MU SC FC Harsh
Environment Attenuators Terminators
55
Harsh Environment Fiber Optic Connectors
MF 14 and MF 17 Series
■Features
1.
2 Fibers (MF14 series), 4 Fibers (MF17 series), or Optical/Electrical Hybrids are available.
6 fibers (MF22 series) available.
2. Incorrect Insertion Prevention.
Guide key (plug) and key slot (receptacle) are designed for prevent incorrect insertion.
3. Plug, receptacle fully mated condition satisfy IP67 wateroof Performance.
4. For more than 10 years, MF series has been designed and installed in many harsh
environmental applications.
Please contact us if you have any requests.
HIROSE will offer excellent solutions to meet your requirements.
■Applications
Outdoor optical transmission systems, LAN, CATV, ATM, Base station, industrial optical/electric lines.
56
MUSCFC
Harsh
Environment
AttenuatorsTerminators
Optical
characteristics
Mechanical
characteristics
Environmental
characteristics
Part Material
Plug and Receptacle Housing Aluminum alloy
Ferrule case Synthetic resin
Strain relief Zinc alloy
Protective cap and clamp Brass
Rubber boot and O-rings Synthetic rubber
Screws, springs, and steel wire Stainless steel
Washer Brass
Split sleeve Zirconia or Copper alloy
■Product Specifications
Ratings Operating temperature range
Note: Insertion loss herein means only connection loss.
-25°C to +70°C Storage temperature range -25°C to +70°C
■Materials
Item Test Method Specifications
Insertion Loss Wavelength 1310nm (LD) 1.0dB max. (Note)
Durability 100 times
(cycles, mating/un-mating)
Vibration
Shock
Humidity
-10°C to 65°C, humidity: 90% to 96%
10 cycles
(Temperature/ humidity- cycles)
Change of temperature -40
°C
to +75
°C 42 cycles
Dry heat 960 hours at 85°C
Cold 960 hours at -40°C
Salt Mist 1000 hours in a 5% concentration of salt mist No visible corrosion.
Waterproof Inside air pressure 4.90kPa for one minute No air bubble leakege, IP67
Frequency: 10 to 55 Hz, single amplitude of 0.75 mm,
acceleration of 98.1m/s
2
, 2 hours in each of the 2 axis.
Acceleration of 981 m/s
2
, 6 ms duration, sine half-
wave waveform, 3 cycles in each of the 2 axis.
1)
Insertion loss fluctuation after test: 0.3dB max.
2)
No visible damage, dislocation of clamp or cable.
1)
Insertion loss fluctuation after (test) : 0.3dB max.
2)
No visible damage, dislocation of clamp or cable.
■Important Notice
1. Please ask HIROSE when you assemble the MF connectors for special cables.
Some cables can not be used for the connectors.
2. MF series use SC/PC zirconia ferrules. Please see page 33.
57
MU SC FC Harsh
Environment Attenuators Terminators
* indicates cable diameter. 8, 9 and 10mm, diameter cables are appicable.
■Bayonet lock
●Plug Housing
ØA
ØD
E
BC
Number of Fibers ØAB C ØDE
2
4
24
27
184.7
116.5
69
52
24
27
21
21
Part Number
MF14B-WP*S01-0200
MF17B-WP*S01-0400
Note: Up to 3 mm cables are applicable.
●Square Flange Receptacle Housing
ØF
G
Ø D
4- Ø3.3
M E
A
C
B3
Number of Fibers MAB C ØDMEØFG
2
4
30
35
10
10
45.5
51.5
20.5
25.5
23
27
24
27
18.7
18.7
Part Number
MF14B-WRF01-0200
MF17B-WRF01-0400
Note: Up to 3 mm cables are applicable.
●Bulk Head Receptacle Housing
ØD
ØF
G
A
C
B3
E HEX
Number of Fibers MAB C ØDMEØFG
2
4
30
34
17.5
17.5
45.5
51.5
20.5
25.5
28
32
24
27
18.7
18.7
Part Number
MF14B-WRB01-0200
MF17B-WRB01-0400
58
MUSCFC
Harsh
Environment
AttenuatorsTerminators
■Threaded lock
●Plug housing
ØD
E
ØA
B C
F
Note: Up to 3 mm cables are applicable.
●Square Flange Receptacle Housing
H
ØD
ØG±0.3
4- Ø3.3
E
MF
M A
B3
C
Part Number MAB C ØDEMFØGH
2
4
30
35
10
10
45.5
51.5
20.5
25.5
M20∞1
M22∞1
23
27
24
27
18.5
18.5
Part Number
MF14S-WRF01-0200
MF17S-WRF01-0400
Note: Up to 3 mm cables are applicable.
●Bulk Head Receptacle Housing
H
ØD
ØG
E
A
C
B3
F HEX
Part Number MAB C ØDEMFØGH
2
4
31
34
17.5
17.5
45.5
51.5
20.5
25.5
M20∞1
M22∞1
30
32
24
27
18.5
18.5
Part Number
MF14S-WRB01-0200
MF17S-WRB01-0400
*indicates the cable diameter. 8, 9 and 10mm, diameter cables are applicable.
