ATTINY2313V-10MI - Atmel - Datasheet.Support

2543ES–AVR–04/04

Features

•Utilizes the AVR® RISC Architecture

•AVR – High-performance and Low-power RISC Architecture

– 120 Powerful Instructions – Most Single Clock Cycle Execution

– 32 x 8 General Purpose Working Registers

– Fully Static Operation

– Up to 20 MIPS Throughput at 20 MHz

•Data and Non-volatile Program and Data Memories

– 2K Bytes of In-System Self Programmable Flash

Endurance 10,000 Write/Erase Cycles

– 128 Bytes In-System Programmable EEPROM

Endurance: 100,000 Write/Erase Cycles

– 128 Bytes Internal SRAM

– Programming Lock for Flash Program and EEPROM Data Security

•Peripheral Features

– One 8-bit Timer/Counter with Separate Prescaler and Compare Mode

– One 16-bit Timer/Counter with Separate Prescaler, Compare and Capture Modes

– Four PWM Channels

– On-chip Analog Comparator

– Programmable Watchdog Timer with On-chip Oscillator

– USI – Universal Serial Interface

– Full Duplex USART

•Special Microcontroller Features

– debugWIRE On-chip Debugging

– In-System Programmable via SPI Port

– External and Internal Interrupt Sources

– Low-power Idle, Power-down, and Standby Modes

– Enhanced Power-on Reset Circuit

– Programmable Brown-out Detection Circuit

– Internal Calibrated Oscillator

•I/O and Packages

– 18 Programmable I/O Lines

– 20-pin PDIP, 20-pin SOIC, and 32-pin MLF

•Operating Voltages

– 1.8 - 5.5V (ATtiny2313)

•Speed Grades

– ATtiny2313V: 0 - 4 MHz @ 1.8 - 5.5V, 0 - 10 MHz @ 2.7 - 5.5V

– ATtiny2313: 0 - 10 MHz @ 2.7 - 5.5V, 0 - 20 MHz @ 4.5 - 5.5V

•Power Consumption Estimates

– Active Mode

1 MHz, 1.8V: 300 µA

32 kHz, 1.8V: 20 µA (including oscillator)

– Power-down Mode

< 0.2 µA at 1.8V

8-bit

Microcontroller

with 2K Bytes

In-System

Programmable

Flash

ATtiny2313/V

Preliminary

Summary

Rev. 2543ES–AVR–04/04

Note: This is a summary document. A complete document

is available on our Web site at www.atmel.com.

2ATtiny2313/V

2543ES–AVR–04/04

Pin Configurations Figure 1. Pinout ATtiny2313

Overview The ATtiny2313 is a low-power CMOS 8-bit microcontroller based on the AVR

enhanced RISC architecture. By executing powerful instructions in a single clock cycle,

the ATtiny2313 achieves throughputs approaching 1 MIPS per MHz allowing the system

designer to optimize power consumption versus processing speed.

(RESET/dW)PA2

(RXD)PD0

(TXD)PD1

(XTAL2)PA1

(XTAL1)PA0

(CKOUT/XCK/INT0)PD2

(INT1)PD3

(T0)PD4

(OC0B/T1)PD5

GND

VCC

PB7(UCSK/SCK/PCINT7)

PB6(MISO/DO/PCINT6)

PB5(MOSI/DI/SDA/PCINT5)

PB4(OC1B/PCINT4)

PB3(OC1A/PCINT3)

PB2(OC0A/PCINT2)

PB1(AIN1/PCINT1)

PB0(AIN0/PCINT0)

PD6(ICP)

PDIP/SOIC

ATtiny2313/V

2543ES–AVR–04/04

Block Diagram

Figure 2. Block Diagram

PROGRAM

COUNTER

PROGRAM

FLASH

INSTRUCTION

GND

VCC

INSTRUCTION

DECODER

CONTROL

LINES

STACK

POINTER

SRAM

GENERAL

PURPOSE

ALU

STATUS

PROGRAMMING

LOGIC SPI

8-BIT DATA BUS

XTAL1 XTAL2

RESET

INTERNAL

OSCILLATOR

WATCHDOG

TIMER

TIMING AND

CONTROL

MCU CONTROL

MCU STATUS

TIMER/

COUNTERS

INTERRUPT

UNIT

EEPROM

USI

USART

ANALOG

COMPARATOR

DATA REGISTER

PORTB

DATA DIR.

REG. PORTB

DATA REGISTER

PORTA

DATA DIR.

REG. PORTA

PORTB DRIVERS

PB0 - PB7

PORTA DRIVERS

PA0 - PA2

DATA REGISTER

PORTD

DATA DIR.

