67997-214HLF - FCI - Datasheet.Support

NUMBER

BUS-12-050

TYPE

PRODUCT SPECIFICATION

TITLE PAGE REVISION

BERGSTIK® /BERGSTIK™ Headers

1 of 8 L

AUTHORIZED BY DATE

M.Zhou 07 JUL 16

CLASSIFICATION

UNRESTRICTED

This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI. No part of the information shown on the

document may be used in any way or disclosed to others without the written consent of FCI. Copyright FCI.

Form E-3005

Rev F

GS-01-001

1.0 GENERAL

1.1 SCOPE

This specification covers the Bergstik®and Bergstrip™ Headers, designed for use in low-power

applications requiring a printed wiring -board mounted straight or right angle disconnect. The header

provides only the pin half of the interconnection, using any 0.025” square pin mateable receptacle to

complete the connection. This product is Lead Free and meets the requirement of the European

Union Directive of Restrictions for Hazardous Substances (Directive 2002/95/EC). The specification

is composed of the following sections:

Paragraph Title

1.0 GENERAL

1.1 Scope

1.2 Type

2.0 APPLICABLE DOCUMENTS

3.0 REQUIREMENTS

3.1 Qualification

3.2 Material

3.3 Finish

3.4 Design and construction

3.5 Electrical Characteristics

3.6 Mechanical characteristics

3.7 Environmental Conditions

4.0 QUALITY ASSURANCE PROVISIONS

4.1 Equipment Calibration

4.2 Inspection Conditions

4.3 Qualification Inspection

4.4 Acceptance Inspection

1.2 Working parameter

current rating: 5A

voltage : 110V

operating temperature: -65o to 105o C - Nylon

-65o to 130o C - PCT,PPS & LCP

PDS: Rev :L STATUS:Released Printed: Jul 21, 2016

NUMBER

BUS-12-050

TYPE

PRODUCT SPECIFICATION

TITLE PAGE REVISION

BERGSTIK® /BERGSTIK™ Headers

2 of 8 L

AUTHORIZED BY DATE

M.Zhou 07 JUL 16

CLASSIFICATION

UNRESTRICTED

This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI. No part of the information shown on the

document may be used in any way or disclosed to others without the written consent of FCI. Copyright FCI.

Form E-3005

Rev F

GS-01-001

2.0 APPLICABLE DOCUMENTS

The following documents, of the issue in effect on the date of the latest revision of this specification, shall

form a part of this specification to the extent specified herein.

Military Specifications

MIL-F-14256 Flux, Soldering, Liquid (Rosin Base), Activated

MIL-G-45204 Gold Plating, Electrodeposited

MIL-P-45209 Palladium Plating, Electrodeposited

MIL-P-55110 Printer Wiring Boards

MIL-P81728 Plating, Tin-Leaded (Electrodeposited)

Federal Specifications

QQ-N-290 Nickel Plating (Electrodeposited)

QQ-W-343 Wire, Electrical and Nonelectrical, Copper (Uninsulated)

QQ-S-571 Solder: Lead Alloy, Tin-Lead Allow, and Tin Alloy, Flux Cored

Ribbon and Wire, and Solid Form

Military Standards

MIL-STD-105 Sampling Procedures & Tables for Inspection by Attributes

MIL-STD-202 Test Methods for Electrical and Electronic Component Parts

MIL-STD-275 Printed Wiring for Electronic Equipment

MIL-STD-1344 Test Methods for Electrical Connectors

ISO-9000 Calibration System Requirements

Industry Specifications/Standards

UL-94 Tests for Flammability of Plastic Materials

ASTM B-159 Phosphor Bronze Wire

ASTM D-2897 Reinforced & Filled Nylon Injection Molding & Extrusion

Materials

FCI Labs Reports- Supporting Data

ZA5-2625 Lead Free Plating Investigation

3.0 REQUIREMENTS

3.1 Qualification

Headers furnished under this specification shall be products capable of meeting or exceeding the

qualification test requirements specified herein.

3.2 Material

PDS: Rev :L STATUS:Released Printed: Jul 21, 2016

NUMBER

BUS-12-050

TYPE

PRODUCT SPECIFICATION

TITLE PAGE REVISION

BERGSTIK® /BERGSTIK™ Headers

3 of 8 L

AUTHORIZED BY DATE

M.Zhou 07 JUL 16

CLASSIFICATION

UNRESTRICTED

This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI. No part of the information shown on the

document may be used in any way or disclosed to others without the written consent of FCI. Copyright FCI.

Form E-3005

Rev F

GS-01-001

The material for each part shall be specified herein, or equivalent. Substitute material shall meet or

exceed the performance requirements of this specification.

3.2.1 Contact. The contact shall be Phosphor Bronze Alloy UNS C51000 in accordance with

ASTM B-159 or other copper alloy as specified on the product drawing.