Number of Fibers ØAB C ØDE F
2
4
24
27
184.7
116.5
69
52
24
27
20.8
20.8
M20∞1
M22∞1
Part Number
MF14S-WP*S01-0200
MF17S-WP*S01-0400
59
MU SC FC Harsh
Environment Attenuators Terminators
BPanel cut-out
●Square Flange Receptacle
ØA
MB
4- Ø3.3
B
ØA
●Bulk Head Receptacle
AB
21
21
26
26
23
23
27
27
Part Number
MF14B-WRF01-0200
MF14S-WRF01-0200
MF17B-WRF01-0400
MF17S-WRF01-0400
AB
22.2
24.2
24.2
24.2
21.2
23.2
23.2
23.2
Part Number
MF14B-WRB01-0200
MF14S-WRB01-0200
MF17B-WRB01-0400
MF17S-WRB01-0400
Panel thickness: 2mm to 4.5mm
Panel thickness: 2mm to 4.5mm
MU SC FC Harsh
Environment Attenuators Terminators
61
Harsh Environment Fiber Optic Connector
MF22 Series
Receptacles
Plugs
■Features
1. 6 Fibers or Optical /Electric Hybrids are
available
2 fibers (MF14), 4fibers (MF17) available.
Please contact us if you have any requests.
HIROSE will offer excellent solutions to meet your requirements.
2. Incorrect Insertion Prevention
Five guide keys positioned at specific angles assure that the
connector will mate only with the corresponding assembly.
3.
Plug, receptacle fully mated condition satisfy
IP67 waterproof performance.
4. Harsh environment applications
The connector’s outer surfaces are covered with heat
baked hard coating and all internal connections are
protected by seals.
5. Cable Termination
The connector will terminate with a majority of cables having
outside diameter from 7mm to 12mm.
Please contact Hirose for other applicable cable.
■Applications
Outdoor optical transmission systems, LAN, CATV, ATM,
and other applications requiring environmentally protected
optical or electrical connections.
Insertion Loss Wavelength 850nm (LD) 0.7dB max. (Note)
Durability 500 times
(cycles, mating/un-mating)
Vibration
Shock
Humidity -10°C to 65°C, humidity: 90% to 96% 10 cycles
(Temperature/ humidity- cycles)
Change of temperatice -40
°C
/+75
°C 42 cycles
Dry heat 336 hours at 85°C
Cold 240 hours at -40°C
Salt mist 1000 hours in a 5% concentration of salt mist No visible corrosion.
Waterproof Inside air pressure 4.90kPa for one minute No air bubble leakege, IP67
62
MUSCFC
Harsh
Environment
AttenuatorsTerminators
Optical
characteristics
Mechanical
characteristics
Environmental
characteristics
Part Material
Plug and Receptacle Housing Aluminum alloy
Ferrule case Synthetic resin
Strain relief components Zinc alloy
Protective cap and clamp Synthetic resin
Rubber boot and O-rings Synthetic rubber
Screws, springs, and ball chain Stainless steel
Washer Brass
Split sleeve Zirconia or Copper alloy
■Product Specifications
Ratings Operating temperature range
Note: Insertion loss herein means only connection loss.
-40°C to +75°C Storage temperature range -40°C to +85°C
■Materials
Item Test Method Specifications
Frequency: 10 to 55 Hz, single amplitude of 0.75 mm,
acceleration of 98.1m/s
2
, 2 hours in each of the 2 axis.
Acceleration of 981 m/s
2
, 6 ms duration, sine half-
wave waveform, 3 cycles in each of the 2 axis.
1)
Insertion loss fluctuation after test: 0.3dB max.
2)
No visible damage, dislocation of clamp or cable.
1)
Insertion loss fluctuation (after test): 0.3dB max.
2)
No visible damage, dislocation of clamp or cable.
■Important Notice
1. Please ask HIROSE when you assemble the MF connectors for special cables.
Some cables can not be used for the connectors.
2. MF series use SC/PC zirconia ferrules. Please see page 33.
63
MU SC FC Harsh
Environment Attenuators Terminators
*indicates cable diameter.
●Plug housing
121
126
Tr30∞2
Ø34
6
5
4
1
2
3
Ø32
Tr30∞2
43
42 HEX
43
Ø45
32.35
20
33+0.5
0
Ø34
+0.5
0
■Threaded lock
Part Number Number of Fibers
MF22S-WDP*S01-0600 6
Note: Up to 3 mm cables are applicable.
●Bulk head receptacle housing
Part Number Number of Fibers
MF22S-WDRB01-0600 6
BPanel cut-out
Panel thickness: 1mm to 4mm
64
MUSCFC
Harsh
Environment
AttenuatorsTerminators
●Plug assembly tool
■Tools
Part Number CL No.
MF22S-T2 709-0065-0
Part Number CL No.
HSC-T3 704-0287-0
●Crimp tool for receptacle assembly