REG. PORTD

PORTD DRIVERS

PD0 - PD6

ON-CHIP

DEBUGGER

INTERNAL

CALIBRATED

OSCILLATOR

4ATtiny2313/V

2543ES–AVR–04/04

The AVR core combines a rich instruction set with 32 general purpose working registers.

All the 32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing

two independent registers to be accessed in one single instruction executed in one clock

cycle. The resulting architecture is more code efficient while achieving throughputs up to

ten times faster than conventional CISC microcontrollers.

The ATtiny2313 provides the following features: 2K bytes of In-System Programmable

Flash, 128 bytes EEPROM, 128 bytes SRAM, 18 general purpose I/O lines, 32 general

purpose working registers, a single-wire Interface for On-chip Debugging, two flexible

Timer/Counters with compare modes, internal and external interrupts, a serial program-

mable USART, Universal Serial Interface with Start Condition Detector, a programmable

Watchdog Timer with internal Oscillator, and three software selectable power saving

modes. The Idle mode stops the CPU while allowing the SRAM, Timer/Counters, and

interrupt system to continue functioning. The Power-down mode saves the register con-

tents but freezes the Oscillator, disabling all other chip functions until the next interrupt

or hardware reset. In Standby mode, the crystal/resonator Oscillator is running while the

rest of the device is sleeping. This allows very fast start-up combined with low-power

consumption.

The device is manufactured using Atmel’s high density non-volatile memory technology.

The On-chip ISP Flash allows the program memory to be reprogrammed In-System

through an SPI serial interface, or by a conventional non-volatile memory programmer.

By combining an 8-bit RISC CPU with In-System Self-Programmable Flash on a mono-

lithic chip, the Atmel ATtiny2313 is a powerful microcontroller that provides a highly

flexible and cost effective solution to many embedded control applications.

The ATtiny2313 AVR is supported with a full suite of program and system development

tools including: C Compilers, Macro Assemblers, Program Debugger/Simulators, In-Cir-

cuit Emulators, and Evaluation kits.

ATtiny2313/V

2543ES–AVR–04/04

Pin Descriptions

VCC Digital supply voltage.

GND Ground.

Port A (PA2..PA0) Port A is a 3-bit bi-directional I/O port with internal pull-up resistors (selected for each

bit). The Port A output buffers have symmetrical drive characteristics with both high sink

and source capability. As inputs, Port A pins that are externally pulled low will source

current if the pull-up resistors are activated. The Port A pins are tri-stated when a reset

condition becomes active, even if the clock is not running.

Port A also serves the functions of various special features of the ATtiny2313 as listed

on page 52.

Port B (PB7..PB0) Port B is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each

bit). The Port B output buffers have symmetrical drive characteristics with both high sink

and source capability. As inputs, Port B pins that are externally pulled low will source

current if the pull-up resistors are activated. The Port B pins are tri-stated when a reset

condition becomes active, even if the clock is not running.

Port B also serves the functions of various special features of the ATtiny2313 as listed

on page 52.

Port D (PD6..PD0) Port D is a 7-bit bi-directional I/O port with internal pull-up resistors (selected for each

bit). The Port D output buffers have symmetrical drive characteristics with both high sink

and source capability. As inputs, Port D pins that are externally pulled low will source

current if the pull-up resistors are activated. The Port D pins are tri-stated when a reset

condition becomes active, even if the clock is not running.

Port D also serves the functions of various special features of the ATtiny2313 as listed

on page 55.

RESET Reset input. A low level on this pin for longer than the minimum pulse length will gener-

ate a reset, even if the clock is not running. The minimum pulse length is given in Table

15 on page 33. Shorter pulses are not guaranteed to generate a reset. The Reset Input

is an alternate function for PA2 and dW.

XTAL1 Input to the inverting Oscillator amplifier and input to the internal clock operating circuit.

XTAL1 is an alternate function for PA0.

XTAL2 Output from the inverting Oscillator amplifier. XTAL2 is an alternate function for PA1.

