LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS
Inverter-use screw terminal, 105C
CAT. No. E1001K
@Higher ripple capability than LXA series
@Endurance with ripple current : 5,000 hours at 105C
@RoHS Compliant
?SPECIFICATIONS
(at 20C, 120Hz)
(at 20C after 5 minutes)
(at 20C, 120Hz)
(at 120Hz)
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tane)
Low Temperature
Characteristics
Insulation Resistance
Insulation
Withstanding Voltage
Endurance
Shelf Life
Items
-
25 to +105C
350 to 450Vdc
P20% (M)
I=0.02CV or 5mA, whichever is smaller.
Where, I : Max. leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (V)
0.15max.
Capacitance change C (
-
25C)/C(+20C)]0.7
When measured between the terminals that are connected to each other and to the mounting clamp on the insulating sleeve covering
the case by using an insulation resistance meter of 500Vdc, the insulation resistance shall not be less than than 100MO.
When a voltage of 2,000Vac is applied for 1 minute between the terminals that are connected to each other and to the mounting clamp
on the insulating sleeve covering the case, there shall not be electrical damage.
The following specifications shall be satisfied when the capacitors are restored to 20C after subjected to DC voltage with the rated
ripple current is applied for 5,000 hours at 105C.
Capacitance change [P20% of the initial value
D.F. (tanE)[200% of the initial specified value
Leakage current [The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20C after exposing them for 1,000 hours at 105C without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change [P20% of the initial value
D.F. (tanE)[200% of the initial specified value
Leakage current [The initial specified value
Characteristics
?DIMENSIONS (Screw-Mount) [mm]
?PART NUMBERING SYSTEM
@Mounting Clamp Code : B
* The screw and the mounting clamp are separately supplied and not attached to the product.
L+4max. G
P
1
FD+1.8max.
FP1
Sleeve (Pb-free PVC : Brown)
Plastic disk
6
AP1
WP1
4.5
BP1
30°P5°
360°
3
45°P5°
8
J
KP1
EP1
4.5
@Mounting Clamp Code : C
fD
63.5
76.2
A
90
104.5
B
76
90
W
80
93.5
F
28.0
31.5
fD
63.5
76.2
89
100
E
38.1
44.5
50.8
56.5
K
43.5
50.0
56.5
63.4
F
28.0
31.5
31.5
41.5
J
14.0
14.0
16.0
18.0
F63.5 & F76.2 : G=6
F89 : G=4
F100 : G=10
<Screw specifi cations>
F63.5 to F89
Plus hexagon-headed screw :
M5B0.8B10
Maximum screw tightening torque :
3.23Nm
F100
Cross-recessed head (Phillips) screw :
M8B1.25B16
Spring washer
Washer
Maximum screw tightening torque :
6.31Nm
Higher ripple
LXR
LXA
@Terminal Code : LG
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 3,300MF:332, 10,000MF:103)
Mounting clamp code (N, B, C)
Terminal code
Voltage code (ex. 350V:351,400V:401)
Series code
Category
E L X R A A A L G N A A A A A A MM
13426789105121311 16 17 181514
Please refer to "Product code guide (screw-mount terminal type)"
(1/2)
LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS
Inverter-use screw terminal, 105C
CAT. No. E1001K
?STANDARD RATINGS
?RATED RIPPLE CURRENT MULTIPLIERS
@Frequency Mul ti pli ers
120
1.0 300
1.1 1k
1.3 3k
1.4
Frequency (Hz)
Coefficient
The endurance of capacitors is reduced with internal heating produced by ripple current at the rate of halving the lifetime with every 5 to
10C rise. When long life performance is required in actual use, the rms ripple current has to be reduced. Also, for the LXR series capacitors,
using them at operating voltage less than their rated voltage can extend their lifetime. For details, please contact a representative of Nippon
Chemi-Con.
WV
(Vdc)Cap
(mF) Case size
fDbL(mm) tane
Rated ripple
current
(Arms/
105c,120Hz)
Part No.
350
3,300 63.5B115 0.15 14.4 ELXR351LGC332MDB5M
3,900 63.5B130 0.15 16.6 ELXR351LGC392MDD0M
4,700 63.5B155 0.15 19.8 ELXR351LGC472MDF5M
4,700 76.2B115 0.15 19.1 ELXR351LGC472MEB5M
5,600 63.5B170 0.15 22.5 ELXR351LGC562MDH0M
5,600 76.2B130 0.15 21.9 ELXR351LGC562MED0M
6,800 76.2B155 0.15 26.2 ELXR351LGC682MEF5M
8,200 76.2B170 0.15 30.0 ELXR351LGC822MEH0M
8,200 89B155 0.15 29.2 ELXR351LGC822MFF5M
10,000 89B170 0.15 33.7 ELXR351LGC103MFH0M
12,000 100B190 0.15 37.8 ELXR351LGC123MGK0M
15,000 100B250 0.15 47.7 ELXR351LGC153MGR0M
400
2,700 63.5B115 0.15 13.1 ELXR401LGC272MDB5M
3,300 63.5B130 0.15 15.2 ELXR401LGC332MDD0M
3,900 63.5B155 0.15 17.9 ELXR401LGC392MDF5M
3,900 76.2B115 0.15 18.2 ELXR401LGC392MEB5M
4,700 63.5B170 0.15 20.5 ELXR401LGC472MDH0M
4,700 76.2B130 0.15 20.1 ELXR401LGC472MED0M
5,600 76.2B155 0.15 23.8 ELXR401LGC562MEF5M
WV
(Vdc)Cap
(mF) Case size
fDbL(mm) tane
Rated ripple
current
(Arms/
105c,120Hz)
Part No.
400
6,800 76.2B170 0.15 27.3 ELXR401LGC682MEH0M
6,800 89B155 0.15 26.6 ELXR401LGC682MFF5M
8,200 89B170 0.15 30.5 ELXR401LGC822MFH0M
10,000 100B190 0.15 34.5 ELXR401LGC103MGK0M
12,000 100B220 0.15 40.2 ELXR401LGC123MGN0M
450
2,200 63.5B115 0.15 11.8 ELXR451LGC222MDB5M
2,700 63.5B130 0.15 13.7 ELXR451LGC272MDD0M
2,700 76.2B115 0.15 14.5 ELXR451LGC272MEB5M
3,300 63.5B155 0.15 16.5 ELXR451LGC332MDF5M
3,300 76.2B130 0.15 16.9 ELXR451LGC332MED0M
3,900 63.5B170 0.15 18.7 ELXR451LGC392MDH0M
4,700 76.2B155 0.15 21.7 ELXR451LGC472MEF5M
5,600 76.2B190 0.15 26.1 ELXR451LGC562MEK0M
5,600 89B155 0.15 24.1 ELXR451LGC562MFF5M
6,800 89B170 0.15 27.8 ELXR451LGC682MFH0M
8,200 89B190 0.15 32.0 ELXR451LGC822MFK0M
10,000 100B220 0.15 36.8 ELXR451LGC103MGN0M
12,000 100B250 0.15 42.7 ELXR451LGC123MGR0M
(2/2)
