Tantalum Surface Mount Capacitors - High Temperature T498 150C Rated MnO2 Series Overview The KEMET T498 Series is a high temperature product that offers optimum performance characteristics in applications with operating temperatures up to 150C. Advanced materials and testing allow this series to perform with a reliability level of 0.5%/1,000 hours at rated voltage and temperature. The T498 Series is available in five standard EIA case sizes with RoHS compliant terminations as standard. Benefits Applications * * * * * * * * * * * * * * Typical applications include decoupling and filtering in industrial and automotive end applications such as DC/DC converters, portable electronics, telecommunications, and control units operating at temperatures up to 150C. Meets or exceeds EIA Standard 535BAAC Taped and reeled per EIA 481-1 Symmetrical, compliant terminations Optional gold-plated terminations Laser-marked case 100% surge current testing Complies with AEC-Q200 Capacitance values of 0.47 F to 220 F Tolerances of 10% and 20% Voltage rating of 6 - 50 VDC 100% steady-state accelerated aging Temperature/voltage derating is 2/3 at 150C RoHS Compliant and lead-free terminations standard Operating temperature range of -55C to +150C Environmental Compliance RoHS Compliant (6/6) according to Directive 2002/95/EC when ordered with 100% Sn solder. SPICE For a detailed analysis of specific part numbers, please visit www.kemet.com for a free download of KEMET's SPICE software. The KEMET SPICE program is freeware intended to aid design engineers in analyzing the performance of these capacitors over frequency, temperature, ripple, and DC bias conditions. One world. One KEMET (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2012_T498 * 3/15/2013 1 Tantalum Surface Mount Capacitors - High Temperature T498 150C Rated MnO2 Series Ordering Information T 498 X 227 M 010 Capacitor Class Series Case Size Capacitance Code (pF) Capacitance Tolerance Voltage High Temperature 150C A, B, C, D, X First two digits represent significant figures. Third digit specifies number of zeros. K = 10% M = 20% T= Tantalum A T Failure Rate/ Lead Material Design 006 = 6.3 V 010 = 10 V 016 = 16 V 020 = 20 V 025 = 25 V 035 = 35 V 050 = 50 V A = N/A Z = N/A T = 100% Matte Tin (Sn) Plated G = Gold Plated E800 ESR Last three digits specify ESR in m. (800 = 800 m) Packaging (C-Spec) Blank = 7" Reel 7280 = 13" Reel Performance Characteristics Item Performance Characteristics Operating Temperature Rated Capacitance Range Capacitance Tolerance Rated Voltage Range -55C to 150C 0.33 - 220 F @ 120 Hz/25C K Tolerance (10%), M Tolerance (20%) 6 - 50 V DF (120 Hz) Refer to Part Number Electrical Specification Table ESR (100 kHz) Refer to Part Number Electrical Specification Table Leakage Current 0.01 CV (A) at rated voltage after 5 minutes (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2012_T498 * 3/15/2013 2 Tantalum Surface Mount Capacitors - High Temperature T498 150C Rated MnO2 Series Qualification Test Condition Characteristics C/C Endurance Storage Life Thermal Shock Temperature Stability 150C @ 2/3 rated voltage, 2,000 hours 150C @ 0 volts, 2,000 hours MIL-STD-202, Method 107, Condition B, mounted, -55C to 150C, 1,000 cycles Extreme temperature exposure at a succession of continuous steps at +25C, -55C, +25C, +85C, +150C, +25C DF Within initial limits DCL Within 1.25 x initial limit ESR Within initial limits C/C Within 10% of initial value DF Within initial limits DCL Within 1.25 x initial limit ESR Within initial limits C/C Within 5% of initial value DF Within initial limits DCL Within 1.25 x initial limit ESR Within initial limits +25C -55C +85C +150C C/C IL* 10% 10% 20% DF IL IL 1.5 x IL 1.5 x IL