3.2.2 Insulator. The insulator shall be glass- or mineral-filled nylon in accordance with ASTM

D-2897, polyphenylene sulfide (PPS) ,PCT or LCP. All plastic material shall be

rated V-0 in accordance with UL-94.

3.3 Finish

The finish of the contact shall be specified herein for the particular type of header under

consideration.

3.3.1 Solder tails. As defined by product drawings, will be plated with the specified thickness of

pure tin for Lead Free. Or 93/7 tin-lead per MIL-P-81728 option. Or gold per MIL-G-45204

Type II, Grade C option. Or palladium alloy per MIL-P-45209 option.

Tin plated “LF” product has 100% tin plating in the interface and has not been tested for

whisker growth in all interconnect environments

3.3.2 Contact Area. As defined by product drawings, will be plated with the specified thickness

of pure tin for Lead Free. Or 93/7 tin-lead per MIL-P-81728 option. Or gold per MIL-G-

45204 Type II, Grade C option. Or palladium alloy per MIL-P-45209 option.

Tin plated “LF” product has 100% tin plating in the interface and has not been tested for

whisker growth in all interconnect environments

3.3.3 All other areas. Will be plated with 50 microinches of nickel per QQ-N-290, Class 2.

3.4 Design and Construction

The header shall be a multi-piece assembly having one or two rows of contacts with solderable tail

ends for installation in .040 inch diameter holes in printed wiring boards of standard thickness. The

Bergstik® header contacts shall be insert molded or post-inserted in the insulator on rectangular

grids of .100, .125, or .150 inches or multiples thereof and shall be available in straight or right angle

configurations. The Bergstrip™ header contacts shall be post-inserted into the insulator on

rectangular grids of .100 inch and shall be available in straight configurations. The contacts shall be

available in various above- and below-board lengths suitable for use as 0.025 inch square male

disconnects or as similarly configured wrapposts for solderless wrapped connections in accordance

with MIL-STD-1130.

PDS: Rev :L STATUS:Released Printed: Jul 21, 2016

NUMBER

BUS-12-050

TYPE

PRODUCT SPECIFICATION

TITLE PAGE REVISION

BERGSTIK® /BERGSTIK™ Headers

4 of 8 L

AUTHORIZED BY DATE

M.Zhou 07 JUL 16

CLASSIFICATION

UNRESTRICTED

This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI. No part of the information shown on the

document may be used in any way or disclosed to others without the written consent of FCI. Copyright FCI.

Form E-3005

Rev F

GS-01-001

3.4.1 Polarization (Optional). Removal or omission of individual contact(s) shall provide

polarization/keying to insure correct orientation of the header and an appropriately

configured mating part.

3.4.2 Workmanship. Headers shall be uniform in quality and shall be free from burrs, voids,

chips, blisters, holes, sharp edges, or other defects that will adversely affect life or

serviceability.

3.5 Electrical Characteristics

3.5.1 Insulation Resistance. The insulation resistance of the unmated and unsoldered headers

shall be not less than 5000 megohms when measured in accordance with MIL-STD-1344,

Method 3003. The following details shall apply:

a. Test Condition - 500 volts DC applied for l minute.

b. Points of Measurement - Between individually paired

adjacent and opposing contacts.

3.5.2 Dielectric Withstanding Voltage. There shall be no evidence of arc-over, insulation

breakdown, or excessive leakage current (>1 milliampere) when the unmated and

unsoldered header is tested in accordance with MIL-STD-1344, Method 3001. The

following details shall apply:

a. Test Potential - See Table I.

b. Test Duration - 50 seconds.

c. Test Condition - I (760 Torr - sea level).

d. Points of Measurement - Between individually paired adjacent and opposing contacts.

TABLE I - DIELECTRIC WITHSTANDING VOLTAGE

Contact Spacing

( inch ) Test Voltage

VRMS

.100 1500

.125 1500

.150 1500

PDS: Rev :L STATUS:Released Printed: Jul 21, 2016

NUMBER

BUS-12-050

TYPE

PRODUCT SPECIFICATION

TITLE PAGE REVISION

BERGSTIK® /BERGSTIK™ Headers

5 of 8 L

AUTHORIZED BY DATE

M.Zhou 07 JUL 16

CLASSIFICATION

UNRESTRICTED

This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI. No part of the information shown on the

document may be used in any way or disclosed to others without the written consent of FCI. Copyright FCI.

Form E-3005

Rev F

GS-01-001

3.6 Mechanical Characteristics

3.6.1 Contact Retention. Individual contacts in an unsoldered header shall withstand a load

applied in either direction, along the contact axis, without dislodgement from the insulator,

of 5.0 pounds in the case of insert molded contacts and 2.0 pounds in the case of post

inserted contacts.