6ATtiny2313/V

2543ES–AVR–04/04

Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Page

0x3F (0x5F) SREG I T H S V N Z C 7

0x3E (0x5E) Reserved – – – – – – – –

0x3D (0x5D) SPL SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 10

0x3C (0x5C) OCR0B Timer/Counter0 – Compare Register B 76

0x3B (0x5B) GIMSK INT1 INT0 PCIE – – – – –59

0x3A (0x5A) EIFR INTF1 INTF0 PCIF – – – – –60

0x39 (0x59) TIMSK TOIE1 OCIE1A OCIE1B – ICIE1 OCIE0B TOIE0 OCIE0A 77, 108

0x38 (0x58) TIFR TOV1 OCF1A OCF1B – ICF1 OCF0B TOV0 OCF0A 77

0x37 (0x57) SPMCSR ––– CTPB RFLB PGWRT PGERS SELFPRGEN 154

0x36 (0x56) OCR0A Timer/Counter0 – Compare Register A 76

0x35 (0x55) MCUCR PUD SM1 SE SM0 ISC11 ISC10 ISC01 ISC00 52

0x34 (0x54) MCUSR –––– WDRF BORF EXTRF PORF 36

0x33 (0x53) TCCR0B FOC0A FOC0B –– WGM02 CS02 CS01 CS00 75

0x32 (0x52) TCNT0 Timer/Counter0 (8-bit) 76

0x31 (0x51) OSCCAL – CAL6 CAL5 CAL4 CAL3 CAL2 CAL1 CAL0 25

0x30 (0x50) TCCR0A COM0A1 COM0A0 COM0B1 COM0B0 ––WGM01WGM00 72

0x2F (0x4F) TCCR1A COM1A1 COM1A0 COM1B1 COM1BO –– WGM11 WGM10 103

0x2E (0x4E) TCCR1B ICNC1 ICES1 – WGM13 WGM12 CS12 CS11 CS10 106

0x2D (0x4D) TCNT1H Timer/Counter1 – Counter Register High Byte 107

0x2C (0x4C) TCNT1L Timer/Counter1 – Counter Register Low Byte 107

0x2B (0x4B) OCR1AH Timer/Counter1 – Compare Register A High Byte 107

0x2A (0x4A) OCR1AL Timer/Counter1 – Compare Register A Low Byte 107

0x29 (0x49) OCR1BH Timer/Counter1 – Compare Register B High Byte 108

0x28 (0x48) OCR1BL Timer/Counter1 – Compare Register B Low Byte 108

0x27 (0x47) Reserved – – – – – – – –

0x26 (0x46) CLKPR CLKPCE ––– CLKPS3 CLKPS2 CLKPS1 CLKPS0 27

0x25 (0x45) ICR1H Timer/Counter1 - Input Capture Register High Byte 108

0x24 (0x44) ICR1L Timer/Counter1 - Input Capture Register Low Byte 108

0x23 (0x43) GTCCR – – – – – – – PSR10 80

0x22 (ox42) TCCR1C FOC1A FOC1B – – – – – – 107

0x21 (0x41) WDTCSR WDIF WDIE WDP3 WDCE WDE WDP2 WDP1 WDP0 41

0x20 (0x40) PCMSK PCINT7 PCINT6 PCINT5 PCINT4 PCINT3 PCINT2 PCINT1 PCINT0 60

0x1F (0x3F) Reserved – – – – – – – –

0x1E (0x3E) EEAR – EEPROM Address Register 15

0x1D (0x3D) EEDR EEPROM Data Register 16

0x1C (0x3C) EECR –– EEPM1 EEPM0 EERIE EEMPE EEPE EERE 16

0x1B (0x3B) PORTA – – – – – PORTR2 PORTA1 PORTA0 57

0x1A (0x3A) DDRA – – – – – DDA2 DDA1 DDA0 57

0x19 (0x39) PINA – – – – – PINA2 PINA1 PINA0 57

0x18 (0x38) PORTB PORTB7 PORTB6 PORTB5 PORTB4 PORTB3 PORTB2 PORTB1 PORTB0 57

0x17 (0x37) DDRB DDB7 DDB6 DDB5 DDB4 DDB3 DDB2 DDB1 DDB0 57

0x16 (0x36) PINB PINB7 PINB6 PINB5 PINB4 PINB3 PINB2 PINB1 PINB0 57

0x15 (0x35) GPIOR2 General Purpose I/O Register 2 20

0x14 (0x34) GPIOR1 General Purpose I/O Register 1 20

0x13 (0x33) GPIOR0 General Purpose I/O Register 0 20

0x12 (0x32) PORTD – PORTD6 PORTD5 PORTD4 PORTD3 PORTD2 PORTD1 PORTD0 57

0x11 (0x31) DDRD – DDD6 DDD5 DDD4 DDD3 DDD2 DDD1 DDD0 57

0x10 (0x30) PIND – PIND6 PIND5 PIND4 PIND3 PIND2 PIND1 PIND0 57

0x0F (0x2F) USIDR USI Data Register 143

0x0E (0x2E) USISR USISIF USIOIF USIPF USIDC USICNT3 USICNT2 USICNT1 USICNT0 144

0x0D (0x2D) USICR USISIE USIOIE USIWM1 USIWM0 USICS1 USICS0 USICLK USITC 145

0x0C (0x2C) UDR UART Data Register (8-bit) 128

0x0B (0x2B) UCSRA RXC TXC UDRE FE DOR UPE U2X MPCM 128

0x0A (0x2A) UCSRB RXCIE TXCIE UDRIE RXEN TXEN UCSZ2 RXB8 TXB8 130

0x09 (0x29) UBRRL UBRRH[7:0] 132