DCL IL n/a 10 x IL 12 x IL C/C Surge Voltage Mechanical Shock/Vibration Within 10% of initial value 25C and 85C, 1.32 x rated voltage 1,000 cycles (150C, 1.2 x rated voltage) MIL-STD-202, Method 213, Condition I, 100 G peak MIL-STD-202, Method 204, Condition D, 10 Hz to 2,000 Hz, 20 G peak Within 5% of initial value DF Within initial limits DCL Within initial limits ESR Within initial limits C/C Within 10% of initial value DF Within initial limits DCL Within initial limits *IL = Initial Limit (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2012_T498 * 3/15/2013 3 Tantalum Surface Mount Capacitors - High Temperature T498 150C Rated MnO2 Series Electrical Characteristics Capacitance vs. Frequency ESR vs. Frequency 1000 1000 100 T498D476M010ATE600 T498D476M010ATE600_IMP T498X227M010ATE500 100 T498B106M010ATE1K8_ESR Capacitance (F) Impedance, ESR (Ohms) T498B106M010ATE1K8 T498B106M010ATE1K8_IMP T498X227M010ATE500_IMP T498D476M010ATE600_ESR T498X227M010ATE500_ESR 10 1 0.1 10 1 100 1,000 10,000 100,000 1,000,000 Frequency (Hz) 0.1 10,000,000 100 1,000 10,000 100,000 Frequency (Hz) 1,000,000 10,000,000 Dimensions - Millimeters (Inches) Metric will govern Termination cutout at KEMET's option, either end Case Size KEMET EIA A 3216-18 B 3528-21 C 6032-28 D 7343-31 X 7343-43 Component L* W* H* 3.2 0.2 (0.126 0.008) 3.5 02 (0.138 0.008) 6.0 0.3 (0.236 0.03) 7.3 0.3 (0.287 0.012) 7.3 0.3 (0.287 0.012) 1.6 0.2 (0.063 0.008) 2.8 0.2 (0.110 0.008) 3.2 0.3 (0.126 0.012) 4.3 0.3 (0.169 0.012) 4.3 0.3 (0.169 0.012) 1.6 0.2 (0.063 0.008) 1.9 0.2 (0.075 0.008) 2.5 0.3 (0.098 0.012) 2.8 0.3 (0.110 0.012) 4.0 0.3 (0.157 0.012) F* 0.1 S* 0.3 B* 0.15 (.004) (.012) (Ref) .006 1.2 (.047) 0.8 (.031) 0.4 (.016) 2.2 (.087) 0.8 (.031) 0.4 (.016) 2.2 (.087) 1.3 (.051) 0.5 (.020) 2.4 (.094) 1.3 (.051) 0.5 (.020) 2.4 (.094) 1.3 (.051) 0.5 (.020) X (Ref) 0.10 0.10 (.004 .004) 0.10 0.10 (.004 .004) 0.10 0.10 (.004 .004) 0.10 0.10 (.004 .004) 0.10 0.10 (.004 .004) P (Ref) R (Ref) T (Ref) A (Min) G (Ref) E (Ref) 0.4 (.016) 0.4 (.016) 0.13 (.005) 0.5 (.020) 1.0 (.039) 0.13 (.005) 1.1 (0.043) 1.8 (.071) 2.2 (.087) 0.9 (.035) 1.0 (.039) 0.13 (.005) 2.5(.098) 2.8 (.110) 2.4 (.094) 0.9 (.035) 1.0 (.039) 0.13 (.005) 3.8 (.150) 3.5 (.138) 3.5 (.138) 1.7 (.067) 1.0 (.039) 0.13 (.005) 3.8 (.150) 3.5 (.138) 3.5 (.138) 0.8 (.31) 1.1 (.043) 1.3 (.051) Notes: (Ref) - Dimensions provided for reference only. No dimensions provided for B, P or R because low profile cases do not have a bevel or a notch. * MIL-PRF-55365/8 specified dimensions (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2012_T498 * 3/15/2013 4 Tantalum Surface Mount Capacitors - High Temperature T498 150C Rated MnO2 Series Table 1 - Ratings & Part Number Reference Rated Voltage Rated Case Code/ Cap Case Size KEMET Part Number DC Leakage A +20C Max/5 Min 0.6 0.9 1.4 2.1 3.0 6.3 DF ESR VDC F KEMET/EIA 6.3 6.3 6.3 6.3 6.3 6.3 10 15 22 33 47 100 B/3528-21 B/3528-21 C/6032-28 B/3528-21 C/6032-28 D/7343-31 (See below for part options) T498B106(1)006A(2)E2K1 T498B156(1)006A(2)E1K8 T498C226(1)006A(2)E1K3 T498B336(1)006A(2)E1K7 T498C476(1)006A(2)E800 T498D107(1)006A(2)E600 10 10 10 10 10 10 10 10 10 10 10 10 2.2 3.3 4.7 4.7 10 15 15 22 22 47 100 220 A/3216-18 A/3216-18 A/3216-18 B/3528-21 B/3528-21 B/3528-21 C/6032-28 B/3528-21 C/6032-28 D/7343-31 D/7343-31 X/7343-43 T498A225(1)010A(2)E4K6 T498A335(1)010A(2)E3K6 T498A475(1)010A(2)E2K9 T498B475(1)010A(2)E2K7 T498B106(1)010A(2)E1K8 T498B156(1)010A(2)E1K5 T498C156(1)010A(2)E1K8 T498B226(1)010A(2)E1K5 T498C226(1)010A(2)E1K1 T498D476(1)010A(2)E600 T498D107(1)010A(2)E600 T498X227(1)010A(2)E500 0.5 0.5 0.5 0.5 1.0 1.5 1.5 2.2 2.2 4.7 10.0 22.