3.7 Environmental Conditions

3.7.1 Thermal Shock. After exposure of an unmated and unsoldered header to alternate

periods of extreme high and low temperature, there shall be no evidence of cracking or

crazing of the insulator（not include open knit line） or other physical damage to the

header. The dielectric withstanding voltage shall be not less than 750 volts RMS 60 HZ

(see Paragraph 3.5.2). The following details shall apply:

a. Test Conditions - B (1 hour cycles).

b. Temperature Range - -65o to 105o C - Nylon

-65o to 130o C - PCT,PPS & LCP

3.7.2 High Temperature Life. After exposure of an unmated and unsoldered header to a high

temperature operating environment, the insulation resistance of the header shall be not

less than 5,000 megohms (see Paragraph 3.5.1). The test shall be in accordance with

MIL-STD-202, Method 108. The following details shall apply:

a. Test Chamber Temperature -105o C ( + 2o)-Nylon;130oC( + 2o) PCT,PPS & LCP

b. Test Condition (Duration) B (250 hours).

c. Operating Conditions - No Current

3.8 Solderability

Plated pins shall be capable of passing BUS-19-002.

3.9 Re-Qualification product

If either of the following conditions occurs, the responsible product engineer shall initiate re-

qualification testing, consisting of all applicable parts of the qualification test matrix, table II

a. A significant design change is made to the existing product. A significant change shall

include, but is not limited to, changes in the contact material composition, contact material

thickness, contact force, contact surface geometry, underlying material composition,

underlying material thickness, insulation design, contact base material or contact lubrication

requirements.

b. A significant change is made to the manufacturing process which impacts the product form,

fit or function.

c. A significant event occurs during the production or end use requiring corrective action to be

taken relative to the product design or manufacturing process.

PDS: Rev :L STATUS:Released Printed: Jul 21, 2016

NUMBER

BUS-12-050

TYPE

PRODUCT SPECIFICATION

TITLE PAGE REVISION

BERGSTIK® /BERGSTIK™ Headers

6 of 8 L

AUTHORIZED BY DATE

M.Zhou 07 JUL 16

CLASSIFICATION

UNRESTRICTED

This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI. No part of the information shown on the

document may be used in any way or disclosed to others without the written consent of FCI. Copyright FCI.

Form E-3005

Rev F

GS-01-001

4.0 QUALITY ASSURANCE PROVISIONS

4.1 Equipment Calibration

All test equipment and inspection facilities used in the performance of any test shall be maintained in

a calibration system in accordance with ISO 9000.

4.2 Inspection Condition

Unless otherwise specified herein, all inspections shall be performed under the following ambient

conditions:

a. Temperature: 25oC + 5o C.

b. Relative Humidity: 30 to 80%.

c. Barometric Pressure: Local Ambient

4.3 Qualification Inspection

Qualification inspection shall be performed on sample units produced with equipment and

procedures normally used in production.

4.3.1 Sample. The qualification sample shall consist of two of the largest size headers of the

particular design, configuration, and type that are the subject of the test.

4.3.2 Test Sequence. The sample headers shall be subjected to the inspections specified in

Table II in the order shown.

TABLE II - CONNECTOR QUALIFICATION INSPECTION

Examination or Test Paragraph Test Sample

1 2

Contact Retention 3.6.1 X -

Insulation Resistance 3.5.1 X -

Dielectric Withstanding Voltage 3.5.3 X -

Thermal Shock 3.7.1 X -

Insulation Resistance 3.5.1 X -

Dielectric Withstanding Voltage 3.5.2 X -

High Temperature Life 3.7.2 X -

Insulation Resistance 3.5.1 X -

Dielectric Withstanding Voltage 3.5.2 X -

Solderability 3.8 - X

4.4 Acceptance Inspection

Acceptance inspection shall consist of the examinations specified in Table III. Appropriate in-

process inspection may, at the option of FCI, be substituted for the indicated lot sampling/inspection

provided the process output quality level is maintained.

PDS: Rev :L STATUS:Released Printed: Jul 21, 2016

NUMBER

BUS-12-050

TYPE

PRODUCT SPECIFICATION

TITLE PAGE REVISION

BERGSTIK® /BERGSTIK™ Headers

7 of 8 L

AUTHORIZED BY DATE

M.Zhou 07 JUL 16

CLASSIFICATION

UNRESTRICTED

This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI. No part of the information shown on the

document may be used in any way or disclosed to others without the written consent of FCI. Copyright FCI.

Form E-3005

Rev F

GS-01-001

TABLE III - ACCEPTANCE INSPECTION

Examination AQL

Major Minor

Visual and Mechanical 1.0% 4.0%

4.4.1 Inspection Lot. An inspection lot shall consist of all headers produced under essentially

the same conditions and offered for inspection at one time.