0x08 (0x28) ACSR ACD ACBG ACO ACI ACIE ACIC ACIS1 ACIS0 148

0x07 (0x27) Reserved – – – – – – – –

0x06 (0x26) Reserved – – – – – – – –

0x05 (0x25) Reserved – – – – – – – –

0x04 (0x24) Reserved – – – – – – – –

0x03 (0x23) UCSRC – UMSEL UPM1 UPM0 USBS UCSZ1 UCSZ0 UCPOL 131

0x02 (0x22) UBRRH – – – – UBRRH[11:8] 132

0x01 (0x21) DIDR – – – – – – AIN1D AIN0D 149

0x00 (0x20) Reserved – – – – – – – –

ATtiny2313/V

2543ES–AVR–04/04

Note: 1. For compatibility with future devices, reserved bits should be written to zero if accessed. Reserved I/O memory addresses

should never be written.

2. I/O Registers within the address range 0x00 - 0x1F are directly bit-accessible using the SBI and CBI instructions. In these

registers, the value of single bits can be checked by using the SBIS and SBIC instructions.

3. Some of the status flags are cleared by writing a logical one to them. Note that, unlike most other AVRs, the CBI and SBI

instructions will only operate on the specified bit, and can therefore be used on registers containing such status flags. The

CBI and SBI instructions work with registers 0x00 to 0x1F only.

4. When using the I/O specific commands IN and OUT, the I/O addresses 0x00 - 0x3F must be used. When addressing I/O

Registers as data space using LD and ST instructions, 0x20 must be added to these addresses.

8ATtiny2313/V

2543ES–AVR–04/04

Instruction Set Summary

Mnemonics Operands Description Operation Flags #Clocks

ARITHMETIC AND LOGIC INSTRUCTIONS

ADD Rd, Rr Add two Registers Rd ← Rd + Rr Z,C,N,V,H 1

ADC Rd, Rr Add with Carry two Registers Rd ← Rd + Rr + C Z,C,N,V,H 1

ADIW Rdl,K Add Immediate to Word Rdh:Rdl ← Rdh:Rdl + K Z,C,N,V,S 2

SUB Rd, Rr Subtract two Registers Rd ← Rd - Rr Z,C,N,V,H 1

SUBI Rd, K Subtract Constant from Register Rd ← Rd - K Z,C,N,V,H 1

SBC Rd, Rr Subtract with Carry two Registers Rd ← Rd - Rr - C Z,C,N,V,H 1

SBCI Rd, K Subtract with Carry Constant from Reg. Rd ← Rd - K - C Z,C,N,V,H 1

SBIW Rdl,K Subtract Immediate from Word Rdh:Rdl ← Rdh:Rdl - K Z,C,N,V,S 2

AND Rd, Rr Logical AND Registers Rd ← Rd • Rr Z,N,V 1

ANDI Rd, K Logical AND Register and Constant Rd ← Rd • K Z,N,V 1

OR Rd, Rr Logical OR Registers Rd ← Rd v Rr Z,N,V 1

ORI Rd, K Logical OR Register and Constant Rd ← Rd v K Z,N,V 1

EOR Rd, Rr Exclusive OR Registers Rd ← Rd ⊕ Rr Z,N,V 1

COM Rd One’s Complement Rd ← 0xFF − Rd Z,C,N,V 1

NEG Rd Two’s Complement Rd ← 0x00 − Rd Z,C,N,V,H 1

SBR Rd,K Set Bit(s) in Register Rd ← Rd v K Z,N,V 1

CBR Rd,K Clear Bit(s) in Register Rd ← Rd • (0xFF - K) Z,N,V 1

INC Rd Increment Rd ← Rd + 1 Z,N,V 1

DEC Rd Decrement Rd ← Rd − 1 Z,N,V 1

TST Rd Test for Zero or Minus Rd ← Rd • Rd Z,N,V 1

CLR Rd Clear Register Rd ← Rd ⊕ Rd Z,N,V 1

SER Rd Set Register Rd ← 0xFF None 1

BRANCH INSTRUCTIONS

RJMP k Relative Jump PC ← PC + k + 1 None 2

IJMP Indirect Jump to (Z) PC ← Z None 2

RCALL k Relative Subroutine Call PC ← PC + k + 1 None 3

ICALL Indirect Call to (Z) PC ← ZNone3

RET Subroutine Return PC ← STACK None 4

RETI Interrupt Return PC ← STACK I 4

CPSE Rd,Rr Compare, Skip if Equal if (Rd = Rr) PC ← PC + 2 or 3 None 1/2/3

CP Rd,Rr Compare Rd − Rr Z, N,V,C,H 1

CPC Rd,Rr Compare with Carry Rd − Rr − C Z, N,V,C,H 1

CPI Rd,K Compare Register with Immediate Rd − K Z, N,V,C,H 1

SBRC Rr, b Skip if Bit in Register Cleared if (Rr(b)=0) PC ← PC + 2 or 3 None 1/2/3