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 8.0 8.0 4600 3600 2900 2700 1800 1500 1800 1500 1100 600 600 500 16 16 16 16 16 16 16 16 16 16 16 16 16 1 3.3 4.7 6.8 6.8 10 10 15 22 33 47 68 100 A/3216-18 A/3216-18 B/3528-21 A/3216-18 B/3528-21 B/3528-21 C/6032-28 C/6032-28 C/6032-28 D/7343-31 D/7343-31 D/7343-31 X/7343-43 T498A105(1)016A(2)E6K5 T498A335(1)016A(2)E3K4 T498B475(1)016A(2)E2K1 T498A685(1)016A(2)E2K6 T498B685(1)016A(2)E1K8 T498B106(1)016A(2)E2K8 T498C106(1)016A(2)E1K4 T498C156(1)016A(2)E1K1 T498C226(1)016A(2)E1K0 T498D336(1)016A(2)E600 T498D476(1)016A(2)E600 T498D686(1)016A(2)E600 T498X107(1)016A(2)E100 0.5 0.5 0.8 1.1 1.1 1.6 1.6 2.4 3.5 5.3 7.5 10.9 16.0 4.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 8.0 20 20 1 10 A/3216-18 C/6032-28 T498A105(1)020A(2)E5K9 T498C106(1)020A(2)E1K1 0.5 2.0 25 25 25 25 25 25 25 0.47 2.2 10 10 15 22 33 A/3216-18 B/3528-21 C/6032-28 D/7343-31 D/7343-31 D/7343-31 D/7343-31 T498A474(1)025A(2)E8K5 T498B225(1)025A(2)E3K0 T498C106(1)025A(2)E1K1 T498D106(1)025A(2)E1K0 T498D156(1)025A(2)E700 T498D226(1)025A(2)E600 T498D336(1)025A(2)E600 0.5 0.6 2.5 2.5 3.8 5.5 8.3 35 35 35 35 35 0.33 1 1.5 3.3 6.8 A/3216-18 A/3216-18 C/6032-28 C/6032-28 D/7343-31 VDC F KEMET/EIA T498A334(1)035A(2)E11K T498A105(1)035A(2)E10K T498C155(1)035A(2)E3K3 T498C335(1)035A(2)E1K7 T498D685(1)035A(2)E900 (See below for part options) 0.5 0.5 0.5 1.2 2.4 A +20C Max/5 Min Rated Voltage Rated Cap Case Code/ Case Size KEMET Part Number DC Leakage Maximum Allowable Ripple Current % @ +20C m @ 20C (mA) 100 kHz 120 Hz Max 100 kHz Max 25C 6.0 2100 201 6.0 1800 217 6.0 1300 291 6.0 1700 224 6.0 800 371 8.0 600 500 Moisture Sensitivity (mA) 100 kHz 85C 181 195 262 202 334 450 (mA) 100 kHz 125C 80 87 116 90 148 200 Reflow Temp 260C 1 1 1 1 1 1 128 144 161 177 217 238 247 238 316 500 500 574 115 130 145 159 195 214 222 214 284 450 450 517 51 58 64 71 87 95 99 95 126 200 200 230 1 1 1 1 1 1 1 1 1 1 1 1 6500 3400 2100 2600 1800 2800 1400 1100 1000 600 600 600 100 107 149 201 170 217 174 280 316 332 500 500 500 1285 96 134 181 153 195 157 252 284 299 450 450 450 1157 43 60 80 68 87 70 112 126 133 200 200 200 514 1 1 1 1 1 1 1 1 1 1 1 1 1 0.5 2.0 5900 1100 113 316 102 284 45 126 1 1 4.0 6.0 6.0 6.0 6.0 6.0 6.0 8500 3000 1100 1000 700 600 600 94 168 316 387 463 500 500 85 151 284 348 417 450 450 38 67 126 155 185 200 200 1 1 1 1 1 1 1 75 78 165 229 367 (mA) 100 kHz 85C 33 35 73 102 163 (mA) 100 kHz 125C 1 1 1 1 1 Reflow Temp 260C 4.0 11000 83 4.0 10000 87 6.0 3300 183 6.0 1700 254 6.0 900 408 % @ +20C m @ 20C (mA) 100 kHz 120 Hz Max 100 kHz Max 25C DF ESR Maximum Allowable Ripple Current Moisture Sensitivity (1) To complete KEMET part number, insert M for 20% or K for 10%. Designates capacitance tolerance. (2) To complete KEMET part number, insert T = 100% Matte Tin (Sn) Plated, G = Gold Plated. Designates termination finish. Refer to Ordering Information for additional detail. Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitution will be marked with the higher voltage rating. Substitutions can include better than series. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com Roll Over for Order Info. T2012_T498 * 3/15/2013 5 Tantalum Surface Mount Capacitors - High Temperature T498 150C Rated MnO2 Series Table 1 - Ratings & Part Number Reference cont'd Rated Voltage Rated Case Code/ Cap Case Size KEMET Part Number DC Leakage (See below for part options) T498D106(1)035A(20E700 T498X226(1)035A(2)E500 T498X336(1)035A(2)E500 A +20C Max/5 Min 3.5 7.7 11.6 % @ +20C m @ 20C (mA) 100 kHz 120 Hz Max 100 kHz Max 25C 6.0 700 463 6.0 500 574 6.0 500 574 (mA) 100 kHz 85C 417 517 517 (mA) 100 kHz 125C 185 230 230 Reflow Temp 260C 1 1 1 1.7 5.0 A +20C Max/5 Min 6.0 1100 369 6.0 1000 387 % @ +20C m @ 20C (mA) 100 kHz 120 