in Figure 12 The peak reverse voltage for boost converter is equal to the regulator output voltage. The diode must be capable of handling this voltage. To improve efficiency, a low forward drop schottky diode is recommended. If the selected RSEN is greater than this value, additional slope compensation must be added to ensure stability, as described in the section below. POWER MOSFET SELECTION The drive pin of LM3488 must be connected to the gate of an external MOSFET. In a boost topology, the drain of the external N-Channel MOSFET is connected to the inductor and the source is connected to the ground. The drive pin (DR) voltage depends on the input voltage (see typical performance characteristics). In most applications, a logic level MOSFET can be used. For very low input voltages, a sublogic level MOSFET should be used. The selected MOSFET directly controls the efficiency. The critical parameters for selection of a MOSFET are: 1. Minimum threshold voltage, VTH(MIN) CURRENT LIMIT WITH EXTERNAL SLOPE COMPENSATION RSL is used to add additional slope compensation when required. It is not necessary in most designs and RSL should be no larger than necessary. Select RSL according to the following equation: 17 www.national.com LM3488/LM3488Q SETTING THE CURRENT LIMIT The maximum amount of current that can be delivered to the load is set by the sense resistor, RSEN. Current limit occurs when the voltage that is generated across the sense resistor equals the current sense threshold voltage, VSENSE. When this threshold is reached, the switch will be turned off until the next cycle. Limits for VSENSE are specified in the electrical characteristics section. VSENSE represents the maximum value of the internal control signal VCS. This control signal, however, is not a constant value and changes over the course of a period as a result of the internal compensation ramp (See Figure 3). Therefore the current limit threshold will also change. The actual current limit threshold is a function of the sense voltage (VSENSE) and the internal compensation ramp: LM3488/LM3488Q 2. On-resistance, RDS(ON) 3. Total gate charge, Qg 4. Reverse transfer capacitance, CRSS 5. Maximum drain to source voltage, VDS(MAX) The off-state voltage of the MOSFET is approximately equal to the output voltage. VDS(MAX) of the MOSFET must be greater than the output voltage. The power losses in the MOSFET can be categorized into conduction losses and ac switching or transition losses. RDS(ON) is needed to estimate the conduction losses. The conduction loss, PCOND, is the I2R loss across the MOSFET. The maximum conduction loss is given by: The input capacitor should be capable of handling the rms current. Although the input capacitor is not as critical in a boost application, low values can cause impedance interactions. Therefore a good quality capacitor should be chosen in the range of 10F to 20F. If a value lower than 10F is used, then problems with impedance interactions or switching noise can affect the LM3478. To improve performance, especially with VIN below 8 volts, it is recommended to use a 20 resistor at the input to provide a RC filter. The resistor is placed in series with the VIN pin with only a bypass capacitor attached to the VIN pin directly (see Figure 14). A 0.1F or 1F ceramic capacitor is necessary in this configuration. The bulk input capacitor and inductor will connect on the other side of the resistor with the input power supply. where DMAX is the maximum duty cycle. 10138893 FIGURE 14. Reducing IC Input Noise The turn-on and turn-off transitions of a MOSFET require times of tens of nano-seconds. CRSS and Qg are needed to estimate the large instantaneous power loss that occurs during these transitions. The amount of gate current required to turn the MOSFET on can be calculated using the formula: OUTPUT CAPACITOR SELECTION The output capacitor in a boost converter provides all the output current when the inductor is charging. As a result it sees very large ripple currents. The output capacitor should be capable of handling the maximum rms current. The rms current in the output capacitor is: IG = Qg.FS The required gate drive power to turn the MOSFET on is equal to the switching frequency times the energy required to deliver the charge to bring the gate charge voltage to VDR (see electrical characteristics and typical performance characteristics for the drive voltage specification). PDrive = FS.Qg.VDR Where INPUT CAPACITOR SELECTION Due to the