SBRS Rr, b Skip if Bit in Register is Set if (Rr(b)=1) PC ← PC + 2 or 3 None 1/2/3

SBIC P, b Skip if Bit in I/O Register Cleared if (P(b)=0) PC ← PC + 2 or 3 None 1/2/3

SBIS P, b Skip if Bit in I/O Register is Set if (P(b)=1) PC ← PC + 2 or 3 None 1/2/3

BRBS s, k Branch if Status Flag Set if (SREG(s) = 1) then PC←PC+k + 1 None 1/2

BRBC s, k Branch if Status Flag Cleared if (SREG(s) = 0) then PC←PC+k + 1 None 1/2

BREQ k Branch if Equal if (Z = 1) then PC ← PC + k + 1 None 1/2

BRNE k Branch if Not Equal if (Z = 0) then PC ← PC + k + 1 None 1/2

BRCS k Branch if Carry Set if (C = 1) then PC ← PC + k + 1 None 1/2

BRCC k Branch if Carry Cleared if (C = 0) then PC ← PC + k + 1 None 1/2

BRSH k Branch if Same or Higher if (C = 0) then PC ← PC + k + 1 None 1/2

BRLO k Branch if Lower if (C = 1) then PC ← PC + k + 1 None 1/2

BRMI k Branch if Minus if (N = 1) then PC ← PC + k + 1 None 1/2

BRPL k Branch if Plus if (N = 0) then PC ← PC + k + 1 None 1/2

BRGE k Branch if Greater or Equal, Signed if (N ⊕ V= 0) then PC ← PC + k + 1 None 1/2

BRLT k Branch if Less Than Zero, Signed if (N ⊕ V= 1) then PC ← PC + k + 1 None 1/2

BRHS k Branch if Half Carry Flag Set if (H = 1) then PC ← PC + k + 1 None 1/2

BRHC k Branch if Half Carry Flag Cleared if (H = 0) then PC ← PC + k + 1 None 1/2

BRTS k Branch if T Flag Set if (T = 1) then PC ← PC + k + 1 None 1/2

BRTC k Branch if T Flag Cleared if (T = 0) then PC ← PC + k + 1 None 1/2

BRVS k Branch if Overflow Flag is Set if (V = 1) then PC ← PC + k + 1 None 1/2

BRVC k Branch if Overflow Flag is Cleared if (V = 0) then PC ← PC + k + 1 None 1/2