Hz Max 100 kHz Max 25C 332 348 (mA) 100 kHz 85C 148 155 (mA) 100 kHz 125C 1 1 Reflow Temp 260C DC Leakage VDC F KEMET/EIA 35 35 35 10 22 33 D/7343-31 X/7343-43 X/7343-43 50 50 3.3 10 D/7343-31 D/7343-31 VDC F KEMET/EIA T498D335(1)050A(2)E1K1 T498D106(1)050A(2)E1K0 (See below for part options) Rated Voltage Rated Cap Case Code/ Case Size KEMET Part Number DF DF ESR ESR Maximum Allowable Ripple Current Maximum Allowable Ripple Current Moisture Sensitivity Moisture Sensitivity (1) To complete KEMET part number, insert M for 20% or K for 10%. Designates capacitance tolerance. (2) To complete KEMET part number, insert T = 100% Matte Tin (Sn) Plated, G = Gold Plated. Designates termination finish. Refer to Ordering Information for additional detail. Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitution will be marked with the higher voltage rating. Substitutions can include better than series. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com Roll Over for Order Info. T2012_T498 * 3/15/2013 6 Tantalum Surface Mount Capacitors - High Temperature T498 150C Rated MnO2 Series Recommended Voltage Derating Guidelines 6.3 10 16 20 25 35 50 Working Voltage 85C 6.3 10 16 20 25 35 150C 4.22 6.70 10.72 13.40 16.75 23.45 85C 3.15 5 8 10 12.5 17.5 150C 2.08 3.30 5.28 6.60 8.25 11.55 50 33.50 25 16.50 1.2 1 % Working Voltage Rated Voltage Recommended Application Voltage (for maximum reliability) 0.8 0.6 % Change in Working DC Voltage with Temperature 0.4 Recommended Maximum Application Voltage (As % of Rated Voltage) 67% 33% 0.2 0 -55 25 85 Temperature (C) 125 150 Ripple Current/Ripple Voltage KEMET Series and Case Code EIA Case Code Maximum Power Dissipation (P max) mWatts @ 25C w/+20C Rise A B C D X E T428P S T U V T510X T510E 3216-18 3528-21 6032-28 7343-31 7343-43 7360-38 7360-38 3216-12 3528-12 6032-15 7343-20 7343-43 7360-38 75 85 110 150 165 200 325 60 70 90 125 270 285 25C 1.00 Temperature Compensation Multipliers for Maximum Power Dissipation 85C 0.90 125C 0.40 150C* 0.30 175C** 0.20 T= Environmental Temperature *T498 Only **T499 Only Using the P max of the device, the maximum allowable rms ripple current or voltage may be determined. I(max) = P max/R E(max) = P max*R I = rms ripple current (amperes) E = rms ripple voltage (volts) P max = maximum power dissipation(watts) R = ESR at specified frequency (ohms) (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2012_T498 * 3/15/2013 7 Tantalum Surface Mount Capacitors - High Temperature T498 150C Rated MnO2 Series Reverse Voltage Solid tantalum capacitors are polar devices and may be permanently damaged or destroyed if connected with the wrong polarity. The positive terminal is identified on the capacitor body by a stripe plus in some cases a beveled edge. A small degree of transient reverse voltage is permissible for short periods per the table. The capacitors should not be operated continuously in reverse mode, even within these limits. Temperature Permissible Transient Reverse Voltage 25C 85C 125C 15% of Rated Voltage 5% of Rated Voltage 1% of Rated Voltage Table 2 - Land Dimensions/Courtyard KEMET Metric Size Code Density Level A: Maximum (Most) Land Protrusion (mm) Density Level B: Median (Nominal) Land Protrusion (mm) Density Level C: Minimum (Least) Land Protrusion (mm) Case EIA X Y C V1 V2 X Y C V1 V2 X Y C V1 V2 A 3216-18 1.35 2.15 1.45 6.10 2.80 1.25 1.75 1.35 5.00 2.30 1.15 1.35 1.25 4.10 2.00 B 3528-21 2.35 2.15 1.45 6.10 4.00 2.25 1.75 1.35 5.00 3.50 2.15 1.35 1.25 4.10 3.20 C 6032-28 2.35 2.65 2.60 8.90 4.40 2.25 2.25 2.50 7.80 3.90 2.15 1.85 2.40 6.90 3.60 D 7343-31 2.55 3.75 2.70 10.20 5.50 2.45 3.35 2.60 9.10 5.00 2.35 2.95 2.50 8.20 4.70 X 7343-43 2.55 3.75 2.70 10.20 5.50 2.45 3.35 2.60 9.10 5.00 2.35 2.95 2.50 8.20 4.70 Density Level A: For low-density product applications. Recommended for wave solder applications and provides a wider process window for reflow solder processes. Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reflow solder processes. Density Level C: For high component density product applications. Before adapting the minimum land pattern variations the user should perform qualification testing based on the conditions outlined in IPC Standard 7351 (IPC-7351). Height of these chips may create problems in wave soldering. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2012_T498 * 3/15/2013 8 Tantalum Surface Mount Capacitors - High Temperature T498 150C Rated MnO2 Series Soldering Process Please note that although the X/7343-43 case size can withstand wave soldering, the tall profile (4.3 mm maximum) dictates care in wave process development. Hand soldering should be performed with care due to the difficulty in process control. If performed, care should be taken to avoid contact of the soldering iron to the molded case. The iron should be used to heat the solder pad, applying solder between the pad and the termination, until reflow occurs. Once reflow occurs, the iron should be removed immediately. "Wiping" the edges of a chip and heating the top surface is not recommended. During typical reflow operations, a slight darkening of the goldcolored epoxy may be observed. This slight darkening is normal and not harmful to the product. Marking permanency is not affected by this change. Profile Feature SnPb Assembly Pb-Free Assembly 100C 150C Preheat/Soak Temperature Minimum (TSmin) Temperature Maximum (TSmax) 150C 200C Time (ts) from Tsmin to Tsmax) 60 - 120 seconds 60 - 120 seconds 3C/seconds maximum Ramp-up Rate (TL to TP) 3C/seconds maximum Liquidous Temperature (TL) 183C 217C Time Above Liquidous (t L) 60 - 150 seconds 60 - 150 seconds Peak Temperature (TP) 220C* 235C** 250C* 260C** 20 seconds maximum 30 seconds maximum 6C/seconds maximum 6C/seconds maximum 6 minutes maximum 8 minutes maximum Time within 5C of Maximum Peak Temperature (tP) Ramp-down Rate (TP to TL) Time 25C to Peak Temperature Note: All temperatures refer to the center of the package, measured on the package body surface that is facing up during assembly reflow. *Case Size D, E, P, Y, and X **Case Size A, B, C, H, I, K, M, R, S, T, U, V, W, and Z TP TL Temperature KEMET's families of surface mount capacitors are compatible with wave (single or dual), convection, IR, or vapor phase reflow techniques. Preheating of these components is recommended to avoid extreme thermal stress. KEMET's recommended profile conditions for convection and IR reflow reflect the profile conditions of the IPC/J-STD-020D standard for moisture sensitivity testing. The devices can safely withstand a maximum of three reflow passes at these conditions. tP Maximum Ramp Up Rate = 3C/seconds Maximum Ramp Down Rate = 6C/seconds tL Tsmax Tsmin 25 tS 25C to Peak Time Construction MNO2 /Ta2O5/Ta Silver Adhesive Silver Paint Washer Leadframe (-Cathode) Leadframe (+Anode) Carbon Tantalum Wire Weld (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2012_T498 * 3/15/2013 9 Tantalum Surface Mount Capacitors - High Temperature T498 150C Rated MnO2 Series Capacitor Marking KEMET High Temperature 150C C, D, X Case Sizes HT Polarity Indicator (+) Picofarad Code Date Code* Rated Voltage Date Code* KEMET ID 227 10V KEMET ID Polarity Indicator (+) K 227 10 K 230 Rated Voltage KEMET High Temperature 150C Picofarad Code C6 Internal Code 49 * 230 = 30th week of 2012 Date Code* Date Code * 1 digit = Last number of Year st 2nd and 3rd digit = Week of the Year 9 = 2009 0 = 2010 1 = 2011 2 = 2012 3 = 2013 4 = 2014 01 = 1st week of the Year to 52 = 52nd week of the Year Year Month X = 2009 1 = Jan 7 = Jul A = 2010 2 = Feb 8 = Aug B = 2011 3 = Mar 9 = Spt C = 2012 4 = Apr O = Oct D = 2013 5 = May N = Nov E = 2014 6 = Jun D = Dec Storage Tantalum chip capacitors should be stored in normal working environments. While the chips themselves are quite robust in other environments, solderability will be degraded by exposure to high temperatures, high humidity, corrosive atmospheres, and long term storage. In addition, packaging materials will be degraded by high temperature- reels may soften or warp and tape peel force may increase. KEMET recommends that maximum storage temperature not exceed 40C and maximum storage humidity not exceed 60% relative humidity. Temperature fluctuations should be minimized to avoid condensation on the parts and atmospheres should be free of chlorine and sulphur bearing compounds. For optimized solderability chip stock should be used promptly, preferably within three years of receipt. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2012_T498 * 3/15/2013 10 Tantalum Surface Mount Capacitors - High Temperature T498 150C Rated MnO2 Series Tape & Reel Packaging Information KEMET's molded tantalum and aluminum chip capacitor families are packaged in 8 and 12 mm plastic tape on 7" and 13" reels in accordance with EIA Standard 481-1: Embossed Carrier Taping of Surface Mount Components for Automatic Handling. This packaging system is compatible with all tape-fed automatic pick-and-place systems. 8 mm (0.315") or 12 mm (0.472") Top Tape Thickness 0.10 mm (0.004") Maximum Thickness 180 mm (7.0") or 330 mm (13.0") Table 3 - Packaging Quantity Case Code KEMET I S T M U L W Z V A B C D Y X E/T428P H EIA 3216-10 3216-12 3528-12 3528-15 6032-15 6032-19 7343-15 7343-17 7343-20 3216-18 3528-21 6032-28 7343-31 7343-40 7343-43 7360-38 7360-20 Tape Width (mm) 7" Reel* 13" Reel* 8 8 8 8 12 12 12 12 12 8 8 12 12 12 12 12 12 3,000 2,500 2,500 2,000 1,000 1,000 1,000 1,000 1,000 2,000 2,000 500 500 500 500 500 1,000 12,000 10,000 10,000 8,000 5,000 5,000 3,000 3,000 3,000 9,000 8,000 3,000 2,500 2,000 2,000 2,000 2,500 * No C-Spec required for 7" reel packaging. C-7280 required for 13" reel packaging. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2012_T498 * 3/15/2013 11 Tantalum Surface Mount Capacitors - High Temperature T498 150C Rated MnO2 Series Figure 1 - Embossed (Plastic) Carrier Tape Dimensions P2 T T2 ODo Po [10 pitches cumulative tolerance on tape 0.2 mm] E1 Ao F Ko W B1 E2 Bo S1 P1 T1 Center Lines of Cavity OD 1 Cover Tape B 1 is for tape feeder reference only, including draft concentric about B o. Embossment For cavity size, see Note 1 Table 4 User Direction of Unreeling Table 4 - Embossed (Plastic) Carrier Tape Dimensions Metric will govern Constant Dimensions -- Millimeters (Inches) Tape Size D0 8 mm 12 mm 1.5 +0.10/-0.0 (0.059 +0.004/-0.0) 16 mm D1 Minimum Note 1 1.0 (0.039) 1.5 (0.059) E1 P0 P2 1.75 0.10 (0.069 0.004) 4.0 0.10 (0.157 0.004) 2.0 0.05 (0.079 0.002) R Reference Note 2 25.0 (0.984) 30 (1.181) S1 Minimum Note 3 0.600 (0.024) T Maximum T1 Maximum 0.600 (0.024) 0.100 (0.004) Variable Dimensions -- Millimeters (Inches) Tape Size Pitch 8 mm Single (4 mm) 12 mm Single (4 mm) & Double (8 mm) 16 mm Triple (12 mm) B1 Maximum Note 4 4.35 (0.171) 8.2 (0.323) 12.1 (0.476) E2 Minimum F P1 T2 Maximum W Maximum A0,B0 & K0 6.25 (0.246) 10.25 (0.404) 14.25 (0.561) 3.5 0.05 (0.138 0.002) 5.5 0.05 (0.217 0.002) 5.5 0.05 (0.217 0.002) 4.0 0.10 (0.157 0.004) 8.0 0.10 (0.315 0.004) 8.0 0.10 (0.315 0.004) 2.5 (0.098) 4.6 (0.181) 4.6 (0.181) 8.3 (0.327) 12.3 (0.484) 16.3 (0.642) Note 5 1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and hole location shall be applied independent of each other. 2. The tape, with or without components, shall pass around R without damage (see Figure 5). 3. If S1 < 1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Standard 481-D, paragraph 4.3, section b). 4. B1 dimension is a reference dimension for tape feeder clearance only. 5. The cavity defined by A0, B0 and K0 shall surround the component with sufficient clearance that: (a) the component does not protrude above the top surface of the carrier tape. (b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed. (c) rotation of the component is limited to 20 maximum for 8 and 12 mm tapes and 10 maximum for 16 mm tapes (see Figure 2). (d) lateral movement of the component is restricted to 0.5 mm maximum for 8 mm and 12 mm wide tape and to 1.0 mm maximum for 16 mm tape (see Figure 3). (e) see Addendum in EIA Standard 481-D for standards relating to more precise taping requirements. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2012_T498 * 3/15/2013 12 Tantalum Surface Mount Capacitors - High Temperature T498 150C Rated MnO2 Series Packaging Information Performance Notes 1. Cover Tape Break Force: 1.0 Kg minimum. 2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be: Tape Width Peel Strength 8 mm 0.1 to 1.0 Newton (10 to 100 gf) 12 and 16 mm 0.1 to 1.3 Newton (10 to 130 gf) The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be 165 to 180 from the plane of the carrier tape. During peeling, the carrier and/or cover tape shall be pulled at a velocity of 300 10 mm/minute. 3. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA Standards 556 and 624. Figure 2 - Maximum Component Rotation T Maximum Component Rotation Top View Maximum Component Rotation Side View Typical Pocket Centerline Tape Width (mm) 8,12 16 - 200 Bo Maximum Rotation ( 20 10 T) Typical Component Centerline Ao Figure 3 - Maximum Lateral Movement 8 mm & 12 mm Tape 0.5 mm maximum 0.5 mm maximum 16 mm Tape s Tape Maximum Width (mm) Rotation ( 8,12 20 16 - 56 10 72 - 200 5 S) Figure 4 - Bending Radius Embossed Carrier Punched Carrier 1.0 mm maximum 1.0 mm maximum R Bending Radius (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com R T2012_T498 * 3/15/2013 13 Tantalum Surface Mount Capacitors - High Temperature T498 150C Rated MnO2 Series Figure 5 - Reel Dimensions Full Radius, See Note W3 (Includes Access Hole at Slot Location (O 40 mm minimum) flange distortion at outer edge) W2 (Measured at hub) D A N (See Note) C (Arbor hole diameter) B (see Note) W1 (Measured at hub) If present, tape slot in core for tape start: 2.5 mm minimum width x 10.0 mm minimum depth Note: Drive spokes optional; if used, dimensions B and D shall apply. Table 5 - Reel Dimensions Metric will govern Constant Dimensions -- Millimeters (Inches) Tape Size A B Minimum C D Minimum 8 mm 178 0.20 (7.008 0.008) or 330 0.20 (13.000 0.008) 1.5 (0.059) 13.0 +0.5/-0.2 (0.521 +0.02/-0.008) 20.2 (0.795) 12 mm 16 mm Variable Dimensions -- Millimeters (Inches) Tape Size N Minimum W1 W2 Maximum W3 50 (1.969) 8.4 +1.5/-0.0 (0.331 +0.059/-0.0) 12.4 +2.0/-0.0 (0.488 +0.078/-0.0) 16.4 +2.0/-0.0 (0.646 +0.078/-0.0) 14.4 (0.567) 18.4 (0.724) 22.4 (0.882) Shall accommodate tape width without interference 8 mm 12 mm 16 mm (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2012_T498 * 3/15/2013 14 Tantalum Surface Mount Capacitors - High Temperature T498 150C Rated MnO2 Series Figure 6 - Tape Leader & Trailer Dimensions Embossed Carrier Carrier Tape Punched Carrier 8 mm & 12 mm only END Round Sprocket Holes START Top Cover Tape Elongated Sprocket Holes (32 mm tape and wider) Trailer 160 mm Minimum Components 100 mm Minimum Leader 400 mm Minimum Top Cover Tape Figure 7 - Maximum Camber Elongated sprocket holes (32 mm & wider tapes) Carrier Tape Round Sprocket Holes 1 mm Maximum, either direction Straight Edge 250 mm (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2012_T498 * 3/15/2013 15 Tantalum Surface Mount Capacitors - High Temperature T498 150C Rated MnO2 Series KEMET Corporation World Headquarters Europe Asia Southern Europe Paris, France Tel: 33-1-4646-1006 Northeast Asia Hong Kong Tel: 852-2305-1168 Mailing Address: P.O. Box 5928 Greenville, SC 29606 Sasso Marconi, Italy Tel: 39-051-939111 Shenzhen, China Tel: 86-755-2518-1306 www.kemet.com Tel: 864-963-6300 Fax: 864-963-6521 Central Europe Landsberg, Germany Tel: 49-8191-3350800 Corporate Offices Fort Lauderdale, FL Tel: 954-766-2800 Kamen, Germany Tel: 49-2307-438110 North America Northern Europe Bishop's Stortford, United Kingdom Tel: 44-1279-460122 2835 KEMET Way Simpsonville, SC 29681 Southeast Lake Mary, FL Tel: 407-855-8886 Espoo, Finland Tel: 358-9-5406-5000 Northeast Wilmington, MA Tel: 978-658-1663 Beijing, China Tel: 86-10-5829-1711 Shanghai, China Tel: 86-21-6447-0707 Taipei, Taiwan Tel: 886-2-27528585 Southeast Asia Singapore Tel: 65-6586-1900 Penang, Malaysia Tel: 60-4-6430200 Bangalore, India Tel: 91-806-53-76817 Central Novi, MI Tel: 248-994-1030 West Milpitas, CA Tel: 408-433-9950 Mexico Guadalajara, Jalisco Tel: 52-33-3123-2141 Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of KEMET Electronics Corporation. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2012_T498 * 3/15/2013 16 Tantalum Surface Mount Capacitors - High Temperature T498 150C Rated MnO2 Series Other KEMET Resources Tools Resource Location Configure A Part: CapEdge http://capacitoredge.kemet.com SPICE & FIT Software http://www.kemet.com/spice Search Our FAQs: KnowledgeEdge http://www.kemet.com/keask Electrolytic LifeCalculator http://www.kemet.com:8080/elc Product Information Resource Location Products Technical Resources (Including Soldering Techniques) RoHS Statement Quality Documents http://www.kemet.com/products http://www.kemet.com/technicalpapers http://www.kemet.com/rohs http://www.kemet.com/qualitydocuments Product Request Resource Location Sample Request Engineering Kit Request http://www.kemet.com/sample http://www.kemet.com/kits Contact Resource Location Website Contact Us Investor Relations www.kemet.com http://www.kemet.com/contact http://www.kemet.com/ir Call Us 1-877-MyKEMET Twitter http://twitter.com/kemetcapacitors Disclaimer All product specifications, statements, information and data (collectively, the "Information") are subject to change without notice. All Information given herein is believed to be accurate and reliable, but is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on our knowledge of typical operating conditions for such applications, but are not intended to constitute - and we specifically disclaim - any warranty concerning suitability for a specific customer application or use. This Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by us with reference to the use of our products is given gratis, and we assume no obligation or liability for the advice given or results obtained. Although we design and manufacture our products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated or that other measures may not be required. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2012_T498 * 3/15/2013 17 Tantalum Surface Mount Capacitors - High Temperature T498 150C Rated MnO2 Series Digitally signed by Jeannette Calvo DN: c=US, st=FL, l=Fort Lauderdale, o=KEMET Corp., ou=Marketing Communications, cn=Jeannette Calvo, email=jeannettecalvo@kemet.com Date: 2013.03.26 11:20:23 -04'00' (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2012_T498 * 3/15/2013 18