presence of an inductor at the input of a boost converter, the input current waveform is continuous and triangular, as shown in Figure 12. The inductor ensures that the input capacitor sees fairly low ripple currents. However, as the input capacitor gets smaller, the input ripple goes up. The rms current in the input capacitor is given by: and D, the duty cycle is equal to (VOUT - VIN)/VOUT. The ESR and ESL of the output capacitor directly control the output ripple. Use capacitors with low ESR and ESL at the output for high efficiency and low ripple voltage. Surface Mount tantalums, surface mount polymer electrolytic and polymer tantalum, Sanyo- OSCON, or multi-layer ceramic capacitors are recommended at the output. Due to the presence of the inductor L1 at the input, the SEPIC inherits all the benefits of a boost converter. One main advantage of SEPIC over boost converter is the inherent input to output isolation. The capacitor CS isolates the input from the output and provides protection against shorted or malfunctioning load. Hence, the A SEPIC is useful for replacing boost circuits when true shutdown is required. This means that the output voltage falls to 0V when the switch is turned off. In a boost converter, the output can only fall to the input voltage minus a diode drop. The duty cycle of a SEPIC is given by: Designing SEPIC Using LM3488 Since the LM3488 controls a low-side N-Channel MOSFET, it can also be used in SEPIC (Single Ended Primary Inductance Converter) applications. An example of SEPIC using LM3488 is shown in Figure 15. As shown in Figure 15, the output voltage can be higher or lower than the input voltage. The SEPIC uses two inductors to step-up or step-down the input voltage. The inductors L1 and L2 can be two discrete inductors or two windings of a coupled transformer since equal voltages are applied across the inductor throughout the switching cycle. Using two discrete inductors allows use of catalog magnetics, as opposed to a custom transformer. The input ripple can be reduced along with size by using the coupled windings of transformer for L1 and L2. www.national.com 18 LM3488/LM3488Q In the above equation, VQ is the on-state voltage of the MOSFET, Q, and VDIODE is the forward voltage drop of the diode. 10138844 FIGURE 15. Typical SEPIC Converter POWER MOSFET SELECTION As in boost converter, the parameters governing the selection of the MOSFET are the minimum threshold voltage, VTH (MIN), the on-resistance, RDS(ON), the total gate charge, Qg, the reverse transfer capacitance, CRSS, and the maximum drain to source voltage, VDS(MAX). The peak switch voltage in a SEPIC is given by: IL2AVE = IOUT Peak to peak ripple current, to calculate core loss if necessary: VSW(PEAK) = VIN + VOUT + VDIODE The selected MOSFET should satisfy the condition: VDS(MAX) > VSW(PEAK) The peak switch current is given by: The rms current through the switch is given by: maintains the condition IL > iL/2 to ensure constant current mode. POWER DIODE SELECTION The Power diode must be selected to handle the peak current and the peak reverse voltage. In a SEPIC, the diode peak current is the same as the switch peak current. The off-state voltage or peak reverse voltage of the diode is VIN + VOUT. Similar to the boost converter, the average diode current is equal to the output current. Schottky diodes are recommended. Peak current in the inductor, to ensure the inductor does not saturate: SELECTION OF INDUCTORS L1 AND L2 Proper selection of the inductors L1 and L2 to maintain constant current mode requires calculations of the following parameters. Average current in the inductors: 19 www.national.com LM3488/LM3488Q There is an energy balance between CS and L1, which can be used to determine the value of the capacitor. The basic energy balance equation is: IL1PK must be lower than the maximum current rating set by the current sense resistor. The value of L1 can be increased above the minimum recommended to reduce input ripple and output ripple. However, once DIL1 is less than 20% of IL1AVE, the benefit to output ripple is minimal. By increasing the value of L2 above the minimum recommended, IL2 can be reduced, which in turn will reduce the output ripple voltage: Where is the ripple voltage across the SEPIC capacitor, and where ESR is the effective series resistance of the output capacitor. If L1 and L2 are wound on the same core, then L1 = L2 = L. All the equations above will hold true if the inductance is replaced by 2L. A good