4.4.2 Sampling Plan. Statistical sampling and inspection shall be in accordance with MIL-STD-

105, General Inspection Level II. The Acceptance Quality Level (AQL) shall be as

specified in Table III. Major and minor defects shall be as defined in MIL-STD-105.

4.4.3 Reject Lots. Rejected lots shall be reworked to correct the defects or screened to

remove defective units and resubmitted for inspection.

4.4.4 Deposition of Sample Units. Sample units that have been subjected to the acceptance

inspection shall be considered deliverable on the contract or purchase order.

PDS: Rev :L STATUS:Released Printed: Jul 21, 2016

NUMBER

BUS-12-050

TYPE

PRODUCT SPECIFICATION

TITLE PAGE REVISION

BERGSTIK® /BERGSTIK™ Headers

8 of 8 L

AUTHORIZED BY DATE

M.Zhou 07 JUL 16

CLASSIFICATION

UNRESTRICTED

This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI. No part of the information shown on the

document may be used in any way or disclosed to others without the written consent of FCI. Copyright FCI.

Form E-3005

Rev F

GS-01-001

REVISION RECORD

REV PAGE DESCRIPTION EC# DATE

B 5 V11389 05/10/91

C 2 to 7 Delete MIL-STD-1130, add polyphenylene sulfide (PPS) to

3.2.2, delete 3.4.1,3.5.3,3.6.2 & 3.6.3. Delete Figure 1.

Delete Wrappost Torque and Contact Retention from table

II

V12665 09/24/91

D 3 Update 3.2.2 to add PCT resin, delete the word minimum

on 3.3.1 & 3.3.3

V40635 03/17/94

E 1 to 8 Add Bergstrip™ Header to Title. Replace connector with

header. Replace unterminated with unsoldered. Replace

DuPont with Berg.

V80237 02/04/98

F 1,3,5 Change Title from Packaging Spec to Product Spec. 3.3.2

change 150 to 120. 3.7.1 & 3.7.2 add temperature -65 ° to

130 ° add name ( Nylon).

V81231 06/23/98

G All Revised format to be consistent with GS-01-001, and

change BERG, Dupont, etc. references to FCI.

V01904 07/28/00

H 1 to 3 Add lead free information M06-0161 3/13/06

J 5 Add r-qualification notes 3.9 M07-0280 06/20/07

K 1,3,4,5 Delete notes 1.2,change note 3.3 of the plating, delete

‘‘cracks and scratches’’, add ‘‘not include open knit line’’. ELX-N-006141 09/19/11

L 1 Add working parameter content ELX-N-24463 07/07/16

PDS: Rev :L STATUS:Released Printed: Jul 21, 2016

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

FCI / Amphenol:

67997-400HLF 67998-400HLF 68000-100HLF 68000-102HLF 68000-400HLF 68000-403HLF 68002-100HLF

68015-236HLF 68024-400HLF 68691-400HLF 78511-100HLF 78511-400HLF 67996-172HLF 68004-102HLF

68015-401HLF 67996-130HLF 67996-140HLF 67996-234HLF 68015-407HLF 68020-172HLF 67996-108HLF

67996-120HLF 67996-126HLF 67996-164HLF 67996-210HLF 67996-410HLF 67996-414HLF 67997-104HLF

67997-106HLF 67997-108HLF 67997-120HLF 67997-124HLF 67997-138HLF 67996-416HLF 68000-409HLF

78290-136HLF 78511-136HLF 78511-404HLF 87901-440HLF 87901-472HLF 94063-416HLF 67996-124HLF

67996-402HLF 67996-412HLF 67996-426HLF 67996-434HLF 67997-118HLF 68000-116HLF 68000-220HLF

68000-225HLF 68000-407HLF 68000-411HLF 68000-412HLF 68000-413HLF 68000-416HLF 68000-418HLF

68000-420HLF 68000-422HLF 68000-424HLF 68000-425HLF 68000-426HLF 68000-428HLF 68000-432HLF

68000-433HLF 68002-104HLF 68002-105HLF 68002-106HLF 68002-110HLF 68002-111HLF 68002-112HLF

68002-114HLF 68002-115HLF 68002-118HLF 68002-121HLF 68002-122HLF 68002-124HLF 68002-125HLF

68002-127HLF 68002-129HLF 68002-131HLF 68002-133HLF 68002-135HLF 68002-204HLF 68002-205HLF

68002-207HLF 68002-208HLF 68002-209HLF 68002-212HLF 68002-217HLF 68002-218HLF 68002-220HLF

68002-223HLF 68002-224HLF 68002-227HLF 68002-228HLF 68002-230HLF 68002-232HLF 68002-234HLF

68002-403HLF 68002-405HLF