BRIE k Branch if Interrupt Enabled if ( I = 1) then PC ← PC + k + 1 None 1/2

BRID k Branch if Interrupt Disabled if ( I = 0) then PC ← PC + k + 1 None 1/2

BIT AND BIT-TEST INSTRUCTIONS

SBI P,b Set Bit in I/O Register I/O(P,b) ← 1None2

CBI P,b Clear Bit in I/O Register I/O(P,b) ← 0None2

LSL Rd Logical Shift Left Rd(n+1) ← Rd(n), Rd(0) ← 0 Z,C,N,V 1

LSR Rd Logical Shift Right Rd(n) ← Rd(n+1), Rd(7) ← 0 Z,C,N,V 1

ROL Rd Rotate Left Through Carry Rd(0)←C,Rd(n+1)← Rd(n),C←Rd(7) Z,C,N,V 1

ATtiny2313/V

2543ES–AVR–04/04

ROR Rd Rotate Right Through Carry Rd(7)←C,Rd(n)← Rd(n+1),C←Rd(0) Z,C,N,V 1

ASR Rd Arithmetic Shift Right Rd(n) ← Rd(n+1), n=0..6 Z,C,N,V 1

SWAP Rd Swap Nibbles Rd(3..0)←Rd(7..4),Rd(7..4)←Rd(3..0) None 1

BSET s Flag Set SREG(s) ← 1 SREG(s) 1

BCLR s Flag Clear SREG(s) ← 0 SREG(s) 1

BST Rr, b Bit Store from Register to T T ← Rr(b) T 1

BLD Rd, b Bit load from T to Register Rd(b) ← TNone1

SEC Set Carry C ← 1C1

CLC Clear Carry C ← 0 C 1

SEN Set Negative Flag N ← 1N1

CLN Clear Negative Flag N ← 0 N 1

SEZ Set Zero Flag Z ← 1Z1

CLZ Clear Zero Flag Z ← 0 Z 1

SEI Global Interrupt Enable I ← 1I1

CLI Global Interrupt Disable I ← 0 I 1

SES Set Signed Test Flag S ← 1S1

CLS Clear Signed Test Flag S ← 0 S 1

SEV Set Twos Complement Overflow. V ← 1V1

CLV Clear Twos Complement Overflow V ← 0 V 1

SET Set T in SREG T ← 1T1

CLT Clear T in SREG T ← 0 T 1

SEH Set Half Carry Flag in SREG H ← 1H1

CLH Clear Half Carry Flag in SREG H ← 0 H 1

DATA TRANSFER INSTRUCTIONS

MOV Rd, Rr Move Between Registers Rd ← Rr None 1

MOVW Rd, Rr Copy Register Word Rd+1:Rd ← Rr+1:Rr None 1

LDI Rd, K Load Immediate Rd ← KNone1

LD Rd, X Load Indirect Rd ← (X) None 2

LD Rd, X+ Load Indirect and Post-Inc. Rd ← (X), X ← X + 1 None 2

LD Rd, - X Load Indirect and Pre-Dec. X ← X - 1, Rd ← (X) None 2

LD Rd, Y Load Indirect Rd ← (Y) None 2

LD Rd, Y+ Load Indirect and Post-Inc. Rd ← (Y), Y ← Y + 1 None 2

LD Rd, - Y Load Indirect and Pre-Dec. Y ← Y - 1, Rd ← (Y) None 2

LDD Rd,Y+q Load Indirect with Displacement Rd ← (Y + q) None 2

LD Rd, Z Load Indirect Rd ← (Z) None 2

LD Rd, Z+ Load Indirect and Post-Inc. Rd ← (Z), Z ← Z+1 None 2

LD Rd, -Z Load Indirect and Pre-Dec. Z ← Z - 1, Rd ← (Z) None 2

LDD Rd, Z+q Load Indirect with Displacement Rd ← (Z + q) None 2

LDS Rd, k Load Direct from SRAM Rd ← (k) None 2

ST X, Rr Store Indirect (X) ← Rr None 2

ST X+, Rr Store Indirect and Post-Inc. (X) ← Rr, X ← X + 1 None 2

ST - X, Rr Store Indirect and Pre-Dec. X ← X - 1, (X) ← Rr None 2

ST Y, Rr Store Indirect (Y) ← Rr None 2

ST Y+, Rr Store Indirect and Post-Inc. (Y) ← Rr, Y ← Y + 1 None 2

ST - Y, Rr Store Indirect and Pre-Dec. Y ← Y - 1, (Y) ← Rr None 2

STD Y+q,Rr Store Indirect with Displacement (Y + q) ← Rr None 2

ST Z, Rr Store Indirect (Z) ← Rr None 2

ST Z+, Rr Store Indirect and Post-Inc. (Z) ← Rr, Z ← Z + 1 None 2

ST -Z, Rr Store Indirect and Pre-Dec. Z ← Z - 1, (Z) ← Rr None 2

STD Z+q,Rr Store Indirect with Displacement (Z + q) ← Rr None 2

STS k, Rr Store Direct to SRAM (k) ← Rr None 2

LPM Load Program Memory R0 ← (Z) None 3

LPM Rd, Z Load Program Memory Rd ← (Z) None 3

LPM Rd, Z+ Load Program Memory and Post-Inc Rd ← (Z), Z ← Z+1 None 3

SPM Store Program Memory (Z) ← R1:R0 None -

IN Rd, P In Port Rd ← PNone1

OUT P, Rr Out Port P ← Rr None 1

PUSH Rr Push Register on Stack STACK ← Rr None 2

POP Rd Pop Register from Stack Rd ← STACK None 2

MCU CONTROL INSTRUCTIONS

NOP No Operation None 1

SLEEP Sleep (see specific descr. for Sleep function) None 1

WDR Watchdog Reset (see specific descr. for WDR/timer) None 1

BREAK Break For On-chip Debug Only None N/A

Mnemonics Operands Description Operation Flags #Clocks

10 ATtiny2313/V

2543ES–AVR–04/04

Ordering Information

Note: 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information

and minimum quantities.

2. Pb-free packaging alternative.

3. See Figure 81 on page 177 and Figure 82 on page 177.

Speed (MHz) Power Supply Ordering Code Package(1) Operation Range

10(3) 1.8 - 5.5V

ATtiny2313V-10PI

ATtiny2313V-10PJ(2)

ATtiny2313V-10SI

ATtiny2313V-10SJ(2)

20P3

20S

Industrial

(-40°C to 85°C)

20(3) 2.7 - 5.5V

ATtiny2313-20PI

ATtiny2313-20PJ(2)

ATtiny2313-20SI

ATtiny2313-20SJ(2)

20P3

20S

Industrial

(-40°C to 85°C)

Package Type

20P3 20-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP)

20S 20-lead, 0.300" Wide, Plastic Gull Wing Small Outline (SOIC)

ATtiny2313/V

2543ES–AVR–04/04

Packaging Information

20P3

2325 Orchard Parkway

San Jose, CA 95131

TITLE DRAWING NO.

REV.

20P3, 20-lead (0.300"/7.62 mm Wide) Plastic Dual

Inline Package (PDIP) C

20P3

1/12/04

SEATING PLANE

COMMON DIMENSIONS

(Unit of Measure = mm)

SYMBOL MIN NOM MAX NOTE

A – – 5.334

A1 0.381 – –

D 25.493 – 25.984 Note 2

E 7.620 – 8.255

E1 6.096 – 7.112 Note 2

B 0.356 – 0.559

B1 1.270 – 1.551

L 2.921 – 3.810

C 0.203 – 0.356

eB – – 10.922

eC 0.000 – 1.524

e 2.540 TYP

Notes: 1. This package conforms to JEDEC reference MS-001, Variation AD.

2. Dimensions D and E1 do not include mold Flash or Protrusion.

Mold Flash or Protrusion shall not exceed 0.25 mm (0.010").

12 ATtiny2313/V

2543ES–AVR–04/04

20S

2325 Orchard Parkway

San Jose, CA 95131

TITLE DRAWING NO.

REV.

20S2, 20-lead, 0.300" Wide Body, Plastic Gull

Wing Small Outline Package (SOIC)

1/9/02

20S2 A

End View

Side View

Top View

COMMON DIMENSIONS

(Unit of Measure = inches)

SYMBOL MIN NOM MAX NOTE

Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-013, Variation AC for additional information.

2. Dimension "D" does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed

0.15 mm (0.006") per side.

3. Dimension "E" does not include inter-lead Flash or protrusion. Inter-lead Flash and protrusions shall not exceed 0.25 mm

(0.010") per side.

4. "L" is the length of the terminal for soldering to a substrate.

5. The lead width "b", as measured 0.36 mm (0.014") or greater above the seating plane, shall not exceed a maximum value of 0.61 mm

(0.024") per side.

A 0.0926 0.1043

A1 0.0040 0.0118

b 0.0130 0.0200 4

C 0.0091 0.0125

D 0.4961 0.5118 1

E 0.2914 0.2992 2

H 0.3940 0.4190

L 0.0160 0.050 3

e 0.050 BSC

ATtiny2313/V

2543ES–AVR–04/04

Errata The revision in this section refers to the revision of the ATtiny2313 device.

ATtiny2313 Rev B •Wrong values read after Erase Only operation

•Parallel Programming does not work

•Watchdog Timer Interrupt disabled

1. Wrong values read after Erase Only operation

At supply voltages below 2.7 V, an EEPROM location that is erased by the Erase

Only operation may read as programmed (0x00).

Problem Fix/Workaround

If it is necessary to read an EEPROM location after Erase Only, use an Atomic Write

operation with 0xFF as data in order to erase a location. In any case, the Write Only

operation can be used as intended. Thus no special considerations are needed as

long as the erased location is not read before it is programmed.

2. Parallel Programming does not work

Parallel Programming is not functioning correctly. Because of this, reprogramming

of the device is impossible if one of the following modes are selected:

– In-System Programming disabled (SPIEN unprogrammed)

– Reset Disabled (RSTDISBL programmed)

Problem Fix/Workaround

Serial Programming is still working correctly. By avoiding the two modes above, the

device can be reprogrammed serially.

3. Watchdog Timer Interrupt disabled

If the watchdog timer interrupt flag is not cleared before a new timeout occurs, the

watchdog will be disabled, and the interrupt flag will automatically be cleared. This is

only applicable in interrupt only mode. If the Watchdog is configured to reset the

device in the watchdog time-out following an interrupt, the device works correctly.

Problem fix / Workaround

Make sure there is enough time to always service the first timeout event before a

new watchdog timeout occurs. This is done by selecting a long enough time-out

period.

ATtiny2313 Rev A Revision A has not been sampled.

14 ATtiny2313/V

2543ES–AVR–04/04

Datasheet Change

Log for ATtiny2313

Please note that the referring page numbers in this section are referred to this docu-

ment. The referring revision in this section are referring to the document revision.

Changes from Rev.

2514D-03/04 to Rev.

2514E-04/04

Changes from Rev.

2514C-12/03 to Rev.

2514D-03/04

Changes from Rev.

2514B-09/03 to Rev.

2514C-12/03

Changes from Rev.

2514A-09/03 to Rev.

2514B-09/03

1. Speed Grades changed

- 12MHz to 10MHz

- 24MHz to 20MHz

2. Updated Figure 1 on page 2.

3. Updated “Ordering Information” on page 10.

4. Updated “Maximum Speed vs. VCC” on page 177.

1. Updated Table 2 on page 22.

2. Replaced “Watchdog Timer” on page 38.

3. Added “Maximum Speed vs. VCC” on page 177.

4. “Serial Programming Algorithm” on page 171 updated.

5. Changed mA to µA in preliminary Figure 110 on page 192.

6. “Ordering Information” on page 10 updated.

MLF package option removed

7. Package drawing “20P3” on page 11 updated.

8. Updated C-code examples.

9. Renamed instances of SPMEN to SELFPRGEN, Self Programming

Enable.

1. Updated “Calibrated Internal RC Oscillator” on page 24.

1. Fixed typo from UART to USART and updated Speed Grades and Power

Consumption Estimates in “Features” on page 1.

2. Updated “Pin Configurations” on page 2.

3. Updated Table 15 on page 33 and Table 80 on page 176.

4. Updated item 5 in “Serial Programming Algorithm” on page 171.

5. Updated “Electrical Characteristics” on page 175.

6. Updated Figure 81 on page 177 and added Figure 82 on page 177.

7. Changed SFIOR to GTCCR in “Register Summary” on page 6.

8. Updated “Ordering Information” on page 10.

9. Added new errata in “Errata” on page 13.

Printed on recycled paper.

Disclaimer: Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard

warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any

errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and

does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are

granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use

as critical components in life support devices or systems.

Atmel Corporation Atmel Operations

2325 Orchard Parkway

San Jose, CA 95131, USA

Tel: 1(408) 441-0311

Fax: 1(408) 487-2600

Regional Headquarters

Europe

Atmel Sarl

Route des Arsenaux 41

Case Postale 80

CH-1705 Fribourg

Switzerland

Tel: (41) 26-426-5555

Fax: (41) 26-426-5500

Asia

Room 1219

Chinachem Golden Plaza

77 Mody Road Tsimshatsui

East Kowloon

Hong Kong

Tel: (852) 2721-9778

Fax: (852) 2722-1369

Japan

9F, Tonetsu Shinkawa Bldg.

1-24-8 Shinkawa

Chuo-ku, Tokyo 104-0033

Japan

Tel: (81) 3-3523-3551

Fax: (81) 3-3523-7581

Memory

2325 Orchard Parkway

San Jose, CA 95131, USA

Tel: 1(408) 441-0311

Fax: 1(408) 436-4314

Microcontrollers

2325 Orchard Parkway

San Jose, CA 95131, USA

Tel: 1(408) 441-0311

Fax: 1(408) 436-4314

La Chantrerie

BP 70602

44306 Nantes Cedex 3, France

Tel: (33) 2-40-18-18-18

Fax: (33) 2-40-18-19-60

ASIC/ASSP/Smart Cards

Zone Industrielle

13106 Rousset Cedex, France

Tel: (33) 4-42-53-60-00

Fax: (33) 4-42-53-60-01

1150 East Cheyenne Mtn. Blvd.

Colorado Springs, CO 80906, USA

Tel: 1(719) 576-3300

Fax: 1(719) 540-1759

Scottish Enterprise Technology Park

Maxwell Building

East Kilbride G75 0QR, Scotland

Tel: (44) 1355-803-000

Fax: (44) 1355-242-743

RF/Automotive

Theresienstrasse 2

Postfach 3535

74025 Heilbronn, Germany

Tel: (49) 71-31-67-0

Fax: (49) 71-31-67-2340

1150 East Cheyenne Mtn. Blvd.

Colorado Springs, CO 80906, USA

Tel: 1(719) 576-3300

Fax: 1(719) 540-1759

Biometrics/Imaging/Hi-Rel MPU/

High Speed Converters/RF Datacom

Avenue de Rochepleine

BP 123

38521 Saint-Egreve Cedex, France

Tel: (33) 4-76-58-30-00

Fax: (33) 4-76-58-34-80

Literature Requests

www.atmel.com/literature

2543ES–AVR–04/04

Atmel Corporation or its subsidiaries. Microsoft®, Windows®, Windows NT®, and Windows XP® are the registered trademarks of Microsoft Corpo-

ration. Other terms and product names may be the trademarks of others