choice for transformer with equal turns is Coiltronics CTX series Octopack. is the ripple current through the inductor L1. The energy balance equation can be solved to provide a minimum value for CS: SENSE RESISTOR SELECTION The peak current through the switch, ISW(PEAK) can be adjusted using the current sense resistor, RSEN, to provide a certain output current. Resistor RSEN can be selected using the formula: Input Capacitor Selection Sepic Capacitor Selection Similar to a boost converter, the SEPIC has an inductor at the input. Hence, the input current waveform is continuous and triangular. The inductor ensures that the input capacitor sees fairly low ripple currents. However, as the input capacitor gets smaller, the input ripple goes up. The rms current in the input capacitor is given by: The selection of SEPIC capacitor, CS, depends on the rms current. The rms current of the SEPIC capacitor is given by: The input capacitor should be capable of handling the rms current. Although the input capacitor is not as critical in a boost application, low values can cause impedance interactions. Therefore a good quality capacitor should be chosen in the range of 10F to 20F. If a value lower than 10F is used, then problems with impedance interactions or switching noise can affect the LM3478. To improve performance, especially with VIN below 8 volts, it is recommended to use a 20 resistor at the input to provide a RC filter. The resistor is placed in series with the VIN pin with only a bypass capacitor attached to the VIN pin directly (see Figure 14). A 0.1F or 1F ceramic capacitor is necessary in this configuration. The bulk input capacitor and inductor will connect on the other side of the resistor with the input power supply. The SEPIC capacitor must be rated for a large ACrms current relative to the output power. This property makes the SEPIC much better suited to lower power applications where the rms current through the capacitor is relatively small (relative to capacitor technology). The voltage rating of the SEPIC capacitor must be greater than the maximum input voltage. Tantalum capacitors are the best choice for SMT, having high rms current ratings relative to size. Ceramic capacitors could be used, but the low C values will tend to cause larger changes in voltage across the capacitor due to the large currents. High C value ceramics are expensive. Electrolytics work well for through hole applications where the size required to meet the rms current rating can be accommodated. www.national.com 20 The ESR and ESL of the output capacitor directly control the output ripple. Use low capacitors with low ESR and ESL at the output for high efficiency and low ripple voltage. Surface mount tantalums, surface mount polymer electrolytic and polymer tantalum, Sanyo- OSCON, or multi-layer ceramic capacitors are recommended at the output. The output capacitor of the SEPIC sees very large ripple currents (similar to the output capacitor of a boost converter. The rms current through the output capacitor is given by: The ESR and ESL of the output capacitor directly control the output ripple. Use low capacitors with low ESR and ESL at the output for high efficiency and low ripple voltage. Surface mount tantalums, surface mount polymer electrolytic and polymer tantalum, Sanyo- OSCON, or multi-layer ceramic capacitors are recommended at the output for low ripple. Other Application Circuits 10138843 FIGURE 16. Typical High Efficiency Step-Up (Boost) Converter 21 www.national.com LM3488/LM3488Q Output Capacitor Selection LM3488/LM3488Q Physical Dimensions inches (millimeters) unless otherwise noted www.national.com 22 LM3488/LM3488Q Notes 23 www.national.com LM3488/LM3488Q High Efficiency Low-Side N-Channel Controller for Switching Regulators Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: www.national.com Products Design Support Amplifiers www.national.com/amplifiers WEBENCH(R) Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage References www.national.com/vref Design Made Easy www.national.com/easy www.national.com/powerwise Applications & Markets www.national.com/solutions Mil/Aero www.national.com/milaero PowerWise(R) Solutions Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors SolarMagicTM www.national.com/solarmagic PLL/VCO www.national.com/wireless www.national.com/training PowerWise(R) Design University THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2011 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated