ORCA
® Series 2
Field-Programmable Gate Arrays
Data Sheet
June 1999
Features
■High -performance, co st-effective, low-power
0.35 µm CMOS technology (OR2CxxA), 0.3 µm CMOS
technology (OR2TxxA), and 0.25 µm CMOS technology
(OR2TxxB), (four-input look-up table (LUT) delay less
than 1.0 ns with -8 speed grade)
■High density (up to 43,200 usable, logic-only gates; or
99,400 gates includin g RAM )
■Up to 480 user I/Os (OR2TxxA and OR2TxxB I/Os are
5 V tolerant to allow interconnection to both 3.3 V and
5 V devices, selectable on a per-pin basis)
■Four 16-bit look-up tables and four latches/flip-flops per
PFU, ni bb le -oriente d for impleme nti ng 4 -, 8-, 16 -, and /or
32-bit (or wider) bus structures
■Eight 3-state buffers per PFU for on-chip bus structures
■Fast, on-chip user SRAM has features to simplify RAM
design and increase RAM speed:
— Asynchronous single port: 64 bits/PFU
— Synchronous single port: 64 bits/PFU
— Synchronous dual port: 32 bits/PFU
■Improved ability to combine PFUs to create larger RAM
structures using write-port enable and 3-state buffers
■Fast, den se m u lti pliers can be cre ated with the mul tip lie r
mode (4 x 1 multiplier/PFU):
— 8 x 8 multiplier requires only 16 PFUs
— 30% increase in speed
■Fli p-flop/latch options t o allow programmable priority of
synchronous set/reset vs. clock enable
■Enhanced cascadable nibble-wide data path
capabi lities for adders , su btrac tor s, counte rs , mu ltipli ers ,
and comparators inclu din g internal fast-carry operation
■Innovative, abundant, and hierarchical nibble-
oriented routing resources that allow automatic u s e of
internal gates for all device densities without sacrificing
performance
■Upward bit stream compatible with the
ORCA
ATT2Cxx/
ATT2T xx series of devices
■Pinout-co mpatible with new
ORCA
Series 3 FPGAs
■TTL or CMOS input levels programmable per pin for the
OR2CxxA (5 V) devices
■Individu ally programmable drive capability:
12 mA sink/6 mA source or 6 mA sink/3 mA source
■Built-in boundary scan (
IEEE
*1149.1 JTAG) and
3-state all I/O pins, (TS_ALL) testability functions
■Multiple configuration options, including simple, low pin-
count s erial ROMs, and pe ripheral or JTA G mo des for in-
system programming (ISP)
■Full PCI bus compliance for all devices
■Supported by industry-standard CAE tools for design
entry, synthesis, and simulation with
ORCA
Foundry
Development System support (for back-end implementa-
tion)
■New, added features (OR2TxxB) have:
— More I/O per package than the OR2TxxA family
— No dedicated 5 V supply (VDD5)
— Faster configuration speed (40 MHz)
— Pin s electab le I/O c lamping di odes pr ov ide 5V o r 3.3V
PCI compli ance and 5V tolerance
— Full PCI bu s comp lianc e in both 5V and 3.3V PCI sys-
tems
*
IEEE
is a registered trademark of The Institute of Electrical and
Electronics Engineers, Inc.
Table 1
. ORCA
Series 2 FPGAs
* The first number in the usable gat es column assumes 48 gates per PFU (12 gates per f our-i nput LUT/FF pair) for logic-only designs. The
second number assumes 30% of a design is RAM. PFUs used as RAM are counted at four gates per bit, with each PFU capable of
implementing a 16 x 4 RAM (or 256 gates) per PFU.
Device Usable
Gates* # LUTs Register s Max User
RAM Bits User
I/Os Array Size
OR2C04A/OR2T04A 4,800—11,000 400 400 6,400 160 10 x 10
OR2C06A/OR2T06A 6,900—15,900 576 576 9,216 192 12 x 12
OR2C0 8A/O R2T08A 9,400—21,600 784 724 12,544 224 14 x 14
OR2C10A/OR2T10A 12,300—28,300 1024 1024 16,384 256 16 x 16
OR2C12A/OR2T12A 15,600—35,800 1296 1296 20,736 288 18 x 18
OR2C15A/OR2T15A/OR2T15B 19,200—44,200 1600 1600 25,600 320 20 x 20
OR2C26A/OR2T26A 27,600—63,600 2304 2304 36,864 384 24 x 24
OR2C40A/OR2T40A/OR2T40B 43,200—99,400 3600 3600 57,600 480 30 x 30
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
2Lucent Technologies Inc.
Table of Contents
Contents Page Contents Page
Features ......................................................................1
Description...................................................................3
ORCA
Foundry Development System Overview.........5
Architecture .................................................................5
Programmable Logic Cells ..........................................5
Programmable Function Unit...................................5
Look-Up Table Operating Modes ............................7
Latches/Flip-Flops .................................................15
PLC Routing Resources........................................17
PLC Architectural Description................................22
Programmable Input/Output Cells.............................25
Inputs.....................................................................25
Outputs..................................................................26
5 V Tolerant I/O (OR2TxxB) ..................................27
PCI Compliant I/O..................................................27
PIC Routing Resources.........................................28
PIC Architectural Description.................................29
PLC-PIC Routing Resources....... ...... ....... ...... .......3 0
Interquad Routing......................................................32
Subquad Routing (OR2C40A/OR2T40A Only)......34
PIC Interquad (MID) Routing.................................36
Programmable Corner Cells......................................37
Programmable Routing..........................................37
Special-Purpose Functions....................................37
Clock Distribution Network ........................................37
Primary Clock........................................................37
Secondary Clock ...................................................38
Selecting Clock Input Pins.....................................39
FPGA States of Operation.........................................40
Initialization............................................................40
Configuration .........................................................41
Start-Up .................................................................42
Reconfiguration .....................................................42
Partial Reconfiguration ..........................................43
Other Configuration Options..................................43
Configuration Data Format........................................43
Using
ORCA
Foundry to Generate
Configuration RAM Data.....................................44
Configuration Data Frame .....................................44
Bit Stream Error Checking.........................................47
FPGA Configuration Modes.......................................47
Master Parallel Mode.............................................47
Master Serial Mode ...............................................48
Asynchrono us Peripheral Mode .. ...... ....... ...... .......4 9
Synchronous Peripheral Mode ..............................49
Slave Serial Mode .................................................50
Slave Parallel Mode...............................................50
Daisy Chain ...........................................................51
Special Function Blocks ............................................52
Single Function Blocks..........................................52
Boundary Scan......................................................54
Boundary-Scan Instructions...................................55
ORCA
Boundary-Scan Circuitry ............................56
ORCA
Timing Characteristics....................................60
Estimating Power Dissipation....................................61
OR2CxxA...............................................................61
OR2TxxA ...............................................................63
OR2T15B and OR 2T40B... ...... ....... ...... ....... ...... ....65
Pin Information .. ....... ...... ....... ...... ....... ...... ....... ...... ....66
Pin Descriptio ns.... ...... ....... ...... ....... ...... ....... ...... ....66
Package Compatibility ...........................................68
Compatibility with Series 3 FPGAs........................70
Package Thermal Characteristics............................126
QJA......................................................................126
yJC.......................................................................126
QJC......................................................................126
QJB......................................................................126
Package Coplanarity ...............................................127
Package Parasitics..................................................127
Absolute Maximum Ratings.....................................129
Recommended Operating Conditions......................129
Electrical Characteristics .........................................130
Timing Characteristics.............................................132
Series 2................................................................160
Measurement Conditions.........................................169
Output Buffer Characteristics...................................170
OR2CxxA.............................................................170
OR2TxxA .............................................................171
OR2TxxB .............................................................172
Package Outline Drawings ......................................173
Terms and Definitions..........................................173
84-Pin PLCC........................................................174
100-Pin TQFP......................................................175
144-Pin TQFP......................................................176
160-Pin QFP........................................................177
208-Pin SQFP......................................................178
208-Pin SQFP2....................................................179
240-Pin SQFP......................................................180
240-Pin SQFP2....................................................181
256-Pin PBGA .....................................................182
304-Pin SQFP......................................................183
304-Pin SQFP2....................................................184
352-Pin PBGA .....................................................185
432-Pin EBGA .....................................................186
Ordering Information................................................187
Index........................................................................189
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 3
Description
The
ORCA
Series 2 series of SR AM-bas ed FPGAs are
an enhanced version of the ATT2C/2T architecture.
The latest
ORCA
series includes patented architectural
enhancements that make functions f aster and easier to
design while conserving the use of PLCs and routing
resources.
The Series 2 devices can be used as drop-in replace-
ments for the ATT2Cxx/ATT2Txx series, respectively,
and they are also bit stream compatible with each
other. The usable gate counts associated with each
series are provided in Table 1. Both series are offered
in a variety of packages, speed grades, and tempera-
ture ranges.
The
ORCA
series FPGA consists of two basic ele-
ments: programmable logic cells (PLCs) and program-
mable input/output cells (PICs). An array of PLCs is
surrounded by PICs as shown in Figure 1. Each PLC
contains a programmable function unit (PFU). The
PLCs and PICs also contain routing resources and
configuration RAM. All logic is done in the PFU. Each
PFU contains f our 16-bit look-up tables (LUTs) and f our
latches/flip-flops (FFs).
The PLC architecture provides a balanced mix of logic
and routing that allows a higher utilized gate/PFU than
alternative architectures. The routing resources carry
logic signals between PFUs and I/O pads. The routing
in the PLC is symmetrical about the horizontal and ver-
tical axes. This improv es routability b y allowing a b us of
signals to be routed into the PLC from any direction.
Some examples of the resources required and the per-
f ormance t hat ca n be ac hie v ed using t hese de vices ar e
represented in Table 2.
Table 2
. ORCA
Series 2 System Performance
1. Implemented using 4 x 1 multipli er mode (unpipelined), register-to-register, two 8-bit inputs, one 16-bit output.
2. Implemented using two 16 x 12 ROMs and one 12-bit adder, one 8-bit input, one fixed operand, one 16-bit output.
3. Implemented using 4 x 1 multiplier mode (fully pipelined), tw o 8-bit inputs , one 16-bit output (28 of 44 PFUs contain only pi peli ning registers).
4. Implemented using 16 x 4 synchronous single-port RAM mode allowing both read and wr ite per clock cycle, including write/read address
multiplexer.
5. Implemented using 16 x 4 synchronous single-port RAM mode allowing either read or write per clock cycle , including write/read address mul-
tiplexer.
6. Implemented using 16 x 2 synchronous dual-port RAM mode.
7. OR2TxxB available only in -7 and -8 speeds only.
8. Speed grades of -5, -6, and -7 are for OR2TxxA devices only.
Function #
PFUs Speed Grade Unit
-2A -3A -4A -5A -6A -7A -7B -8B
16-bit loadable up/down
counter 4 51.0 66.7 87.0 104.2 129.9 144.9 131.6 149.3 MHz
16-bit accumulator 4 51.0 66.7 87.0 104.2 129.9 144.9 131.6 149.3 MHz
8 x 8 parallel multiplier:
— Multiplier mode, unpipelined1
— ROM mode, unpipelined2
— Multiplier mode, pipelined3
22
9
44
14.2
41.5
50.5
19.3
55.6
69.0
25.1
71.9
82.0
31.0
87.7
103.1
36.0
107.5
125.0
40.3
122.0
142.9
37.7
103.1
123.5
44.8
120.5
142.9
MHz
MHz
MHz
32 x 16 RAM:
— Single port (read and write/
cycle)4
— Single port5
— Dual port6
9
9
16
21.8
38.2
38.2
28.6
52.6
52.6
36.2
69.0
83.3
53.8
92.6
92.6
53.8
92.6
92.6
62.5
96.2
96.2
57.5
97.7
97.7
69.4
112.4
112.4
MHz
MHz
MHz
36-bit parity check (internal) 4 13.9 11.0 9.1 7.4 5.6 5.2 6.1 5.1 ns
32-bit address decode
(internal) 3.25 12.3 9.5 7.5 6.1 4.6 4.3 4.8 4.0 ns
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
4Lucent Technologies Inc.
Description (continued)
The FPGA’s functionality is determined by internal configuration RAM. The FPGA’s internal initialization/configura-
tion circuitry loads the configuration data at powerup or under system control. The RAM is loaded by using one of
several configuration modes. The configuration data resides externally in an EEPROM, EPROM, or ROM on the
circuit board, or any other storage media. Serial ROMs provide a simple, low pin count method for configuring
FPGAs, while the peripheral and JTAG configuration modes allow for easy, in-system programming (ISP).
5-6779(F)
Figure 1. Series 2 Array
PL9 PL8 PL7 PL6 PL5 PL4 PL3 PL2 PL1PL13 PL12 PL11
PR12PR11PR9PR8PR7PR6PR5PR4PR3PR2PR1 PR13 PR18PR17PR16PR15PR14RMIDPR10
PT1 PT2 PT3 PT4 PT5 PT6 PT7 PT8 PT9 PT11 PT12
R1C1 R1C2 R1C3 R1C4 R1C5 R1C6 R1C7 R1C8 R1C9 R1C10 R1C18R1C17R1C16R1C15R1C14R1C13R1C12R1C11
PT13 PT14 PT15 PT16 PT17 PT18
PB1 PB2 PB3 PB4 PB5 PB6 PB7 PB8 PB9 PB10 PB11 PB12
PL18 PL17 PL16 PL15 PL14
PB13 PB14 PB15 PB16 PB17 PB18
PL10
BMID
PT10
vIQ
R2C1 R2C2 R2C3 R2C4 R2C5 R2C6 R2C7 R2C8 R2C9 R2C10
R3C1 R3C2 R3C3 R3C4 R3C5 R3C6 R3C7 R3C8 R3C9 R3C10
R4C1 R4C2 R4C3 R4C4 R4C5 R4C6 R4C7 R4C8 R4C9 R4C10
R5C1 R5C2 R5C3 R5C4 R5C5 R5C6 R5C7 R5C8 R5C9 R5C10
R6C1 R6C2 R6C3 R6C4 R6C5 R6C6 R6C7 R6C8 R6C9 R6C10
R7C1 R7C2 R7C3 R7C4 R7C5 R7C6 R7C7 R7C8 R7C9 R7C10
R8C1 R8C2 R8C3 R8C4 R8C5 R8C6 R8C7 R8C8 R8C9 R8C10
R9C1 R9C2 R9C3 R9C4 R9C5 R9C6 R9C7 R9C8 R9C9 R9C10
R10C1 R10C2 R10C3 R10C4 R10C5 R10C6 R10C7 R10C8 R10C9 R10C10
R2C18R2C17R2C16R2C15R2C14R2C13R2C12R2C11
R3C18R3C17R13C16R3C15R3C14R3C13R3C12R3C11
R4C18R4C17R4C16R4C15R4C14R4C13R4C12R4C11
R5C18R5C17R5C16R5C15R5C14R5C13R5C12R5C11
R6C18R6C17R6C16R6C15R6C14R6C13R6C12R6C11
R7C18R7C17R7C16R7C15R7C14R7C13R7C12R7C11
R8C18R8C17R8C16R8C15R8C14R8C13R8C12R8C11
R9C18R9C17R9C16R9C15R9C14R9C13R9C12R9C11
R10C18R10C17R10C16R10C15R10C14R10C13R10C12R10C11
R18C18R18C17R18C16R18C15R18C14R18C13R18C12R18C11
R17C18R17C17R17C16R17C15R17C14R17C13R17C12R17C11
R16C18R16C17R16C16R16C15R16C14R16C13R16C12R16C11
R15C18R15C17R15C16R15C15R15C14R15C13R15C12R15C11
R14C18R14C17R14C16R14C15R14C14R14C13R14C12R14C11
R13C18R13C17R13C16R13C15R13C14R13C13R13C12R13C11
R12C18R12C17R12C16R12C15R12C14R12C13R12C12R12C11
R11C18R11C17R11C16R11C15R11C14R11C13R11C12R11C11
R18C10R18C9R18C8R18C7R18C6R18C5R18C4R18C3R18C2R18C1
R17C10R17C9R17C8R17C7R17C6R17C5R17C4R17C3R17C2R17C1
R16C10R16C9R16C8R16C7R16C6R16C5R16C4R16C3R16C2R16C1
R15C10R15C9R15C8R15C7R15C6R15C5R15C4R15C3R15C2R15C1
R14C10R14C9R14C8R14C7R14C6R14C5R14C4R14C3R14C2R14C1
R13C10R13C9R13C8R13C7R13C6R13C5R13C4R13C3R13C2R13C1
R12C10R12C9R12C8R12C7R12C6R12C5R12C4R12C3R12C2R12C1
R11C10R11C9R11C8R11C7R11C6R11C5R11C4R11C3R11C2R11C1
hIQ
TMID
LMID
Lucent Technologies Inc. 5
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
ORCA
Foundr y Development System
Overview
The
ORCA
F oundry Dev elopment System interfaces to
front-end design entry tools and provides the tools to
produce a configured FPGA. In the design flow, the
user defines the functionality of the FPGA at two
points: at design entry and at the bit stream generation
stage.
F ollowing design entry, the de velopment system’ s map ,
place, and route tools translate the netlist into a routed
FPGA. Its bit stream generator is then used to generate
the configuration data which is loaded into the FPGA’s
internal configuration RAM. When using the bit stream
generator, the user selects options that affect the func-
tionality of the FPGA. Combined with the front-end
tools,
ORCA
Foundry produces configuration data that
implements the various logic and routing options dis-
cussed in this data sheet.
Architecture
The
ORCA
Series FPGA is comprised of two basic
elements: PLCs and PICs. Figure 1 shows an array of
programmable logic cells (PLCs) surrounded by pro-
grammable input/output cells (PICs). The Series 2 has
PLCs arranged in an array of 20 r ows and 20 columns.
PICs are located on all f our sides of the FPGA between
the PLCs and the IC edge.
The location of a PLC is indicated by its row and col-
umn so that a PLC in the second row and third column
is R2C3. PICs are indicated similarly, with PT (top) and
PB (bottom) designating rows and PL (left) and PR
(right) designating columns, f ollowed by a number. The
routing resources and configuration RAM are not
shown, but the interquad routing blocks (hIQ, vIQ)
present in the Series 2 series are shown.
Each PIC contains the necessary I/O buffers to inter-
face to bond pads. The PICs also contain the routing
resources needed to connect signals from the bond
pads to/from PLCs. The PICs do not contain any user-
accessible logic elements, such as flip-flops.
Combinatorial logic is done in look-up tables (LUTs)
located in the PFU. The PFU can be used in different
modes to meet different logic requirements. The LUT’s
configurable medium-/large-grain architecture can be
used to implement from one to four combinatorial logic
functions. The fle xibility of the LUT to handle wide input
functions, as well as multiple smaller input functions,
maximizes the gate count/PFU.
The LUTs can be programmed to operate in one of
three modes: combinatorial, ripple, or memory. In com-
binatorial mode, the LUTs can realize any four-, five-,
or six-input logic functions. In ripple mode, the high-
speed carry logic is used for arithmetic functions, the
new multiplier function, or the enhanced data path
functions. In memory mode, the LUTs can be used as a
16 x 4 read/write or read-only memory (asynchronous
mode or the new synchronous mode) or a ne w 16 x 2
dual-po rt memory.
Programmable Logic Cells
The programmable logic cell (PLC) consists of a pro-
grammable function unit (PFU) and routing resources.
All PLCs in the arra y are identical. The PFU, which con-
tains four LUTs and fo ur latches/FFs for logic imple-
mentation, is discussed in the next section.
Programmable Function Unit
The PFUs are used for logic. Each PFU has 19 exter-
nal inputs and six outputs and can operate in several
modes. The functionality of the inputs and outputs
depends on the operating mode.
The PFU uses three input data buses (A[4:0], B[4:0],
WD[3:0]), four control inputs (C0, CK, CE, LSR), and a
carry input (CIN); the last is used for fast arithmetic
functions. There is a 5-bit output bus (O[4:0]) and a
carry-out (COUT).
5-2750(F).r3
Figure 2. PFU Ports
PR OGRAMMABLE LOGIC CELL (PLC)
WD3
WD2
WD1
WD0
A4
A3
A2
A1
A0
B4
B3
B2
B1
B0
O4
O3
O2
O1
O0
PROGRAMMABLE
FUNCTION UNIT
CE LSRC0 CK
(ROUTING RE SOURCE S, CONFIGURATION RAM)
CIN
(PFU)
COUT
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
6Lucent Technologies Inc.
Programmable Logic Cells (continued))
Key: C = controlled by configuration RAM.
Figure 3. Simplified PFU Diagram
5-4573(F)
A4
A3
A2
A1
A4
A3
A2
A1
QLUT3
A0
CARRY
CARRY
A3
A2
A1
A0
QLUT2
B4
B3
B2
B1
B4
B3
B2
B1
QLUT1
B0
CARRY
CARRY
B3
B2
B1
B0
QLUT0
CIN
C0
LSR
GSR
WD[3:0]
CK
CKEN
TRI
PFU_XOR
B4
A4
PFU_NAND
PFU_MUX
C
C
C C
WD3
WD2
WD1
WD0
C
CC
T
T
T
T
REG3
SR EN
REG2
SR EN
REG1
SR EN
REG0
SR EN
O4
O3
O2
O1
O0
F3
C
C
COUT
F2
F1
F0
D0
D1
D2
D3
Q0
Q1
Q2
Q3
C
T
T
T
T
C
Figure 2 and Figure 3 show high-level and detailed
views of the ports in the PFU, respectively. The ports
are referenced with a two- to four-character suffix to a
PFU’s location. As mentioned, there are two 5-bit input
data buses (A[4:0] and B[4:0]) to the LUT, one 4-bit
input data bus (WD[3:0]) to the latches/FFs, and an
output data bus (O[4:0]).
Figure 3 sho ws the four latches/FFs (REG[3:0]) and the
64-bit look-up table (QLUT[3:0]) in the PFU. The PFU
does combinatorial logic in the LUT and sequential
logic in the latches/FFs. The LUT is static random
access memory (SRAM) and can be used for read/
write or read-only memory. The eight 3-state buffers
found in each PLC are also shown, although they actu-
ally reside external to the PFU.
Each latch/FF can accept data from the LUT. Alterna-
tively, the latches/FFs can accept direct data from
WD[3:0], eliminating the LUT delay if no combinatorial
function is needed. The LUT outputs can bypass the
latches/FFs, which reduces the delay out of the PFU . It
is possible to use the LUT and latches/FFs more or
less independently. F or example, the latches/FFs can
be used as a 4-bit shift register, and the LUT can be
used to detect when a register has a particular pattern
in it.
Lucent Technologies Inc. 7
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Programmable Logic Cells (continued)
Tab le 3 lists the basic operating modes of the LUT. The
operating mode affects the functionality of the PFU
input and output ports and internal PFU routing. For
e xample, in some operating modes, the WD[3:0] inputs
are direct data inputs to the PFU latches/FFs. In the
dual 16 x 2 memory mode, the same WD[3:0] inputs
are used as a 4-bit data input bus into LUT memory.
The PFU is used in a variety of modes, as illustrated in
Figures 4 through 11, and it is these specific modes
that are most relevant to PFU functionality.
PFU Control Inputs
The four control inputs to the PFU are cloc k (CK), local
set/reset (LSR), clock enable (CE), and C0. The CK,
CE, and LSR inputs control the operation of all four
latches in the PFU. An active-low global set/reset
(GSRN) signal is also available to the latches/FFs in
every PFU. Their operation is discussed briefly here,
and in more detail in the Latches/Flip-Flops section.
The polarity of the control inputs can be inverted.
The CK input is distrib uted to each PFU from a vertical
or horizontal net. The CE input inhibits the latches/FFs
from responding to data inputs. The CE input can be
disabled, always enabling the clock. Each latch/FF can
be independently programmed to be set or reset by the
LSR and the global set/reset (GSRN) signals. Each
PFU’s LSR input can be configured as synchronous or
asynchronous. The GSRN signal is always asynchro-
nous. The LSR signal applies to all four latches/FFs in
a PFU. The LSR input can be disabled (the default).
The asynchronous set/reset is dominant over clocked
inputs.
The C0 input is used as an input into the special PFU
gates for wide functions in combinatorial logic mode.
In the memory modes, this input is also used as the
write-port enable input. The C0 input can be disabled
(the default).
Look-Up Table Operating Modes
The look-up table (LUT) can be configured to operate
in one of three general modes:
■Combinatorial logic mode
■Ripple mode
■Memory mode
The combinatorial logic mode uses a 64-bit look-up
table to implement Boolean functions. The two 5-bit
logic inputs, A[4:0] and B[4:0], and the C0 input are
used as LUT inputs. The use of these ports changes
based on the PFU operating mode.
The functionality of the LUT is determined b y its operat-
ing mode. The entries in Table 3 show the basic modes
of operation for combinatorial logic, ripple, and memory
functions in the LUT. Depending on the operating
mode, the LUT can be divided into sub-LUTs. The LUT
is comprised of two 32-bit half look-up tables, HLUTA
and HLUTB. Each half look-up table (HLUT) is com-
prised of two quarter look-up tables (QLUTs). HLUTA
consists of QLUT2 and QLUT3, while HLUTB consists
of QLUT0 and QLUT1. The outputs of QLUT0, QLUT1,
QLUT2, and QLUT3 are F0, F1, F2, and F3, respec-
tively.
Table 3. Look-Up Table Operating Modes
F or combinatorial logic, the LUT can be used to do any
single function of six inputs, any two functions of five
inputs, or four functions of f our inputs (with some inputs
shared), and three special functions based on the two
five-input functions and C0.
Mode Function
F4A Two functions of four inputs, some inputs
shared (QLUT2/Q LUT3)
F4B Two functions of four inputs, some inputs
shared (QLUT0/Q LUT1)
F5A One function of five inputs (HLUTA)
F5B One function of five inputs (HLUTB)
R 4-bit ripple (LUT)
MA 16 x 2 asynchronous memory (HLUTA)
MB 16 x 2 asynchronous memory (HLUTB)
SSPM 16 x 4 synchronous single-port memory
SDPM 16 x 2 synchronous dual-port memory
8Lucent Technologies Inc.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
Programmable Logic Cells (continued)
The LUT ripple mode operation offers standard arith-
metic functions, such as 4-bit adders, subtractors,
adder/subtractors, and counters. In the
ORCA
Series 2, there are two new ripple modes available.
The first new mode is a 4 x 1 multiplier, and the second
is a 4-bit compar ator. These new modes offer the
advantages of faster speeds as well as denser logic
capabilities.
When the LUT is configured to operate in the memory
mode, a 16 x 2 asynchronous memory fits into an
HLUT. Both the MA and MB modes were av ailable in
previous
ORCA
architectures, and each mode can be
configured in an HLUT separately. In the Series 2,
there are two ne w memory modes availab le. The first is
a 16 x 4 synchronous single-port memory (SSPM), and
the second is a 16 x 2 synchronous dual-port memory
(SDPM). These new modes offer easier implementa-
tion, faster speeds, denser RAMs, and a dual-port
capability that wasn’t previously offered as an option in
the ATT2Cxx/ ATT2Txx families.
If the LUT is configured to operate in the ripple mode, it
cannot be used f or basic combinatorial logic or memory
functions. In modes other than the ripple, SSPM, and
SDPM modes, combinations of operating modes are
possible. For example, the LUT can be configured as a
16 x 2 RAM in one HLUT and a five-input combinatorial
logic function in the second HLUT. This can be done b y
configuring HLUTA in the MA mode and HLUTB in the
F5B mode (or vice versa).
F4A/F4B Mode—Two Four -Input Functions
Each HLUT can be used to implement two four-input
combinatorial functions, but the total number of inputs
into each HLUT cannot exceed five. The two QLUTs
within each HLUT share three inputs. In HLUTA, the
A1, A2, and A3 inputs are shared by QLUT2 and
QLUT3. Similarly, in HLUTB, the B1, B2, and B3 inputs
are shared by QLUT0 and QLUT1. The four outputs
are F0, F1, F2, and F3. The results can be routed to
the D0, D1, D2, and D3 latch/FF inputs or as an output
of the PFU. The use of the LUT for four functions of up
to four inputs each is given in Figure 4.
F5A/F5B Mode—One Five-Input Variable Function
Each HLUT can be used to implement any five-input
combinatorial function. The input ports are A[4:0] and
B[4:0], and the output ports are F0 and F3. One five or
less input function is input into A[4:0], and the second
five or less input function is input into B[4:0]. The
results are routed to the latch/FF D0 and latch/FF D3
inputs, or as a PFU output. The use of the LUT for two
independent functions of up to five inputs is shown in
Figure 5. In this case, the LUT is configured in the F5A
and F5B modes. As a variation, the LUT can do one
function of up to five input variables and two four-input
functions using F5A and F4B modes or F4A and F5B
modes.
5-2753(F).r2
Figure 4. F4 Mode—Four Functions of Four-
Input Variables
5-2845(F).r2
Figure 5. F5 Mode—Two Functions of Five-Input
Variables
QLUT2
A3 A3
A2
A1
A0
A2
A1
A0
F2
QLUT3
A4 A4
A3
A2
A1
A3
A2
A1
F3
HLUTA
QLUT0
B3 B3
B2
B1
B0
B2
B1
B0
F0
QLUT1
B4 B4
B3
B2
B1
B3
B2
B1
F1
HLUTB
QLUT3
QLUT2
F3
QLUT1
QLUT0
B4
B3
B2
B1
B0
F0
WEA
A3
A2
A1
A0
B4
B3
B2
B1
B0
A4
A3
A2
A1
A0
HLUTA
HLUTB
c0
WPE
WD3
WD2
WD3
WD2
F2
Lucent Technologies Inc. 9
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Programmable Logic Cells (continued)
F5M and F5X Modes—Special Function Modes
The PFU contains logic to implement two special func-
ti on modes which are variations on the F5 mode. As
with the F5 mode, the LUT implements two indepen-
dent five-input functions. Figure 6 and Figure 7 show
the schematics for F5M and F5X modes, respectively.
The F5X and F5M functions differ from the basic F5A/
F5B functions in that there are three logic gates which
have inputs from the two 5-input LUT outputs. In some
cases, this can be used for faster and/or wider logic
functions.
As can be seen, two of the three inputs into the NAND,
XOR, and MUX gates, F0 and F3, are from the LUT.
The third input is from the C0 input into PFU. Since the
C0 input bypasses the LUTs, it has a much smaller
delay through the PFU than for all other inputs into the
special PFU gates. This allows multiple PFUs to be
cascaded together while reducing the delay of the criti-
cal path through the PFUs. The output of the first spe-
cial function (either XOR or MUX) is F1. Since the XOR
and MUX share the F1 output, the F5X and F5M
modes are mutually exclusive . The output of the NAND
PFU gate is F2 and is always available in either mode.
To use either the F5M or F5X functions, the LUT must
be in the F5A/F5B mode; i.e., only 5-input LUTs
allowed. In both the F5X and F5M functions, the out-
puts of the five-input combinatorial functions, F0 and
F3, are also usable simultaneously with the special
PFU gate outputs.
The output of the MUX is:
F1 = (HLUTA & C0) + (HLUTB & C0)
F1 = (F3 & C0) + (F0 & C0)
The output of the exclusive OR is:
F1 = HLUTA ⊕ HLUTB ⊕ C0
F1 = F3 ⊕ F0 ⊕ C0
The output of the NAND is:
F2 = HLUTA & HLUTB & C0
F2 = F3 & F0 & C0
5-2754(F).r3
Figure 6. F5M Mode—Multiplex ed Function of T w o
Independent Five-Input Variable
Functions
5-2755(F).r2
Figure 7. F5X Mode—Exclusive OR Function of Two
Independent Five-Input Variable
Functions
QLUT3
QLUT2
A4 A4
A3
A2
A1
A0
A3
A2
A1
A0
QLUT1
QLUT0
B4 B4
B3
B2
B1
B0
B3
B2
B1
B0
C0
F3
F0 F1
F0
F2
F3
A4 A4
A3
A2
A1
A0
A3
A2
A1
A0
B4 B4
B3
B2
B1
B0
B3
B2
B1
B0
C0
F3
F0
F1
F0
F2
F3
HLUTA
HLUTB
10 Lucent Technologies Inc.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
Programmable Logic Cells (continued)
5-2751(F).r3
Figure 8. F5M Mode—One Six-Input Variable
Function
F5M Mode—One Six-Input Variable Function
The LUT can be used to implement any function of six-
input variables. As shown in Figure 8, fiv e input signals
(A[4:0]) are routed into both the A[4:0] and B[4:0] ports,
and the C0 port is used for the sixth input. The output
port is F1.
Ripple Mode
The LUT can do nibble-wide ripple functions with high-
speed carry logic. Each QLUT has a dedicated carry-
out net to route the carry to/from the adjacent QLUT.
Using the internal carry circuits, fast arithmetic and
counter functions can be implemented in one PFU.
Similarly, each PFU has carry-in (CIN) and carry-out
(COUT) ports for fast-carry routing between adjacent
PFUs.
The ripple mode is generally used in operations on two
4-bit buses. Each QLUT has two operands and a ripple
(generally carry) input, and provides a result and ripple
(generally carry) output. A single bit is rippled from the
previous QLUT and is used as input into the current
QLUT. F or QLUT0, the ripple input is from the PFU CIN
port. The CIN data can come from either the fast-carry
routing or the PFU input B4, or it can be tied to logic 1
or logic 0.
The resulting output and ripple output are calculated by
using generate/propagate circuitry. In ripple mode, the
two operands are input into A[3:0] and B[3:0]. The four
result bits, one per QLUT, are F[3:0] (see Figure 9).
The ripple output from QLUT3 can be routed to dedi-
cated carry-out circuitry into any of four adjacent PLCs,
or it can be placed on the O4 PFU output, or both. This
allows the PLCs to be cascaded in the ripple mode so
that nibble-wide ripple functions can be expanded eas-
ily to any length.
5-2756(F).r32
Figure 9. Ripple Mode
The ripple mode can be used in one of four submodes.
The first of these is adder/subtractor mode. In this
mode, each QLUT generates two separate outputs.
One of the two outputs selects whether the carry-in is
to be propagated to the carry-out of the current QLUT
or if the carry-out needs to be generated. The result of
this selection is placed on the carry-out signal, which is
connected to the next QLUT or the COUT signal, if it is
the last QLUT (QLUT3).
The other QLUT output creates the result bit for each
QLUT that is connected to F[3:0]. If an adder/subtractor
is needed, the control signal to select addition or sub-
traction is input on A4. The result bit is created in one-
half of the QLUT from a single bit from each input bus,
along with the ripple input bit. These inputs are also
used to create the programmable propagate.
QLUT3
QLUT2
A4 A4
A3
A2
A1
A0
A3
A2
A1
A0
QLUT1
QLUT0
B4 B4
B3
B2
B1
B0
B3
B2
B1
B0
C0
F3
F0
F1
QLUT3
B3
B3 A3
A3 F3
QLUT2
B2
B2 A2
A2 F2
QLUT1
B1
B1 A1
A1 F1
QLUT0
B0
B0 A0
A0 F0
CIN
CIN
COUT
COUT
Lucent Technologies Inc. 11
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Programmable Logic Cells (continued)
The second submode is the counter submode (see
Figure 10). The present count is supplied to input
A[3:0], and then output F[3:0] will either be incre-
mented by one for an up counter or decremented by
one for a down counter. If an up counter or down
counter is needed, the control signal to select the direc-
tion (up or down) is input on A4. Generally, the latches/
FFs in the same PFU are used to hold the present
count value.
5-4643(F).r1
Figure 10. Counter Submode with Flip-Flops
In the third submode, multiplier submode, a single
PFU can affect a 4 x 1-bit multiply and sum with a par-
tial product (see Figure 11). The multiplier bit is input at
A4, and the multiplicand bits are input at B[3:0], where
B3 is th e mo st sign ifi cant bit (M SB). A[ 3:0] con tai ns t he
partial product (or other input to be summed) from a
previous stage. If A4 is logical 1, the multiplicand is
added to the partial product. If A4 is logical zero , z ero is
added to the partial product, which is the same as
passing the partial product. CIN can hold the carry-in
from the less significant PFUs if the multiplicand is
wider than 4 bits, and COUT holds any carry-out from
the addition, which may then be used as part of the
product or routed to another PFU in multiplier mode for
multiplicand width expansion.
Figure 11. Multiplier Submode
Ripple mode’s fourth submode features equality
comparators, where one 4-bit bus is input on B[3:0],
another 4-bit bus is input on B[3:0], and the carry-in is
tied to 0 inside the PFU. The carry-out (¦) signal will be
0 if A = B or will be 1 if A ¦ B. If larger than 4 bits, the
carry-out (¦) signal can be cascaded using fast-carry
logic to the carry-in of any adjacent PFU. Comparators
for greater than or equal or less than (>, =, <) continue
to be supported using the ripple mode subtractor. The
use of this submode could be shown using Figure 9
with CIN tied to 0.
DQ
COUT
LUT
A3 QLUT3 F3 Q3
COUT
DQ
A2 QLUT2 F2 Q2
DQ
A1 QLUT1 F1 Q1
DQ
A0 QLUT0 F0 Q0
CIN
CIN
+
10
A3 B3
0
A4
COUT
F3
+
A2 B2
F2
+
A1 B1
F1
+
A0 B0
F0
CIN
10
0
10
0
10
0
5-4620(F)
12 Lucent Technologies Inc.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
Programmable Logic Cells (continued)
Asynchronous Memory Modes—MA and MB
The LUT in the PFU can be configured as either read/
write or read-only memory. A read/write address
(A[3:0], B[3:0]), write data (WD[1:0], WD[3:2]), and two
write-enable (WE) ports are used for memory. In asyn-
chronous memory mode, each HLUT can be used as a
16 x 2 memory. Each HLUT is configured indepen-
dently, allowing functions such as a 16 x 2 memory in
one HLUT and a logic function of fiv e input v ariables or
less in the other HLUT.
Figure 12 illustrates the use of the LUT for a 16 x 4
memory. When the LUTs are used as memory, there
are independent address, input data, and output data
buses. If the LUT is used as a 16 x 4 read/write mem-
ory, the A[3:0] and B[3:0] ports are address inputs
(A[3:0]). The A4 and B4 ports are write-enable (WE)
signals. The WD[3:0] inputs are the data inputs. The
F[3:0] data outputs can be routed out on the O[4:0]
PFU outputs or to the latch/FF D[3:0] inputs.
5-2757(F).r3
Figure 12. MA/MB Mode—16 x 4 RAM
To increase memory word depth above 16 (e.g., 32 x
4), two or more PLCs can be used. The address and
write data inputs for the two or more PLCs are tied
together (bit by bit), and the data outputs are routed
through the f our 3-statable BIDIs available in each PFU
and are then tied together (bit by bit).
The control signal of the 3-statable BIDIs, called a RAM
bank-enable, is created from a decode of upper
address bits. The RAM bank-enable is then used to
enable 4 bits of data from a PLC onto the read data
bus.
The
ORCA
Series 2 series also has a new AND func-
tion av ailable f or each PFU in RAM mode. The inputs to
this function are the write-enable (WE) signal and the
write-port enable (WPE) signal. The write-enable sig-
nal is A4 for HLUTA and B4 for HLUTB, while the other
input into the AND gates for both HLUTs is the write-
port enable, input on C0 or CIN. Generally, the WPE
input is driven by the same RAM bank-enable signal
that controls the BIDIs in each PFU.
The selection of which RAM bank to write data into
does not require the use of LUTs from other PFUs, as
in pr e vi ous
ORCA
architectures. This reduces the num-
ber of PFUs required for RAMs larger than 16 words in
depth. Note that if either HLUT is in MA/MB mode, then
the same WPE is active for both HLUTs.
To increase the memory’s word size (e.g., 16 x 8), two
or more PLCs are used again. The address, write-
enable, and write-port enable of the PLCs are tied
together (bit by bit), and the data is different for each
PLC. Increasing both the address locations and word
size is done by using a combination of these two tech-
niques.
The LUT can be used simultaneously for both memory
and a combinatorial logic function. Figure 13 shows the
use of a LUT implementing a 16 x 2 RAM (HLUTA) and
any function of up to five input variables (HLUTB).
5-2845(F).a.r1
Figure 13. MA/F5 Mode—16 x 2 Memory and One
Function of Five Input Variables
A3 A3
A2
A1
A0
WD3
A2
A1
A0
WD3
F3
F2
WD2WD2
WD1
WD0
B3
B2
B1
WD0
B3
B2
B1
F1
F0
B0B0
WD1
A4
B4
WEA
WEB
HLUTA
HLUTB
WPE
C0
C0 QLUT3
QLUT2
F3
QLUT1
QLUT0
B4
B3
B2
B1
B0
F0
WEA
A3
A2
A1
A0
B4
B3
B2
B1
B0
A4
A3
A2
A1
A0
HLUTA
HLUTB
F2
WD3
WPE
WD3 C0
Lucent Technologies Inc. 13
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Programmable Logic Cells (continued)
Synchronous Memory Modes—SSPM and SDPM
The MA/MB asynchronous memory modes described
previously allow the PFU to perf orm as a 16 x 4
(64 bits) single-port RAM. Synchronously writing to this
RAM requires the write-enable control signal to be
gated with the clock in another PFU to create a write
pulse. To simplify this functionality, the Series 2 de vices
contain a synchronous single-port memory (SSPM)
mode, where the generation of the write pulse is done
in each PFU.
With SSPM mode, the entire LUT becomes a 16 x 4
RAM, as shown in Figure 14. In this mode, the input
ports are write enable (WE), write-port enable (WPE),
read/write address (A[3:0]), and write data (WD[3:0]).
To synchronously write the RAM, WE (input into a4)
and WPE (input into either C0 or CIN) are latched and
ANDed together . The result of this AND function is sent
to a pulse generator in the LUT, which writes the RAM
synchronous to the RAM clock. This RAM clock is the
same one sent to the PFU latches/FFs; how e v er, if nec-
essary, it can be programmably inverted.
5-4642(F).r1
Figure 14. SSPM Mode—16 x 4 Synchronous
Single-Port Memory
The write address (WA[3:0]) and write data (WD[3:0])
are also latched by the RAM clock in order to simplify
the timing. Reading data from the RAM is done asyn-
chronously; thus, the read address (RA[3:0]) is not
latched. The result from the read operation is placed on
the LUT outputs (F[3:0]). The F[3:0] data outputs can
be routed out of the PFU or sent to the latch/FF D[3:0]
inputs.
There are two ways to use the latches/FFs in conjunc-
tion with the SSPM. If the phase of the latch/FF clock
and the RAM clock are the same, only a read address
or write address can be supplied to the RAM that
meets the synchronous timing requirements of both
the RAM clock and latch/FF clock. Therefore, either a
write to the RAM or a read from the RAM can be done
in each clock cycle, but not both. If the RAM clock is
inverted from the latch/FF clock, then both a write to
the RAM and a read from the RAM can occur in each
clock cycle. This is done by adding an external write
address/read address multiplexer as shown in
Figure 15.
The write address is supplied on the phase of the clock
that allows for setup to the RAM clock, and the read
address is supplied on the phase of the clock that
allows the read data to be set up to the latch/FF clock.
If a higher-speed RAM is required that allows both a
read and write in each clock cycle, the synchronous
dual-port memory mode (SDPM) can be used, since it
does not require the use of an external multiplexer.
5-4644(F).r1
Figure 15. SSPM with Read/Write per Cloc k Cycle
WE
WPE
A4 DQ
DQ
CIN, C0
A[3:0]
WD[3:0]
WR
WA[3:0]
RA[3:0]
WD[3:2]
HLUTA
F3
F2
DQ
DQ
WR
WA[3:0]
RA[3:0]
WD[1:0]
HLUTB
F1
F0
WRITE PULSE
GENERATOR
A[3:0], B[3:0]
WD[3:0]
WE
A
WD
RAM CLK
WRITE ADDRESS
READ ADDRESS 0
1
WPE
SSPM
CLOCK
DQ
PFU
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
14 Lucent Technologies Inc.
Programmable Logic Cells (continued)
Note: The lower address bits are not shown.
Figure 16. Synchronous RAM with Write-Port Enable (WPE)
UPPER
ADDRESS
BITS
ADDRESS
DECODE
LUT1
BANK_EN1
UPPER
ADDRESS
BITS
ADDRESS
DECODE
LUT2
BANK_EN2
WR
DI
WPE
DO
16 x 4 RAM +
4 B UFFERS/PFU
BIDI
DOUT
4
WR
DI
WPE
DO
16 x 4 RAM +
4 B UFFERS/PFU
DIN
WR
CLK
4
BIDI
4
4
5-4640(F)
To increase memory word depth above 16 (e.g., 32 x
4), two or more PLCs can be used. The address and
write data inputs for the two or more PLCs are tied
together (bit by bit), and the data outputs are routed
through the four 3-statable BIDIs available in each
PFU. The BIDI outputs are then tied together (bit by
bit), as seen in Figure 16.
The control signals of the 3-statable BIDIs, called RAM
bank-enable (BANK_EN1 and BANK_EN2), are cre-
ated from a decode of upper address bits. The RAM
bank-enable is then used to enable 4 bits of data from
a PLC onto the read data (DOUT) bus .
The Series 2 series now has a new AND function avail-
able for each PFU in RAM mode. The inputs to this
function are the write-enable (WE) signal and the write-
port enable (WPE) signal. The write-enable signal is
input on A4, while the write-port enable is input on C0
or CIN. Generally, the WPE input is driven by the same
RAM bank-enable signal that controls the BIDIs in each
PFU.
The selection as to which RAM bank to write data into
does not require the use of LUTs from other PFUs, as
in pr e vi ous
ORCA
architectures. This reduces the num-
ber of PFUs required for RAMs larger than 16 words in
depth.
A special use of this method can be to increase word
depth to 32 words. Since both the WPE input into the
RAM and the 3-state input into the BIDI can be
inverted, a decode of the one upper address bit is not
required. Instead, the bank-enable signal for both
banks is tied to the upper address bit, with the WPE
and 3-state inputs active-high for one bank and active-
low for the other.
To increase the memory’s word size (e.g., 16 x 8), two
or more PLCs are used again. The address, write-
enable, and write-port enable of the PLCs are tied
together (bit by bit), and the data is different for each
PLC. Increasing both the address locations and word
size is accomplished by using a combination of these
two techniques.
Lucent Technologies Inc. 15
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Programmable Logic Cells (continued)
5-4641(F).r1
Figure 17. SDPM Mode—16 x 2 Synchronous
Dual-Port Memory
The Series 2 devices have added a second synchro-
nous memory mode known as the synchronous dual-
port memory (SDPM) mode. This mode writes data
into the memory synchronously in the same manner
described previously for SSPM mode. The SDPM
mode differs in that two separate 16 x 2 memories are
created in each PFU that have the same WE, WPE,
write data (WD[1:0]), and write address (WA[3:0])
inputs, as shown in Figure 17.
The outputs of HLUTA (F[3:2]) operate the same way
they do in SSPM mode—the read address comes
directly from the A[3:0] inputs used to create the
latched write address. The outputs of HLUTB (F[1:0])
operate in a dual-port mode where the write address
comes from the latched version of A[3:0], and the read
address comes directly from RA[3:0], which is input on
B[3:0].
Since external multiplexing of the write address and
read address is not required, extremely fast RAMs can
be created. New system applications that require an
interface between two different asynchronous clocks
can also be implemented using the SDPM mode. An
example of this is accomplished by creating FIFOs
where one clock controls the synchronous write of data
into the FIFO, and the other clock controls the read
address to allow reading of data at any time from the
FIFO.
Latches/Flip-Flops
The four latches/FFs in the PFU can be used in a vari-
ety of configurations. In some cases, the configuration
options apply to all four latches/FFs in the PFU. For
other options, each latch/FF is independently program-
mable .
Table 4 summarizes these latch/FF options. The
latches/FFs can be configured as either positive or
negative level-sensitive latches, or positive or negative
edge-triggered flip-flops. All latches/FFs in a given PFU
share the same clock, and the clock to these latches/
FFs can be inverted. The input into each latch/FF is
from either the corresponding QLUT output (F[3:0]) or
the direct data input (WD[3:0]). For latches/FFs located
in the two outer rings of PLCs, additional inputs are
possible. These additional inputs are fast paths from
I/O pads located in PICs in the same row or column as
the PLCs. If the latch/FF is not located in the two outer
rings of the PLCs, the latch/FF input can also be tied to
logic 0, which is the default. The four latch/FF outputs,
Q[3:0], can be placed on the five PFU outputs, O[4:0].
Table 4. Configuration RAM Controlled Latch/
Flip-Flop Operation
The four latches/FFs in a PFU share the clock (CK),
clock enable (CE), and local set/reset (LSR) inputs.
When CE is disab led, each latch/FF retains its previous
value when clocked. Both the clock enable and LSR
inputs can be inverted to be active-low.
WE
WPE
A4 DQ
DQ
CIN, C0
WA[3:0]
WD[1:0]
WR
WA[3:0]
RA[3:0]
WD[1:0]
HLUTA
F3
F2
DQ
DQ
WR
WA[3:0]
RA[3:0]
WD[1:0]
HLUTB
F1
F0
WRITE PULSE
GENERATOR
A[3:0]
WD[1:0]
RA[3:0] B[3:0]
SSPM OUTPUT SDPM OUTPUT
Function Options
Functionality Common to All Latch/FFs in PFU
LSR Op eratio n Asynch ronous or synchronous
Clock Polarity Noninverted or inverted
Fron t- End Select Dire c t (WD [ 3: 0] ) or from LUT
(F[3:0])
LSR Priority Either LS R or C E has prio rity
Functionality Set Individua ll y in Each Latch/FF in PFU
Latch/ FF M ode Latch or f lip-f lop
Set/Reset Mode Set or Reset
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
16 Lucent Technologies Inc.
Programmable Logic Cells (continued)
The set/reset operation of the latch/FF is controlled by
two parameters: reset mode and set/reset value. When
the global set/reset (GSRN) or local set/reset (LSR) are
inactive, the storage element operates normally as a
latch or FF. The reset mode is used to select a synchro-
nous or asynchronous LSR operation. If synchronous,
LSR is enabled only if clock enable (CE) is active. For
the Series 2 series, a new option called the LSR pri or-
ity allows the synchronous LSR to hav e priority ov er the
CE input, thereby setting or resetting the FF indepen-
dent of the state of CE. The clock enable is supported
on FFs, not latches. The clock enable function is imple-
mented by using a two-input multiplexer on the FF
input, with one input being the previous state of the FF
and the other input being the new data applied to the
FF. The select of this two-input multiplexer is clock
enable (CE), which selects either the new data or the
previous state. When CE is inactive, the FF output
does not change when the clock edge arrives.
The GSRN signal is only asynchronous, and it sets/
resets all latches/FFs in the FPGA based upon the set/
reset configuration bit for each latch/FF. The set/reset
value determines whether GSRN and LSR are set or
reset inputs. The set/reset value is independent for
each latch/FF.
If the local set/reset is not needed, the latch/FF can be
configured to have a data front-end select. Two data
inputs are possible in the front-end select mode, with
the LSR signal used to select which data input is used.
The data input into each latch/FF is from the output of
its associated QLUT F[3:0] or direct from WD[3:0],
bypassing the LUT. In the front-end data select mode,
both signals are available to the latches/FFs.
F or PLCs that are in the two outside rows or columns of
the array, the latch/FFs can have two inputs in addition
to the F and WD inputs mentioned above. One input is
from an I/O pad located at the PIC closest to either the
left or right of the given PLC (if the PLC is in the left two
columns or right two columns of the array). The other
input is from an I/O pad located at the closest PIC
either above or below the given PLC (if the PLC is in
the top or the bottom two rows). It should be noted that
both inputs are available for a 2 x 2 array of PLCs in
each corner of the arra y. For the entire arra y of PLCs, if
either or both of these inputs is unavailable, the latch/
FF data input can be tied to a logic 0 instead (the
default).
To speed up the interface between signals external to
the FPGA and the latches/FFs, there are direct paths
from latch/FF outputs to the I/O pads. This is done for
each PLC that is adjacent to a PIC .
The latches/FFs can be configured in three modes:
1. Local synchronous set/reset: the input into the PFU’ s
LSR port is used to synchronously set or reset each
latch/FF.
2. Local asynchronous set/reset: the input into LSR
asynchronously sets or resets each latch/FF.
3. Latch/FF with front-end select: the data select signal
(actually LSR) selects the input into the latches/FFs
between the LUT output and direct data in.
For all three modes, each latch/FF can be indepen-
dently programmed as either set or reset. Each latch/
FF in the PFU is independently configured to operate
as either a latch or flip-flop. Figure 18 provides the logic
functionality of the front-end select, global set/reset,
and local set/reset operations.
Note: CD = configur ation data.
5-2839(F).a
Figure 18. Latch/FF Set/Reset Configurations
CE
D
S_SET
S_RESET
CLK
SET RESET
Q
LSR
GSRN
CD
CE
D
CLK
SET RESET
LSR
CD
CE
CE
D
CLK
SET RESET
CD
CE
CE
WD
LSR
GSRN
PDINLR
LOGIC 0
WD F
LOGIC 0
WD
GSRN
Q Q
PDINTB
FPDINLR
PDINTB F
LOGIC 0
WD
PDINLR
PDINTB
Lucent Technologies Inc. 17
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Programmable Logic Cells (continued)
PLC Routing Resources
Generally, the
ORCA
Foundr y
Development System is
used to automatically route interconnections. Interac-
tive routing with the
ORCA
Foundry design editor
(EPIC) is also available for design optimization. To use
EPIC for interactive layout, an understanding of the
routing resources is needed and is provided in this sec-
tion.
The routing resources consist of s witching circuitry and
metal interconnect segments. Generally, the metal lines
which carry the signals are designated as routing
nodes (lines). The switching circuitry connects the rout-
ing nodes, providing one or more of three basic func-
tions: signal switching, amplification, and isolation. A
net running from a PFU or PIC output (source) to a
PLC or PIC input (destination) consists of one or more
lines, connected by switching circuitry designated as
configurable interconnect points (CIPs).
The f ollowing sections discuss PLC, PIC, and interquad
routing resources. This secti on dis cus se s the PLC
s witching circuitry, intra-PLC routing, inter-PLC routing,
and clock distribution.
Configurable Interconnect Points
The process of connecting lines uses three basic types
of switching circuits: two types of configurable intercon-
nect points (CIPs) and bidirectional buff ers (BIDIs). The
basic element in CIPs is one or more pass transistors,
each controlled by a configuration RAM bit. The two
types of CIPs are the mutually exclusive (or multi-
plexed) CIP and the independent CIP.
A mutually exclusive set of CIPs contains two or more
CIPs, only one of which can be on at a time. An inde-
pendent CIP has no such restrictions and can be on
independent of the state of other CIPs. Figure 19
shows an example of both types of CIPs.
f.13(F)
Figure 19. Configurab le Interconnect Point
3-Statable Bidirectional Buffers
Bidirectional buffers provide isolation as well as amplifi-
cation for signals routed a long distance. Bidirectional
buffers are also used to drive signals directly onto
either vertical or horizontal XL and XH lines (to be
described later in the inter-PLC routing section). BIDIs
are also used to indirectly route signals through the
switching lines. Any number from zero to eight BIDIs
can be used in a given PLC.
The BIDIs in a PLC are divided into two nibble-wide
sets of four (BIDI and BIDIH). Each of these sets has a
separate BIDI controller that can hav e an application
net connected to its TRI input, which is used to 3-state
enable the BIDIs. Although only one application net can
be connected to both BIDI controllers, the sense of this
signal (active-high, active-low, or ignored) can be con-
figured independently. Therefore, one set can be used
for driving signals, the other set can be used to create
3-state b uses, both sets can be used for 3-state buses,
and so forth.
2
INDEPENDENT CIP
CD
A
B
AB
=
MULTIPLEXED CIP
A
B
C
A
B
C
O
O
CD
18 Lucent Technologies Inc.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
Programmable Logic Cells (continued)
5-4479p2(F)
Figure 20. 3-Statable Bidirectional Buffers
Intra-PLC Routing
The function of the intra-PLC routing resources is to
connect the PFU’s input and output ports to the routing
resources used for entry to and exit from the PLC.
These are nets for providing PFU feedback, turning
corners, or switching from one type of routing resource
to another.
PFU Input and Output Ports. There are 19 input ports
to each PFU. The PFU input ports are labeled A[4:0],
B[4:0], WD[3:0], C0, CK, LSR, CIN, and CE. The six
output ports are O[4:0] and COUT. These ports corre-
spond to those described in the PFU section.
Swit ch ing Lin es. There are f our sets of s witching lines
in each PLC, one in each corner. Each set consists of
five switching elements, labeled SUL[4:0], SUR[4:0],
SLL[4:0], and SLR[4:0], for the upper-left, upper-right,
lower-left, and lower-right sections of the PFUs,
respectively. The switching lines connect to the PFU
inputs and outputs as well as the BIDI and BIDIH lines,
to be described later. They also connect to both the
horizontal and vertical X1 and X4 lines (inter-PLC rout-
ing resources, described below) in their specific corner .
One of the four sets of switching lines can be con-
nected to a set of switching lines in each of the four
adjacent PLCs or PICs. This allows direct routing of up
to five signals without using inter-PLC routing.
BIDI/BIDIH Lines. There are two sets of bidirectional
lines in the PLC, each set consisting of four bidirec-
tional buff ers. They are designated BIDI and BIDIH and
have similar functionality. The BIDI lines are used in
conjunction with the XL lines, and the BIDIH lines are
used in conjunction with the XH lines. Each side of the
f our BIDIs in the PLC is connected to a BIDI line on the
left (BL[3:0]) and on the right (BR[3:0]). These lines can
be connected to the XL lines through CIPs, with BL[3:0]
connected to the vertical XL lines and BR[3:0] con-
nected to the horizontal XL lines. Both BL[3:0] and
BR[3:0] hav e CIPs which connect to the switching lines.
Similarly, each side of the f our BIDIHs is connected to a
BIDIH line: BLH[3:0] on the left and BRH[3:0] on the
right. These lines can also be connected to the XH
lines through CIPs, with BLH[3:0] connected to the ver-
tical XH lines and BRH[3:0] connected to the horizontal
XH lines . Both BLH[3:0] and BRH[3:0] hav e CIPs which
connect to the switching lines.
CIPs are also provided to connect the BIDIH and BIDIL
lines together on each side of the BIDIs. For example,
BLH3 can connect to BL3, while BRH3 can connect to
BR3.
RIGHT-LEFT BIDI
LEFT-RIGHT BIDI
UNUSED BIDI
LEFT-RIGHT BIDI
BIDI
CONTROLLER
TRI
RIGHT-LEFT BIDIH
LEFT-RIGHT BIDIH
UNUSED BIDIH
LEFT-RIGHT BIDIH
BIDIH
CONTROLLER
Lucent Technologies Inc. 19
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Programmable Logic Cells (continued)
Inter-PLC Routing Resources
The inter-PLC routing is used to route signals between
PLCs. The lines occur in groups of f our , and differ in the
numbers of PLCs spanned. The X1 lines span one
PLC, the X4 lines span four PLCs, the XH lines span
one-half the width (height) of the PLC arra y, and the XL
lines span the width (height) of the PLC array. All types
of lines run in both horizontal and vertical directions.
Tab le 5 shows the groups of inter-PLC lines in each
PLC. In the table, there are two rows/columns each for
X1 and X4 lines. In the design editor, the horizontal X1
and X4 lines are located above and below the PFU.
Similarly, the vertical segments are located on each
side. The XL and XH lines only run below and to the left
of the PFU . The inde xes specify individual lines within a
group. For example, the VX4[2] line runs vertically to
the left of the PFU, spans four PLCs, and is the third
line in the 4-bit wide bus .
Table 5. Inter-PLC Routing Resources
Figure 21 shows the inter-PLC routing within one PLC .
Figure 22 provides a global view of inter-PLC routing
resources across multiple PLCs.
5-4528(F)
Figure 21. Single PLC View of Inter-PLC Lines
X1 Lines. There are a total of 16 X1 lines per PLC:
eight vertical and eight horizontal. Each of these is sub-
divided into nibble-wide buses: HX1[3:0], HX1[7:4],
VX1[3:0], and VX1[7:4]. An X1 line is one PLC long.
If a net is longer than one PLC, an X1 line can be
lengthened to n times its length by turning on n – 1
CIPs. A signal is routed onto an X1 line via the switch-
ing lines.
X4 Lines. There are four sets of four X4 lines, for a
total of 16 X4 lines per PLC. They are HX4[3:0],
HX4[7:4], VX4[3:0], and VX4[7:4]. Each set of X4 lines
is twisted each time it passes through a PLC, and one
of the four is broken with a CIP. This allows a signal to
be routed for a length of four cells in any direction on a
single line without additional CIPs. The X4 lines can be
used to route any nets that require minimum delay. A
longer net is routed by connecting two X4 lines
together by a CIP. The X4 lines are accessed via the
switchi ng li nes.
Horizontal
Lines Vertical
Lines Distance
Spanned
HX1[3:0] VX1[3:0] One PLC
HX1[7:4] VX1[7:4] One PLC
HX4[3:0] VX4[3:0] Four PLCs
HX4[7:4] VX4[7:4] Four PLCs
HXL[3:0] VXL[3:0] PLC Array
HXH[3:0] VXH[3:0] 1/2 PLC Array
CKL, CKR CKT, CKB PLC Array
PROGRAMMABLE
FUNCTION UNIT
DIRECT[4:0]
HX4[7:4]
HX1[7:4]
DIRECT[4:0]
HXH[3:0]
HX1[3:0]
DIRECT[4:0]
DIRECT[4:0]
HX4[3:0]
VX4[7:4]
VX1[7:4]
VXL[3:0]
VX1[3:0]
VX4[3:0]
VXH[3:0]
CKB , CKT
HXL[3:0]
CKL, CKR
20 Lucent Technologies Inc.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
Programmable Logic Cells (continued)
XL Lines. The long XL lines run vertically and horizon-
tally the height and width of the array, respectively.
There are a total of eight XL lines per PLC: four hori-
zontal (HXL[3:0]) and four vertical (VXL[3:0]). Each
PLC column has four XL lines, and each PLC row has
four XL lines. Each of the XL lines connects to the two
PICs at either end. The Series 2, which consists of a
18 x 18 array of PLCs, contains 72 VXL and 72 HXL
lines. They are intended primarily for global signals
which must travel long distances and require minimum
delay and/or skew, such as clocks.
There are three methods f or routing signals onto the XL
lines. In each PLC, there are two long-line drivers: one
for a horizontal XL line, and one for a vertical XL line.
Using the long-line drivers produces the least delay.
The XL lines can also be driven directly by PFU outputs
using the BIDI lines. In the third method, the XL lines
are accessed by the bidirectional buffers, again using
the BIDI lines.
XH Line s. Four b y half (XH) lines run horizontally and
four XH lines run vertically in each row and column in
the array. These lines travel a distance of one-half the
PLC array before being broken in the middle of the
array, where they connect to the interquad block (dis-
cussed later). They also connect at the periphery of the
FPGA to the PICs, like the XL lines. The XH lines do
not twist like XL lines, allowing nibble-wide buses to be
routed easily.
Two of the three methods of routing signals onto the
XL lines can also be used for the XH lines. A special
XH line driver is not supplied for the XH lines.
Clock Lines. For a very fast and low-skew clock (or
other global signal tree), clock lines run the entire
height and width of the PLC array. There are two hori-
zontal clock lines per PLC row (CKL, CKR) and two
vertical clock lines per PLC column (CKT, CKB). The
source for these clock lines can be any of the four I/O
buffers in the PIC. The horizontal clock lines in a row
(CKL, CKR) are driven b y the left and right PICs,
respectively. The vertical clock lines in a column (CKT,
CKB) are driven by the top and bottom PICs, respec-
tively.
The clock lines are designed to be a clock spine. In
each PLC, there is a fast connection available from the
clock line to the long-line driver (described earlier).
With this connection, one of the clock lines in each PLC
can be used to drive one of the four XL lines perpendic-
ular to it, which, in turn, creates a clock tree.
This feature is discussed in detail in the Clock Distribu-
tion Network section.
Minimizing Routing Delay
The CIP is an activ e element used to connect two lines.
As an active element, it adds significantly to the resis-
tance and capacitance of a net, thus increasing the
net’s delay. The advantage of the X1 line ov er a X4 line
is rou tin g fl e xib ilit y. A ne t f rom PLC db to PL C cb is eas -
ily routed b y using X1 lines. As more CIPs are added to
a net, the delay increases. To increase speed, routes
that are greater than two PLCs away are routed on the
X4 lines because a CIP is located only in every fourth
PLC. A net that spans eight PLCs requires sev en X1
lines and six CIPs. Using X4 lines, the same net uses
two lines and one CIP.
All routing resources in the PLC can carry 4-bit buses.
In order for data to be used at a destination PLC that is
in data path mode, the data must arrive unscrambled.
For example, in data path operation, the least signifi-
cant bit 0 must arrive at either A[0] or B[0]. If the bus is
to be routed by using either X4 or XL lines (both of
which twist as they propagate), the bus must be placed
on the appropriate lines at the source PLC so that the
data arrives at the destination unscrambled. The
s witching lines pro vide the most efficient means of con-
necting adjacent PLCs. Signals routed with these lines
have minimum propagation delay.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 21
Programmable Logic Cells (continued)
5-2841(F)2C.r9
Figure 22. Multiple PLC View of Inter -PLC Routing
PFU
PFU
PFU PFU
PFUPFU
PFUPFU
PFU
SHO W S PLC s
CKR
CKL CKR
CKL
HX4[4]
HX4[5]
HX4[6]
HX4[7]
HX1[7:4]
HX4[5]
HX4[6]
HX4[7]
HX4[4]
HXL[0]
HXL[1]
HXL[2]
HXL[3]
HX1[3:0]
HX4[0]
HX4[1]
HX4[2]
HX4[3]
HXL[3]
HXL[0]
HXL[1]
HXL[2]
HX4[1]
HX4[2]
HX4[3]
HX4[0]
HX4[4]
HX4[5]
HX4[6]
HX4[7]
HX1[7:4]
HX4[5]
HX4[6]
HX4[7]
HX4[4]
HX1[7:4]
HX4[4]
HX4[5]
HX4[6]
HX4[7]
HX4[5]
HX4[6]
HX4[7]
HX4[4]
HXL[0]
HXL[1]
HXL[2]
HXL[3]
HX4[0]
HX4[1]
HX4[2]
HX4[3]
HXL[3]
HXL[0]
HXL[1]
HXL[2]
HX4[1]
HX4[2]
HX4[3]
HX4[0]
CKR
CKL
HXH[3:0]
HX1[7:4]
HX1[3:0]
CKR
CKL
HXH[3:0]
HX1[7:4]
HX1[3:0]
CKR
CKL
HXH[3:0]
HX1[7:4]
HX1[3:0]
CKR
CKL
HXH[3:0]
VX1[3:0]
CKT
CKB
VX4[0]
VX4[1]
VX4[2]
VX4[3]
VX4[4]
VX4[5]
VX4[6]
VX4[7]
VXH[3:0]
VX1[7:4]
VXL[0]
VXL[1]
VXL[2]
VXL[3]
VX4[1]
VX4[2]
VX4[3]
VX4[0]
VX4[5]
VX4[6]
VX4[7]
VX4[4]
VXL[1]
VXL[2]
VXL[3]
VXL[0]
VX4[0]
VX4[1]
VX4[2]
VX4[3]
VX1[3:0]
CKT
CKB
VX4[1]
VX4[2]
VX4[3]
VX4[0]
VX4[0]
VX4[1]
VX4[2]
VX4[3]
VX4[4]
VX4[5]
VX4[6]
VX4[7]
VXL[0]
VXL[1]
VXL[2]
VXL[3]
VX4[1]
VX4[2]
VX4[3]
VX4[0]
VX4[5]
VX4[6]
VX4[7]
VX4[4]
VXL[3]
VXL[0]
VXL[1]
VXL[2]
VX1[3:0]
CKT
CKB
VX1[3:0]
CKT
CKB
VXH[3:0]
VX1[7:4]
VX1[3:0]
CKT
CKB
VXH[3:0]
VX1[7:4]
VX1[3:0]
CKT
CKB
VXH[3:0]
VX1[7:4]
22 Lucent Technologies Inc.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
Programmable Logic Cells (continued)
PLC Architectural Description
Figure 23 is an architectural drawing of the PLC which
reflects the PFU, the lines, and the CIPs. A discussion
of each of the letters in the drawing follows.
A. These are switching lines which give the router flexi-
bility. In general switching theory, the more lev els of
indirection there are in the routing, the more routable
the network is . The switching lines can also connect
to adjacent PLC s.
The switching lines provide direct connections to
PLCs directly to the top, bottom, left, and right, with-
out using other routing resources. The ability to dis-
able this connection between PLCs is provided so
that each side of these connections can be used
exclusively as switching lines in their respective
PLC.
B. These CIPs connect the X1 routing. These are
located in the middle of the PLC to allow the block to
connect to either the left end of the horizontal X1 line
from the right or the right end of the horizontal X1
line from the left, or both. By symmetry, the same
principle is used in the vertical direction. The X1
lines are not twisted, making them suitable for data
paths.
C. This set of CIPs is used to connect the X1 and X4
nets to the switching lines or to other X1 and X4
nets. The CIPs on the major diagonal allow data to
be transmitted from X1 nets to the switching lines
without being scrambled. The CIPs on the major
diagonal also allow unscrambled data to be passed
between the X1 and X4 nets.
In addition to the major diagonal CIPs for the X1
lines, other CIPs provide an alternative entry path
into the PLC in case the first one is already used.
The other CIPs are arrayed in two patterns, as
shown. Both of these patterns start with the main
diagonal, but the extra CIPs are arrayed on either a
parallel diagonal shifted by one or shifted by two
(modulo the size of the vertical bus (5)). This allows
any four application nets incident to the PLC corner
to be transferred to the five switching lines in that
corner. Many patterns of five nets can also be trans-
ferred.
D. The X4 lines are twisted at each PLC. One of the
four X4 lines is broken with a CIP, which allows a sig-
nal to be rou te d a dist anc e of four PLCs in an y di rec -
tion on a single line without an intermediate CIP. The
X4 lines are less populated with CIPs than the X1
lines to increase their speed. A CIP can be enabled
to extend an X4 line four more PLCs, and so on.
For example, if an application signal is routed onto
HX4[4] in a PLC, it appears on HX4[5] in the PLC to
the right. This signal step-up continues until it
reaches HX4[7], two PLCs later. At this point, the
user can break the connection or continue the signal
for another four PLCs.
E. These symbols are bidirectional buffers (BIDIs).
There are four BIDIs per PLC, and they provide sig-
nal amp lif ic ation as nee ded to d ecre as e sign al
delay. The BIDIs are also used to transmit signals on
XL lines.
F. These are the BIDI and BIDIH controllers. The 3-
state control signal can be disabled. They can be
configured as active-high or active-low indepen-
dently of each other.
G.This set of CIPs allows a BIDI to get or put a signal
from one set of switching lines on each side. The
BIDIs can be accessed b y the s witchi ng lines . These
CIPs allow a nibble of data to be routed though the
BIDIs and continue to a subsequent block. They also
provide an alternative routing resource to improve
routability.
H.These CIPs are used to take data from/to the BIDIs
to/from the XL lines. These CIPs have been opti-
mized to allow the BIDI buff ers to drive the large load
usually seen when using XL lines.
I. Each latch/FF can accept data: from an LUT output;
from a direct data input signal from general routing;
or, as in the case of PLCs located in the two rows
(columns) adjacent to PICs, directly from the pad. In
addition, the LUT outputs can bypass the latches/
FFs completely and output data on the general rout-
ing resources. The four inputs shown are used as
the direct input to the latches/FFs from general rout-
ing resources. If the LUT is in memory mode, the
four inputs WD[3:0] are the data input to the mem-
ory.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 23
Programmable Logic Cells (continued)
5-4479(F).r2
Figure 23. PLC Architecture
PFU:R1C2
HX4[7]
HX4[6]
HX4[5]
HX4[4]
HX1[7]
HX1[6]
HX1[5]
HX1[4]
INL[4]
INL[3]
INL[2]
INL[1]
INL[0]
VX4[7]
VX4[6]
VX4[5]
VX4[4]
VX1[7]
VX1[6]
VX1[5]
VX1[4]
VXL[3]
VXL[2]
VXL[1]
VXL[0]
CARRY_T
CKL
CKR
CARRY_L
VXH[3]
VXH[2]
VXH[1]
VXH[0]
VX4[4]
VX4[7]
VX4[6]
VX4[5]
VX1[7]
VX1[6]
VX1[5]
VX1[4]
VXL[0]
VXL[3]
VXL[2]
VXL[1]
HXL[3]
HXL[2]
HXL[1]
HXL[0]
HX4[3]
HX4[2]
HX4[1]
HX4[0]
HX1[3]
HX1[2]
HX1[1]
HX1[0]
CARRY_B
HXH[3]
HXH[2]
HXH[1]
HXH[0]
VXH[3]
VXH[2]
VXH[1]
VXH[0]
HXL[0]
HXL[3]
HXL[2]
HXL[1]
HX4[2]
HX4[1]
HX4[0]
HX4[3]
HX1[3]
HX1[2]
HX1[1]
HX1[0]
VX1[3]
VX1[2]
VX1[1]
VX1[0]
VX4[0]
VX4[3]
VX4[2]
VX4[1]
INB[4]
INB[3]
INB[2]
INB[0]
INB[1]
HXH[3]
HXH[2]
HXH[1]
HXH[0]
GSRN
CKB
CKT
INT[4]
INT[3]
INT[2]
INT[1]
INT[0]
HX4[6]
HX4[5]
HX4[4]
HX4[7]
HX1[7]
HX1[6]
HX1[5]
HX1[4]
INR[4]
INR[3]
INR[2]
INR[1]
INR[0]
CKL
CKR
CARRY_R
GSRN
VX1[3]
VX1[2]
VX1[1]
VX1[0]
VX4[3]
VX4[2]
VX4[1]
VX4[0]
CKB
CKT
HCK
VCK
LSR
CE
COUT
CIN
J
N
CK GSRN
A[4]
A[3]
A[2]
A[1]
A[0]
B[4]
B[3]
B[2]
B[1]
B[0]
C0
WD[3]
WD[2]
WD[1]
WD[0]
O[2]
O[0]
O[4]
I
O[3]
O[1]
SEE FIGURE 14
C
CB
L
D
B
A
D
C
B
A
AA A A
Q
H
L
C
C
A
K
N
F
M
DB
C
M
D
A
T T
S
U
U
TT
L
S
R
PQ
R
O
G
E
O
U
W
U
V
C
C
G
H
L
24 Lucent Technologies Inc.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
Programmable Logic Cells (continued)
J. Any five of the eight output signals can be routed out
of the PLC. The eight signals are the four LUT out-
puts (F0, F1, F2, and F3) and the four latch/FF out-
puts (Q0, Q1, Q2, and Q3). This allows the user to
access all four latch/FF outputs, read the present
state and ne xt state of a latch/FF, build a 4-bit shift
register, etc. Each of the outputs can drive any num-
ber of the five PFU outputs. The speed of a signal
can be increased by dividing its load among multiple
PFU output drivers.
K. These lines deliver the auxiliary signals’ clock
enable and set/reset to the latches/FFs. All four of
the latches/FFs share these signals.
L. This is the clock input to the latches/FFs. Any of the
horizontal and vertical XH or XL lines can drive the
clock of the PLC latches/FFs. Long-line drivers are
provided so that a PLC can drive one XL line in the
hor i zontal dir ec ti on and one XL li ne in the ver t ic al
direction. The XL lines in each direction exhibit the
same properties as X4 lines, except there are no
CIPs. The clock lines (CKL, CKR, CKT, and CKB)
and multiplexers/drivers are used to connect to the
XL lines for low-skew, low-delay global signals.
The long lines run the length or width of the PLC
array. They rotate to allow four PLCs in one row or
column to generate four independent global signals.
Thes e lines d o not ha v e to be used f o r cloc k rou ting.
Any highly used application net can use this
resource, especially one requiring low skew.
M.These lines are used to route the f ast carry signal to/
fro m the neighboring four PLCs. The carry-ou t
(COUT) of the PFU can also be routed out of the
PFU onto the fifth output (O4). The carry-in (CIN)
signal can also be supplied by the B4 input to the
PFU.
N. These are the 11 logic inputs to the LUT. The A[4:0]
inputs are provided into HLUTA, and the B[4:0]
inputs are provided into HLUTB. The C0 input
bypasses the main LUT and is used in the pfumux,
pfuxor, and pfunand functions (F5M, F5X modes).
Since this input b ypasses the LUT, it can be used as
a fast path around the LUT, allowing the implemen-
tation of fast, wide combinatorial functions. The C0
input can be disabled or inverted.
O. The XH lines run one-half the length (width) of the
array before being broken by a CIP.
P
. The BIDIHs are used to access the XH lines.
Q.The BIDIH lines are used to connect the BIDIHs to
the XSW lines, the XH lines, or the BIDI lines.
R. These CIPs connect the BIDI lines and the BIDIH
lines.
S. These are clock lines (CKT, CKB, CKL, and CKR)
with the multiplex ers and drivers to connect to the
XL lines.
T. These CIPs connect X1 lines which cross in each
corner to allow turns on the X1 lines without using
the XSW lines.
U. These CIPs connect X4 lines and xsw lines, allowing
nets that run a distance that is not divisible b y f our to
be routed more efficiently.
V. This routing structure allows an y PFU output, includ-
ing LUT and latch/FF outputs, to be placed on O4
and be routed onto the fast carry routing.
W.This routing structure allows the f ast carry routing to
be routed onto the C0 PFU input.
Lucent Technologies Inc. 25
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Programmable Input/Output Cells
The programmable input/output cells (PICs) are
located along the perimeter of the device. Each PIC
interfaces to four bond pads and contains the neces-
sary routing resources to provide an interface between
I/O pads and the PLCs. Each PIC is composed of input
buffers, output buffers, and routing resources as
described below. Table 6 provides an overview of the
programmable functions in an I/O cell. A is a simplified
diagram of the functionality of the OR2CxxA
series I/O
cells, while B is a simplified functional diagram of the
OR2TxxA and OR2TxxB series I/O cells.
Table 6. Input/Output Cell Options
Inputs
Each I/O can be configured to be either an input, an
output, or bidirectional I/O. Inputs for the OR2CxxA can
be configured as either TTL or CMOS compatible. The
I/O for the OR2TxxA and OR2TxxB series devices are
5 V tolerant, and will be described in a later section of
this data sheet. Pull-up or pull-down resistors are avail-
able on inputs to minimize power consumption.
To allow zero hold time to PLC latches/FFs, the input
signal can be delay ed. When enabled, this delay aff ects
the input signal driven to general routing, but does not
affect the clock input or the input lines that drive the
TRIDI buffers (used to drive onto XL, XH, BIDI, and
BIDIH lines).
A fast path from the input buffer to the clock lines is
also provided. Any one of the four I/O pads on any PIC
can be used to drive the clock line generated in that
PIC. This path cannot be delayed.
To reduce the time required to input a signal into the
FPGA, a dedicated path (PDIN) from the I/O pads to
the PFU flip-flops is provided. Like general input sig-
nals, this sign al can be configured as normal or
dela y ed. The delay ed direct input can be selected inde-
pendently from the delayed general input.
Inputs should have transition times of less than 500 ns
and should not be left floating. If an input can float, a
pul l-up or pull -do wn shou l d be ena b l ed. F loa tin g inp uts
increase power consumption, produce oscillations, and
increase system noise. The OR2CxxA inputs have a
typical hysteresis of approximately 280 mV (200 mV f or
the OR2TxxA and OR2TxxB) to reduce sensitivity to
input noise. The PIC contains input circuitry which pro-
vides protection against latch-up and electrostatic dis-
charge.
Input Option
Input Levels TTL/CMOS (OR2CxxA only)
5 V PCI compliant (OR2CxxA only)
3.3 V PCI compliant (OR2TxxA only)
3.3 V and 5 V PCI compliant
(OR2TxxB onl y)
Input Speed Fast/De layed
Float Value Pull-up/Pull-down/None
Direct-in to FF Fast/Delayed
Output Option
Output Drive 12 mA/6 mA or 6 mA/3 mA
Output Speed Fast/Slewlim/Sinklim
Output Source FF Direct-out/General Routing
Output Sense Activ e-high/-low
3-State Sense Active-high/-low (3-state)
26 Lucent Technologies Inc.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
Programmable Input/Output Cells
(continued)
A. Simplified Diagram of OR2CxxA Programmable
I/O Cell (PIC)
B. Simplified Diagram of OR2TxxA/OR2TxxB
Programmable I/O Cell (PIC)
Figure 24. Simplified Diagrams
Outputs
The PIC’s output drivers have programmable drive
capability and slew rates. Three propagation delays
(fast, slewlim, sinklim) are available on output drivers.
The sinklim mode has the longest propagation delay
and is used to minimize system noise and minimize
power consumption. The f ast and sle wlim modes allow
critical timing to be met.
The drive current is 12 mA sink/6 mA source for the
slewlim and fast output speed selections and
6 mA sink/3 mA source f or the sinklim output. Two adja-
cent outputs can be interconnected to increase the out-
put sink current to 24 mA.
All outputs that are not speed critical should be config-
ured as sinklim to minimize power and noise. The num-
ber of outputs that switch simultaneously in the same
direction should be limited to minimize ground bounce.
To minimize ground bounce problems, locate heavily
loaded output buffers near the ground pads. Ground
bounce is generally a function of the driving circuits,
traces on the PCB, and loads and is best determined
with a circuit simulation.
Outputs can be inverted, and 3-state control signals
can be active-high or active-low. An open-drain output
may be obtained by using the same signal for driving
the output and 3-state signal nets so that the buff er out-
put is enabled only by a low. At powerup, the output
drivers are in slewlim mode, and the input buffers are
configured as TTL-le vel compatible with a pull-up. If an
output is not to be driven in the selected configuration
mode, it is 3-stated.
5 V Tolerant I/O (OR2TxxA)
The I/O on the OR2TxxA series devices allow intercon-
nection to both 3.3 V and 5 V device (selectable on a
per-pin basis) by way of special VDD5 pins that have
been added to the OR2TxxA devices. If any I/O on the
OR2TxxA device interfaces to a 5 V input, then all of
the VDD5 pins must be connected to the 5 V supply. If
no pins on the device interface to a 5 V signal, then the
VDD5 pins must be connected to the 3.3 V supply.
If the VDD5 pins are disconnected (i.e., they are float-
ing), the device will not be damaged; however, the
device may not operate prop er l y until VDD5 is returned
to a proper voltage level. If the VDD5 pins are then
shorted to ground, a large current flow will dev elop, and
the device may be damaged.
PULL-UP
VDD
DELAY
TTL/CMOS
PAD
SLEW RATE POLARITY
DOUT/OUT
PULL-DOWN
dintb, dinlr
in
POLARITY
TRI
5-4591(F)
PULL-UP
VDD
DELAY
PAD
SLEW RATE POLARITY
DOUT/OUT
PULL-DOWN
dintb, dinlr
in
POLARITY
TRI
5-4591.T(F)
Lucent Technologies Inc. 27
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Programmable Input/Output Cells
(continued)
Regardless of the power supply that the VDD5 pins are
connected to (5 V or 3.3 V), the OR2TxxA devices will
drive the pin to the 3.3 V levels when the output buffer
is enabled. If the other device being driven by the
OR2TxxA device has TTL-compatible inputs, then the
device will not dissipate much input buffer power. This
is because the OR2TxxA output is being driven to a
higher level than the TTL level required. If the other
device has a CMOS-compatible input, the amount of
input buffer power will also be small. Both of these
power v alues are dependent upon the input b uff er char-
acteristics of the other device when driven at the
OR2TxxA output buffer voltage levels.
The 2TxxA device has internal programmable pull-ups
on the I/O buffers. These pull-up voltages are always
referenced to VDD. This means that the VDD5 voltage
has no effect on the value of the pull-up voltage at the
pad. This voltage level is always sufficient to pull the
input buff er of the 2TxxA de vice to a high state. The pin
on the 2TxxA device will be at a level 1.0 V below VDD
(minimum of 2.0 V with a minimum VDD of 3.0 V). This
v oltage is sufficient to pull the external pin up to a 3.3 V
CMOS high-input level (1.8 V min) or a TTL high-input
level (2.0 V min) in a 5 V tolerant system, but it will
never pull the pad up to the VDD5 rail. Therefore, in a
5 V tolerant system using 5 V CMOS parts, care must
be taken to evaluate the use of these pull-ups to pull
the pin of the 2TxxA device to a typical 5 V CMOS
high-input level (2.2 V min).
For more information on 5 V tolerant I/Os, please see
ORCA®
Series 5 V Tolerant I/Os
Application Note
(AP99-027FPGA), May 1999.
5 V Tolerant I/O (OR2TxxB)
The I/O on the OR2TxxB Series devices allow intercon-
nection to both 3.3 V and 5 V device (selectable on a
per-pin basis). Unlike the OR2TxxA family, when inter-
faceing into a 5 V signal, it no longer requires a VDD5
supply.
The OR2TxxB de vices will drive the pin to the 3.3 V lev-
els when the output buffer is enabled. If the other
device being driven by the OR2TxxB device has TTL-
compatible inputs, then the device will not dissipate
much input buff er po wer. This is because the OR2TxxB
output is being driven to a higher level than the TTL
level required. If the other device has a CMOS-compat-
ible input, the amount of input buffer power will also be
small. Both of these power v alues are dependent upon
the input buff er characteristics of the other de vice when
driven at the OR2TxxB output buffer voltage levels.
The OR2TxxB device has internal programmable pull-
ups on the I/O buffers. These pull-up voltages are
always referenced to VDD and are always sufficient to
pull the input buffer of the OR2TxxB device to a high
state. The pin on the OR2TxxB device will be at a level
1.0 V below VDD (minimum of 2.0 V with a minimum
VDD of 3.0 V). This voltage is sufficient to pull the e xter-
nal pin up to a 3.3 V CMOS high-input level (1.8 V, min)
or a TTL high input level (2.0 V, min) in a 5 V tolerant
system. Therefore, in a 5 V tolerant system using 5 V
CMOS parts, care must be tak en to ev aluate the use of
these pull-ups to pull the pin of the OR2TxxB device to
a typical 5 V CMOS high-input level (2.2 V, min).
PCI Compliant I/O
The I/O on the OR2TxxB Series devices allows compli-
ance with PCI local b us (Rev. 2.1) 5 V and 3.3 V signal-
ing environments. The signaling environment used for
each input buffer can be selected on a per-pin basis.
The selection provides the appropriate I/O clamping
diodes for PCI compliance.
OR2TxxB devices have 5 V tolerant I/Os as previously
explained, but can optionally be selected on a pin-by-
pin basis to be PCI bus 3.3 V signaling compliant (PCI
bus 5 V signaling compliance occurs in 5 V tolerant
operation mode). Inputs may have a pull-up or pull-
down resistor selected on an input for signal stabiliza-
tion and power management. Input signals in a PIO
can be passed to PIC routing on any of three paths,
two general signal paths into PIC routing, and/or a fast
route into the clock routing system.
OR2TxxA series devices are only compliant in 3.3 V
PCI Local Bus (Rev 2.1) signalling environments.
OR2CxxA devices are only compliant in 5 V PCI Local
Bus (Rev 2.1) signalling environments.
28 Lucent Technologies Inc.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
Programmable Input/Output Cells
(continued)
PIC Routing Resources
The PIC routing is designed to route 4-bit wide buses
efficiently. For example, any four consecutive I/O pads
can hav e both their input and output signals routed into
one PLC. Using only PIC routing, either the input or
output data can be routed to/from a single PLC from/to
any eight pads in a row, as in Figure 25.
The connections between PLCs and the I/O pad are
provided by two basic types of routing resources.
These are routing resources internal to the PIC and
routing resources used for PIC-PLC connection.
Figure 26 and Figure 27 show a high-le v el and detailed
view of these routing resources, respectively.
5-4504(F)
Figure 25. Simplified PIC Routing Diagram
The PIC’s name is represented by a two-letter designa-
tion to indicate on which side of the device it is located
followed by a number to indicate in which row or col-
umn it is located. The first letter, P, designates that the
cell is a PIC and not a PLC . The second letter indicates
the side of the array where the PIC is located. The four
sides are left (L), right (R), top (T), and bottom (B). The
individual I/O pad is indicated by a single letter (either
A, B, C , or D) placed at the end of the PIC name. As an
example, PL10A indicates a pad located on the left
side of the array in the tenth row.
Each PIC has four pads and each pad can be config-
ured as an input, an output (3-statable), a direct output,
or a bidirectional I/O. When the pads are used as
inputs, the external signals are provided to the internal
circuitry at IN[3:0]. When the pads are used to provide
direct inputs to the latches/FFs, they are connected
through DIN[3:0]. When the pads are used as outputs,
the internal signals connect to the pads through
OUT[3:0]. When the pads are used as direct outputs,
the output from the latches/flip-flops in the PLCs to the
PIC is designated DOUT[3:0]. When the outputs are
3-statable, the 3-state enable signals are TS[3:0].
Routing Resources Internal to the PIC
For int er -P I C ro ut i ng, t h e PIC co n t ai ns 1 4 lines used t o
route signals around the perimeter of the FPGA. Figure
25 shows these lines running vertically for a PIC
located on the left side. Figure 26 shows the lines run-
ning horizontally for a PIC located at the top of the
FPGA.
PXL Lines. Each PIC has two PXL lines, labeled
PXL[1:0]. Like the XL lines of the PLC, the PXL lines
span the entire edge of the FPGA.
PXH Lines. Each PIC has four PXH lines, labeled
PXH[3:0]. Like the XH lines of the PLC, the PXH lines
span half the edge of the FPGA.
PX2 Lines. There are four PX2 lines in each PIC,
labeled PX2[3:0]. The PX2 lines pass through two adja-
cent PICs before being broken. These are used to
route nets around the perimeter equally a distance of
two or more PICs.
PX1 Lines. Each PIC has four PX1 lines, labeled
PX1[3:0]. The PX1 lines are one PIC long and are
extended to adjacent PICs by enabling CIPs.
PAD D I/O3 4
PXL
2
CK
2
PIC
SWITCHING
MATRIX
PAD C I/O2 4
PAD B I/O1 4
PAD A I/O0 4
PXH
4
PX2
4
PX1
4
PLC X4
4
PLC X1
4
PLC PSW
5
PLC DOUT
4
PLC XL
4
PLC XH
4
PLC X1
4
PLC X4
4
PLC DIN
4
PXL
2
PXH
4
PX2
4
PX1
4
Lucent Technologies Inc. 29
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Programmable Input/Output Cells
(continued)
PIC Arch itectural Desc ripti on
The PIC architecture given in Figure 26 is described
using the following letter references. The figure depicts
a PIC at the top of the array, so inter-PIC routing is hor-
izontal and the indirect PIC-PLC routing is horizontal to
vertical. In some cases, letters are provided in more
than one location to indicate the path of a line.
A.As in the PLCs, the PIC contains a set of lines which
run the length (width) of the array. The PXL lines
connect in the corners of the array to other PXL
lines. The PXL lines also connect to the PIC BIDI,
PIC BIDIH, and LLDR V lines. As in the PLC XL lines,
the PXH lines twist as they propagate through the
PICs.
B.As in the PLCs, the PIC contains a set of lines which
run one-half the length (width) of the arra y. The PXH
lines connect in the corners and in the middle of the
array perimeter to other PXH lines. The PXH lines
also connect to the PIC BIDI, PIC BIDIH, and
LLDRV lines. As in the PLC XH lines, the PXH lines
do not twist as they propagate through the PICs.
C. The PX2[3:0] lines span a length of two PICs before
intersecting with a CIP. The CIP allows the length of
a path using PX2 lines to be extended two PICs.
D. The PX1[3:0] lines span a single PIC before inter-
secting with a CIP. The CIP allows the length of a
path using PX1 lines to be extended by one PIC.
E. These are four dedicated direct output lines con-
nected to the output buffers. The DOUT[3:0] signals
go directly from a PLC latch/FF to an output buffer,
minimizing the latch/FF to pad propagation delay.
F. This is a direct path from the input pad to the PLC
latch/flip-flops in the two rows (columns) adjacent to
PICs. This input allows a reduced setup time. Direct
inputs from the top and bottom PIC rows are
PDINTB[3:0]. Dir ect inpu ts from the left and r ig ht
PIC columns are PDINLR[3:0].
G.The OUT[3:0], TS[3:0], and IN[3:0] signals for each
I/O pad can be routed directly to the adjacent PLC’s
switchi ng lin es.
H.The four TRIDI buffers allow connections from the
pads to the PLC XL lines. The TRIDIs also allow
connections between the PLC XL lines and the
PBIDI lines, which are described in J below.
I. The four TRIDIH buffers allow connections from the
pads to the PLC XH lines. The TRIDIHs also allow
connections between the PLC XH lines and the
pBIDIH lines, which are described in K below.
J. The PBIDI lines (bidi[3:0]) connect the PXL lines,
PXH lines, and the PX1 lines. These are bidirec-
tional in that the path can be from the PXL, PXH, or
PX1 lines to the XL lines, or from the XL lines to the
PXL, PXH, or PX1 lines.
K.The pBIDIH lines (BIDIH[3:0]) connect the PXL
lines, PXH lines, and the PX1 lines. These are bidi-
rectional in that the path can be from the PXL, PXH,
or PX1 lines to the XH lines, or from the XH lines to
the PXL, PXH, or PX1 lines.
L. The LLIN[3:0] lines provide a fast connection from
the I/O pads to the XL and XH lines.
M.This set of CIPs allows the eight X1 lines (four on
each side) of the PLC perpendicular to the PIC to be
connected to either the PX1 or PX2 lines in the PIC.
N.This set of CIPs allows the eight X4 lines (four on
each side) of the PLC perpendicular to the PIC to be
connected to the PX1 lines. This allows fast access
to/from the I/O pads from/to the PLCs.
O.All four of the PLC X4 lines in a group connect to all
f our of the PLC X4 lines in the adjacent PLC through
a CIP. (This differs from the
ORCA
1C
Series in
which two of the X4 lines in adjacent PLCs are
directly connected without any CIPs.)
P
. The long-line driver (LLDR V) line can be driven by
the XSW4 s witching line of the adjacent PLC . To pro-
vide connectivity to the pads, the LLDRV line can
also connect to an y of the four PXH or to one of the
PXL lines. The 3-state enable (TS[i]) for all four I/O
pads can be driven by XSW4, PXH, or PXL lines.
Q.For fast clock routing, one of the four I/O pads in
each PIC can be selected to be driven onto a dedi-
cated clock line. The clock line spans the length
(width) of the PLC array. This dedicated clock line is
typically used as a clock spine. In the PLCs, the
spine is connected to an XL line to provide a clock
branch in the perpendicular direction. Since there is
another clock line in the PIC on the opposite side of
the array, only one of the I/O pads in a given row
(column) can be used to generate a global signal in
this manner, if all PLCs are driven by the signal.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
30 Lucent Technologies Inc.
Programmable Input/Output Cells (continued)
5-2843(F).r8
Figure 26. PIC Architecture
DT DT DT DT
PA PB PC PD
PXL[1]
PXL[0]
PX2[2]
PX2[3]
PX2[0]
PX2[1]
PX1[0]
PX1[1]
PX1[2]
PX1[3]
PXH[1]
PXH[2]
PXH[3]
PXH[0]
B
A
C
D
FE G
Q
PXL[0]
PXL[1]
PX2[0]
PX2[1]
PX2[2]
PX2[3]
PX1[0]
PX1[1]
PX1[2]
PX1[3]
PXH[1]
PXH[2]
PXH[3]
PXH[0]
B
A
C
D
TS0
OUT0
IN0
DOUT0
TS1
OUT1
IN1
DOUT1
TS3
OUT3
IN3
DOUT3
TS2
OUT2
IN2
DOUT2
PIC DETAIL
BIDI3
F
O
N
O
LLDRV
M
I
L
JK
N
D
C
P
Q
M
BIDIH3
BIDIH2
BIDIH1
BIDIH0
BIDI2
BIDI1
BIDI0
LLIN3
LLIN2
LLIN1
LLIN0
P
P
VXL[3]
VXL[2]
VXL[1]
VXL[0]
VX1[7]
VX1[6]
VX1[5]
VX1[4]
VX1[3]
VX1[2]
VX1[1]
VX1[0]
DOUT[3]
DOUT[2]
DOUT[1]
XSW[3]
XSW[2]
XSW[1]
XSW[0]
XSW[4]
DOUT[0]
CKT
VXH[3]
VXH[2]
VXH[1]
VXH[0]
VX4[7]
VX4[6]
VX4[5]
VX4[4]
PDINTB[3]
PDINTB[2]
PDINTB[1]
PDINTB[0]
VX4[3]
VX4[2]
VX4[1]
VX4[0]
PLC-PIC Routing Resources
There is no direct connection between the inter-PIC
lines and the PLC lines. All connections to/from the
PLC must be done through the connecting lines which
are perpendicular to the lines in the PIC. The use of
perpendicular and parallel lines will be clearer if the
PLC and PIC architectures (Figure 23 and Figure 26)
are placed side by side. Twenty-nine lines in the PLC
can be connected to the 15 lines in the PIC.
Multiple connections between the PIC PX1 lines and
the PLC X1 lines are available. These allow buses
placed in any arbitrary order on the I/O pads to be
unscrambled when placed on the PLC X1 lines. Con-
nections are also available between the PIC PX2 lines
and the PLC X1 lines.
There are eight tridirectional (four TRIDI/four TRIDIH)
buffers in each PIC; they can do the following:
■Drive a signal from an I/O pad onto one of the adja-
cent PLC’s XL or XH lines
■Drive a signal from an I/O pad onto one of the two
PXL or four PXH lines in the PIC
■Drive a signal from the PLC XL or XH lines onto one
of the two PXL or four PXH lines in the PIC
■Drive a signal from the PIC PXL or PXH lines onto
one of the PLC XL or XH lines
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 31
Programmable Input/Output Cells
(continued)
Figure 27 shows paths to and from pads and the use of MUX CIPs to connect lines. Detail A shows six MUX CIPs
f or the pad P0 used to construct the net for the 3-state signal. In the MUX CIP, one of six lines is connected to a line
to form the net. In this case, the ts0 signal can be driven by either of the two PXLs, PX1[0], PX1[1], XSW[0], or the
LLDRV lines. Detail B shows the four MUX CIPs used to drive the P1 output. The source line for OUT1 is either
XSW[1], PX1[1], PX1[3], or PX2[2].
5-2843.BL(F).2C.r3
Figure 27. PIC Detail
DT DT DT DT
PA PB PC PD
TS0
OUT0
IN0
DOUT0
TS1
OUT1
IN1
DOUT1
TS3
OUT3
IN3
DOUT3
TS2
OUT2
IN2
DOUT2
PXL[1]
PXL[0]
PX2[2]
PX2[3]
PX2[0]
PX2[1]
PX1[0]
PX1[1]
PX1[2]
PX1[3]
PXH[1]
PXH[2]
PXH[3]
PXH[0]
PXL[1]
PXL[0]
PX2[2]
PX2[3]
PX2[0]
PX2[1]
PX1[0]
PX1[1]
PX1[2]
PX1[3]
PXH[1]
PXH[2]
PXH[3]
PXH[0]
DOUT[0] DOUT[1] DOUT[2] DOUT[3]
XSW[0]
XSW[1]
XSW[2]
XSW[3]
LLDRV
AB
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
32 Lucent Technologies Inc.
Interquad Routing
In all the
ORCA
Series 2 devices , the PLC arr a y is sp lit
into four equal quadrants. In between these quadrants,
routing has been added to route signals between the
quadrants, especially to the quadrant in the opposite
corner. The two types of interquad blocks, vertical and
horizontal, are pitch matched to PICs. Vertical inter-
quad blocks (vIQ) run between quadrants on the left
and right, while horiz ontal interquad blocks (hIQ) run
between top and bottom quadrants. Since hIQ and vIQ
blocks have the same logic, only the hIQ block is
described below.
The interquad routing connects XL and XH lines. It
does not affect local routing (XSW, X1, X4, fast carry),
so local routing is the same, whether PLC-PLC con-
nections cross quadrants or not. There are no connec-
tions to the local lines in the interquad blocks. Figure 28
presents a (not to scale) view of interquad routing.
Figure 28. Interquad Routing
5-4538(F)
vIQ0[4:0]
vIQ1[4:0]
vIQ2[4:0]
vIQ3[4:0]
5555
TMID
BMID
hIQ3[4:0]
hIQ2[4:0]
hIQ1[4:0]
hIQ0[4:0]
5
5
5
5
SEE
DETAIL IN
FIGURE 29
RMID
LMID
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 33
Interquad Routing (continued)
In the hIQ block in Figure 29, the XH lines from one
quadrant connect through a CIP to its counterpart in
the opposite quadrant, creating a path that spans the
PLC array. Since a passive CIP is used to connect the
two XH lines, a 3-state signal can be routed on the two
XH lines in the opposite quadrants, and then they can
be connecte d thro ugh this CIP.
In the hIQ block, the 20 hIQ lines span the array in a
horizontal direction. The 20 hIQ lines consist of four
groups of five lines each. To effectively route nibble-
wide buses, each of these sets of five lines can connect
to only one of the bits of the nibble for both the XH and
XL. For example, hIQ0 lines can only connect to the
XH0 and XL0 lines, and the hIQ1 lines can connect
only to the XH1 and XL1 lines, etc. Buff ers are provided
for routing signals from the XH and XL lines onto the
hIQ lines and from the hIQ lines onto the XH and XL
lines. Therefore, a connection from one quadrant to
another can be made using only two XH lines (one in
each quadrant) and one interquad line.
5-4537(F).r3
Figure 29. hIQ Block Detail
hIQ3[4]
hIQ3[3]
hIQ3[2]
hIQ3[1]
hIQ3[0]
hIQ2[4]
hIQ2[3]
hIQ2[2]
hIQ2[1]
hIQ2[0]
hIQ1[4]
hIQ1[3]
hIQ1[2]
hIQ1[1]
hIQ1[0]
hIQ0[4]
hIQ0[3]
hIQ0[2]
hIQ0[1]
hIQ0[0]
VXH[3]
VXH[2]
VXH[1]
VXH[0]
VXL[3]
VXL[2]
VXL[1]
VXL[0]
VX4[7]
VX4[6]
VX4[5]
VX4[4]
VX1[7]
VX1[6]
VX1[5]
VX1[4]
VX4[7]
VX4[6]
VX4[5]
VX4[4]
VX1[7]
VX1[6]
VX1[5]
VX1[4]
VXH[3]
VXH[2]
VXH[1]
VXH[0]
VXL[3]
VXL[2]
VXL[1]
VXL[0]
hIQ3[4]
hIQ3[3]
hIQ3[2]
hIQ3[1]
hIQ3[0]
hIQ2[4]
hIQ2[3]
hIQ2[2]
hIQ2[1]
hIQ2[0]
hIQ1[4]
hIQ1[3]
hIQ1[2]
hIQ1[1]
hIQ1[0]
hIQ0[4]
hIQ0[3]
hIQ0[2]
hIQ0[1]
hIQ0[0]
CARRY
CARRY
VX4[3]
VX4[2]
VX4[1]
VX4[0]
VX1[3]
VX1[2]
VX1[1]
VX1[0]
VX1[3]
VX1[2]
VX1[1]
VX1[0]
VX4[3]
VX4[2]
VX4[1]
VX4[0]
INT[4]
INT[3]
INT[2]
INT[1]
INT[0]
GSRN
CKB
CKT
INB[4]
INB[3]
INB[2]
INB[1]
INB[0]
GSRN
CKB
CKT
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
34 Lucent Technologies Inc.
Interquad Routing (continued)
Subquad Routing (OR2C40 A/OR2T40A Only)
In the
ORCA
OR2C40A/OR2T40A/OR2T40B, each
quadrant of the device is split into smaller arrays of
PLCs called subquads. Each of these subquads is
made of a 4 x 4 array of PLCs (for a total of 16 per sub-
quadrant), except at the outer edges of array, which
have less than 16 PLCs per subquad. New routing
resources, called subquad lines, have been added
between each adjacent pair of subquads to enhance
the routability of the device. A portion of the center of
the OR2C40A and OR2T40A array is shown in Figure
30, including the subquad blocks containing a 4 x 4
array of PLCs, the interquad routing lines , and the sub-
quad routing lines.
All of the inter-PLC routing resources discussed previ-
ously continue to be routed between a PLC and its
adjacent PLC , even if the two adjacent PLCs are in dif-
ferent subquad blocks. Since the PLC routing has not
been modified for the OR2C40A/OR2T40A architec-
tures, this means that all of the same routing connec-
tions are possible f or these devices as for any other
ORCA
2C series device. In this way, both the
OR2C40A and OR2T40A/OR2T40B are upwardly com-
patible when compared with the ATT2Cxx series
devices. As the inter-PLC routing runs between sub-
quad blocks, it crosses the new subquad lines. When
this happens, CIPs are used to connect the subquad
lines to the X4 and/or the XH lines which lie along the
other axis of the PLC array.
5-4200(F).r5
Figure 30. Subquad Blocks and Subquad Routing
SUBQUAD
(4 x 4 PLCs)
SUBQUAD
(4 x 4 PLCs) SUBQUAD
(4 x 4 PLCs) SUBQUAD
(4 x 4 PLCs)
SUBQUAD
(4 x 4 PLCs)
SUBQUAD
(4 x 4 PLCs)
SUBQUAD
(4 x 4 PLCs)
SUBQUAD
(4 x 4 PLCs) SUBQUAD
(4 x 4 PLCs) SUBQUAD
(4 x 4 PLCs)
SUBQUAD
(4 x 4 PLCs) SUBQUAD
(4 x 4 PLCs) SUBQUAD
(4 x 4 PLCs)
SUBQUAD
(4 x 4 PLCs) SUBQUAD
(4 x 4 PLCs) SUBQUAD
(4 x 4 PLCs)
SEE DETAIL
IN FIGURES 25
AND 26
HORIZONTAL
INTERQUAD
ROUTING
(hIQ)
HORIZONTAL
SUBQUAD
ROUTING
(HSUB)
VERTICAL
SUBQUAD
ROUTING
(VSUB) VERTICAL
INTERQUAD
ROUTING
(vIQ)
Lucent Technologies Inc. 35
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Interquad Routing (continued)
5-4201(F).r4
Figure 31. Horizontal Subquad Routing
Connectivity
The X4 and XH lines make the only connections to the
subquad lines; therefore, the array remains symmetri-
cal and homogeneous. Since each subquad is made
from a 4 x 4 array of PLCs, the distance between sets
of subquad lines is four PLCs, which is also the dis-
tance between the breaks of the X4 lines. Therefore,
each X4 line will cross exactly one set of subquad lines.
Since all X4 lines make the same connections to the
subquad lines that they cross, all X4 lines in the array
have the same connectivity, and the symmetry of the
routing is preserved. Since all XH lines cross the same
number of subquad blocks, the symmetry is maintained
for the XH lines as well.
The new subquad lines travel a length of eight PLCs
(seven PLCs on the outside edge) before they are bro-
ken. Unlike other inter-PLC lines, they cannot be con-
nected end-to-end. As shown in Figure 30, some of the
horizontal (vertical) subquad lines have connectivity to
the subquad to the left of (above) the current subquad,
while others have connectivity to the subquad to the
right (below). This allows connections to/from the cur-
rent subquad from/to the PLCs in all subquads that sur-
round it.
Between all subquads, including in the center of the
array, there are three groups of subquad lines where
each group contains four lines. Figure 31 shows the
connectivity of these three groups of subquad lines
(HSUB) to the VX4 and VXH lines running between a
vertical pair of PLCs. Between each vertical pair of
subquad blocks, four of the bloc ks shown in Figure 31
are used, one for each pair of vertical PLCs.
The first two groups, depicted as A and B, have con-
nectivity to only one of the two sets of X4 lines between
pairs of PLCs. Since they are very lightly loaded, they
are very fast. The third group, C, connects to both
groups of X4 lines between pairs of PLCs, as well as all
of the XH lines between pairs of PLCs, providing high
fle xibility. The connectivity f or the vertical subquad rout-
ing (Vsub) is the same as described above for the hori-
zontal subquad routing, when rotated onto the other
axis.
At the center row and column of each quadrant, a
fourth group of subquad lines has been added. These
subquad lines only have connectivity to the XH lines.
The XH lines are also broken at this point, which
means that each XH line travels one-half of the quad-
rant (i.e., one-quarter of the device) before it is broken
by a CIP. Since the XH lines can be connected end-to-
end, the resulting line can be either one-quarter, one-
half , three-quarters, or the entire length of the array.
The connectivity of the XH lines and this f ourth group of
subquad lines, indicated as D, are detailed in Figure
32. Again, the connectivity for the vertical subquad
routing (VSUB) is the same as the horizontal subquad
routing, when rotated onto the other axis.
5-4202(F).r3
Figure 32. Horizontal Subquad Routing
Connectivity (Half Quad)
A
C
B
HSUB[11]
HSUB[10]
HSUB[9]
HSUB[8]
HSUB[7]
HSUB[6]
HSUB[5]
HSUB[4]
HSUB[3]
HSUB[2]
HSUB[1]
HSUB[0]
HSUB[11]
HSUB[10]
HSUB[9]
HSUB[8]
HSUB[7]
HSUB[6]
HSUB[5]
HSUB[4]
HSUB[3]
HSUB[2]
HSUB[1]
HSUB[0]
VX4[7]
VX4[6]
VX4[5]
VX4[4]
VX4[3]
VX4[2]
VX4[1]
VX4[0]
VX4[3]
VX4[2]
VX4[1]
VX4[0]
VX4[7]
VX4[6]
VX4[5]
VX4[4]
VX4[3]
VX4[2]
VX4[1]
VX4[0]
VX4[3]
VX4[2]
VX4[1]
VX4[0]
A
D
B
HSUB[11]
HSUB[10]
HSUB[9]
HSUB[8]
HSUB[15]
HSUB[14]
HSUB[13]
HSUB[12]
HSUB[3]
HSUB[2]
HSUB[1]
HSUB[0]
HSUB[11]
HSUB[10]
HSUB[9]
HSUB[8]
HSUB[15]
HSUB[14]
HSUB[13]
HSUB[12]
HSUB[3]
HSUB[2]
HSUB[1]
HSUB[0]
VX4[7]
VX4[6]
VX4[5]
VX4[4]
VX4[3]
VX4[2]
VX4[1]
VX4[0]
VX4[3]
VX4[2]
VX4[1]
VX4[0]
VX4[7]
VX4[6]
VX4[5]
VX4[4]
VX4[3]
VX4[2]
VX4[1]
VX4[0]
VX4[3]
VX4[2]
VX4[1]
VX4[0]
C
HSUB[7]
HSUB[6]
HSUB[5]
HSUB[4]
HSUB[7]
HSUB[6]
HSUB[5]
HSUB[4]
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
36 Lucent Technologies Inc.
Interquad Routing (continued)
PIC Interquad (MID) Routing
Between the PICs in each quadrant, there is also con-
nectivity between the PIC routing and the interquad
routing. These blocks are called LMID (left), TMID
(top), RMID (right), and BMID (bottom). The TMID rout-
ing is shown in Figure 33. As with the hIQ and vIQ
bloc ks, the only connectivity to the PIC routing is to the
global PXH and PXL line s.
The PXH lines from the one quadrant can be con-
nected through a CIP to its counterpart in the opposite
quadrant, providing a path that spans the arra y of PICs.
Since a passive CIP is used to connect the two PXH
lines, a 3-state signal can be routed on the two PXH
lines in the opposite quadrants, and then connected
through this CIP. As with the hIQ and vIQ blocks, CIPs
and buff ers allow nibb le-wide connections between the
interqu ad lines, the XH lines, and the XL lines.
5-4201(F).r4
Figure 33. Top (TMID) Routing
PXL[1]
PXL[0]
PX4[3]
PX4[2]
PX4[1]
PX4[0]
PX1[3]
PX1[2]
PX1[1]
PX1[0]
VIQ0[0]
PXH[2]
PXH[1]
PXH[0]
HX4[3]
HX4[2]
HX4[1]
HX4[0]
VIQ1[0]
VIQ2[0]
VIQ3[0]
PXH[3]
PXL[1]
PXL[0]
PX4[3]
PX4[2]
PX4[1]
PX4[0]
PX1[3]
PX1[2]
PX1[1]
PX1[0]
PXH[2]
PXH[1]
PXH[0]
HX4[3]
HX4[2]
HX4[1]
HX4[0]
PXH[3]
Lucent Technologies Inc. 37
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Programmable Corner Cells
Programmable Rout ing
The programmable corner cell (PCC) contains the cir-
cuitry to connect the routing of the two PICs in each
corner of the device. The PIC PX1 and PX2 lines are
directly connected together from one PIC to another.
The PIC PXL lines are connected from one block to
another through tridirectional buffers. Four CIPs in
each corner connect the four PXH lines from each side
of the device.
Special- P ur pose Functions
In addition to routing functions, special-purpose func-
tions are located in each FPGA corner. The upper-left
PCC contains connections to the boundary-scan logic.
The upper-right PCC contains connections to the read-
back logic and the connectivity to the global 3-state
signal (TS_ALL). The lower-left PCC contains connec-
tions to the internal oscillator.
The lower-right PCC contains connections to the start-
up and global reset logic. During configuration, the
RESET input pad always initiates a configuration abort,
as described in the FPGA States of Operation section.
After configuration, the global set/reset signal (GSRN)
can either be disabled (the default), directly connected
to the RESET input pad, or sourced by a lower-right
corner signal. If the RESET input pad is not used as a
global reset after configuration, this pad can be used as
a normal input pad. During start-up, the release of the
global set/reset, the release of the I/Os, and the
release of the external DONE signal can each be timed
individually based upon the start-up clock. The start-up
clock can come from CCLK or it can be routed into the
start-up block using the lower-right corner routing
resources. More details on start-up can be f ound in the
FPGA States of Operation section.
Clock Distribution Network
The
ORCA
Series 2 clock distribution schemes use pri-
mary and secondary clocks. This provides the system
designer with additional flexibility in assigning clock
input pin s.
One advantage is that board-level clock traces routed
to the FPGA are shorter. On a PC board, the added
length of high-speed clock traces routed to dedicated
clock input pins can significantly increase the parasitic
impedances. The primary advantage of the
ORCA
clock distribution is the availability of a large number of
clocks, since all I/O pins are configurable as clocks.
Primary Clock
The primary clock distribution is shown in Figure 34. If
the clock signal is from an I/O pad, it can be driv en onto
a clock line. The clock lines do not provide clock signals
directly to the PFU; they act as clock spines from which
clocks are branched to XL lines. The XL lines then feed
the clocks to PFUs. A multiplexer in each PLC is used
to transition from the clock spine to the branch.
For a clock spine in the horizontal direction, the inputs
into the multiplex er are the two lines from the left and
right PICs (CKL and CKR) and the local clock line from
the perpendicular direction (HCK). This signal is then
buffered and driven onto one of the vertical XL lines,
f orming the branches. The same structure is used for a
clock spine in the vertical direction. In this case, the
multiplexer selects from lines from the top and bottom
PICs (CKT, CKB, and VCK) and drives the signal onto
one of the horizontal XL lines.
Figure 34 illustrates the distribution of the low-skew pri-
mary clock to a large number of loads using a main
spine and branches. Each row (column) has two dedi-
cated clock lines originating from PICs on opposite
sides of the array. The clock is input from the pads to
the dedicated clock line CKT to form the cloc k spine
(see Figure 34, Detail A). From the clock spine, net
branches are routed using horizontal XL lines and then
PLC clock inputs are tapped from the XL lines, as
shown in Figure 34, Detail B.
38 Lucent Technologies Inc.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
Clock Distribution Network (continued)
5-4480(F).r3
Figure 34. Primary Clock Distribution
Secondary Clock
There are times when a primary clock is either not
available or not desired, and a secondary clock is
needed. For example:
■Only one input pad per PIC can be placed on the
clock routing. If a second input pad in a given PIC
requires global signal routing, a secondary clock
route must be used.
■Since there is only one branch driver in each PLC f or
either direction (vertical and horizontal), both clock
lines in a particular row or column (CKL and CKR, for
example) cannot drive a branch. Therefore, tw o
clocks should not be placed into I/O pads in PICs on
the opposite sides of the same row or column if glo-
bal clocks are to be used.
■Since the clock lines can only be driven from input
pads, internally generated clocks should use second-
ary clock routi ng.
Figure 35 illustrates the secondary clock distribution. If
the clock signal originates from either the left or right
side of the FPGA, it can be routed through the TRIDI
buffers in the PIC onto one of the adjacent PLC’s hori-
zontal XL lines. If the clock signal originates from the
top or bottom of the FPGA, the vertical XL lines are
used for routing. In either case, an XL line is used as
the clock spine. In the same manner, if a clock is only
going to be used in one quadrant, the XH lines can be
used as a clock spine. The routing of the clock spine
from the input pads to the VXL (VXH) using the BIDIs
(BIDIHs) is shown in Figure 35, Detail A.
In each PLC, a low-skew connection through a long-
line driver can be used to connect a horizontal XL line
to a vertical XL line or vice versa. As shown in Figure
35, Detail B , this is used to route the branches from the
clock spine. If the clock spine is a vertical XL line, then
the branches are horizontal XL lines and vice versa.
The clock is then routed into each PLC from the XL line
clock branches.
To minimize skew, the PLC clock input for all PLCs
must be connected to the branch XL lines, not the
spine XL line. Even in PLCs where the clock is routed
from the spine to the branches, the clock should be
routed back into the PLC from the clock branch.
If the clock is to drive only a limited number of loads,
the PFUs can be connected directly to the clock spine.
In this case, all flip-flops driven by the clock must be
located in the same row or column.
CKTCKB
HXL
HCK
R7C8
HCK
DETAIL B
R7C7
HXL
CLOCK
BRANCH CLOCK
SPINES
PLC R1C8
PLC R18C8
PIC PT8
CLOCK SPINE
CKT
DETAIL A
ABCD
CLOCK
CLOCK SP INE
SEE DETAIL A SEE DETAIL B
CLK P IN
BRANCHES
DT DT DT DT
Lucent Technologies Inc. 39
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Clock Distribution Network (continued)
Alternatively, the clock can be routed from the spine to
the branches by using the BIDIs instead of the long-line
driv ers . This results in added dela y in the clock net, but
the clock skew is approximately equal to the clock
routed using the long-line drivers. This method can be
used to create a clock that is used in only one quad-
rant. The XH lines act as a clock spine, which is then
routed to perpendicular XH lines (the branches) using
the BIDIHs.
Clock signals, such as the output of a counter , can also
be generated in PLCs and routed onto an XL line,
which then acts as a clock spine. Although the clock
can be generated in any PLC, it is recommended that
the clock be lo cat ed as clos e to th e cent er o f th e F PGA
as possible to minimize clock skew.
Selecting Clock Input Pins
Any user I/O pin on an
ORCA
FPGA can be used as a
v ery fast, low-ske w clock input. Choosing the first clock
pin is completely arbitrary, but using a pin that is near
the center of an edge of the device (as shown in Fig-
ures 34 and 35) will provide the lowest skew clock net-
work. The pin-to-pin timing numbers in the Timing
Characteristics section of this data book assume that
the clock pin is in one of the four PICs at the center of
any side of the device.
Once the first clock pin has been chosen, there are
only two sets of pins (within the center f our PICs on
each side of the device) that should not be chosen as
the second clock pin: a pin from the same PIC, and/or a
pin from the PIC on the exact opposite edge of the die
(i.e., if a pin from a PIC on the top edge is chosen for
the first clock, the same PIC on the bottom edge should
not be chosen for the second clock).
These rules should be f ollowed iteratively until a total of
eight clocks (or other global signals) have been
selected: four from the left/right sides of the de vice, and
four from the top/bottom sides of the device. If more
than eight clocks are needed, then select another pin
outside the center four PICs to use primary-clock rout-
ing, use secondary clock routing for any pin, or use
local clock routing.
If it is desired to use a pin for one of the first eight
clocks that is not within the center four PICs of any side
of the device and primary clock routing is desired, the
pad names (see Pin Information) of the two clock pins
on the top or bottom of the device cannot be a multi-
plier of four PICs away. The same rule applies to clock
pins on the left or right side of the device.
The following equation can be used to determine pin
names:
Pad number = P[RL][TB]n ± (i x 4)[A – D]
Where i = 1—8, and n is the current PIC number.
For more information, please refer to
Utilizing the
ORCA
®
OR2C/TxxA Clock Distribution Network
Appli-
cation Note (AP97-055FPGA).
5-4481(F).r2
Figure 35. Secondary Clock Distribution
DTDTDTDT
CLOCK
CLOCK SPINE
SEE DETAIL ASEE DETAIL B
CLK PIN
BRANCHES
PFU
HCK
VCK
DETAIL B
PA PB
VXL[3]
VXL[2]
VXL[1]
VXL[0]
VXH[3]
VXH[2]
VXH[1]
VXH[0]
DETAIL A
PC PD
40 Lucent Technologies Inc.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
FPGA States of Operation
Prior to becoming operational, the FPGA goes through a
sequence of states, including initialization, configuration,
and start -up. Fig ure 36 outlines t hes e three FPGA
states.
5-4529(F).r6
Figure 36. FPGA States of Operation
Initialization
Upon powerup, the device goes through an initialization
process. First, an internal power-on-reset circuit is trig-
gered when power is applied. When VDD reaches the
v oltage at which portions of the FPGA begin to operate
(2.5 V to 3 V for the OR2CxxA, 2.2 V to 2.7 V for the
OR2TxxA/OR2TxxB), the I/Os are configured based on
the configuration mode, as determined by the mode
select inputs M[2:0]. A time-out delay is initiated when
VDD reaches between 3.0 V and 4.0 V (OR2CxxA) or
2.7 V to 3.0 V (OR2TxxA/2TxxB) to allow the power
supply v oltage to stabilize. The INIT and DONE outputs
are low. At powerup, if VDD does not rise from 2.0 V to
VDD in less than 25 ms, the user should delay configu-
ration by inputting a low into INIT, PRGM, or RESET
until VDD is greater than the recommended minimum
operating voltage (4.75 V for OR2CxxA commercial
devices and 3.0 V for OR2TxxA/B devices).
At the end of initialization, the default configuration
option is that the configuration RAM is written to a low
state. This prevents shorts prior to configuration. As a
configuration option, after the first configuration (i.e., at
reconfiguration), the user can reconfigure without
clearing the internal configuration RAM first.
The active-low, open-drain initialization signal INIT is
released and must be pulled high by an external resis-
tor when initialization is complete. To synchronize the
configuration of multiple FPGAs, one or more INIT pins
should be wire-ANDed. If INIT is held low by one or
more FPGAs or an external device, the FPGA remains
in the initialization state. INIT can be used to signal that
the FPGAs are not yet initialized. After INIT goes high
for two internal cloc k cycles, the mode lines (M[3:0])
are sampled and the FPGA enters the configuration
state.
The high during configuration (HDC), low during config-
uration (LDC), and DONE signals are active outputs in
the FPGA’ s initialization and configuration states. HDC ,
LDC, and DONE can be used to provide control of
external logic signals such as reset, bus enable, or
PROM enable during configuration. For parallel master
configuration modes, these signals provide PROM
enable control and allow the data pins to be shared
with user logic signals.
If configurati on has begun, an asserti on of RESE T or
PRGM initiates an abort, returning the FPGA to the ini-
tialization state. The PRGM and RESET pins must be
pulled back high before the FPGA will enter the config-
uration state. During the start-up and operating states,
only the assertion of PRGM causes a reconfiguration.
In the master configuration modes, the FPGA is the
source of configuration clock (CCLK). In this mode, the
initialization state is extended to ensure that, in daisy-
chain operation, all daisy-chained slave devices are
ready. Independent of diff erences in clock rates, master
mode devices remain in the initialization state an addi-
tional six internal clock cycles after INIT goes high.
When configuration is initiated, a counter in the FPGA
is set to 0 and begins to count configuration clock
cycles applied to the FPGA. As each configuration data
frame is supplied to the FPGA, it is internally assem-
bled into data words. Each data word is loaded into the
internal configuration memory. The configuration load-
ing process is complete when the internal length count
equals the loaded length count in the length count field,
and the required end of configuration frame is written.
– ACTIVE I/O
– RELEASE INT ERNAL RESET
– DONE GOES HIGH
START-UP
INITIALIZATION
CONFIGURATION RESET
OR
PRGM
LOW
PRGM
LOW
– CLEAR CONFIGURATION MEMORY
– INIT LOW, HDC HIGH, LDC LOW
OPERATION
POWERUP
– POWER-ON TIME DELAY
– M[3:0] MODE IS SELECTED
– CONFIGURATION DATA FRAME WRITTEN
– INIT HIGH, HDC HIGH, LDC LOW
– DOUT ACTIVE
YES
NO NO
RESET,
INIT,
OR
PRGM
LOW
BIT
ERROR YES
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 41
FPGA States of Operation (continued)
5-4482(F)
Figure 37. Initialization/Configuration/Start-Up Waveforms
INITIALIZATION CONFIGURATION
START-UP
OPERATION
VDD
RESET
PRGM
INIT
M[3:0]
CCLK
HDC
LDC
DONE
USER I/O
INTERNAL
RESET
(gsm)
All OR2CxxA I/Os operate as TTL inputs during config-
uration (OR2TxxA/OR2TxxB I/Os are CMOS-only). All
I/Os that are not used during the configuration process
are 3-stated with internal pull-ups. During configura-
tion, the PLC latch/FFs are held set/reset and the inter-
nal BIDI buffers are 3-stated. The TRIDIs in the PICs
are not 3-stated. The combinatorial logic begins to
function as the FPGA is configured. Figure 37 shows
the general wa vef orm of the initialization, configuration,
and start-up states.
Configuration
The
ORCA
Series FPGA functionality is determined by
the state of internal configuration RAM. This configura-
tion RAM can be loaded in a number of different
modes. In these configuration modes, the FPGA can
act as a master or a slave of other devices in the sys-
tem. The decision as to which configuration mode to
use is a system design issue. The next section dis-
cusses configuration in detail, including the configura-
tion data format and the configuration modes used to
load the configuration data in the FPGA.
42 Lucent Technologies Inc.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
FPGA States of Operation (continued)
Start-Up
After configuration, the FPGA enters the start-up
phase. This phase is the transition between the config-
uration and operational states and begins when the
number of CCLKs received after INIT goes high is equal
to the value of the length count field in the configuration
frame and when the end of configuration frame has
been written. The system design issue in the start-up
phase is to ensure the user I/Os become active without
inadvertently activating devices in the system or caus-
ing bus contention. A second system design concern is
the timing of the release of global set/reset of the PLC
latches/FFs.
There are configuration options that control the relative
timing of three e vents: DONE going high, release of the
set/reset of internal FFs, and user I/Os becoming
active. Figure 38 shows the start-up timing for both the
ORCA
and ATT3000 Series FPGAs. The system
designer determines the relative timing of the I/Os
becoming active, DONE going high, and the release of
the set/reset of internal FFs. In the
ORCA
Series
FPGA, the three events can occur in any arbitrary
sequence. This means that they can occur before or
after each other, or they can occur simultaneously.
There are four main start-up modes: CCLK_NOSYNC ,
CCLK_SYNC, UCLK_NOSYNC, and UCLK_SYNC.
The only difference between the modes starting with
CCLK and those starting with UCLK is that f or the
UCLK modes, a user clock must be supplied to the
start-up logic. The timing of start-up events is then
based upon this user clock, rather than CCLK. The dif-
ference between the SYNC and NOSYNC modes is
that, for SYNC mode, the timing of two of the start-up
events (release of the set/reset of internal FFs and the
I/Os becoming active) is triggered by the rise of the
e xternal DONE pin f ollowed by a variable number of ris-
ing clock edges (either CCLK or UCLK). For the
NOSYNC mode, the timing of these two events is
based only on either CCLK or UCLK.
DONE is an open-drain bidirectional pin that may
include an optional (enabled by def ault) pull-up resistor
to accommodate wired ANDing. The open-drain DONE
signals from multiple FPGAs can be tied together
(ANDed) with a pull-up (internal or external) and used
as an activ e-high ready signal, an active-low PROM
enable, or a reset to other portions of the system.
When used in SYNC mode, these ANDed DONE pins
can be used to synchronize the other two start-up
events, since they can all be synchronized to the same
external signal. This signal will not rise until all FPGAs
release their DONE pins, allowing the signal to be
pulled high.
The default for
ORCA
is the CCLK_SYNC synchro-
nized start-up mode where DONE is released on the
fir st CCLK rising edge, C1 (see Fi gure 38). Since thi s is
a synchronized start-up mode, the open-drain DONE
signal can be held low e xternally to stop the occurrence
of the other two start-up events. Once the DONE pin
has been released and pulled up to a high lev el, the
other two start-up events can be programmed individu-
ally to either happen immediately or after up to four ris-
ing edges of CCLK (Di, Di + 1, Di + 2, Di + 3, Di + 4).
The default is for both events to happen immediately
after DONE is rele ased and pul le d high.
A commonly used design technique is to release
DONE one or more clock cycles bef ore allowing the I/O
to become active. This allows other configuration
devices, such as PROMs, to be disconnected using the
DONE signal so that there is no bus contention when
the I/Os become active. In addition to controlling the
FPGA during start-up, other start-up techniques that
avoid contention include using isolation devices
between the FPGA and other circuits in the system,
reassigning I/O locations and maintaining I/Os as
3-stated outputs until contentions are resolved.
Each of these start-up options can be selected during
bit stream generation in
ORCA
Foundry, using
Advanced Options. For more information, please see
the
ORCA
Foundry documentation.
Reconfiguration
To reconfigure the FPGA when the device is operating
in the system, a low pulse is input into PRGM. The con-
figuration data in the FPGA is cleared, and the I/Os not
used for configuration are 3-stated. The FPGA then
samples the mode select inputs and begins reconfigu-
ration. When reconfiguration is complete, DONE is
released, allowing it to be pulled high.
Lucent Technologies Inc. 43
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
FPGA States of Operation (continued)
5-2761(F).r4
Figure 38. Start-Up Waveforms
Par t i a l R econf iguration
All
ORCA
device families have been designed to allow
a partial reconfiguration of the FPGA at any time. This
is done by setting a bit stream option in the previous
configuration sequence that tells the FPGA to not reset
all of the configuration RAM during a reconfiguration.
Then only the configuration frames that are to be modi-
fied need to be rewritten, thereby reducing the configu-
ration time.
Other bit stream options are also available that allow
one portion of the FPGA to remain in operation while a
partial reconfiguration is being done. If this is done, the
user must be careful to not cause contention between
the two configurations (the bit stream resident in the
FPGA and the partial reconfiguration bit stream) as the
second re co nfi guration bit stre am is being loa ded .
Other Configuration Options
Configuration options used during device start-up were
previously discussed in the FPGA States of Operation
section of this data sheet. There are many other config-
uration options availab l e to the user that can be set
during bit stream generation in
ORCA
Foundry. These
include options to enable boundary scan, readback
options, and options to control and use the internal
oscillator after configuration.
Other useful options that affect the next configuration
(not the current configuration process) include options
to disable the global set/reset during configuration, dis-
able the 3-state of I/Os during configuration, and dis-
able the reset of internal RAMs during configuration to
allow f or partial configurations (see abov e). For more
information on how to set these and other configuration
options, please see the
ORCA
Foundry documenta-
tion.
Configuration Data Format
The
ORCA
Foundry Development System interfaces
with front-end design entry tools and pro vides the tools
to produce a fully configured FPGA. This section dis-
cusses using the
ORCA
F oundry Development System
to generate configuration RAM data and then provides
the details of the configuration frame format.
The
ORCA
Series 2 series of FPGAs are enhanced
v ersions of the
ORCA
ATT2Cxx/ATT2Txx architectures
that provide upward bit stream compatibility for both
series of devices as well as with each other.
Di
F
DONE
ATT3000
I/O
GLOBAL
RESET
C1 C2 C3 C4
F
C1 C2 C3 C4
C1 C2 C3 C4
C1, C2, C3, OR C4
Di + 1Di Di + 2 Di + 3 Di + 4
Di + 1Di Di + 2 Di + 3 Di + 4
ORCA
CCLK_SYNC
DONE IN
U1 U2 U3 U4
F
U1 U2 U3 U4
U1 U2 U3 U4
ORCA
UCLK_NOSYNC
Di + 1Di Di + 2 Di + 3 Di + 4
Di + 1 Di + 2 Di + 3
ORCA
UCLK_SYNC
UCLK PERIOD
SYNCHRONIZATION UNCERTAINTY
DONE IN
F
C1
C1 U1, U2, U3, OR U4
DONE
I/O
GSRN
ACTIVE
DONE
I/O
GSRN
ACTIVE
DONE
I/O
GSRN
ACTIVE
DONE
I/O
GSRN
ACTIVE
UCLK
F = finished, no more CLKs required.
CCLK PERIOD
F
ORCA
CCLK_NOSYNC
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
44 Lucent Technologies Inc.
Configuration Data Format (continued)
Using
ORCA
Foundry to Generate
Configuration RAM Data
The configuration data defines the I/O functionality,
logic, and interconnections. The bit stream is gener-
ated by the development system. The bit stream cre-
ated by the bit stream generation tool is a series of 1s
and 0s used to write the FPGA configuration RAM. The
bit stream can be loaded into the FPGA using one of
the configuration modes discussed later. In the bit
stream generator, the designer selects options which
affect the FPGA’s functionality. Using the output of the
bit stream generator, circuit.bit, the development sys-
tem’s download tool can load the configuration data
into the
ORCA
series FPGA evaluation board from a
PC or workstation. Alternatively, a user can program a
PROM (such as the ATT1700A Series Serial ROM or a
standard EPROM) and load the FPGA from the PROM.
The development system’s PROM programming tool
produces a file in .mks or .exo format.
Configuration Data Frame
A detailed description of the frame f ormat is shown in
Figure 39. The header frame begins with a series of 1s
and a preamble of 0010, followed by a 24-bit length
count field representing the total number of configura-
tion clocks needed to complete the loading of the
FPGAs. Following the header frame is an optional ID
frame. This frame contains data used to determine if
the bit stream is being loaded to the correct type of
ORCA
FPGA (i.e., a bit stream generated for an
OR2C15A is being sent to an OR2C15A). Since the
OR2CxxA devices are bit stream compatible with the
ATT2Cxx, ATT2Tx x, OR2 Txx A, a nd OR2T xxB famili es,
a bit stream from any of these devices will not cause an
error when loaded into an OR2CxxA, OR2TxxA, or
OR2TxxB device. The ID frame has a secondary func-
tion of optionally enabling the parity checking logic for
the rest of the data frames.
The configuration data frames follo w . Each frame starts
with a 0 start bit and ends with three or more 1 stop
bits. F ollowing each start bit are four control bits: a pro-
gram bit, set to 1 if this is a data frame; a compress bit,
set to 1 if this is a compressed frame; and the opar and
epar parity bits (see Bit Stream Error Checking). An
11-bit address field that determines in which column
the FPGA is to be written is followed by alignment and
write control bits. For uncompressed frames, the data
bits needed to write one column in the FPGA are next.
F or compressed frames, the data bits from the pre vious
frame are sent to a different FPGA column, as speci-
fied by the new address bits; therefore, new data bits
are not required. When configuration of the current
FPGA is finished, an end-of-configuration frame (where
the program bit is set to 0) is sent to the FPGA. The
length and number of data frames and information on
the PROM size for the Series 3 FPGAs are given in
Tab le 7.
Table 7. Configuration Frame Size
Devices OR2C/
2T04A OR2C/
2T06A OR2C/
2T08A OR2C/
2T10A OR2C/
2T12A OR2C/
2T15A/B OR2C/
2T26A OR2C/
2T40A/B
# of Frames 480 568 656 744 832 920 1096 1378
Data Bits/Frame 110 130 150 170 190 210 250 316
Configuration Data
(# of frames x # of data bits/frame) 52,800 73,840 98,400 126,480 158,080 193,200 274,000 435,448
Maxim um Tot al # Bit s/Frame
(align bits, 1 write bit, 8 s top bits) 136 160 176 200 216 240 280 344
Maximum Configuration Data
(# bits x # of frames) 65,280 90,880 115,456 148,800 179,712 220,800 306,880 474,032
Maximum PROM Size (bits)
(add 48-bit header, ID fram e, and
40-bit end of configuration frame)
65,504 91,128 115,720 149,088 180,016 221,128 307,248 474,464
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 45
Configuration Data Format (continued)
The data frames for all the Series 2 series devices are given in Table 8. An alignment field is required in the slave
parallel mode for the uncompressed format. The alignment field (shown by [A]) is a series of 0s: five for the
OR2C06A/OR2T06A, OR2C10A/OR2T10A, OR2C15A/OR2T15A/OR2T15B, and OR2C26A/OR2T26A; three for
the OR2C40A/OR2T40A/OR2T40B; and one for the OR2C04A/OR2T04A, OR2C08A/OR2T08A, and OR2C12A/
OR2T12A. The alignment field is not required in any other mode.
Table 8. Configuration Data Frames
5-4530(F)
Figure 39. Serial Configuration Data Format
OR2C04A/OR2T04A
Uncompressed 010 opar epar [addr10:0] [A]1[Data109:0]111
Compres sed 011 opar epar [addr1 0:0] 111
OR2C06A/OR2T06A
Uncompressed 010 opar epar [addr10:0] [A]1[Data129:0]111
Compres sed 011 opar epar [addr1 0:0] 111
OR2C08A/OR2T08A
Uncompressed 010 opar epar [addr10:0] [A]1[Data149:0]111
Compres sed 011 opar epar [addr1 0:0] 111
OR2C10A/OR2T10A
Uncompressed 010 opar epar [addr10:0] [A]1[Data169:0]111
Compres sed 011 opar epar [addr1 0:0] 111
OR2C12A/OR2T12A
Uncompressed 010 opar epar [addr10:0] [A]1[Data189:0]111
Compres sed 011 opar epar [addr1 0:0] 111
OR2C15A/OR2T15A/OR2T15B
Uncompressed 010 opar epar [addr10:0] [A]1[Data209:0]111
Compres sed 011 opar epar [addr1 0:0] 111
OR2C26A/OR2T26A
Uncompressed 010 opar epar [addr10:0] [A]1[Data249:0]111
Compres sed 011 opar epar [addr1 0:0] 111
OR2C40A/OR2T40A/OR2T40B
Uncompressed 010 opar epar [addr10:0] [A]1[Data315:0]111
Compres sed 011 opar epar [addr1 0:0] 111
EIGHT 1s 0010
24-bit
LENGTH
COUNT POSTAMBLE
LEADING HEADER
D ATA FRAMES
FPGA # 1 D ATA FRAMES
FPGA # 2
END OF
CONFIGURATION
FRAME
FPGA #1
END OF
CONFIGURATION
FRAME
FPGA #2
PREAMBLE
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
46 Lucent Technologies Inc.
Configuration Data Format (continued)
Table 9. Configuration Frame Format and Contents
Note: For slave parallel mode, the byte containing the preamble must be 11110010. The number of leading header dummy bits must
be (n * 8) + 4, where n is any nonnegative integer and the number of trailing dummy bits must be (n * 8), where n is any positive
integer. The number of stop bits/frame for slave parallel mode must be (x * 8), where x is a positive intege r. Note also that the bit
stream generator tool supplies a bit stream which is compatible with all configuration modes, including slave parallel mode.
Header
11111111 Leading header—4 bits minimum dummy bits
0010 Preamble
24-Bit Length Count Configuration frame length
1111 Trailing header—4 bits minimum dummy bits
ID Frame
(Optional)
0 Frame start
P—1 Must be set to 1 to indicate data frame
C—0 Must be set to 0 to indicate uncompressed
Opar, Epar Frame pari ty bit s
Addr[10:0] =
11111111111 ID frame address
Prty_En Set to 1 to enable parity
Reserved [42:0] Reserved bits set to 0
ID 20-bit part ID
111 Three or more stop bits (high) to separate frames
Configuration
Data
Frame
(repeated for
each data frame)
0 Frame start
P—1 or 0 1 indicates data frame; 0 indicates all frames are written
C—1 or 0 Uncompressed—0 indicates data and address are supplied;
Compressed—1 indicates only address is supplied
Opar, Epar Frame pari ty bit s
Addr[10:0] Column address in FPGA to be written
A Alignment bit (different number of 0s needed for each part)
1 Write bit—used in uncompressed data frame
Data Bits Needed only in an uncompressed data frame
..
..
111 One or more stop bits (high) to separate frames
End of
Configuration 0010011111111111 16 bits—00 indicates all frames are written
Postamble 111111 . . . . . Additional 1s
Lucent Technologies Inc. 47
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Bit Stream Error Checking
There are three different types of bit stream error
checking performed in the
ORCA
Series 2 FPGAs:
ID frame, frame alignment, and parity checking.
An optional ID data frame can be sent to a specified
address in the FPGA. This ID frame contains a unique
code for the part it was generated for which is com-
pared within the FPGA. Any differences are flagged as
an ID error. This frame is automatically created by the
bit stream generation program in
ORCA
Foundry.
Every data frame in the FPGA begins with a start bit
set to 0 and three or more stop bits set to 1. If any of
the three previous bits were a 0 when a start bit is
encountered, it is flagged as a frame alignment error.
Parity checking is also done on the FPGA for each
frame, if it has been enabled by setting the prty_en bit
to 1 in the ID frame. This is set by enabling the parity
check option in the bit stream generation program of
ORCA
Foundry. Two parity bits, opar and epar, are
used to check the parity of bits in alternating bit posi-
tions to even parity in each data frame. If an odd num-
ber of ones is found for either the even bits (starting
with the start bit) or the odd bits (starting with the pro-
gram bit), then a parity error is flagged.
When any of the three possible errors occur , the FPGA
is f orced into the INIT state, forcing INIT low. The FPGA
will remain in this state until either the RESET or PRGM
pins are asserted.
FPGA Configuration Modes
There are eight methods for configuring the FPGA.
Seven of the configuration modes are selected on the
M0, M1, and M2 inputs. The eighth configuration mode
is accesse d through the boun dary-scan inte r face. A
fourth input, M3, is used to select the frequency of the
internal oscillator, which is the source for CCLK in
some configuration modes. The nominal frequencies of
the internal oscillator are 1.25 MHz and 10 MHz. The
1.25 MHz frequency is selected when the M3 input is
unconnected or driven to a high state.
There are three basic FPGA configuration modes:
master, slave, and peripheral. The configuration data
can be transmitted to the FPGA serially or in parallel
bytes. As a master, the FPGA provides the control sig-
nals out to strobe data in. As a slave device, a clock is
generated externally and provided into CCLK. In the
peripheral mode, the FPGA acts as a microprocessor
peripheral. Table 10 lists the functions of the configura-
tion mode pins.
Table 10. Configuration Modes
Master Parallel Mode
The master parallel configuration mode is generally
used to interface to industry-standard byte-wide mem-
ory, such as the 2764 and larger EPROMs. Figure 40
provides the connections f or master parallel mode. The
FPGA outputs an 18-bit address on A[17:0] to memory
and reads one byte of configuration data on the rising
edge of RCLK. The parallel bytes are internally serial-
ized starting with the least significant bit, D0.
5-4483(F)
Figure 40. Master Parallel Configuration Schematic
There are two parallel master modes: master up and
master down. In master up, the starting memory
address is 00000 Hex and the FPGA increments the
address for each byte loaded. In master down, the
starting memory address is 3FFFF Hex and the FPGA
decrements the address.
One master mode FPGA can interface to the memory
and provide configuration data on DOUT to additional
FPGAs in a daisy chain. The configuration data on
DOUT is provided synchronously with the falling edge
of CCLK. The frequency of the CCLK output is eight
times that of RCLK.
M2 M1 M0 CCLK Configuration
Mode Data
0 0 0 Output Master Serial
0 0 1 Input Slave Parallel Parallel
010Reserved
0 1 1 Input Sync Per ipheral Parallel
1 0 0 Output Master (up) Parallel
1 0 1 Output Async Peripheral Paral lel
1 1 0 Output Master (down) Parallel
1 1 1 Input Slave Serial
TO DAISY-
CHAINED
DEVICES
DOUT
CCLK
HDC
LDC
RCLK
A[17:0]
D[7:0]
DONE
PRGM
M2
M1
M0
A[17:0]
D[7:0]
OE
CE
PROGRAM VDD
VDD OR GND
EPROM
ORCA
SERIES
FPGA
48 Lucent Technologies Inc.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
FPGA Configuration Modes (continued)
Master Serial Mode
In the master serial mode, the FPGA loads the configu-
ration data from an ex ternal serial ROM. The configura-
tion data is either loaded automatically at start-up or on
a PRGM command to reconfigure. The ATT1700 and
ATT1700A Series can be used to configure the FPGA
in the master serial mode. This provides a simple 4-pin
interface in an 8-pin package. The ATT1736, ATT1765,
and ATT17128 serial ROMs store 32K, 64K, and 128K
bits, respectively.
Configuration in the master serial mode can be done at
powerup and/or upon a configure command. The sys-
tem or the FPGA must activate the serial ROM's
RESET/OE and CE inputs. At powerup, the FPGA and
serial ROM each contain internal power-on reset cir-
cuitry that allows the FPGA to be configured without
the system providing an external signal. The power-on
reset circuitry causes the serial ROM's internal address
pointer to be reset. After powerup, the FPGA automati-
cally enters its initialization phase.
The serial ROM/FPGA interf ace used depends on such
factors as the availability of a system reset pulse, avail-
ability of an intelligent host to generate a configure
command, whether a single serial ROM is used or mul-
tiple serial ROMs are cascaded, whether the serial
ROM contains a single or multiple configuration pro-
grams, etc. Because of differing system requirements
and capabilities, a single FPGA/serial ROM interf ace is
generally not appropriate for all applications.
Data is read in the FPGA sequentially from the serial
ROM. The DATA output from the serial ROM is con-
nected directly into the DIN input of the FPGA. The
CCLK output from the FPGA is connected to the
CLOCK input of the serial R OM. During the configura-
tion process, CCLK clocks one data bit on each rising
edge.
Since the data and clock are direct connects, the
FPGA/serial ROM design task is to use the system or
FPGA to enable the RESET/OE and CE of the serial
ROM(s). There are several methods for enabling the
serial ROM’s RESET/OE and CE inputs. The serial
ROM's RESET/OE is programmable to function with
RESET active-high and OE act ive-low or RESET active-
low and OE active-high.
In Figure 41, serial ROMs are cascaded to configure
multiple daisy-chained FPGAs. The host generates a
500 ns low pulse into the FPGA's PRGM input. The
FPGA’s INIT input is connected to the serial ROM’s
RESET/OE input, which has been programmed to
function with RESET active-low and OE active-high.
The FPGA DONE is routed to the CE pin. The low on
DONE enables the serial ROMs. At the completion of
configuration, the high on the FPGA's DONE disables
the serial ROM.
Serial ROMs can also be cascaded to support the con-
figuration of multiple FPGAs or to load a single FPGA
when configuration data requirements e xceed the
capacity of a single serial ROM. After the last bit from
the first serial ROM is read, the serial ROM outputs
CEO low and 3-states the DATA output. The next serial
ROM recognizes the low on CE input and outputs con-
figuration data on the DATA output. After configuration
is complete, the FPGA’s DONE output into CE disab les
the serial ROMs.
This FPGA/serial ROM interface is not used in applica-
tions in which a serial ROM stores multiple configura-
tion programs. In these applications, the next
configuration program to be loaded is stored at the
ROM location that follows the last address for the previ-
ous configuration program. The reason the interface in
Figure 41 will not work in this application is that the low
output on the INIT signal would reset the serial ROM
address pointer, causing the first configuration to be
reloaded.
In some applications, there can be contention on the
FPGA's DIN pin. Dur ing con fig uration, DIN recei ves
configuration data, and after configuration, it is a user
I/O. If there is contention, an early DONE at start-up
(selected in
ORCA
Foundry) may correct the prob lem.
An alternative is to use LDC to drive the serial ROM's
CE pin. In order to reduce noise, it is generally better to
run the master serial configuration at 1.25 MHz (M3 pin
tied high), rather than 10 MHz, if possible.
Figure 41. Master Serial Configuration Schematic
ATT1700A
DIN
M2
M1
M0
ORCA
SERIES
FPGA
CCLK
DOUT
TO DAISY-
CHAINED
DEVICES
DATA
CLK
CE
CEO
ATT1700A
DATA
CLK
RESET/OE
CEO
CE
TO MORE
SERIAL ROMs
AS NEEDED
DONE
INIT
PROGRAM
RESET/OE
PRGM
5-4456.1(F)
Lucent Technologies Inc. 49
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
FPGA Configuration Modes (continued)
Asynchr onous Peripheral Mode
Figure 42 shows the connections needed for the asyn-
chronous peripheral mode. In this mode, the FPGA
system interface is similar to that of a microprocessor-
peripheral interface. The microprocessor generates the
control signals to write an 8-bit byte into the FPGA. The
FPGA control inputs include active-low CS0 and active-
high CS1 chip selects, a write WR input, and a read RD
input. The chip selects can be cycled or maintained at
a static level during the configuration cycle. Each byte
of data is written into the FPGA’s D[7:0] input pins.
The FPGA provides a RDY status output to indicate
that another byte can be loaded. A low on RDY indi-
cates that the double-buffered hold/shift registers are
not ready to receive data, and this pin must be moni-
tored to go high before another byte of data can be
written. The shortest time RDY is low occurs when a
byte is loaded into the hold register and the shift regis-
ter is empty, in which case the b yte is immediately
transferred to the shift register. The longest time for
RDY to remain low occurs when a byte is loaded into
the holding register and the shift register has just
started shifting configuration data into configuration
RAM.
The RDY status is also available on the D7 pin by
enabling the chip selects, setting WR high, and apply-
ing RD low, where the RD input is an output enable f or
the D7 pin when RD is low. The D[6:0] pins are not
enabled to drive when RD is low and, thus, only act as
input pins in asynchronous peripheral mode.
5-4484(F)
Figure 42. Asynch ronous Peripheral Configuration
Schematic
Synchronous Peripheral Mode
In the synchronous peripheral mode, byte-wide data is
input into D[7:0] on the rising edge of the CCLK input.
The first data byte is clocked in on the second CCLK
after INIT goes high. Subsequent data bytes are
clocked in on every eighth rising edge of CCLK. The
RDY signal is an output which acts as an acknowledge.
RDY goes high one CCLK after data is clocked and,
after one CCLK cycle, returns low. The process repeats
until all of the data is loaded into the FPGA. The data
begins shifting on DOUT 1.5 cycles after it is loaded in
parallel. It requires additional CCLKs after the last byte
is loaded to complete the shifting. Figure 43 shows the
connections for synchronous peripheral mode.
As with master modes, the peripheral modes can be
used as the lead FPGA for a daisy chain of slave
FPGAs.
5-4486(F)
Figure 43. Synchronous Peripheral Configuration
Schematic
TO DAISY-
CHAINED
DEVICES
DOUT
CCLK
HDC
LDC
VDD
ORCA
SERIES
FPGA
MICRO-
PROCESSOR ADDRESS
DECODE LOGIC
BUS
CONTROLLER
PRGM
D[7:0]
RDY/BUSY
INIT
DONE
CS0
CS1
RD
WR
M2
M1
M0
8
TO DAISY-
CHAINED
DEVICES
DOUT
HDC
LDC
ORCA
SERIES
FPGA
MICRO-
PROCESSOR
PRGM
D[7:0]
M2
M1
M0
8
+5 V
CCLK
RDY/BUSY
INIT
50 Lucent Technologies Inc.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
FPGA Configuration Modes (continued)
Slave Serial Mode
The slave serial mode is primarily used when multiple
FPGAs are configured in a daisy chain. The serial
slav e serial mode is also used on the FPGA ev aluation
board which interfaces to the download cab le. A de vice
in the slave serial mode can be used as the lead device
in a daisy chain. Figure 44 shows the connections for
the slave serial configuration mode.
The configuration data is provided into the FPGA’ s DIN
input synchronous with the configuration clock CCLK
input. After the FPGA has loaded its configuration data,
it retransmits the incoming configuration data on
DOUT. CCLK is routed into all slav e serial mode
devices in parallel.
Multiple slave FPGAs can be loaded with identical con-
figurations simultaneously. This is done by loading the
configuration data into the DIN inputs in parallel.
5-4485(F)
Figure 44. Slave Serial Configuration Schematic
Slave Parallel Mode
The slave parallel mode is essentially the same as the
slav e serial mode e xcept that 8 bits of data are input on
pins D[7:0] for each CCLK cycle. Due to 8 bits of data
being input per CCLK cycle, the DOUT pin does not
contain a valid bit stream for slave parallel mode. As a
result, the lead device cannot be used in the slave
parallel mode in a daisy-chain configuration.
Figure 45 is a schematic of the connections for the
slave parallel configuration mode. WR and CS0 are
active-low chip select signals, and CS1 is an active-
high chip select signal. These chip selects allow the
user to configure multiple FPGAs in slave parallel
mode using an 8-bit data bus common to all of the
FPGAs. These chip selects can then be used to select
the FPGA(s) to be configured with a given bit stream,
but once an FPGA has been selected, it cannot be
deselected until it has been completely programmed.
5-4487(F)
Figure 45. Slave Parallel Configuration Schematic
MICRO-
PROCESSOR
OR
DOWNLOAD
CABLE
M2
M1
M0
HDC
SERIES
FPGA
LDC
VDD
CCLK
PRGM
DOUT
TO DAISY-
CHAINED
DEVICES
DONE
DIN
INIT
ORCA
MICRO-
PROCESSOR
OR
SYSTEM
D[7:0]
DONE
CCLK
CS1
M2
M1
M0
HDC
LDC
8
VDD
INIT
PRGM
CS0
WR
SERIES
FPGA
ORCA
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 51
FPGA Configuration Modes (continued)
Daisy Chain
Multiple FPGAs can be configured by using a daisy
chain of the FPGAs. Daisy chaining uses a lead FPGA
and one or more FPGAs configured in slave serial
mode. The lead FPGA can be configured in any mode
e xcept slav e parallel mode. (Daisy chaining is not avail-
able with the boundary - sc an ram_w instruction , dis-
cussed later.)
All daisy-chained FPGAs are connected in series.
Each FPGA reads and shifts the preamble and length
count in on positive CCLK and out on negative CCLK
edges.
An upstream FPGA that has received the preamble
and length count outputs a high on DOUT until it has
received the appropriate number of data frames so that
downstream FPGAs do not receive frame start bits
(0s). After loading and retransmitting the preamb le and
length count to a daisy chain of slave devices, the lead
device loads its configuration data fr ames. The loading
of configuration data continues after the lead device
has received its configuration data if its internal frame
bit counter has not reached the length count. When the
configuration RAM is full and the number of bits
received is less than the length count field, the FPGA
shifts any additional data out on DOUT.
The configuration data is read into DIN of slav e de vices
on the positive edge of CCLK, and shifted out DOUT
on the negative edge of CCLK. Figure 46 shows the
connections for loading multiple FPGAs in a daisy-
chain configuration.
The generation of CCLK for the daisy-chained devices
which are in slav e serial mode diff ers depending on the
configuration mode of the lead device. A master paral-
lel mode device uses its internal timing generator to
produce an internal CCLK at eight times its memory
address rate (RCLK). The asynchronous peripheral
mode device outputs eight CCLKs for each write cycle.
If the lead device is configured in either synchronous
peripheral or a slave mode, CCLK is routed to the lead
device and to all of the daisy-chained devices.
The development system can create a composite
configuration bit stream for configuring daisy-chained
FPGAs. The frame f ormat is a preamb le , a length count
for the total bit stream, multiple concatenated data
frames, an end-of-configuration frame per device, a
postamble, and an additional fill bit per device in the
serial chain.
As seen in Figure 46, the INIT pins for all of the FPGAs
are connected together. This is required to guarantee
that powerup and initialization will work correctly. In
general, the DONE pins for all of the FPGAs are also
connected together as shown to guarantee that all of
the FPGAs enter the start-up state simultaneously. This
may not be required, depending upon the start-up
sequence desired.
5-4488(F)
Figure 46. Daisy-Chain Configuration Schematic
VDD
EPROM
PROGRAM
D[7:0]
OE
CE
A[17:0] A[17:0]
D[7:0]
DONE
M2
M1
M0
DONE
HDC
LDC
RCLK
CCLK
DOUT DIN DOUT DIN
CCLK
DONE
DOUT
INIT INIT INIT
CCLK
VDD
VDD OR
GND
PRGM PRGM
M2
M1
M0
PRGM
M2
M1
M0
VDD VDD
HDC
LDC
RCLK
HDC
LDC
RCLK
VDD
ORCA
SERIES
FPGA
SLAVE #2
ORCA
SERIES
FPGA
MASTER
ORCA
SERIES
FPGA
SLAVE #1
52 Lucent Technologies Inc.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
Special Function Blocks
Special function blocks in the Series 2 provide e xtra
capabilities bey ond general FPGA operation. These
blocks reside in the corners of the FPGA array.
Single Fu ncti on Blocks
Most of the special function blocks perform a specific
dedicated function. These functions are data/configura-
tion readback control, global 3-state control (TS_ALL),
internal oscillator generation, global set/reset (GSRN),
and start-up logic.
Readback Logic
The readback logic is loca ted in the upper rig ht corner
of the FPGA.
Readback is used to read back the configuration data
and, optionally, the state of the PFU outputs. A read-
back operation can be done while the FPGA is in nor-
mal system operation. The readback operation cannot
be daisy-chained. To use readback, the user selects
options in the bit stream generator in the
ORCA
Foundry Development System.
Tab l e 11 provides readback options selected in the bit
stream generator tool. The table provides the number
of times that the configuration data can be read back.
This is intended primarily to give the user control over
the security of the FPGA’s configuration program. The
user can prohibit readback (0), allow a single readback
(1), or allow unrestricted readback (U).
Table 11. Readback Options
The pins used for readback are readback data
(RD_DATA), read configuration (RD_CFG), and configu-
ration clock (CCLK). A readback oper ation is initiated
by a high-to-low transition on RD_CFG. The RD_CFG
input must remain low during the readback operation.
The readbac k operation can be restarted at frame 0 by
dri ving the RD_CFG pin high, applying at least two ris -
ing edges of CCLK, and then driving RD_CFG low
again. One bit of data is shifted out on RD_DATA at the
rising edge of CCLK. The first start bit of the readback
frame is transmitted out several cycles after the first ris-
ing edge of CCLK after RD_CFG is input low (see Tab le
48, Readback Timing Characteristics in the Timing
Characteristics section).
It should be noted that the RD_DATA output pin is also
used as the dedicated boundary-scan output pin, TDO.
If this pin is being used as TDO, the RD_DATA output
from readback can be routed internally to any other pin
desired. The RD_CFG input pin is also used to control
the global 3-state (TS_ALL) function. Before and during
configuration, the TS_ALL signal is always driven by
the RD_CFG input and readback is disabled. After con-
figuration, the selection as to whether this input drives
the readback or global 3-state function is determined
by a set of bit stream options. If used as the RD_CFG
input for readback, the internal TS_ALL input can be
routed internally to be driven by any input pin.
The readback frame contains the configuration data
and the state of the internal logic. During readback, the
value of all five PFU outputs can be captured. The fol-
lowing options are allowed when doing a capture of the
PFU outputs.
1. Do not capture data (the data written to the capture
RAMs, usually 0, will be read back).
2. Capture data upon entering readback.
3. Capture data based upon a configurable signal
internal to the FPGA. If this signal is tied to
logic 0, capture RAMs are written continuously.
4. Capture data on either options 2 or 3 above.
The readback frame has a similar, but not identical, for-
mat to the configuration frame. This eases a bitwise
comparison between the configuration and readback
data. The readback data is not inverted. Ev ery data
frame has one low start bit and one high stop bit. The
preamble, including the length count field, is not part of
the readback frame. The readback frame contains
states in locations not used in the configuration. These
locations need to be masked out when comparing the
configuration and readback frames. The development
system optionally provides a readback bit stream to
compare to readback from the FPGA. Also note that if
any of the LUTs are used as RAM and ne w data is writ-
ten to them, these bits will not hav e the same values as
the original configuration data frame either.
Option Function
0 Prohibit Readback
1 Allow One Readback Only
U Allow Unrestricted Number of Readbacks
Lucent Technologies Inc. 53
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Special Function Blocks (continued)
Global 3-State Control (TS_ALL)
The TS_ALL block resides in the upper-right corner of
the FPGA array.
To increase the testability of the
ORCA
Series FP G As,
the global 3-state function (TS_ALL) disables the
device. The TS_ALL signal is driven from either an
external pin or an internal signal. Before and during
configuration, the TS_ALL signal is driven by the input
pad RD_CFG. After configuration, the TS_ALL signal
can be disabled, driven from the RD_CFG input pad, or
driv en by a general routing signal in the upper-right cor-
ner. Before configuration, TS_ALL is active-low; after
configuration, the sense of TS_ALL can be inverted.
The follo wing occur when TS_ALL is activated:
1. All of the user I/O output buffers are 3-stated, the
user I/O input buffers are pulled up (with the pull-
down disabled), and the input buffers are configured
with TTL input thresholds (OR2CxxA only).
2. The TDO/RD_DATA output buffer is 3-stated.
3. The RD_CFG, RESET, and PRGM input buff ers remain
active with a pull-up.
4. The DONE output buffer is 3-stated, and the input
buffer is pulled-up.
Internal Oscillator
The internal oscillator resides in the lower-left corner of
the FPGA array. It has output clock frequencies of
1.25 MHz and 10 MHz. The internal oscillator is the
source of the internal CCLK used for configuration. It
may also be used after configuration as a general-
purpose clock signal.
Global Set/Reset (GSRN)
The GSRN logic resides in the lower-right corner of the
FPGA. GSRN is an inv ertible , def ault, activ e-low signal
that is used to reset all of the user-accessible latches/
FFs on the device. GSRN is automatically asserted at
powerup and during configuration of the device.
The timing of the release of GSRN at the end of config-
uration can be programmed in the start-up logic
described below. Following configuration, GSRN may
be connected to the RESET pin via dedicated routing,
or it may be connected to any signal via normal routing.
Within each PFU, individual FFs and latches can be
programmed to either be set or reset when GSRN is
asserted.
The RESET input pad has a special relationship to
GSRN. During configuration, the RESET input pad
always initiates a configuration abort, as described in
the FPGA States of Operation section. After configura-
tion, the global set/reset signal (GSRN) can either be
disabled (the default), directly connected to the RESET
input pad, or sourced by a lo wer-right corner signal. If
the RESET input pad is not used as a global reset after
configuration, this pad can be used as a normal input
pad.
Star t-Up Logic
The start-up logic block is located in the lower right cor-
ner of the FPGA. This block can be configured to coor-
dinate the relative timing of the release of GSRN, the
activation of all user I/Os, and the assertion of the
DONE signal at the end of configuration. If a start-up
clock is used to time these events , the start-up clock
can come from CCLK, or it can be routed into the start-
up block using lower-right corner routing resources.
These signals are described in the Start-Up subsection
of the FPGA States of Operation section.
54 Lucent Technologies Inc.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
Special Function Blocks (continued)
Boundary Scan
The increasing complexity of integrated circuits (ICs)
and IC packages has increased the difficulty of testing
printed-circuit boards (PCBs). To address this testing
problem, the
IEEE
standard 1149.1 - 1990 (
IEEE
Stan-
dard Test Access Port and Boundary-Scan Architec-
ture) is implemented in the
ORCA
series of FPGAs. It
allows users to efficiently test the interconnection
between integr ated circuits on a PCB as well as test
the integrated circuit itself. The
IEEE
1149.1 standard
is a well-defined protocol that ensures interoperability
among boundary-scan (BSCAN) equipped devices
from different vendors.
The
IEEE
1149.1 standard defines a test access port
(TAP) that consists of a 4-pin interface with an optional
reset pin for boundary-scan testing of integrated cir-
cuits in a system. The
ORCA
series FPGA provides
four interface pins: test data in (TDI), test mode select
(TMS), test clock (TCK), and test data out (TDO). The
PRGM pin used to reconfigure the device also resets
the boundary-scan logic.
The user test host serially loads test commands and
test data into the FPGA through these pins to drive out-
puts and examine inputs. In the configuration shown in
Figure 47, where boundary scan is used to test ICs,
test data is transmitted serially into TDI of the first
BSCAN device (U1), through TDO/TDI connections
between BSCAN de vices (U2 and U3), and out TDO of
the last BSCAN device (U4). In this configuration, the
TMS and TCK signals are routed to all boundary-scan
ICs in parallel so that all boundary-scan components
operate in the same state. In other configurations, mul-
tiple scan paths are used instead of a single ring. When
multiple scan paths are used, each ring is indepen-
dently controlled by its own TMS and TCK signals.
Figure 48 provides a system interface for components
used in the boundary-scan testing of PCBs. The three
major components shown are the test host, boundary-
scan support circuit, and the devices under test
(DUTs). The DUTs shown here are
ORCA
Series
FPGAs with dedicated boundary-scan circuitry. The
test host is normally one of the follo wing: automatic test
equipment (ATE), a workstation, a PC, or a micropro-
cessor .
Fig.34.a(F).1C
K ey: BSC = boundary-scan cell, BDC = bidirectional data cell,
and DCC = data control cell.
Figure 47. Printed-Circuit Board with Boundary-
Scan Circuitry
The boundary-scan support circuit shown in Figure 48
is the 497AA Boundary-Scan Master (BSM). The BSM
off-loads tasks from the test host to increase test
throughput. To interface between the test host and the
DUTs, the BSM has a general microprocessor interf ace
and provides paralle l- to- serial/ se rial-to- pa rallel conver-
sion, as well as three 8K data buffers.
SCAN
OUT
TDI
TMS
TCK
TDO
U2
SEE EN LARGED VIEW BELOW
PLC
ARRAY
SCAN
IN
TDO TCK TMS TDI
TAPC
BYPASS
REGISTER
INSTRUCTION
REGISTER
BDC
BSC
P_IN
P_OUT
P_TS
SCAN
IN
PT[ij]
ENLARGED VI EW
TDI
TDO
TMS
TCK
U1
TDI
TDO
TMS
TCK
U4
TDI
TDO
TMS
TCK
U3
TDI
TDO
TMS
TCK
net a
net b
net c
s
DCC SCAN
OUT
DCC
BSC
P_IN
P_OUT
P_TS
SCAN
IN
PB[ij]
BDC
SCAN
OUT
BDC
BSC
P_IN
P_OUT
P_TS
PR[ij]
DCC
SCAN
OUT
BSC
P_IN
P_OUT
P_TS
PL[ij]
SCAN
IN
DCC
BDC
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 55
Special Function Blocks (continued)
5-4488(F)
Figure 48. Boundary-Scan Interface
VDD
EPROM
PROGRAM
D[7:0]
OE
CE
A[17:0] A[17:0]
D[7:0]
DONE
M2
M1
M0
DONE
HDC
LDC
RCLK
CCLK
DOUT DIN DOUT DIN
CCLK
DONE
DOUT
INIT INIT INIT
CCLK
VDD
VDD OR
GND
PRGM PRGM
M2
M1
M0
PRGM
M2
M1
M0
VDD VDD
HDC
LDC
RCLK
HDC
LDC
RCLK
VDD
ORCA
SERIES
FPGA
SLAVE #2
ORCA
SERIES
FPGA
MASTER
ORCA
SERIES
FPGA
SLAVE #1
The BSM also increases test throughput with a dedi-
cated automatic test-pattern generator and with com-
pression of the test response with a signature analysis
register. The PC-based boundary-scan test card/soft-
ware allows a user to quickly prototype a boundary-
scan test setup.
Boun dary-Scan In structions
The
ORCA
Series boundary-scan circuitry is used for
three mandatory
IEEE
1149.1 tests (EXTEST, SAM-
PLE/PRELOAD, BYPASS) and four
ORCA
-defined
instructions. The 3-bit wide instruction register sup-
ports the eight instructions listed in Table 12.
Table 12. Boundary-Scan Instructions
The external test (EXTEST) instruction allows the inter-
connections between ICs in a system to be tested for
opens and stuck-at faults. If an EXTEST instruction is
performed for the system shown in Figure 47, the con-
nections between U1 and U2 (shown by nets a, b, and
c) can be tested by driving a value onto the given nets
from one device and then determining whether the
same value is seen at the other device. This is deter-
mined by shifting 2 bits of data f or each pin (one for the
output value and one for the 3-state value) through the
BSR until each one aligns to the appropriate pin.
Then, based upon the value of the 3-state signal, either
the I/O pad is driven to the value given in the BSR, or
the BSR is updated with the input value from the I/O
pad, which allows it to be shifted out TDO.
The SAMPLE instruction is useful for system debug-
ging and fault diagnosis by allowing the data at the
FPGA’s I/Os to be observed during normal operation.
The data for all of the I/Os is captured simultaneously
into the BSR, allowing them to be shifted-out TDO to
the test host. Since each I/O buffer in the PICs is bidi-
rectional, two pieces of data are captured for each I/O
pad: the value at the I/O pad and the value of the
3-state co ntr ol sign al.
Code Instruction
000 EXTEST
001 PLC Scan Ring 1
010 RAM Write (RAM_W)
011 Reserved
100 SAMPLE/PRELOAD
101 PLC Scan Ring 2
110 RAM Read (RAM_R)
111 BYPASS
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
56 Lucent Technologies Inc.
Special Function Blocks (continued)
There are four
ORCA
-defined instructions. The PLC
scan rings 1 and 2 (PSR1, PSR2) allow user-defined
internal scan paths using the PLC latches/FFs. The
RAM_Write Enable (RAM_W) instruction allows the
user to serially configure the FPGA through TDI. The
RAM_Read Enable (RAM_R) allows the user to read
back RAM contents on TDO after configuration.
ORCA
Boundary-Scan Circuitry
The
ORCA
Series boundary-scan circuitry includes a
test access port controller (TAPC), instruction register
(IR), boundary-scan register (BSR), and bypass regis-
ter. It also includes circuitry to support the four pre-
defined instructions.
Figure 49 shows a functional diagram of the boundary-
scan circuitry that is implemented in the
ORCA
series.
The input pins’ (TMS, TCK, and TDI) locations vary
depending on the part, and the output pin is the dedi-
cated TDO/RD_DATA output pad. Test data in (TDI) is
the serial input data. Test mode select (TMS) controls
the boundary-scan test access port controller (TAPC).
Test clock (TCK) is the test clock on the board.
The BSR is a series connection of boundary-scan cells
(BSCs) around the periphery of the IC. Each I/O pad on
the FPGA, e xcept for CCLK, DONE, and the boundary-
scan pins (TCK, TDI, TMS, and TDO), is included in
the BSR. The first BSC in the BSR (connected to TDI)
is located in the first PIC I/O pad on the left of the top
side of the FPGA (PTA PIC). The BSR proceeds clock-
wise around the top, right, bottom, and left sides of the
array. The last BSC in the BSR (connected to TDO) is
located on the top of the left side of the array (PLA3).
The bypass instruction uses a single FF which resyn-
chronizes test data that is not part of the current scan
operation. In a bypass instruction, test data received on
TDI is shifted out of the bypass register to TDO. Since
the BSR (which requires a two FF delay for each pad)
is bypassed, test throughput is increased when devices
that are not part of a test operation are bypassed.
The boundary-scan logic is enabled before and during
configuration. After configuration, a configuration
option determines whether or not boundary-scan logic
is used.
The 32-bit boundary-scan identification register con-
tains the manufacturer’s ID number, unique part num-
ber, and version, but is not implemented in the
ORCA
series of FPGAs. If boundary scan is not used, TMS,
TDI, and TCK become user I/Os, and TDO is 3-stated
or used in the readback operation.
5-2840(C).r7
Figure 49.
ORCA
Series Boundary-Scan Circuitry Functional Diagram
TAP
CONTROLLER
BOUNDARY-SCAN REGISTER
PSR2 REGISTER (PLCs)
BYPASS REGISTER
DATA
MUX
INSTRUCTION DECODER
INSTRUCTION REGISTER
M
U
X
RESET
CLOCK-IR
SHIFT-IR
UPDATE-IR
PUR
TDO
SELECT
ENABLE
RESET
CLOCK-DR
SHIFT-DR
UPDATE-DR
TDI
DATA REGISTERS
PSR1 REGISTER (PLCs)
CONFIGURATION REGISTER
(RAM_R, RAM_W)
I/O BUFFERS
V
DD
TMS
V
DD
TCK
V
DD
PRGM
V
DD
Lucent Technologies Inc. 57
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Special Function Blocks (continued)
ORCA
Series TAP Controller (TAPC)
The
ORCA
Series TAP controller (TAPC) is a 1149.1
compatible test access port controller. The 16 JTAG
state assignments from the
IEEE
1149.1 specification
are used. The TAPC is controlled by TCK and TMS.
The TAPC states are used for loading the IR to allow
three basic functions in testing: providing test stimuli
(Update-DR), test execution (Run-Test/Idle), and
obtaining test responses (Capture-DR). The TAPC
allows the test host to shift in and out both instructions
and test data/results. The inputs and outputs of the
TAPC are provided in the table below. The outputs are
primarily the control signals to the instruction register
and the data register.
Table 13. TAP Controller Input/Outputs
The TAPC generates control signals which allow cap-
ture, shift, and update operations on the instruction and
data registers. In the capture operation, data is loaded
into the register. In the shift operation, the captured
data is shifted out while new data is shifted in. In the
update operation, either the instruction register is
loaded for instruction decode, or the boundary-scan
register is updated for control of outputs.
The test host generates a test by providing input into
the
ORCA
Series TMS input synchronous with TCK.
This sequences the TAPC through states in order to
perform the desired function on the instruction register
or a data register. Figure 50 provides a diagram of the
state transitions for the TAPC. The next state is deter-
mined by the TMS input value.
5-5370(F)
Figure 50. TAP Controller State Transition Diagram
Symbol I/O Function
TMS I Test Mode Select
TCK I Test Clock
PUR I Powerup Reset
PRGM I BSCAN Reset
TRESET O Test Logic Reset
Select O Select IR (high); Select DR (low)
Enable O Test Data Out Enable
Capture-DR O Capture/Parallel Load DR
Capture-IR O Capture/Parallel Load IR
Shift-DR O Shift Data Register
Shift-DR O Shift Instruction Register
Update-DR O Update/Parallel Load DR
Update-IR O Update/Parallel Load IR
SELECT-
DR-SCAN
CAPTURE-DR
SHIFT-DR
EXIT1-DR
PAUSE-DR
EXIT2-DR
UPDATE-DR
1
1
0
0
10
RUN-TEST/
IDLE 1
TEST-LOGIC-
RESET
SELECT-
IR-SCAN
CAPTURE-IR
SHIFT-IR
EXIT1-IR
PAUSE-IR
EXIT2-IR
UPDATE-IR
1
1
0
10
00
0
0
1
0
1
1
1
0
1
1
0
0
0
0
1
11
0
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
58 Lucent Technologies Inc.
Special Function Blocks (continued)
Boundary-Scan Cells
Figure 51 is a diagram of the boundary-scan cell (BSC)
in the
ORCA
series PICs. There are four BSCs in each
PIC: one for each pad, except as noted above. The
BSCs are connected serially to form the BSR. The
BSC controls the functionality of the in, out, and 3-state
signals for each pad.
The BSC allows the I/O to function in either the normal
or test mode. Normal mode is defined as when an out-
put buffer receives input from the PLC array and pro-
vides output at the pad or when an input buffer
provides input from the pad to the PLC arra y. In the test
mode, the BSC executes a boundary-scan operation,
such as shifting in scan data from an upstream BSC in
the BSR, providing test stimuli to the pad, capturing
test data at the pad, etc.
The primary functions of the BSC are shifting scan data
serially in the BSR and observing input (P_IN), output
(P_OUT), and 3-state (P_TS) signals at the pads. The
BSC consists of two circuits: the bidirectional data cell
is used to access the input and output data, and the
direction control cell is used to access the 3-state
value. Both cells consist of a flip-flop used to shift scan
data which f eeds a flip-flop to control the I/O buff er . The
bidirectional data cell is connected serially to the direc-
tion control cell to form a boundary-scan shift register.
The TAPC signals (capture, update, shiftn, treset, and
TCK) and the MODE signal control the operation of the
BSC. The bidirectional data cell is also controlled b y
the high out/low in (HOLI) signal generated by the
direction control cell. When HOLI is low, the bidirec-
tional data cell receives input buffer data into the BSC.
When HOLI is high, the BSC is loaded with functional
data from the PLC.
The MODE signal is generated from the decode of the
instruction register. When the MODE signal is high
(EXTEST), the scan data is propagated to the output
buffer. When the MODE signal is low (BYPASS or
SAMPLE), functional data from the FPGA’s internal
logic is propagated to the output buffer.
The boundary-scan description language (BSDL) is
provided for each de vice in the
ORCA
series of FP GAs.
The BSDL is generated from a device profile, pinout,
and other boundary-scan information.
5-2844(F).r4
Figure 51. Boundary-Scan Cell
DQDQ
DQDQ
SCAN IN
P_OUT
HOLI
BIDIRECTIONAL DATA CELL
I/O BU FFER
DIRECTION CONTROL CELL
MODEUPDATE/TCKSCAN OUTTCKSHIFTN/CAPTURE
P_TS
P_IN PAD_IN
PAD_TS
PAD_OUT
0
1
0
1
0
1
0
1
0
1
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 59
Special Function Blocks (continued)
Fig.5.3(F)
Figure 52. Instruction Register Scan Timing Diagram
Boundary-Scan Timing
To ensure race-free operation, data changes on specific clock edges. The TMS and TDI inputs are clocked in on
the rising edge of TCK, while changes on TDO occur on the falling edge of TCK. In the execution of an EXTEST
instruction, parallel data is output from the BSR to the FPGA pads on the falling edge of TCK. The maximum fre-
quency allowed for TCK is 10 MHz.
Figure 52 shows timing waveforms for an instruction scan operation. The diagram shows the use of TMS to
sequence the TAPC through states. The test host (or BSM) changes data on the falling edge of TCK, and it is
clocked into the DUT on the rising edge.
TEST-LOGIC-RESET
RUN-TEST/IDLE
SELECT-DR-SCAN
CAPTURE-IR
SHIFT-IR
EXIT1-IR
PAUSE-IR
EXIT2-IR
SHIFT-IR
EXIT1-IR
UPDATE-IR
RUN-TEST/IDLE
SELECT-IR-SCAN
TCK
TMS
TDI
60 Lucent Technologies Inc.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
ORCA
Timing Characteristics
To define speed gr ades, the
ORCA
Series pa rt n umb er
designation (see Table 54) uses a single-digit number
to designate a speed grade. This number is not related
to any single ac parameter. Higher numbers indicate a
faster set of timing parameters. The actual speed sort-
ing is based on testing the dela y in a path consisting of
an input buffer, combinatorial delay through all PLCs in
a row, and an output buffer. Other tests are then done
to verify other delay parameters, such as routing
delays, setup times to FFs, etc.
The most accurate timing characteristics are reported
by the timing analyzer in the
ORCA
Foundry Develop-
ment System. A timing report provided by the develop-
ment system after layout divides path delays into logic
and routing delays. The timing analyzer can also pro-
vide logic delays prior to layout. While this allows rout-
ing budget estimates, there is wide variance in routing
delays associated with different layouts.
The logic timing parameters noted in the Electrical
Characteristics section of this data sheet are the same
as those in the design tools. In the PFU timing giv en in
Tables 31—79, symbol names are generally a concate-
nation of the PFU operating mode (as defined in
Tab le 3) and the parameter type. The wildcard charac-
ter (*) is used in symbol names to indicate that the
parameter applies to any sub-LUT. The setup, hold,
and propagation delay parameters, defined below, are
designated in the symbol name by the SET, HLD, and
DEL characters, respectively.
The values given for the parameters are the same as
those used during production testing and speed bin-
ning of the de vices. The junction temperature and sup-
ply voltage used to characterize the devices are listed
in the delay tables. Actual delays at nominal tempera-
ture and voltage f or best-case processes can be much
better than the values given.
It should be noted that the junction temperature used in
the tables is generally 85 °C. The junction temperature
for the FPGA depends on the power dissipated by the
device, the package thermal characteristics (ΘJA), and
the ambient temperature, as calculated in the following
equation and as discussed further in the Package
Thermal Characteristics section:
TJma x = TAmax + (P • ΘJA) °C
Note: The user must determine this junction tempera-
ture to see if the delays from
ORCA
Foundry
should be derated based on the following derat-
ing tables.
Tab le 14A and 14B and provide approximate power
supply and junction temperature derating f or OR2CxxA
commercial and industrial devices. Table 15A and 15B
provides the same information for the OR2TxxA and
OR2TxxB devices (both commercial and industrial).
The delay values in this data sheet and reported by
ORCA
Foundry are shown as 1.00 in the tables. The
method for determining the maximum junction temper-
ature is defined in the Thermal Characteristics section.
Taken cumulatively, the range of parameter values for
best-case vs. worst- case processing, supply voltag e,
and junction temperature can approach 3 to 1.
Table 14A. Derating for Commercial Devices
(OR2CxxA)
Table 14B. Derating for Industrial Devices
(OR2CxxA)
Table 15A. Derating for Commercial/Industrial
Devices (OR2TxxA)
TJ
(°C) Power Supply Voltage
4.75 V 5.0 V 5.25 V
00.81 0.79 0.77
25 0.85 0.83 0.81
85 1.00 0.97 0.95
100 1.05 1.02 1.00
125 1.12 1.09 1.07
TJ
(°C) Power Supply Voltage
4.5 V 4.75 V 5.0 V 5.25 V 5.5 V
–40 0.71 0.70 0.68 0.66 0.65
00.80 0.78 0.76 0.74 0.73
25 0.84 0.82 0.80 0.78 0.77
85 1.00 0.97 0.94 0.93 0.91
100 1.05 1.01 0.99 0.97 0.95
125 1.12 1.09 1.06 1.04 1.02
TJ
(°C) Power Supply Voltage
3.0 V 3.3 V 3.6 V
–40 0.73 0.66 0.61
00.82 0.73 0.68
25 0.87 0.78 0.72
85 1.00 0.90 0.83
100 1.04 0.94 0.87
125 1.10 1.00 0.92
Lucent Technologies Inc. 61
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
ORCA
Timing Characteristics
(continued)
Table 15B. Derating for Commercial/Industrial
Devices (OR2TxxB)
Note: The derating tables shown above are for a typical critical path
that contains 33% logic delay and 66% routing delay. Since the
routing delay derates at a higher rate than the logic delay, paths
with more than 66% routing dela y will derate at a higher rate
than shown in the table. The approximate derating values vs.
temperature are 0.26% per °C for logic delay and 0.45% per °C
for routing delay. The approximate derating values vs. voltage
are 0.13% per mV for both logic and routing delays at 25 °C.
In addition to supply voltage, process variation, and
operating temperature, circuit and process improve-
ments of the
ORCA
series FPGAs over time will result
in significant improvement of the actual performance
over those listed for a speed grade. Even though lower
speed grades may still be available, the distribution of
yield to timing parameters may be several speed bins
higher than that designated on a product brand. Design
practices need to consider best-case timing parame-
ters (e.g., delays = 0), as well as worst-case timing.
The routing delays are a function of fan-out and the
capacitance associated with the CIPs and metal inter-
connect in the path. The number of logic elements that
can be driven (or fan-out) by PFUs is unlimited,
although the delay to reach a valid logic level can
exceed timing requirements. It is difficult to make accu-
rate routing dela y estimates prior to design compilation
based on fan-out. This is because the CAE software
may delete redundant logic inserted by the designer to
reduce fan-out, and/or it ma y also automatically reduce
fan-out by net splitting.
The waveform test points are given in the Measure-
ment Conditions section of this data sheet. The timing
parameters given in the electrical characteristics tables
in this data sheet follow industry practices, and the val-
ues they reflect are described below.
■Propagation Dela y—the time between the specified
reference points. The delays provided are the worst
case of the tphh and tpll delays for noninverting func-
tions, tplh and tphl for inverting functions, and tphz
and tplz for 3-state enable.
■Setup Time—the interval immediately preceding the
transition of a clock or latch enable signal, during
which the data must be stable to ensure it is recog-
nized as the intende d value.
■Hold Time—the interval immediately following the
transition of a clock or latch enable signal, during
which the data must be held stable to ensure it is rec-
ognized as the intended value.
■3-state Enable—the time from when a TS[3:0] signal
becomes active and the output pad reaches the high-
impedance state.
Estimating Power Dissipation
OR2CxxA
The total operating power dissipated is estimated by
summing the standby (IDDSB), internal, and external
power dissipated. The internal and external power is
the power consumed in the PLCs and PICs, respec-
tively. In general, the standby power is small and may
be neglected. The total operating power is as follows:
PT = Σ PPLC + Σ PPIC
The internal operating power is made up of two parts:
clock generation and PFU output power. The PFU out-
put power can be estimated based upon the number of
PFU outputs s witching when driving an av erage fan-out
of two:
PPFU = 0.16 mW/MHz
For each PFU output that switches, 0.16 mW/MHz
needs to be multiplied times the frequency (in MHz)
that the output s witches. Generally, this can be esti-
mated by using one-half the clock rate, multiplied by
some activity fa ctor; for example, 20%.
The power dissipated by the clock generation circuitry
is based upon four parts: the fixed clock power, the
po wer/clock br an c h row or co lu mn , t h e c lo ck po w e r di s -
sipated in each PFU that uses this particular clock, and
the power from the subset of those PFUs that is config-
ured in either of the two synchronous modes (SSPM or
SDPM). Therefore, the clock power can be calculated
for the four parts using the following equations:
OR2C04A Clock Power
P = [0.62 mW/MHz
+ (0.22 mW/MHz – Branch) (# Branches)
+ (0.022 mW/MHz – PFU) (# PFUs)
+ (0.006 mW/MHz – SMEM_PFU)
(# SMEM_PFUs)] fCLK
For a quick estimate, the worst-case (typical circuit)
OR2C04 A clock power ≈ 3.9 mW/MHz.
TJ
(°C) Power Supply Voltage
3.0 V 3.15 V 3.3 V 3.45 V 3.6 V
–40 0.81 0.78 0.76 0.74 0.73
00.86 0.83 0.80 0.77 0.76
25 0.9 0.87 0.83 0.8 0.78
85 1.0 0.95 0.93 0.88 0.86
100 1.02 0.98 0.95 0.91 0.88
125 1.06 1.03 0.98 0.95 0.92
62 Lucent Technologies Inc.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
Estimating Power Dissipation (continued)
OR2C06A Clock Power
P = [0.63 mW/MHz
+ (0.25 mW/MHz – Branch) (# Branches)
+ (0.022 mW/MHz – PFU) (# PFUs)
+ (0.006 mW/MHz – SMEM_PFU)
(# SMEM_PFUs)] fCLK
For a quick estimate, the worst-case (typical circuit)
OR2C06A clock power ≈ 5.3 mW/MHz.
OR2C08A Clock Power
P = [0.65 mW/MHz
+ (0.29 mW/MHz – Branch) (# Branches)
+ (0.022 mW/MHz – PFU) (# PFUs)
+ (0.006 mW/MHz – SMEM_PFU)
(# SMEM_PFUs)] fCLK
For a quick estimate, the worst-case (typical circuit)
OR2C08A clock power ≈ 6.6 mW/MHz.
OR2C10A Clock Power
P = [0.66 mW/MHz
+ (0.32 mW/MHz – Branch) (# Branches)
+ (0.022 mW/MHz – PFU) (# PFUs)
+ (0.006 mW/MHz – SMEM_PFU)
(# SMEM_PFUs)] fCLK
For a quick estimate, the worst-case (typical circuit)
OR2C10A clock power ≈ 8.6 mW/MHz.
OR2C12A Clock Power
P = [0.68 mW/MHz
+ (0.35 mW/MHz – Branch) (# Branches)
+ (0.022 mW/MHz – PFU) (# PFUs)
+ (0.006 mW/MHz – SMEM_PFU)
(# SMEM_PFUs)] fCLK
For a quick estimate, the worst-case (typical circuit)
OR2C12A clock power ≈ 10.5 mW/MHz.
OR2C15A Clock Power
P = [0.69 mW/MHz
+ (0.38 mW/MHz – Branch) (# Branches)
+ (0.022 mW/MHz – PFU) (# PFUs)
+ (0.006 mW/MHz – SMEM_PFU)
(# SMEM_PFUs)] fCLK
For a quick estimate, the worst-case (typical circuit)
OR2C15A clock power ≈ 12.7 mW/MHz.
OR2C26A Clock Power
P = [0.73 mW/MHz
+ (0.44 mW/MHz – Branch) (# Branches)
+ (0.022 mW/MHz – PFU) (# PFUs)
+ (0.006 mW/MHz – SMEM_PFU)
(# SMEM_PFUs)] fCLK
For a quick estimate, the worst-case (typical circuit)
OR2C26A clock power ≈ 17.8 mW/MHz.
OR2C40A Clock Power
P = [0.77 mW/MHz
+ (0.53 mW/MHz – Branch) (# Branches)
+ (0.022 mW/MHz – PFU) (# PFUs)
+ (0.006 mW/MHz – SMEM_PFU)
(# SMEM_PFUs)] fCLK
For a quick estimate, the worst-case (typical circuit)
OR2C40A clock power ≈ 26.6 mW/MHz.
The power dissipated in a PIC is the sum of the power
dissipated in the four I/Os in the PIC. This consists of
power dissipated by inputs and ac power dissipated by
outputs. The power dissipated in each I/O depends on
whether it is configured as an input, output, or input/
output. If an I/O is operating as an output, then there is
a power dissipation component for PIN, as well as
POUT. This is because the output feeds back to the
input.
The p owe r dissip ated b y a TTL in put b uff er is e stimat ed
as:
PTTL = 2.2 mW + 0.17 mW/MHz
The power dissipated by an input buffer is estimated
as:
PCMOS = 0.17 mW/MHz
The ac power dissipation from an output or bidirec-
tional is estimated by the following:
POUT = (CL + 8.8 pF) x VDD2 x F Watts
where the unit for CL is farads, and the unit for F is Hz.
As an example of estimating power dissipation,
suppose that a fully utilized OR2C15A has an average
of three outputs f or each of the 400 PFUs, that all
20 clock branches are used, that 150 of the 400 PFUs
hav e FFs clock ed at 40 MHz (16 of which are operating
in a synchronous memory mode), and that the PFU
outputs have an average activity factor of 20%.
Twenty TTL-configured inputs, 20 CMOS-configured
inputs, 32 outputs driving 30 pF loads, and 16 bidirec-
tional I/Os driving 50 pF loads are also generated from
the 40 MHz clock with an av erage activity factor of
20%. The worst-case (VDD = 5.25 V) power dissipation
is estimated as follows:
PPFU = 400 x 3 (0.16 mW/MHz x 20 MHz x 20%)
= 768 mW
Lucent Technologies Inc. 63
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Estimating Power Dissipation (continued)
PCLK = [0.69 mW/MHz + (0.38 mW/MHz – Branch)
(20 Branches)
+ (0.022 mW/MHz – PFU) (150 PFUs)
+ (0.006 mW/MHz – SMEM_PFU)
(16 SMEM_PFUs)] [40 MHz]
= 427 mW
PTTL = 20 x [2.2 mW + (0.17 mW/MHz x 20 MHz
x 20%)]
= 57 mW
PCMOS = 20 x [0.17 mW x 20 MHz x 20%]
= 13 mW
POUT = 30 x [(30 pF + 8.8 pF) x (5.25)2 x 20 MHz
x 20%]
=128 mW
PBID = 16 x [(50 pF + 8.8 pF) x (5.25)2 x 20 MHz
x 20%]
= 104 mW
TOTAL = 1.50 W
OR2TxxA
The total operating power dissipated is estimated by
summing the standby (IDDSB), internal, and external
power dissipated. The internal and external power is
the power consumed in the PLCs and PICs, respec-
tively. In general, the standby power is small and may
be neglected. The total operating power is as follows:
PT = Σ PPLC + Σ PPIC
The internal operating power is made up of two parts:
clock generation and PFU output power. The PFU out-
put power can be estimated based upon the number of
PFU outputs s witching when driving an a verage f an-out
of two:
PPFU = 0.08 mW/MHz
For each PFU output that switches, 0.08 mW/MHz
needs to be multiplied times the frequency (in MHz)
that the output s witches. Generally, this can be esti-
mated by using one-half the clock rate, multiplied by
some activity factor; for example, 20%.
The power dissipated by the clock generation circuitry
is based upon four parts: the fixed clock power, the
power/clock branch row or column, the clock pow er dis-
sipated in each PFU that uses this particular clock, and
the power from the subset of those PFUs that is config-
ured in either of the two synchronous modes (SSPM or
SDPM). Therefore, the clock power can be calculated
for the four parts using the following equations:
OR2T04A Clock Power
P = [0.29 mW/MHz
+ (0.10 mW/MHz – Branch) (# Branches)
+ (0.01 mW/MHz – PFU) (# PFUs)
+ (0.003 mW/MHz – SMEM_PFU)
(# SMEM_PFUs)] fCLK
For a quick estimate, the worst-case (typical circuit)
OR2T04A clock power ≈ 1.8 mW/MHz.
OR2T06A Clock Power
P = [0.30 mW/MHz
+ (0.11 mW/MHz – Branch) (# Branches)
+ (0.01 mW/MHz – PFU) (# PFUs)
+ (0.003 mW/MHz – SMEM_PFU)
(# SMEM_PFUs)] fCLK
For a quick estimate, the worst-case (typical circuit)
OR2T06A clock power ≈ 2.4 mW/MHz.
OR2T08A Clock Power
P = [0.31 mW/MHz
+ (0.12 mW/MHz – Branch) (# Branches)
+ (0.01 mW/MHz – PFU) (# PFUs)
+ (0.003 mW/MHz – SMEM_PFU)
(# SMEM_PFUs)] fCLK
For a quick estimate, the worst-case (typical circuit)
OR2T08A clock power ≈ 3.2 mW/MHz.
OR2T10A Clock Power
P = [0.32 mW/MHz
+ (0.14 mW/MHz – Branch) (# Branches)
+ (0.01 mW/MHz – PFU) (# PFUs)
+ (0.003 mW/MHz – SMEM_PFU)
(# SMEM_PFUs)] fCLK
For a quick estimate, the worst-case (typical circuit)
OR2T10A clock power ≈ 4.0 mW/MHz.
OR2T12A Clock Power
P = [0.33 mW/MHz
+ (0.15 mW/MHz – Branch) (# Branches)
+ (0.01 mW/MHz – PFU) (# PFUs)
+ (0.003 mW/MHz – SMEM_PFU)
(# SMEM_PFUs)] fCLK
For a quick estimate, the worst-case (typical circuit)
OR2T12A clock power ≈ 4.9 mW/MHz.
64 Lucent Technologies Inc.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
Estimating Power Dissipation (continued)
OR2T15A Clock Power
P = [0.34 mW/MHz
+ (0.17 mW/MHz – Branch) (# Branches)
+ (0.01 mW/MHz – PFU) (# PFUs)
+ (0.003 mW/MHz – SMEM_PFU)
(# SMEM_PFUs)] fCLK
For a quick estimate, the worst-case (typical circuit)
OR2T15A clock power ≈ 5.9 mW /MHz.
OR2T26A Clock Power
P = [0.35 mW/MHz
+ (0.19 mW/MHz – Branch) (# Branches)
+ (0.01 mW/MHz – PFU) (# PFUs)
+ (0.003 mW/MHz – SMEM_PFU)
(# SMEM_PFUs)] fCLK
For a quick estimate, the worst-case (typical circuit)
OR2T26A clock power ≈ 8.3 mW /MHz.
OR2T40A Clock Power
P = [0.37 mW/MHz
+ (0.23 mW/MHz – Branch) (# Branches)
+ (0.01 mW/MHz – PFU) (# PFUs)
+ (0.003 mW/MHz – SMEM_PFU)
(# SMEM_PFUs)] fCLK
For a quick estimate, the worst-case (typical circuit)
OR2T40A clock power ≈ 12.4 mW/MHz.
The power dissipated in a PIC is the sum of the power
dissipated in the four I/Os in the PIC. This consists of
power dissipated by inputs and ac power dissipated by
outputs. The power dissipated in each I/O depends on
whether it is configured as an input, output, or input/
output. If an I/O is operating as an output, then there is
a power dissipation component for PIN, as well as
POUT. This is because the output feeds back to the
input.
The power dissipated by an input buffer (VIH = VDD –
0.3 V or higher) is estimated as:
PIN = 0.09 mW/MHz
The 5 V tolerant input buffer feature dissipates addi-
tional dc power. The dc power, PTOL, is always dissi -
pated for the OR2TxxA, regardless of the number of
5 V tolerant input buffers used when the VDD5 pins are
connected t o a 5 V supply as shown in Table 16. This
power is not dissipated when the VDD5 pins are con-
nected to the 3.3 V supply.
Table 16. dc Power for 5 V Tolerant I/Os for
OR2TxxA deviced
The ac power dissipation from an output or bidirec-
tional is estimated by the following:
POUT = (CL + 8.8 pF) x VDD2 x F Watts
where the unit for CL is farads, and the unit for F is Hz.
As an example of estimating power dissipation,
suppose that a fully utilized OR2T15A has an average
of three outputs f or each of the 400 PFUs, that all
20 clock branches are used, that 150 of the 400 PFUs
hav e FFs clock ed at 40 MHz (16 of which are operating
in a synchronous memory mode), and that the PFU
outputs have an average activity factor of 20%.
Twenty inputs, 32 outputs driving 30 pF loads, and
16 bidirectional I/Os driving 50 pF loads are also gen-
erated from the 40 MHz clock with an average activity
factor of 20%. The worst-case (VDD = 3.6 V) power dis-
sipation is estimated as follows:
PPFU = 400 x 3 (0.08 mW/MHz x 20 MHz x 20%)
= 384 mW
PCLK = [0.34 mW/MHz + (0.17 mW/MHz – Branch)
(20 Branches)
+ (0.01 mW/MHz – PFU) (150 PFUs)
+ (0.003 mW/MHz – SMEM_PFU)
(16 SMEM_PFUs)] [40 MHz]
= 212 mW
PIN = 20 x [0.09 mW/MHz x 20 MHz x 20%]
= 7 mW
PTOL = 3.4 mW
POUT = 30 x [(30 pF + 8.8 pF) x (3.6)2 x 20 MHz
x 20%]
= 60 mW
PBID = 16 x [(50 pF + 8.8 pF) x (3.6)2 x 20 MHz
x 20%]
= 49 mW
TOTAL = 0.72 W
Device PTOL (VDD5 = 5.25 V)
2T04A 1.7 mW
2T06A 2.0 mW
2T08A 2.4 mW
2T10A 2.7 mW
2T12A 3.0 mW
2T15A 3.4 mW
2T26A 4.0 mW
2T40A 5.0 mW
Lucent Technologies Inc. 65
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Estimating Power Dissipation (continued)
OR2T15B and OR2T40B
The total operating power dissipated is estimated by
summing the standby (IDDSB), internal, and external
power dissipated. The internal and external power is
the power consumed in the PLCs and PICs, respec-
tively. In general, the standby power is small and may
be neglected. The total operating power is as follows:
PT = Σ PPLC + Σ PPIC
The internal operating power is made up of two parts:
clock generation and PFU output power. The PFU out-
put power can be estimated based upon the number of
PFU outputs s witching when driving an a verage f an-out
of two:
PPFU = 0.08 mW/MHz
For each PFU output that switches, 0.08 mW/MHz
needs to be multiplied times the frequency (in MHz)
that the output s witches. Generally, this can be esti-
mated by using one-half the clock rate, multiplied by
some activity factor; for example, 20%.
The power dissipated by the clock generation circuitry
is based upon four parts: the fixed clock power, the
power/clock branch row or column, the clock pow er dis-
sipated in each PFU that uses this particular clock, and
the power from the subset of those PFUs that is config-
ured in either of the two synchronous modes (SSPM or
SDPM). Therefore, the clock power can be calculated
for the four parts using the following equations:
OR2T15B Clock Power
P = [0.30 mW/MHz
+ (0.85 mW/MHz – Branch) (# Branches)
+ (0.008 mW/MHz – PFU) (# PFUs)
+ (0.002 mW/MHz – SMEM_PFU)
(# SMEM_PFUs)] fCLK
For a quick estimate, the worst-case (typical circuit)
OR2T15B clock power ≈ 3.9 mW /MHz.
OR2T40B Clock Power
P = [0.42 mW/MHz
+ (0.118 mW/MHz – Branch) (# Branches)
+ (0.008 mW/MHz – PFU) (# PFUs)
+ (0.002 mW/MHz – SMEM_PFU)
(# SMEM_PFUs)] fCLK
For a quick estimate, the worst-case (typical circuit)
OR2T40B clock power ≈ 5.5 mW /MHz.
The power dissipated in a PIC is the sum of the power
dissipated in the four I/Os in the PIC. This consists of
power dissipated by inputs and ac power dissipated by
outputs. The power dissipated in each I/O depends on
whether it is configured as an input, output, or input/
output. If an I/O is operating as an output, then there is
a power dissipation component for PIN, as well as
POUT. This is because the output feeds back to the
input.
The power dissipated by an input buffer (VIH = VDD –
0.3 V or higher) is estimated as:
PIN = 0.033 mW/MHz
The OR2TxxB 5 V tolerant input buff er feature does not
dissipate additional dc power.
The ac power dissipation from an output or bidirec-
tional is estimated by the following:
POUT = (CL + 8.8 pF) x VDD2 x F Watts
where the unit for CL is farads, and the unit for F is Hz.
As an example of estimating pow er dissipation,
suppose that a fully utilized OR2T15B has an average
of three outputs for each of the 400 PFUs, that all
20 clock branches are used, that 150 of the 400 PFUs
hav e FFs clocked at 40 MHz (16 of which are operating
in a synchronous memory mode), and that the PFU
outputs have an average activity factor of 20%.
Twenty inputs, 32 outputs driving 30 pF loads, and
16 bidirectional I/Os driving 50 pF loads are also gen-
erated from the 40 MHz cloc k with an average activity
factor of 20%. The worst-case (VDD = 3.6 V) power dis-
sipation is estimated as follows:
PPFU = 400 x 3 (0.08 mW/MHz x 20 MHz x 20%)
= 384 mW
PCLK = [0.30 mW/MHz + (0.085 mW/MHz – Branch)
(20 Branches )
+ (0.008 mW/MHz – PFU) (150 PFUs)
+ (0.002 mW/MHz – SMEM_PFU)
(16 SMEM_PFUs)] [40 MHz]
= 129 mW
PIN = 20 x [0.033 mW/MHz x 20 MHz x 20%]
= 3 mW
PTOL = 3.4 mW
POUT = 30 x [(30 pF + 8.8 pF) x (3.6)2 x 20 MHz
x 20%]
= 60 mW
PBID = 16 x [(50 pF + 8.8 pF) x (3.6)2 x 20 MHz
x 20%]
= 49 mW
TOTAL = 0.72 W
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
66 Lucent Technologies Inc.
Pin Information
Pin Descriptions
This section describes the pins f ound on the Series 2 FPGAs. Any pin not described in this table is a user-program-
mable I/O. During configuration, the user-programmable I/Os are 3-stated with an internal pull-up resistor enabled.
Table 17. Pin Descriptions
Symbol I/O Description
Dedicated Pins
VDD — Positive power supply.
GND — Ground supply.
I/O-VDD5 — 5 V tole rant selec t. (For 2TxxA o nly.) All VDD5 pi ns must be tied to either t he 5 V powe r
supply if 5 V tolerant I/O buffers are to be used, or to the 3.3 V power supply (VDD) if
they are not. For 2CxxA and 2TxxB de vices, these pins are user-programmable I/Os.
RESET I Dur i ng config uration, RE SE T forces t he restart of configuration and a pull-up is
enabled. After con figuration, RESET can be used as a general FPGA input or as a
direct input, which causes all PLC latches/FFs to be asynchronously set/reset.
CCLK I In the master and asynchronous peripheral modes, CCLK is an output which strobes
configuration data in. In the slave or synchronous peripheral mode, CCLK is input syn-
chronous with the data on DI N or D[7 :0].
DONE I/O DONE is a bidirectional pin with an optional pull-up resistor. As an active-high, open-
drain output, a high-l evel on this s i gnal indicates that conf iguration is complete. As a n
input, a low lev el on DONE delays FPGA start-up af ter configu ration*.
PRGM IPRGM is an active-low input that forces the restart of configuration and resets the
boundary-scan circuitry. This pin always has an active pull-up.
RD_CFG I This pin must be held high during device initialization until the INIT pin goes high.
This pin always has an active pullup.
During configuration, RD_CFG is an active-low input that activates the TS_ALL function
and 3- states all o f the I/O.
After configuration, RD_CFG can be selected (via a bit stream option) to activate the
TS_ALL function as described above, or, if readback is enabled via a bit stream option,
a high-to-low transition on RD_CFG will initia te readback of the configuration dat a,
including PFU output states, starting with frame address 0.
RD_D ATA/TDO O RD_DATA/TDO is a dual-function pin. If used for readback, RD_DATA provides configu-
ration data out. If used in boundary scan, TDO is test data out.
Special-Purpos e Pins (Become User I/O After Configuration)
RDY/RCLK O During configuration in peripheral mode, RDY indicates another byte can be written to
the FPGA. If a read operation is done when the device is selected, the same status is
also available on D7 in asynchronous peripheral mode. After configuration, the pin is a
user-programmable I/O*.
During the mast er para llel configur ation mo de RCLK, which is a read o utput s ignal to an
e x ternal m em ory. This outp ut is n ot no rmally us ed. Af t er c onf ig ur a tio n, t h is p in is a use r-
programmable I/O pin*.
DIN I During slave serial or master serial configuration modes, DIN accepts serial configura-
tion da ta synchro nous with CCLK. During parallel configuration modes, DIN is the D0
input. During configuration, a pull-up is enabled, and after configuration, this pin is a
user-programmable I/O pin*.
* The FPGA States of Operation section contains more information on how to control these signals dur ing start-up. The timing of DONE
release is controlled by one set of bit stream options, and the timing of the s imultaneous release of all other configuration pins (and the acti-
v ation of all user I/Os) is controlled by a second set of options.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 67
Special-Purpose Pins Special-Purpose Pins (Be come User I/O After Config uration) (continued)
M0, M1, M2 I During powerup and initialization, M0—M2 are used to select the configuration mode
with their values latched on the rising edge of INIT. See Table 7 for the configuration
modes. During configuration, a pull-up is enabled, and after configuration, the pins are
user-programmable I/O*.
M3 I During powerup and initialization, M 3 is used to select the spe ed of the internal oscilla-
tor during conf iguratio n, with its value latched on the rising edge of INIT. When M3 is
low, the oscillato r frequency is 10 MHz. When M3 is high, the oscillator is 1.25 MHz.
During configuration, a pull-up is enabled, and after configuration, this pin is a user-pro-
grammable I/O pin*.
TDI, TCK, TMS I If boundary scan is used, these pins are Test Data In, Test Cloc k, and Test Mode Select
inputs. If boundary scan is not selected, all boundary-sca n functions are inhibited once
configuration is complete, and these pins are user-programmable I/O pins. Even if
boundary scan is not used, either TCK or TMS must be held at logic 1 during configura-
tion. Eac h pin has a pull-up enab led during configuration*.
HDC O High During Configuration is outpu t high u nt il configuration is complete. It is used as a
control output indicating that configuration is not complete. After configuration, this pin is
a user-programmable I/O pi n*.
LDC O L ow During Confi gura ti on is output lo w until configuration is complete. It is used as a
control output indicating that configuration is not complete. After configuration, this pin is
a user-programmable I/O pi n*.
INIT I/O INIT is a bidirectional signal before and during configuration. During conf iguration, a
pull-up is enabled, but an external pull-up resistor is recomm ended. As an active-low
open-drain output, INIT is held low during power stabilization and internal clearing of
memory. As an a ctiv e-lo w inpu t, INIT holds the FPGA in the wait-state bef ore the start of
configuration. After configuration, the pin is a user-programmable I/O pin*.
CS0, CS1, WR, RD ICS0, CS1, WR, RD are us ed in the asynchronous peripheral configuration mode s. The
FPGA is selected when CS0 is low and CS1 is high. When selected, a low on the write
strobe, WR, loads the data on D[7:0] inputs into an internal data buffer. WR, CS0, and
CS1 are also used as c hip selects in the slav e parallel mode.
A low on RD changes D7 into a status output. As a status indication, a high indicates
ready and a low indicates bus y. WR an d RD should not be used simultaneously. If they
are, the write s trobe overrides. During co nfiguration, a pull -up is enabled, and after con-
figu ration, the pins are user-programmable I/O pins*.
A[17:0] O During master parallel configuration mode, A[17:0] address the configuration EPR OM.
During configuration, a pull-up is enabled, and after configuration, the pins are user-
programmable I/O pi ns*.
D[7:0] I During master parallel, peripheral, and slave parallel configuration modes, D[7:0]
receive configuration data and each pin has a pull-up enabled. After configuration, the
pins are user-programmable I/O pins*.
DOUT O During configuration, DOUT is the serial data output that can drive the DIN of daisy-
chained slave LCA devices. Data out on DOUT changes on the falling edge of CCLK.
After configuration, DOUT is a user-programmable I/O pin*.
Table 17. Pin Descriptions (continued)
Symbol I/O Description
* The FPGA States of Operation section contains more information on how to control these signals dur ing start-up. The timing of DONE
release is controlled by one set of bit stream options, and the timing of the simultaneous release of all other configur ation pins (and the acti-
v ation of all user I/Os) is controlled by a second set of options.
Pin Information (continued)
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
68 Lucent Technologies Inc.
Pin Information (continued)
Package Compatibility
The package pinouts are consistent across
ORCA
Series FPGAs with the f ollowing exception: some user
I/O pins that do not have any special functions will
be converted to VDD5 pins for the OR2TxxA series.
If the designer does not use these pins for the
OR2CxxA and OR2TxxB series, then pinout compati-
bility will be maintained between the
ORCA
OR2CxxA,
OR2TxxA, and OR2TxxB series of FPGAs. Note that
they must be connected to a power supply for the
OR2Txx A series.
Package pinouts being consistent across all
ORCA
Series FPGAs enables a designer to select a package
based on I/O requirements and change the FPGA with-
out laying out the printed-circuit board again. The
change might be to a larger FPGA if additional func-
tionality is needed, or it might be to a smaller FPGA to
decrease unit cost.
Tab le 18A provides the number of user I/Os available
for the
ORCA
OR2CxxA
and OR2TxxB Series FPGAs
f or each av ailable package, and Table 18B provides the
number of user I/Os availab l e in the
ORCA
OR2TxxA
series. It should be noted that the number of user I/Os
available for the OR2TxxA series is reduced from the
equivalent OR2CxxA devices by the number of
required VDD5 pins, as shown in Table 18B. The pins
that are converted from user I/O to VDD5 are denoted
as I/O-VDD5 in the pin information tables (Table 19
through 28). Each package has six dedicated configu-
ration pins.
Tab le 19—Tab le 28. provide the package pin and pin
function for the
ORCA
Series 2 FPGAs and packages.
The bond pad name is identified in the PIC nomencla-
ture used in the
ORCA
Foundry design editor.
When the number of FPGA bond pads exceeds the
number of package pins, bond pads are unused. When
the number of package pins exceeds the number of
bond pads, package pins are left unconnected (no
connects). When a package pin is to be left as a no
connect f or a specific die, it is indicated as a note in the
device pad column f or the FPGA. The tables provide no
inf ormation on unused pads.
* 432 EBGA not available for OR2T15B
Table 18A.
ORCA
OR2CxxA and OR2TxxB Series FPGA I/Os Summary
Device 84-Pin
PLCC 100-Pin
TQFP 144-Pin
TQFP 160-Pin
QFP
208-Pin
SQFP/
SQFP2
240-Pin
SQFP/
SQFP2
256-Pin
PBGA
304-Pin
SQFP/
SQFP2
352-Pin
PBGA 432-Pin
EBGA
OR2C04A
User I/Os 64 77 114 130 160 — — — — —
VDD/VSS 14 17 24 24 31 — — — — —
OR2C06A
User I/Os 64 77 114 130 171 192 192 — — —
VDD/VSS 14 17 24 24 31 42 26 — — —
OR2C08A
User I/Os 64 — — 130 171 192 221 — — —
VDD/VSS 14 — — 24 31 40 26 — — —
OR2C10A
User I/Os 64 — — 130 171 192 221 — 256 —
VDD/VSS 14 — — 24 31 40 26 — 48 —
OR2C12A
User I/Os 64 — — — 171 192 223 252 288 —
VDD/VSS 14———3142264648—
OR2C15A/OR2T15B
User I/Os 64 — — — 171 192 223 252 298 320*
VDD/VSS 14———314226464884
OR2C26A
User I/Os — — — — 171 192 — 252 298 342
VDD/VSS — — — — 31 42 — 46 48 84
OR2C40A/OR2T40B
User I/Os — — — — 171 192 — 252 — 342
VDD/VSS — — — — 31 42 — 46 — 84
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 69
Pin Information (continued)
Table 18B.
ORCA
OR2TxxA Series FPGA I/Os Summary
Device 84-Pin
PLCC 100-Pin
TQFP 144-Pin
TQFP 160-Pin
QFP
208-Pin
SQFP/
SQFP2
240-Pin
SQFP/
SQFP2
256-Pin
PBGA 352-Pin
PBGA 432-Pin
EBGA
OR2T04A
User I/Os 62 74 110 126 152 — — — —
VDD/VSS 14 17 24 24 31 — — — —
VDD523448————
OR2T06A
User I/Os 62 74 110 126 163 184 182 — —
VDD/VSS 14 17 24 24 31 42 26 — —
VDD523448810——
OR2T08A
User I/Os 62 — — 126 163 184 209 — —
VDD/VSS 14 — — 24 31 40 26 — —
VDD52——48812——
OR2T10A
User I/Os 62 — — 126 163 184 209 244 —
VDD/VSS 14 — — 24 31 40 26 48 —
VDD52——4881212—
OR2T12A
User I/Os 62 — — — 163 184 211 276 —
VDD/VSS 14 — — — 31 42 26 48 —
VDD52———881212—
OR2T15A
User I/Os 62 — — — 163 184 2 11 286 307
VDD/VSS 14 — — — 31 42 26 48 84
VDD52———88121212
OR2T26A
User I/Os — — — — 163 184 — 286 326
VDD/VSS — — — — 31 42 — 48 84
VDD5 — — — — 8 8 — 12 16
OR2T40A
User I/Os — — — — 163 184 — 286 326
VDD/VSS — — — — 31 42 — 48 84
VDD5 — — — — 8 8 — 12 16
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
70 Lucent Technologies Inc.
Pin Information (continued)
Compatibility with Series 3 FPGAs
Pinouts for the OR2CxxA, OR2TxxA, and OR2TxxB devices will be consistent with the Series 3 FPGAs for all
devices offered in the same packages. This includes the following pins: VDD, VSS, VDD5 (OR3C/Txxx series only),
and all configuration pins. Identical to the OR2TxxB devices, Series 3 devices provide 5 V tolerant I/Os without a
dedicated VDD5 supply
The following restrictions apply:
1. There are two configuration modes supported in the OR2C/TxxA series that are not supported in the
Series 3 FPGAs series: master parallel down and synchronous peripheral modes. The Series 3 FPGAs hav e two
new microprocessor interface (MPI) configuration modes that are unavailable in the Series 2.
2. There are 4 pins—one per each device side—that are user I/O in the OR2C/TxxA series which can only be used
as fast dedicated clocks or global inputs in the Series 3 series. These pins are also used to drive the Express-
CLK to the I/O FFs on their given side of the device. These four middle ExpressCLK pins should not be used to
connect to a programmable clock manager (PCM). A corner ExpressCLK input should be used instead (see note
below). See Table 18C for a list of these pins in each package.
3. There are two other pins that are user I/O in both the Series 2 and Series 3 series but also have optional added
functionality in the Series 3 series. Each of these pins drives the ExpressCLKs on two sides of the device. They
also have fast connectivity to the programmable clock manager (PCM). See Table 18C for a preliminary list of
these pins in each package.
Note: The ECK R, ECKL, ECKT, and ECKB pins drive the ExpressCLK on their given edge of the device, while I/O—SECKLL and
I/O—SECKUR drive an ExpressCLK on two edges of the device and provide connectivity to the programm able clock manager.
Table 18C. Series 3 ExpressCLK Pins
Pin Name/
Package 208-Pin
SQFP2 240-Pin
SQFP2 256-Pin
PBGA 352-Pin
PBGA 432-Pin
EBGA 600-Pin
EBGA
ECKL 22 26 K3 N2 R29 U33
ECKB 80 91 W11 AE14 AH16 AM18
ECKR 131 152 K18 N23 T2 V2
ECKT 178 207 B11 B14 C15 C17
I/O—SECKLL 49 56 W1 AB4 AG29 AK34
I/O—SECKUR 159 184 A19 A25 D5 D5
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 71
Pin Information (continued)
Table 19. OR2C/2T04A, OR2C/2T06A, OR2C/2T08A, OR2C/2T10A, OR2C/2T12A, and OR2C/2T15A
84-Pin PLCC Pinout
Pin 2C/2T04A
Pad 2C/2T06A
Pad 2C/2T08A
Pad 2C/2T10A
Pad 2C/2T12A
Pad 2C/2T15A
Pad Function
1V
SS VSS VSS VSS VSS VSS VSS
2 PT5A PT6A PT7A PT8A PT9A PT10A I/O-D2
3V
SS VSS VSS VSS VSS VSS VSS
4 PT4D PT5D PT6D PT7D PT8D PT9D I/O-D1
5 PT4A PT5A PT6A PT7A PT8A PT9A I/O-D0/DIN
6 PT3A PT4A PT5A PT6A PT7A PT8A I/O-DOUT
7 PT2D PT3D PT4D PT5D PT6D PT7D I/O-VDD5
8 PT2A PT3A PT4A PT4A PT5A PT6A I/O-TDI
9 PT1D PT2A PT3A PT3A PT3A PT4A I/O-TMS
10 PT1A PT1A PT1A PT1A PT1A PT1A I/O-TCK
11 RD_DATA/TDO RD_DATA/TDO RD_DATA/TDO RD_DATA/TDO RD_DATA/TDO RD_DATA/TDO RD_DATA/TDO
12 VDD VDD VDD VDD VDD VDD VDD
13 VSS VSS VSS VSS VSS VSS VSS
14 PL1C PL1A PL2D PL2D PL2D PL2D I/O-A0
15 PL1A PL2A PL3A PL3A PL4A PL5A I/O-A1
16 PL2D PL3D PL4D PL4A PL5A PL6A I/O-A2
17 PL2A PL3A PL4A PL5A PL6A PL7A I/O-A3
18 PL3A PL4A PL5A PL6A PL7A PL8A I/O-A4
19 PL4D PL5D PL6D PL7D PL8D PL9D I/O-A5
20 PL4A PL5A PL6A PL7A PL8A PL9A I/O-A6
21 PL5A PL6A PL7A PL8A PL9A PL10A I/O-A7
22 VDD VDD VDD VDD VDD VDD VDD
23 PL6A PL7A PL8A PL9A PL10A PL11A I/O-A8
24 VSS VSS VSS VSS VSS VSS VSS
25 PL7D PL8D PL9D PL10D PL11D PL12D I/O-A9
26 PL7A PL8A PL9A PL10A PL11A PL12A I/O-A10
27 PL8A PL9A PL10A PL11A PL12A PL13A I/O-A11
28 PL9D PL10D PL11D PL12D PL13D PL14D I/O-A12
29 PL9A PL10A PL11A PL13D PL14B PL15B I/O-A13
30 PL10D PL11A PL12A PL14C PL16D PL17D I/O-A14
31 PL10A PL12A PL14A PL16A PL18A PL20A I/O-A15
32 CCLK CCLK CCLK CCLK CCLK CCLK CCLK
33 VDD VDD VDD VDD VDD VDD VDD
34 VSS VSS VSS VSS VSS VSS VSS
35 PB1A PB1A PB1A PB1A PB1A PB1A I/O-A16
36 PB1D PB2A PB3A PB3B PB3D PB4D I/O-A17
37 PB2A PB3A PB3D PB4D PB5B PB6B I/O
38 PB2D PB3D PB4D PB5D PB6D PB7D I/O
39 PB3A PB4A PB5A PB6A PB7A PB8A I/O
40 PB4A PB5A PB6A PB7A PB8A PB9A I/O
41 PB4D PB5D PB6D PB7D PB8D PB9D I/O
42 PB5A PB6A PB7A PB8A PB9A PB10A I/O
Note: The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, but they are connected to VDD5 for the OR2TxxA
series.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
72 Lucent Technologies Inc.
43 VSS VSS VSS VSS VSS VSS VSS
44 PB6A PB7A PB8A PB9A PB10A PB11A I/O
45 VSS VSS VSS VSS VSS VSS VSS
46 PB7A PB8A PB9A PB10A PB11A PB12A I/O-VDD5
47 PB7D PB8D PB9D PB10D PB11D PB12D I/O
48 PB8A PB9A PB10A PB11A PB12A PB13A I/O-HDC
49 PB9A PB10A PB11A PB12A PB13A PB14A I/O-LDC
50 PB9D PB10D PB11D PB13A PB13D PB14D I/O
51 PB10A PB11A PB12C PB13D PB15A PB16A I/O-INIT
52 PB10D PB12A PB13D PB15D PB18D PB20D I/O
53 DONE DONE DONE DONE DONE DONE DONE
54 RESET RESET RESET RESET RESET RESET RESET
55 PRGM PRGM PRGM PRGM PRGM PRGM PRGM
56 PR10A PR12A PR14A PR16A PR18A PR20A I/O-M0
57 PR10D PR11A PR12A PR14A PR16A PR17A I/O
58 PR9A PR10A PR11A PR13B PR15D PR16D I/O-M1
59 PR9D PR10D PR11D PR12B PR13A PR14A I/O
60 PR8A PR9A PR10A PR11A PR12A PR13A I/O-M2
61 PR7A PR8A PR9A PR10A PR11A PR12A I/O-M3
62 PR7D PR8D PR9D PR10D PR11D PR12D I/O
63 PR6A PR7A PR8D PR9D PR10A PR11A I/O
64 VDD VDD VDD VDD VDD VDD VDD
65 PR5A PR6A PR7A PR8A PR9A PR10A I/O
66 VSS VSS VSS VSS VSS VSS VSS
67 PR4A PR5A PR6A PR7A PR8A PR9A I/O
68 PR4D PR5D PR6D PR7D PR8D PR9D I/O
69 PR3A PR4A PR5A PR6A PR7A PR8A I/O-CS1
70 PR2A PR3A PR4A PR5A PR6A PR7A I/O-CS0
71 PR2D PR3D PR4D PR4D PR5D PR6D I/O
72 PR1A PR2A PR3A PR3A PR4A PR5A I/O-RD
73 PR1D PR1A PR2A PR2A PR2A PR3A I/O-WR
74 RD_CFG RD_CFG RD_CFG RD_CFG RD_CFG RD_CFG RD_CFG
75 VDD VDD VDD VDD VDD VDD VDD
76 VSS VSS VSS VSS VSS VSS VSS
77 PT10C PT12A PT13D PT15D PT17D PT19A I/O-RDY/RCLK
78 PT9D PT11A PT12C PT13D PT15D PT16D I/O-D7
79 PT9C PT10D PT11D PT13A PT14D PT15D I/O
80 PT9A PT10A PT11B PT12B PT13B PT14B I/O-D6
81 PT8A PT9A PT10A PT11A PT12A PT13A I/O-D5
82 PT7D PT8D PT9D PT10D PT11D PT12D I/O
83 PT7A PT8A PT9A PT10A PT11A PT12A I/O-D4
84 PT6A PT7A PT8A PT9A PT10A PT11A I/O-D3
Pin Information (continued)
Table 19. OR2C/2T04A, OR2C/2T06A, OR2C/2T08A, OR2C/2T10A, OR2C/2T12A, and OR2C/2T15A
84-Pin PLCC Pinout (continued)
Pin 2C/2T04A
Pad 2C/2T06A
Pad 2C/2T08A
Pad 2C/2T10A
Pad 2C/2T12A
Pad 2C/2T15A
Pad Function
Note: The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, b ut the y are connected to VDD5 for the OR2TxxA
series.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 73
Pin Information (continued)
Table 20. OR2C/2T04A and OR2C/2T06A 100-Pin TQFP Pinout
Pin 2C/2T04A
Pad 2C/2T06A
Pad Function Pin 2C/2T04A
Pad 2C/2T06A
Pad Function
1V
DD VDD VDD 43 PB8C PB9C I/O
2V
SS VSS VSS 44 PB8D PB9D I/O
3 PL1C PL1A I/O-A0 45 PB9A PB10A I/O-LDC
4 PL1A PL2A I/O-A1 46 PB9D PB10D I/O
5 PL2D PL3D I/O-A2 47 PB10A PB11A I/O-INIT
6 PL2A PL3A I/O-A3 48 PB10D PB12A I/O
7 PL3D PL4D I/O 49 DONE DONE DONE
8 PL3A PL4A I/O-A4 50 VDD VDD VDD
9 PL4D PL5D I/O-A5 51 RESET RESET RESET
10 PL4A PL5A I/O-A6 52 PRGM PRGM PRGM
11 PL5D PL6D I/O 53 PR10A PR12A I/O-M0
12 PL5A PL6A I/O-A7 54 PR10D PR11A I/O
13 VDD VDD VDD 55 PR9A PR10A I/O-M1
14 PL6A PL7A I/O-A8 56 PR9D PR10D I/O
15 VSS VSS VSS 57 PR8A PR9A I/O-M2
16 PL7D PL8D I/O-A9 58 PR8D PR9D I/O
17 PL7A PL8A I/O-A10 59 PR7A PR8A I/O-M3
18 PL8A PL9A I/O-A11 60 PR7D PR8D I/O
19 PL9D PL10D I/O-A12 61 VSS VSS VSS
20 PL9C PL10C I/O 62 PR6A PR7A I/O
21 PL9A PL10A I/O-A13 63 VDD VDD VDD
22 PL10D PL11A I/O-A14 64 PR5A PR6A I/O
23 PL10A PL12A I/O-A15 65 VSS VSS VSS
24 VSS VSS VSS 66 PR4A PR5A I/O-VDD5
25 CCLK CCLK CCLK 67 PR4D PR5D I/O
26 VDD VDD VDD 68 PR3A PR4A I/O-CS1
27 VSS VSS VSS 69 PR3D PR4D I/O
28 PB1A PB1A I/O-A16 70 PR2A PR3A I/O-CS0
29 PB1C PB1D I/O 71 PR2D PR3D I/O
30 PB1D PB2A I/O-A17 72 PR1A PR2A I/O-RD
31 PB2A PB3A I/O 73 PR1C PR2D I/O
32 PB2D PB3D I/O 74 PR1D PR1A I/O-WR
33 PB3A PB4A I/O 75 RD_CFG RD_CFG RD_CFG
34 PB4A PB5A I/O 76 VDD VDD VDD
35 PB4D PB5D I/O 77 VSS VSS VSS
36 PB5A PB6A I/O 78 PT10C PT12A I/O-RDY/RCLK
37 VSS VSS VSS 79 PT9D PT11A I/O-D7
38 PB6A PB7A I/O 80 PT9C PT10D I/O
39 VSS VSS VSS 81 PT9A PT10A I/O-D6
40 PB7A PB8A I/O-VDD582PT8D PT9D I/O
41 PB7D PB8D I/O 83 PT8A PT9A I/O-D5
42 PB8A PB9A I/O-HDC 84 PT7D PT8D I/O
Note: The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, but they are connected to VDD5 for the OR2TxxA
series.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
74 Lucent Technologies Inc.
Pin 2C/2T04A
Pad 2C/2T06A
Pad Function Pin 2C/2T04A
Pad 2C/2T06A
Pad Function
85 PT7A PT8A I/O-D4 93 PT3D PT4D I/O
86 PT6D PT7D I/O 94 PT3A PT4A I/O-DOUT
87 PT6A PT7A I/O-D3 95 PT2D PT3D I/O-VDD5
88 VSS VSS VSS 96 PT2A PT3A I/O-TDI
89 PT5A PT6A I/O-D2 97 PT1D PT2A I/O-TMS
90 VSS VSS VSS 98 PT1C PT1D I/O
91 PT4D PT5D I/O-D1 99 PT1A PT1A I/O-TCK
92 PT4A PT5A I/O-D0/DIN 100 RD_DATA/
TDO RD_DATA/TDO RD_DATA/TDO
Note: The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, b ut the y are connected to VDD5 for the OR2TxxA
series.
Pin Information (continued)
Table 20. OR2C/2T04A and OR2C/2T06A 100-Pin TQFP Pinout (continued)
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 75
Pin Information (continued)
Table 21. OR2C/2T04A and OR2C/2T06A 144-Pin TQFP Pinout
Pin 2C/2T04A
Pad 2C/2T06A
Pad Function Pin 2C/2T04A
Pad 2C/2T06A
Pad Function
1V
DD VDD VDD 43 PB2B PB3B I/O
2V
SS VSS VSS 44 PB2D PB3D I/O
3PL1C PL1A I/O-A0 45V
DD VDD VDD
4 PL1B PL2D I/O 46 PB3A PB4A I/O
5 PL1A PL2A I/O-A1 47 PB3D PB4D I/O
6 PL2D PL3D I/O-A2 48 PB4A PB5A I/O
7 PL2A PL3A I/O-A3 49 PB4C PB5C I/O
8 PL3D PL4D I/O 50 PB4D PB5D I/O
9 PL3C PL4C I/O 51 PB5A PB6A I/O
10 PL3A PL4A I/O-A4 52 PB5C PB6C I/O
11 PL4D PL5D I/O-A5 53 PB5D PB6D I/O
12 PL4C PL5C I/O 54 VSS VSS VSS
13 PL4A PL5A I/O-A6 55 PB6A PB7A I/O
14 VSS VSS VSS 56 PB6C PB7C I/O
15 PL5D PL6D I/O 57 PB6D PB7D I/O
16 PL5C PL6C I/O 58 PB7A PB8A I/O-VDD5
17 PL5A PL6A I/O-A7 59 PB7D PB8D I/O
18 VDD VDD VDD 60 PB8A PB9A I/O-HDC
19 PL6D PL7D I/O 61 PB8C PB9C I/O
20 PL6C PL7C I/O-VDD5 62 PB8D PB9D I/O
21 PL6A PL7A I/O-A8 63 VDD VDD VDD
22 VSS VSS VSS 64 PB9A PB10A I/O-LDC
23 PL7D PL8D I/O-A9 65 PB9C PB10C I/O
24 PL7A PL8A I/O-A10 66 PB9D PB10D I/O
25 PL8D PL9D I/O 67 PB10A PB11A I/O-INIT
26 PL8C PL9C I/O 68 PB10C PB11D I/O
27 PL8A PL9A I/O-A11 69 PB10D PB12A I/O
28 PL9D PL10D I/O-A12 70 VSS VSS VSS
29 PL9C PL10C I/O 71 DONE DONE DONE
30 PL9A PL10A I/O-A13 72 VDD VDD VDD
31 PL10D PL11A I/O-A14 73 VSS VSS VSS
32 PL10C PL12D I/O 74 RESET RESET RESET
33 PL10B PL12B I/O 75 PRGM PRGM PRGM
34 PL10A PL12A I/O-A15 76 PR10A PR12A I/O-M0
35 VSS VSS VSS 77 PR10B PR12D I/O
36 CCLK CCLK CCLK 78 PR10D PR11A I/O
37 VDD VDD VDD 79 PR9A PR10A I/O-M1
38 VSS VSS VSS 80 PR9C PR10C I/O
39 PB1A PB1A I/O-A16 81 PR9D PR10D I/O
40 PB1C PB1D I/O 82 PR8A PR9A I/O-M2
41 PB1D PB2A I/O-A17 83 PR8B PR9B I/O
42 PB2A PB3A I/O 84 PR8D PR9D I/O
Note: The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, but they are connected to VDD5 for the OR2TxxA
series.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
76 Lucent Technologies Inc.
Pin 2C/2T04A
Pad 2C/2 T06A
Pad Function Pin 2C/2T04A
Pad 2C/2T06A
Pad Function
85 PR7A PR8A I/O-M3 115 PT9C PT10D I/O
86 PR7D PR8D I/O 116 PT9B PT10C I/O
87 VSS VSS VSS 117 PT9A PT10A I/O-D6
88 PR6A PR7A I/O 118 VDD VDD VDD
89 PR6C PR7C I/O 119 PT8D PT9D I/O
90 PR6D PR7D I/O 120 PT8A PT9A I/O-D5
91 VDD VDD VDD 121 PT7D PT8D I/O
92 PR5A PR6A I/O 122 PT7B PT8B I/O
93 PR5C PR6C I/O 123 PT7A PT8A I/O-D4
94 PR5D PR6D I/O 124 PT6D PT7D I/O
95 VSS VSS VSS 125 PT6C PT7C I/O
96 PR4A PR5A I/O-VDD5 126 PT6A PT7A I/O-D3
97 PR4C PR5C I/O 127 VSS VSS VSS
98 PR4D PR5D I/O 128 PT5D PT6D I/O
99 PR3A PR4A I/O-CS1 129 PT5C PT6C I/O
100 PR3D PR4D I/O 130 PT5A PT6A I/O-D2
101 PR2A PR3A I/O-CS0 131 PT4D PT5D I/O-D1
102 PR2D PR3D I/O 132 PT4C PT5C I/O
103 PR1A PR2A I/O-RD 133 PT4A PT5A I/O-D0/DIN
104 PR1B PR2C I/O 134 PT3D PT4D I/O
105 PR1C PR2D I/O 135 PT3A PT4A I/O-DOUT
106 PR1D PR1A I/O-WR 136 VDD VDD VDD
107 VSS VSS VSS 137 PT2D PT3D I/O-VDD5
108 RD_CFG RD_CFG RD_CFG 138 PT2C PT3C I/O
109 VDD VDD VDD 139 PT2A PT3A I/O-TDI
110 VSS VSS VSS 140 PT1D PT2A I/O-TMS
111 PT10D PT12D I/O 141 PT1C PT1D I/O
112 PT10C PT12A I/O-RDY/RCLK 142 PT1A PT1A I/O-TCK
113 PT10B PT11D I/O 143 VSS VSS VSS
114 PT9D PT11A I/O-D7 144 RD_DATA/
TDO RD_DATA/
TDO RD_DATA/TDO
Pin Information (continued)
Table 21. OR2C/2T04A and OR2C/2T06A 144-Pin TQFP Pinout (continued)
Note: The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, b ut the y are connected to VDD5 for the OR2TxxA
series.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 77
Pin Information (continued)
Table 22. OR2C/2T04A, OR2C/2T06A, OR2C/2T08A, and OR2C/2T10A 160-Pin QFP Pinout
Pin 2C/2T04A Pad 2C/2T06A Pad 2C/2T08A Pad 2C/2T10A Pad Function
1V
DD VDD VDD VDD VDD
2V
SS VSS VSS VSS VSS
3 PL1D PL1D PL1D PL1D I/O
4 PL1C PL1A PL2D PL2D I/O-A0
5 PL1B PL2D PL3D PL3D I/O
6 PL1A PL2A PL3A PL3A I/O-A1
7 PL2D PL3D PL4D PL4A I/O-A2
8 PL2C PL3C PL4C PL5C I/O
9 PL2A PL3A PL4A PL5A I/O-A3
10 PL3D PL4D PL5D PL6D I/O
11 PL3C PL4C PL5C PL6C I/O
12 PL3A PL4A PL5A PL6A I/O-A4
13 PL4D PL5D PL6D PL7D I/O-A5
14 PL4C PL5C PL6C PL7C I/O
15 PL4A PL5A PL6A PL7A I/O-A6
16 VSS VSS VSS VSS VSS
17 PL5D PL6D PL7D PL8D I/O
18 PL5C PL6C PL7C PL8C I/O
19 PL5A PL6A PL7A PL8A I/O-A7
20 VDD VDD VDD VDD VDD
21 PL6D PL7D PL8D PL9D I/O
22 PL6C PL7C PL8C PL9C I/O-VDD5
23 PL6A PL7A PL8A PL9A I/O-A8
24 VSS VSS VSS VSS VSS
25 PL7D PL8D PL9D PL10D I/O-A9
26 PL7B PL8B PL9B PL10B I/O
27 PL7A PL8A PL9A PL10A I/O-A10
28 PL8D PL9D PL10D PL11D I/O
29 PL8C PL9C PL10C PL11C I/O
30 PL8A PL9A PL10A PL11A I/O-A11
31 PL9D PL10D PL11D PL12D I/O-A12
32 PL9C PL10C PL11C PL12C I/O
33 PL9B PL10B PL11B PL12B I/O
34 PL9A PL10A PL11A PL13D I/O-A13
35 PL10D PL11A PL12A PL14C I/O-A14
36 PL10C PL12D PL13D PL15D I/O
37 PL10B PL12B PL14D PL16D I/O
38 PL10A PL12A PL14A PL16A I/O-A15
39 CCLK CCLK CCLK CCLK CCLK
40 VSS VSS VSS VSS VSS
Note: The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, but they are connected to VDD5 for the OR2TxxA
series.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
78 Lucent Technologies Inc.
41 VDD VDD VDD VDD VDD
42 VSS VSS VSS VSS VSS
43 PB1A PB1A PB1A PB1A I/O-A16
44 PB1B PB1C PB2A PB2A I/O
45 PB1C PB1D PB2D PB2D I/O
46 PB1D PB2A PB3A PB3B I/O-A17
47 PB2A PB3A PB3D PB4D I/O
48 PB2B PB3B PB4A PB5A I/O
49 PB2C PB3C PB4C PB5C I/O
50 PB2D PB3D PB4D PB5D I/O
51 VDD VDD VDD VDD VDD
52 PB3A PB4A PB5A PB6A I/O
53 PB3D PB4D PB5D PB6D I/O
54 PB4A PB5A PB6A PB7A I/O
55 PB4C PB5C PB6C PB7C I/O
56 PB4D PB5D PB6D PB7D I/O
57 PB5A PB6A PB7A PB8A I/O
58 PB5C PB6C PB7C PB8C I/O
59 PB5D PB6D PB7D PB8D I/O
60 VSS VSS VSS VSS VSS
61 PB6A PB7A PB8A PB9A I/O
62 PB6C PB7C PB8C PB9C I/O
63 PB6D PB7D PB8D PB9D I/O
64 PB7A PB8A PB9A PB10A I/O-VDD5
65 PB7D PB8D PB9D PB10D I/O
66 PB8A PB9A PB10A PB11A I/O-HDC
67 PB8C PB9C PB10C PB11C I/O
68 PB8D PB9D PB10D PB11D I/O
69 VDD VDD VDD VDD VDD
70 PB9A PB10A PB11A PB12A I/O-LDC
71 PB9B PB10B PB11D PB13A I/O
72 PB9C PB10C PB12A PB13B I/O
73 PB9D PB10D PB12B PB13C I/O
74 PB10A PB11A PB12C PB13D I/O-INIT
75 PB10B PB11C PB12D PB14A I/O
76 PB10C PB11D PB13D PB15D I/O
77 PB10D PB12A PB14D PB16D I/O
78 VSS VSS VSS VSS VSS
79 DONE DONE DONE DONE DONE
80 VDD VDD VDD VDD VDD
81 VSS VSS VSS VSS VSS
Pin Information (continued)
Table 22. OR2C/2T04A, OR2C/2T06A, OR2C/2T08A, and OR2C/2T10A 160-Pin QFP Pinout (continued)
Pin 2C/2T04A Pad 2C/2T06A Pad 2C/2T08A Pad 2C/2T10A P ad Function
Note: The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, b ut the y are connected to VDD5 for the OR2TxxA
series.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 79
82 RESET RESET RESET RESET RESET
83 PRGM PRGM PRGM PRGM PRGM
84 PR10A PR12A PR14A PR16A I/O-M0
85 PR10B PR12D PR13A PR15A I/O
86 PR10C PR11A PR13D PR15D I/O
87 PR10D PR11B PR12A PR14A I/O
88 PR9A PR10A PR11A PR13B I/O-M1
89 PR9B PR10B PR11B PR13C I/O
90 PR9C PR10C PR11C PR12A I/O
91 PR9D PR10D PR11D PR12B I/O
92 PR8A PR9A PR10A PR11A I/O-M2
93 PR8B PR9B PR10B PR11B I/O
94 PR8D PR9D PR10D PR11D I/O
95 PR7A PR8A PR9A PR10A I/O-M3
96 PR7D PR8D PR9D PR10D I/O
97 VSS VSS VSS VSS VSS
98 PR6A PR7A PR8A PR9A I/O
99 PR6C PR7C PR8C PR9C I/O
100 PR6D PR7D PR8D PR9D I/O
101 VDD VDD VDD VDD VDD
102 PR5A PR6A PR7A PR8A I/O
103 PR5C PR6C PR7C PR8C I/O
104 PR5D PR6D PR7D PR8D I/O
105 VSS VSS VSS VSS VSS
106 PR4A PR5A PR6A PR7A I/O-VDD5
107 PR4C PR5C PR6C PR7C I/O
108 PR4D PR5D PR6D PR7D I/O
109 PR3A PR4A PR5A PR6A I/O-CS1
110 PR3B PR4B PR5B PR6B I/O
111 PR3D PR4D PR5D PR6D I/O
112 PR2A PR3A PR4A PR5A I/O-CS0
113 PR2C PR3C PR4B PR4B I/O
114 PR2D PR3D PR4D PR4D I/O
115 PR1A PR2A PR3A PR3A I/O-RD
116 PR1B PR2C PR3C PR3C I/O
117 PR1C PR2D PR3D PR3D I/O
118 PR1D PR1A PR2A PR2A I/O-WR
119 VSS VSS VSS VSS VSS
120 RD_CFG RD_CFG RD_CFG RD_CFG RD_CFG
121 VDD VDD VDD VDD VDD
122 VSS VSS VSS VSS VSS
Pin Information (continued)
Table 22. OR2C/2T04A, OR2C/2T06A, OR2C/2T08A, and OR2C/2T10A 160-Pin QFP Pinout (continued)
Pin 2C/2T04A Pad 2C/2T06A Pad 2C/2T08A Pad 2C/2T10A Pad Function
Note: The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, but they are connected to VDD5 for the OR2TxxA
series.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
80 Lucent Technologies Inc.
123 PT10D PT12D PT14D PT16D I/O
124 PT10C PT12A PT13D PT15D I/O-RDY/RCLK
125 PT10B PT11D PT13A PT15A I/O
126 PT10A PT11C PT12D PT14D I/O
127 PT9D PT11A PT12C PT13D I/O-D7
128 PT9C PT10D PT12A PT13B I/O
129 PT9B PT10C PT11D PT13A I/O
130 PT9A PT10A PT11B PT12B I/O-D6
131 VDD VDD VDD VDD VDD
132 PT8D PT9D PT10D PT11D I/O
133 PT8A PT9A PT10A PT11A I/O-D5
134 PT7D PT8D PT9D PT10D I/O
135 PT7B PT8B PT9B PT10B I/O
136 PT7A PT8A PT9A PT10A I/O-D4
137 PT6D PT7D PT8D PT9D I/O
138 PT6C PT7C PT8C PT9C I/O
139 PT6A PT7A PT8A PT9A I/O-D3
140 VSS VSS VSS VSS VSS
141 PT5D PT6D PT7D PT8D I/O
142 PT5C PT6C PT7C PT8C I/O
143 PT5A PT6A PT7A PT8A I/O-D2
144 PT4D PT5D PT6D PT7D I/O-D1
145 PT4C PT5C PT6C PT7C I/O
146 PT4A PT5A PT6A PT7A I/O-D0/DIN
147 PT3D PT4D PT5D PT6D I/O
148 PT3C PT4C PT5C PT6C I/O
149 PT3A PT4A PT5A PT6A I/O-DOUT
150 VDD VDD VDD VDD VDD
151 PT2D PT3D PT4D PT5D I/O-VDD5
152 PT2C PT3C PT4C PT5A I/O
153 PT2B PT3B PT4B PT4D I/O
154 PT2A PT3A PT4A PT4A I/O-TDI
155 PT1D PT2A PT3A PT3A I/O-TMS
156 PT1C PT1D PT2A PT2A I/O
157 PT1B PT1C PT1D PT1D I/O
158 PT1A PT1A PT1A PT1A I/O-TCK
159 VSS VSS VSS VSS VSS
160 RD_DATA/TDO RD_DATA/TDO RD_DATA/TDO RD_DATA/TDO RD_DATA/TDO
Pin Information (continued)
Table 22. OR2C/2T04A, OR2C/2T06A, OR2C/2T08A, and OR2C/2T10A 160-Pin QFP Pinout (continued)
Pin 2C/2T04A Pad 2C/2T06A Pad 2C/2T08A Pad 2C/2T10A P ad Function
Note: The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, b ut the y are connected to VDD5 for the OR2TxxA
series.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 81
Pin Information (continued)
Table 23. OR2C/2T04A, OR2C/2T06A, OR2C/2T08A, OR2C/2T10A, OR2C/2T12A, OR2C/2T15A/B,
OR2C/2T26A, and OR2C/2T40A/B 208-Pin SQFP/SQFP2 Pinout
Pin 2C/2T04A
Pad 2C/2T06A
Pad 2C/2T08A
Pad 2C/2T10A
Pad 2C/2T12A
Pad 2C/2T15A/B
Pad 2C/2T26A
Pad 2C/2T40A/B
Pad Function
1 VSS VSS VSS VSS VSS VSS VSS VSS VSS
2 VSS VSS VSS VSS VSS VSS VSS VSS VSS
3 PL1D PL1D PL1D PL1D PL1D PL1D PL1D PL1D I/O
4 PL1C PL1A PL2D PL2D PL2D PL2D PL2D PL3D I/O-A0
5 PL1B PL2D PL3D PL3D PL3D PL4D PL4D PL5D I/O-VDD5
6 See Note PL2C PL3C PL 3C PL3A PL 4A PL4A PL6D I/O
7 PL1A PL2A PL3A PL3A PL4A PL5A PL5A PL8D I/O-A1
8 PL2D PL3D PL4D PL4A PL5A PL6A PL6A PL9A I/O-A2
9 PL2C PL3C PL4C PL5C PL6D PL7D PL7D PL10D I/O
10 PL2B PL3B PL4B PL5B PL6B PL7B PL7B PL10B I/O
11 PL2A PL3A PL4A PL5A PL6A PL7A PL7A PL10A I/O-A3
12 VDD VDD VDD VDD VDD VDD VDD VDD VDD
13 PL3D PL4D PL5D PL6D PL7D PL8D PL8D PL11D I/O
14 PL3C PL4C PL5C PL6C PL7C PL8C PL8A PL11A I/O
15 PL3B PL4B PL5B PL6B PL7B PL8B PL9D PL12D I/O
16 PL3A PL4A PL5A PL6A PL7A PL8A PL9A PL12A I/O-A4
17 PL4D PL5D PL6D PL7D PL8D PL9D PL10D PL13D I/O-A5
18 PL4C PL5C PL6C PL7C PL8C PL9C PL10A PL13A I/O
19 PL4B PL5B PL6B PL7B PL8B PL9B PL11D PL14D I/O
20 PL4A PL5A PL6A PL7A PL8A PL9A PL11A PL14A I/O-A6
21 VSS VSS VSS VSS VSS VSS VSS VSS VSS
22 PL5D PL6D PL7D PL8D PL9D PL10D PL12D PL15D I/O
23 PL5C PL6C PL7C PL8C PL9C PL10C PL12C PL15C I/O
24 PL5B PL6B PL7B PL8B PL9B PL10B PL12B PL15B I/O
25 PL5A PL6A PL7A PL8A PL9A PL10A PL12A PL15A I/O-A7
26 VDD VDD VDD VDD VDD VDD VDD VDD VDD
27 PL6D PL7D PL8D PL9D PL10D PL11D PL13D PL16D I/O
28 PL6C PL7C PL8C PL9C PL10C PL11C PL13C PL16C I/O-VDD5
29 PL6B PL7B PL8B PL9B PL10B PL11B PL13B PL16B I/O
30 PL6A PL7A PL8A PL9A PL10A PL11A PL13A PL16A I/O-A8
31 VSS VSS VSS VSS VSS VSS VSS VSS VSS
32 PL7D PL8D PL9D PL10D PL11D PL12D PL14D PL17D I/O-A9
33 PL7C PL8C PL9C PL10C PL11C PL12C PL14A PL17A I/O
34 PL7B PL8B PL9B PL10B PL11B PL12B PL15D PL18D I/O
35 PL7A PL8A PL9A PL10A PL11A PL12A PL15A PL18A I/O-A10
36 PL8D PL9D PL10D PL11D PL12D PL13D PL16D PL19D I/O
37 PL8C PL9C PL10C PL11C PL12C PL13C PL16A PL19A I/O
38 PL8B PL9B PL10B PL11B PL12B PL13B PL17D PL20D I/O
39 PL8A PL9A PL10A PL11A PL12A PL13A PL17A PL20A I/O-A11
40 VDD VDD VDD VDD VDD VDD VDD VDD VDD
41 PL9D PL10D PL11D PL12D PL13D PL14D PL18D PL21D I/O-A12
42 PL9C PL10C PL11C PL12C PL13B PL14B PL18B PL21B I/O
43 PL9B PL10B PL11B PL12B PL14D PL15D PL19D PL22D I/O
Notes:
The OR2C04A and OR2T04A do not have bond pads connected to 208-pin SQFP package pin numbers 6, 45, 47, 56, 60, 102, 153, 154, 166,
201, and 203.
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, but they are connected to VDD5 f or the OR2TxxA series.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
82 Lucent Technologies Inc.
44 PL9A PL10A PL11A PL13D PL14B PL15B PL19B PL22B I/O-A13
45 See Note PL11D PL12D PL13B PL15D PL16D PL20D PL2 3D I/O
46 PL10D PL11A PL12A PL14C PL16D PL17D PL21D PL25A I/O-A14
47 See Note PL12D PL13D PL15D PL17D PL18D PL22D PL27D I / O
48 PL10C PL12C PL13A PL15A PL17A PL19D PL23D PL28D I/O
49 PL10B PL12B PL14D PL16D PL18C PL19A PL23A PL28A I/O
50 PL10A PL12A PL14A PL16A PL18A PL20A PL24A PL30A I/O-A15
51 VSS VSS VSS VSS VSS VSS VSS VSS VSS
52 CCLK CCLK CCLK CCLK CCLK CCLK CCLK CCLK CCLK
53 VSS VSS VSS VSS VSS VSS VSS VSS VSS
54 VSS VSS VSS VSS VSS VSS VSS VSS VSS
55 PB1A PB1A PB1A PB1A PB1A PB1A PB1A PB1A I/O-A16
56 See Note PB1B PB1D PB1D PB1D PB2A PB2A PB3A I/O
57 PB1B PB1C PB2A PB2A PB2A PB2D PB2D PB3D I/O-VDD5
58 PB1C PB1D PB2D PB2D PB2D PB3D PB3D PB4D I/O
59 PB1D PB2A PB3A PB3B PB3D PB4D PB4D PB5D I/O-A17
60 See Note PB2D PB3D PB4D PB4D P B5D PB5D PB6D I/O
61 PB2A PB3A PB4A PB5A PB5B PB6B PB6B PB7D I/O
62 PB2B PB3B PB4B PB5B PB5D PB6D PB6D PB8D I/O
63 PB2C PB3C PB4C PB5C PB6B PB7B PB7B PB9D I/O
64 PB2D PB3D PB4D PB5D PB6D PB7D PB7D PB10D I/O
65 VDD VDD VDD VDD VDD VDD VDD VDD VDD
66 PB3A PB4A PB5A PB6A PB7A PB8A PB8A PB11A I/O
67 PB3B PB4B PB5B PB6B PB7B PB8B PB8D PB11D I/O
68 PB3C PB4C PB5C PB6C PB7C PB8C PB9A PB12A I/O
69 PB3D PB4D PB5D PB6D PB7D PB8D PB9D PB12D I/O
70 PB4A PB5A PB6A PB7A PB8A PB9A PB10A PB13A I/O
71 PB4B PB5B PB6B PB7B PB8B PB9B PB10D PB13D I/O
72 PB4C PB5C PB6C PB7C PB8C PB9C PB11A PB14A I/O
73 PB4D PB5D PB6D PB7D PB8D PB9D PB11D PB14D I/O
74 VSS VSS VSS VSS VSS VSS VSS VSS VSS
75 PB5A PB6A PB7A PB8A PB9A PB10A PB12A PB15A I/O
76 PB5B PB6B PB7B PB8B PB9B PB10B PB12B PB15B I/O
77 PB5C PB6C PB7C PB8C PB9C PB10C PB12C PB15C I/O
78 PB5D PB6D PB7D PB8D PB9D PB10D PB12D PB15D I/O
79 VSS VSS VSS VSS VSS VSS VSS VSS VSS
80 PB6A PB7A PB8A PB9A PB10A PB11A PB13A PB16A I/O
81 PB6B PB7B PB8B PB9B PB10B PB11B PB13B PB16B I/O
82 PB6C PB7C PB8C PB9C PB10C PB11C PB13C PB16C I/O
83 PB6D PB7D PB8D PB9D PB10D PB11D PB13D PB16D I/O
84 VSS VSS VSS VSS VSS VSS VSS VSS VSS
85 PB7A PB8A PB9A PB10A PB11A PB12A PB14A PB17A I/O-VDD5
86 PB7B PB8B PB9B PB10B PB11B PB12B PB14D PB17D I/O
Pin Information (continued)
Table 23. OR2C/2T04A, OR2C/2T06A, OR2C/2T08A, OR2C/2T10A, OR2C/2T12A, OR2C/2T15A/B,
OR2C/2T26A, and OR2C/2T40A/B 208-Pin SQFP/SQFP2 Pinout (continued)
Pin 2C/2T04A
Pad 2C/2T06A
Pad 2C/2T08A
Pad 2C /2T10A
Pad 2C/2T12A
Pad 2 C/2T1 5A/B
Pad 2C/2T26A
Pad 2C /2T40A/B
Pad Function
Notes:
The OR2C04A and OR2T04A do not have bond pads connected to 208-pin SQFP package pin numbers 6, 45, 47, 56, 60, 102, 153, 154, 166,
201, and 203.
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, but they are connected to VDD5 f or the OR2TxxA series.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 83
87 PB7C PB8C PB9C PB10C PB11C PB12C PB15A PB18A I/O
88 PB7D PB8D PB9D PB10D PB11D PB12D PB15D PB18D I/O
89 PB8A PB9A PB10A PB11A PB12A PB13A PB16A PB19A I/O-HDC
90 PB8B PB9B PB10B PB11B PB12B PB13B PB16D PB19D I/O
91 PB8C PB9C PB10C PB11C PB12C PB13C PB17A PB20A I/O
92 PB8D PB9D PB10D PB11D PB12D PB13D PB17D PB20D I/O
93 VDD VDD VDD VDD VDD VDD VDD VDD VDD
94 PB9A PB10A PB11A PB12A PB13A PB14A PB18A PB21A I/O-LDC
95 PB9B PB10B PB11D PB13A PB13D PB14D PB18D PB22D I/O
96 PB9C PB10C PB12A PB13B PB14A PB15A PB19A PB23A I/O
97 PB9D PB10D PB12B PB13C PB14D PB15D PB19D PB24D I/O
98 PB10A PB11A PB12C PB13D PB15A PB16A PB20A PB25A I/O-INIT
99 PB10B PB11C PB12D PB14A PB16A PB17A PB21A PB26A I/O
100 PB10C PB11D PB13A PB15A PB17A PB18A PB22A PB27A I/O
101 PB10D PB12A PB13D PB15D PB18A PB19D PB23D PB28D I/O
102 See N ote PB12 D PB14D PB16 D PB18D PB20D PB24D PB30D I/O
103 VSS VSS VSS VSS VSS VSS VSS VSS VSS
104 DONE DONE DONE DONE DONE DONE DONE DONE DONE
105 VSS VSS VSS VSS VSS VSS VSS VSS VSS
106 RESET RESET RESET RESET RESET RESET RESET RESET RESET
107 PRGM PRGM PRGM PRGM PRGM PRGM PRGM PRGM PRGM
108 PR10A PR12A PR14A PR16A PR18A PR20A PR24A PR30A I/O-M0
109 PR10B PR12D PR13A PR15A PR18D PR19A PR23A PR28A I/O
110 PR10C PR11A PR13D PR15D PR17B PR18A PR22A PR27A I/O
111 PR10D PR11B PR12A PR14A PR16A PR17A PR21A PR26A I/O
112 PR9A PR10A PR11A PR13B PR15D PR16D PR20D PR23D I/O-M1
113 PR9B PR10B PR11B PR13C PR14A PR15A PR19A PR22A I/O
114 PR9C PR10C PR11C PR12A PR14D PR15D PR19D PR22D I/O-VDD5
115 PR9D PR10D PR11D PR12B PR13A PR14A PR18A PR21A I/O
116 VDD VDD VDD VDD VDD VDD VDD VDD VDD
117 PR8A PR9A PR10A PR11A PR12A PR13A PR17A PR20A I/O-M2
118 PR8B PR9B PR10B PR11B PR12B PR13B PR17D PR20D I/O
119 PR8C PR9C PR10C PR11C PR12C PR13C PR16A PR19A I/O
120 PR8D PR9D PR10D PR11D PR12D PR13D PR16D PR19D I/O
121 PR7A PR8A PR9A PR10A PR11A PR12A PR15A PR18A I/O-M3
122 PR7B PR8B PR9B PR10B PR11B PR12B PR15D PR18D I/O
123 PR7C PR8C PR9C PR10C PR11C PR12C PR14A PR17A I/O
124 PR7D PR8D PR9D PR10D PR11D PR12D PR14D PR17D I/O
125 VSS VSS VSS VSS VSS VSS VSS VSS VSS
126 PR6A PR7A PR8A PR9A PR10A PR11A PR13A PR16A I/O
127 PR6B PR7B PR8B PR9B PR10B PR11B PR13B PR16B I/O
128 PR6C PR7C PR8C PR9C PR10C PR11C PR13C PR16C I/O
129 PR6D PR7D PR8D PR9D PR10D PR11D PR13D PR16D I/O
Pin Information (continued)
Table 23. OR2C/2T04A, OR2C/2T06A, OR2C/2T08A, OR2C/2T10A, OR2C/2T12A, OR2C/2T15A/B,
OR2C/2T26A, and OR2C/2T40A/B 208-Pin SQFP/SQFP2 Pinout (continued)
Pin 2C/2T04A
Pad 2C/2T06A
Pad 2C/2T08A
Pad 2C /2T10A
Pad 2C/2T12A
Pad 2C / 2T15A/B
Pad 2C/2T26A
Pad 2C /2T40A/B
Pad Function
Notes:
The OR2C04A and OR2T04A do not have bond pads connected to 208-pin SQFP package pin numbers 6, 45, 47, 56, 60, 102, 153, 154, 166,
201, and 203.
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, but they are connected to VDD5 f or the OR2TxxA series.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
84 Lucent Technologies Inc.
130 VDD VDD VDD VDD VDD VDD VDD VDD VDD
131 PR5A PR6A PR7A PR8A PR9A PR10A PR12A PR15A I/O
132 PR5B PR6B PR7B PR8B PR9B PR10B PR12B PR15B I/O
133 PR5C PR6C PR7C PR8C PR9C PR10C PR12C PR15C I/O
134 PR5D PR6D PR7D PR8D PR9D PR10D PR12D PR15D I/O
135 VSS VSS VSS VSS VSS VSS VSS VSS VSS
136 PR4A PR5A PR6A PR7A PR8A PR9A PR11A PR14A I/O-VDD5
137 PR4B PR5B PR6B PR7B PR8B PR9B PR11D PR14D I/O
138 PR4C PR5C PR6C PR7C PR8C PR9C PR10A PR13A I/O
139 PR4D PR5D PR6D PR7D PR8D PR9D PR10D PR13D I/O
140 PR3A PR4A PR5A PR6A PR7A PR8A PR9A PR12A I/O-CS1
141 PR3B PR4B PR5B PR6B PR7B PR8B PR9D PR12D I/O
142 PR3C PR4C PR5C PR6C PR7C PR8C PR8A PR11A I/O
143 PR3D PR4D PR5D PR6D PR7D PR8D PR8D PR11D I/O
144 VDD VDD VDD VDD VDD VDD VDD VDD VDD
145 PR2A PR3A PR4A PR5A PR6A PR7A PR7A PR10A I/O-CS0
146 PR2B PR3B PR4B PR4B PR6B PR7B PR7B PR10B I/O
147 PR2C PR3C PR4C PR4C PR5B PR6B PR6B PR9B I/O
148 PR2D PR3D PR4D PR4D PR5D PR6D PR6D PR9D I/O
149 PR1A PR2A PR3A PR3A PR4A PR5A PR5A PR8A I/O-RD
150 PR1B PR2C PR3C PR3C PR4D PR5D PR5D PR6A I/O
151 PR1C PR2D PR3D PR3D PR3A PR4A PR4A PR5A I/O
152 PR1D PR1A PR2A PR2A PR2A PR3A PR3A PR4A I/O-WR
153 See Note PR1C PR2D PR2D PR2C PR2A PR2A PR3A I/O
154 See Not e PR1D PR1A PR1A PR1A PR1A PR1A PR2A I/O
155 VSS VSS VSS VSS VSS VSS VSS VSS VSS
156 RD_CFG RD_CFG RD_CFG RD_CFG RD_CFG RD_CFG RD_CFG RD_CFG RD_CFG
157 VSS VSS VSS VSS VSS VSS VSS VSS VSS
158 VSS VSS VSS VSS VSS VSS VSS VSS VSS
159 PT10D PT12D PT14D PT16D PT18D PT20D PT24D PT30D I/O
160 PT10C PT12A PT13D PT15D PT17D PT19A PT23A PT28A I/O-RDY/RCLK
161 PT10B PT11D PT13A PT15A PT16D PT17D PT21D PT26D I/O
162 PT10A PT11C PT12D PT14D PT16A PT17A PT21A PT26A I/O
163 PT9D PT11A PT12C PT13D PT15D PT16D PT20D PT25D I/O-D7
164 PT9C PT10D PT12A PT13B PT14D PT15D PT19D PT24D I/O-VDD5
165 PT9B PT10C PT11D PT13A PT14A PT15A PT19A PT23D I/O
166 See Not e PT10B PT11C PT12D PT13D PT14D PT18D PT22D I/O
167 PT9A PT10A PT11B PT12B PT13B PT14B PT18B PT21D I/O-D6
168 VDD VDD VDD VDD VDD VDD VDD VDD VDD
169 PT8D PT9D PT10D PT11D PT12D PT13D PT17D PT20D I/O
170 PT8C PT9C PT10C PT11C PT12C PT13C PT17A PT20A I/O
171 PT8B PT9B PT10B PT11B PT12B PT13B PT16D PT19D I/O
172 PT8A PT9A PT10A PT11A PT12A PT13A PT16A PT19A I/O-D5
Pin Information (continued)
Table 23. OR2C/2T04A, OR2C/2T06A, OR2C/2T08A, OR2C/2T10A, OR2C/2T12A, OR2C/2T15A/B,
OR2C/2T26A, and OR2C/2T40A/B 208-Pin SQFP/SQFP2 Pinout (continued)
Pin 2C/2T04A
Pad 2C/2T06A
Pad 2C/2T08A
Pad 2C /2T10A
Pad 2C/2T12A
Pad 2 C/2T1 5A/B
Pad 2C/2T26A
Pad 2C /2T40A/B
Pad Function
Notes:
The OR2C04A and OR2T04A do not have bond pads connected to 208-pin SQFP package pin numbers 6, 45, 47, 56, 60, 102, 153, 154, 166,
201, and 203.
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, but they are connected to VDD5 f or the OR2TxxA series.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 85
173 PT7D PT8D PT9D PT10D PT11D PT12D PT15D PT18D I/O
174 PT7C PT8C PT9C PT10C PT11C PT12C PT15A PT18A I/O
175 PT7B PT8B PT9B PT10B PT11B PT12B PT14D PT17D I/O
176 PT7A PT8A PT9A PT10A PT11A PT12A PT14A PT17A I/O-D4
177 VSS VSS VSS VSS VSS VSS VSS VSS VSS
178 PT6D PT7D PT8D PT9D PT10D PT11D PT13D PT16D I/O
179 PT6C PT7C PT8C PT9C PT10C PT11C PT13C PT16C I/O
180 PT6B PT7B PT8B PT9B PT10B PT11B PT13B PT16B I/O
181 PT6A PT7A PT8A PT9A PT10A PT11A PT13A PT16A I/O-D3
182 VSS VSS VSS VSS VSS VSS VSS VSS VSS
183 PT5D PT6D PT7D PT8D PT9D PT10D PT12D PT15D I/O
184 PT5C PT6C PT7C PT8C PT9C PT10C PT12C PT15C I/O
185 PT5B PT6B PT7B PT8B PT9B PT10B PT12B PT15B I/O-VDD5
186 PT5A PT6A PT7A PT8A PT9A PT10A PT12A PT15A I/O-D2
187 VSS VSS VSS VSS VSS VSS VSS VSS VSS
188 PT4D PT5D PT6D PT7D PT8D PT9D PT11D PT14D I/O-D1
189 PT4C PT5C PT6C PT7C PT8C PT9C PT11A PT14A I/O
190 PT4B PT5B PT6B PT7B PT8B PT9B PT10D PT13D I/O
191 PT4A PT5A PT6A PT7A PT8A PT9A PT10A PT13A I/O-D0/DIN
192 PT3D PT4D PT5D PT6D PT7D PT8D PT9D PT12D I/O
193 PT3C PT4C PT5C PT6C PT7C PT8C PT9A PT12A I/O
194 PT3B PT4B PT5B PT6B PT7B PT8B PT8D PT11D I/O
195 PT3A PT4A PT5A PT6A PT7A PT8A PT8A PT11A I/O-DOUT
196 VDD VDD VDD VDD VDD VDD VDD VDD VDD
197 PT2D PT3D PT4D PT5D PT6D PT7D PT7D PT10D I/O
198 PT2C PT3C PT4C PT5A PT6A PT7A PT7A PT9A I/O
199 PT2B PT3B PT4B PT4D PT5C PT6C PT6C PT8A I/O
200 PT2A PT3A PT4A PT4A PT5A PT6A PT6A PT7A I/O-TDI
201 See N ote PT2 D PT3D PT3D PT4A PT5A PT5A PT6A I/O
202 PT1D PT2A PT3A PT3A PT3A PT4A PT4A PT5A I/O-TMS
203 See N ote PT1 D PT2D PT2D PT2C PT3A PT3A P T4A I/O
204 PT1C PT1C PT2A PT2A PT2A PT2A PT2A PT3A I/O
205 PT1B PT1B PT1D PT1D PT1D PT1D PT1D PT2D I/O
206 PT1A PT1A PT1A PT1A PT1A PT1A PT1A PT1A I/O-TCK
207 VSS VSS VSS VSS VSS VSS VSS VSS VSS
208 RD_DATA/
TDO RD_DATA/
TDO RD_DATA/
TDO RD_DATA/
TDO RD_DATA/
TDO RD_DATA/
TDO RD_DATA/
TDO RD_DATA/
TDO RD_DATA/TDO
Pin Information (continued)
Table 23. OR2C/2T04A, OR2C/2T06A, OR2C/2T08A, OR2C/2T10A, OR2C/2T12A, OR2C/2T15A/B,
OR2C/2T26A, and OR2C/2T40A/B 208-Pin SQFP/SQFP2 Pinout (continued)
Pin 2C/2T04A
Pad 2C/2T06A
Pad 2C/2T08A
Pad 2C /2T10A
Pad 2C/2T12A
Pad 2C / 2T15A/B
Pad 2C/2T26A
Pad 2C /2T40A/B
Pad Function
Notes:
The OR2C04A and OR2T04A do not have bond pads connected to 208-pin SQFP package pin numbers 6, 45, 47, 56, 60, 102, 153, 154, 166,
201, and 203.
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, but they are connected to VDD5 f or the OR2TxxA series.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
86 Lucent Technologies Inc.
Pin Information (continued)
Table 24. OR2C/2T06A, OR2C/2T08A, OR2C/2T10A, OR2C/2T12A, OR2C/2T15A/B, OR2C/2T26A,
and OR2C/2T40A/B 240-Pin SQFP/SQFP2 Pinout
Pin 2C/2T06A
Pad 2C/2T08A
Pad 2C/2T10A
Pad 2C/2T12A
Pad 2C/2T15A/B
Pad 2C/2T26A
Pad 2C/2T40A/B
Pad Function
1V
SS VSS VSS VSS VSS VSS VSS VSS
2V
DD VDD VDD VDD VDD VDD VDD VDD
3 PL1D PL1D PL1D PL1D PL1D PL1D PL1D I/O
4 PL1C PL1B PL1B PL1C PL1C PL1C PL1A I/O
5 PL1B PL1A PL1A PL1B PL1B PL1B PL2D I/O
6 PL1A PL2D PL2D PL2D PL2D PL2D PL3D I/O-A0
7V
SS VSS VSS VSS VSS VSS VSS VSS
8 PL2D PL3D PL3D PL3D PL4D PL4D PL5D I/O-VDD5
9 PL2C PL3C PL3C PL3A PL4A PL4A PL6D I/O
10 PL2B PL3B PL3B PL4D PL5D PL5D PL7D I/O
11 PL2A PL3A PL3A PL4A PL5A PL5A PL8D I/O-A1
12 PL3D PL4D PL4A PL5A PL6A PL6A PL9A I/O-A2
13 PL3C PL4C PL5C PL6D PL7D PL7D PL10D I/O
14 PL3B PL4B PL5B PL6B PL7B PL7B PL10B I/O
15 PL3A PL4A PL5A PL6A PL7A PL7A PL10A I/O-A3
16 VDD VDD VDD VDD VDD VDD VDD VDD
17 PL4D PL5D PL6D PL7D PL8D PL8D PL11D I/O
18 PL4C PL5C PL6C PL7C PL8C PL8A PL11A I/O
19 PL4B PL5B PL6B PL7B PL8B PL9D PL12D I/O
20 PL4A PL5A PL6A PL7A PL8A PL9A PL12A I/O-A4
21 PL5D PL6D PL7D PL8D PL9D PL10D PL13D I/O-A5
22 PL5C PL6C PL7C PL8C PL9C PL10A PL13A I/O
23 PL5B PL6B PL7B PL8B PL9B PL11D PL14D I/O
24 PL5A PL6A PL7A PL8A PL9A PL11A PL14A I/O-A6
25 VSS VSS VSS VSS VSS VSS VSS VSS
26 PL6D PL7D PL8D PL9D PL10D PL12D PL15D I/O
27 PL6C PL7C PL8C PL9C PL10C PL12C PL15C I/O
28 PL6B PL7B PL8B PL9B PL10B PL12B PL15B I/O
29 PL6A PL7A PL8A PL9A PL10A PL12A PL15A I/O-A7
30 VDD VDD VDD VDD VDD VDD VDD VDD
31 PL7D PL8D PL9D PL10D PL11D PL13D PL16D I/O
32 PL7C PL8C PL9C PL10C PL11C PL13C PL16C I/O-VDD5
33 PL7B PL8B PL9B PL10B PL11B PL13B PL16B I/O
34 PL7A PL8A PL9A PL10A PL11A PL13A PL16A I/O-A8
35 VSS VSS VSS VSS VSS VSS VSS VSS
36 PL8D PL9D PL10D PL11D PL12D PL14D PL17D I/O-A9
37 PL8C PL9C PL10C PL11C PL12C PL14A PL17A I/O
38 PL8B PL9B PL10B PL11B PL12B PL15D PL18D I/O
39 PL8A PL9A PL10A PL11A PL12A PL15A PL18A I/O-A10
40 PL9D PL10D PL11D PL12D PL13D PL16D PL19D I/O
41 PL9C PL10C PL11C PL12C PL13C PL16A PL19A I/O
42 PL9B PL10B PL11B PL12B PL13B PL17D PL20D I/O
Notes:
The OR2C/2T08A and OR2C/2T10A do not have bond pads connected to 240-pin SQFP package pin numbers 113 and 188.
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, but they are connected to VDD5 for the OR2TxxA series.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 87
43 PL9A PL10A PL11A PL12A PL13A PL17A PL20A I/O-A11
44 VDD VDD VDD VDD VDD VDD VDD VDD
45 PL10D PL11D PL12D PL13D PL14D PL18D PL21D I/O-A12
46 PL10C PL11C PL12C PL13B PL14B PL18B PL21B I/O
47 PL10B PL11B PL12B PL14D PL15D PL19D PL22D I/O
48 PL10A PL11A PL13D PL14B PL15B PL19B PL22B I/O-A13
49 PL11D PL12D PL13B PL14A PL15A PL19A PL22A I/O
50 PL11C PL12C PL13A PL15D PL16D PL20D PL23D I/O
51 PL11B PL12B PL14D PL15B PL16B PL20B PL24D I/O
52 PL11A PL12A PL14C PL16D PL17D PL21D PL25A I/O-A14
53 VSS VSS VSS VSS VSS VSS VSS VSS
54 PL12D PL13D PL15D PL17D PL18D PL22D PL27D I/O
55 PL12C PL13A PL15A PL17A PL19D PL23D PL28D I/O
56 PL12B PL14D PL16D PL18C PL19A PL23A PL28A I/O
57 PL12A PL14A PL16A PL18A PL20A PL24A PL30A I/O-A15
58 VSS VSS VSS VSS VSS VSS VSS VSS
59 CCLK CCLK CCLK CCLK CCLK CCLK CCLK CCLK
60 VDD VDD VDD VDD VDD VDD VDD VDD
61 VSS VSS VSS VSS VSS VSS VSS VSS
62 VSS VSS VSS VSS VSS VSS VSS VSS
63 PB1A PB1A PB1A PB1A PB1A PB1A PB1A I/O-A16
64 PB1B PB1D PB1D PB1D PB2A PB2A PB3A I/O
65 PB1C PB2A PB2A PB2A PB2D PB2D PB3D I/O-VDD5
66 PB1D PB2D PB2D PB2D PB3D PB3D PB4D I/O
67 VSS VSS VSS VSS VSS VSS VSS VSS
68 PB2A PB3A PB3B PB3D PB4D PB4D PB5D I/O-A17
69 PB2B PB3B PB4B PB4D PB5D PB5D PB6D I/O
70 PB2C PB3C PB4C PB5A PB6A PB6A PB7A I/O
71 PB2D PB3D PB4D PB5B PB6B PB6B PB7D I/O
72 PB3A PB4A PB5A PB5D PB6D PB6D PB8D I/O
73 PB3B PB4B PB5B PB6A PB7A PB7A PB9A I/O
74 PB3C PB4C PB5C PB6B PB7B PB7B PB9D I/O
75 PB3D PB4D PB5D PB6D PB7D PB7D PB10D I/O
76 VDD VDD VDD VDD VDD VDD VDD VDD
77 PB4A PB5A PB6A PB7A PB8A PB8A PB11A I/O
78 PB4B PB5B PB6B PB7B PB8B PB8D PB11D I/O
79 PB4C PB5C PB6C PB7C PB8C PB9A PB12A I/O
80 PB4D PB5D PB6D PB7D PB8D PB9D PB12D I/O
81 PB5A PB6A PB7A PB8A PB9A PB10A PB13A I/O
82 PB5B PB6B PB7B PB8B PB9B PB10D PB13D I/O
83 PB5C PB6C PB7C PB8C PB9C PB11A PB14A I/O
84 PB5D PB6D PB7D PB8D PB9D PB11D PB14D I/O
Pin Information (continued)
Table 24. OR2C/2T06A, OR2C/2T08A, OR2C/2T10A, OR2C/2T12A, OR2C/2T15A/B, OR2C/2T26A,
and OR2C/2T40A/B 240-Pin SQFP/SQFP2 Pinout (continued)
Pin 2C/2T06A
Pad 2C/2T08A
Pad 2C/2T10A
Pad 2C/2T12A
Pad 2C/2T15A/B
Pad 2C/2T26A
Pad 2C/2T40A/B
Pad Function
Notes:
The OR2C/2T08A and OR2C/2T10A do not have bond pads connected to 240-pin SQFP package pin numbers 113 and 188.
The pins labeled I/O-VDD5 are user I/Os for the OR 2CxxA and OR2TxxB series, but they are c onnected to VDD5 for the OR2TxxA series.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
88 Lucent Technologies Inc.
85 VSS VSS VSS VSS VSS VSS VSS VSS
86 PB6A PB7A PB8A PB9A PB10A PB12A PB15A I/O
87 PB6B PB7B PB8B PB9B PB10B PB12B PB15B I/O
88 PB6C PB7C PB8C PB9C PB10C PB12C PB15C I/O
89 PB6D PB7D PB8D PB9D PB10D PB12D PB15D I/O
90 VSS VSS VSS VSS VSS VSS VSS VSS
91 PB7A PB8A PB9A PB10A PB11A PB13A PB16A I/O
92 PB7B PB8B PB9B PB10B PB11B PB13B PB16B I/O
93 PB7C PB8C PB9C PB10C PB11C PB13C PB16C I/O
94 PB7D PB8D PB9D PB10D PB11D PB13D PB16D I/O
95 VSS VSS VSS VSS VSS VSS VSS VSS
96 PB8A PB9A PB10A PB11A PB12A PB14A PB17A I/O-VDD5
97 PB8B PB9B PB10B PB11B PB12B PB14D PB17D I/O
98 PB8C PB9C PB10C PB11C PB12C PB15A PB18A I/O
99 PB8D PB9D PB10D PB11D PB12D PB15D PB18D I/O
100 PB9A PB10A PB11A PB12A PB13A PB16A PB19A I/O-HDC
101 PB9B PB10B PB11B PB12B PB13B PB16D PB19D I/O
102 PB9C PB10C PB11C PB12C PB13C PB17A PB20A I/O
103 PB9D PB10D PB11D PB12D PB13D PB17D PB20D I/O
104 VDD VDD VDD VDD VDD VDD VDD VDD
105 PB10A PB11A PB12A PB13A PB14A PB18A PB21A I/O-LDC
106 PB10B PB11D PB13A PB13D PB14D PB18D PB22D I/O
107 PB10C PB12A PB13B PB14A PB15A PB19A PB23A I/O
108 PB10D PB12B PB13C PB14D PB15D PB19D PB24D I/O
109 PB11A PB12C PB13D PB15A PB16A PB20A PB25A I/O-INIT
110 PB11B PB12D PB14A PB15D PB16D PB20D PB25D I/O
111 PB11C PB13A PB15A PB16A PB17A PB21A PB26A I/O
112 PB11D PB13B PB15B PB16D PB17D PB21D PB26D I/O
113 VSS See Note See Note VSS VSS VSS VSS VSS
114 PB12A PB13D PB15D PB17A PB18A PB22A PB27A I/O
115 PB12B PB14A PB16A PB17D PB19A PB23A PB28A I/O
116 PB12C PB14B PB16B PB18A PB19D PB23D PB28D I/O
117 PB12D PB14D PB16D PB18D PB20D PB24D PB30D I/O
118 VSS VSS VSS VSS VSS VSS VSS VSS
119 DONE DONE DONE DONE DONE DONE DONE DONE
120 VDD VDD VDD VDD VDD VDD VDD VDD
121 VSS VSS VSS VSS VSS VSS VSS VSS
122 RESET RESET RESET RESET RESET RESET RESET RESET
123 PRGM PRGM PRGM PRGM PRGM PRGM PRGM PRGM
124 PR12A PR14A PR16A PR18A PR20A PR24A PR30A I/O-M0
125 PR12B PR14D PR16D PR18C PR20D PR24D PR29D I/O
126 PR12C PR13A PR15A PR18D PR19A PR23A PR28A I/O
Pin Information (continued)
Table 24. OR2C/2T06A, OR2C/2T08A, OR2C/2T10A, OR2C/2T12A, OR2C/2T15A/B, OR2C/2T26A,
and OR2C/2T40A/B 240-Pin SQFP/SQFP2 Pinout (continued)
Pin 2C/2T06A
Pad 2C/2T08A
Pad 2C/2T10A
Pad 2C/2T12A
Pad 2C/2T15A/B
Pad 2C/2T26A
Pad 2C/2T40A/B
Pad Function
Notes:
The OR2C/2T08A and OR2C/2T10A do not have bond pads connected to 240-pin SQFP package pin numbers 113 and 188.
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, but they are connected to VDD5 for the OR2TxxA series.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 89
127 PR12D PR13D PR15D PR17B PR18A PR22A PR27A I/O
128 VSS VSS VSS VSS VSS VSS VSS VSS
129 PR11A PR12A PR14A PR16A PR17A PR21A PR26A I/O
130 PR11B PR12B PR14C PR16D PR17D PR21D PR25A I/O
131 PR11C PR12C PR14D PR15A PR16A PR20A PR24A I/O
132 PR11D PR12D PR13A PR15C PR16C PR20C PR24D I/O
133 PR10A PR11A PR13B PR15D PR16D PR20D PR23D I/O-M1
134 PR10B PR11B PR13C PR14A PR15A PR19A PR22A I/O
135 PR10C PR11C PR12A PR14D PR15D PR19D PR22D I/O-VDD5
136 PR10D PR11D PR12B PR13A PR14A PR18A PR21A I/O
137 VDD VDD VDD VDD VDD VDD VDD VDD
138 PR9A PR10A PR11A PR12A PR13A PR17A PR20A I/O-M2
139 PR9B PR10B PR11B PR12B PR13B PR17D PR20D I/O
140 PR9C PR10C PR11C PR12C PR13C PR16A PR19A I/O
141 PR9D PR10D PR11D PR12D PR13D PR16D PR19D I/O
142 PR8A PR9A PR10A PR11A PR12A PR15A PR18A I/O-M3
143 PR8B PR9B PR10B PR11B PR12B PR15D PR18D I/O
144 PR8C PR9C PR10C PR11C PR12C PR14A PR17A I/O
145 PR8D PR9D PR10D PR11D PR12D PR14D PR17D I/O
146 VSS VSS VSS VSS VSS VSS VSS VSS
147 PR7A PR8A PR9A PR10A PR11A PR13A PR16A I/O
148 PR7B PR8B PR9B PR10B PR11B PR13B PR16B I/O
149 PR7C PR8C PR9C PR10C PR11C PR13C PR16C I/O
150 PR7D PR8D PR9D PR10D PR11D PR13D PR16D I/O
151 VDD VDD VDD VDD VDD VDD VDD VDD
152 PR6A PR7A PR8A PR9A PR10A PR12A PR15A I/O
153 PR6B PR7B PR8B PR9B PR10B PR12B PR15B I/O
154 PR6C PR7C PR8C PR9C PR10C PR12C PR15C I/O
155 PR6D PR7D PR8D PR9D PR10D PR12D PR15D I/O
156 VSS VSS VSS VSS VSS VSS VSS VSS
157 PR5A PR6A PR7A PR8A PR9A PR11A PR14A I/O-VDD5
158 PR5B PR6B PR7B PR8B PR9B PR11D PR14D I/O
159 PR5C PR6C PR7C PR8C PR9C PR10A PR13A I/O
160 PR5D PR6D PR7D PR8D PR9D PR10D PR13D I/O
161 PR4A PR5A PR6A PR7A PR8A PR9A PR12A I/O-CS1
162 PR4B PR5B PR6B PR7B PR8B PR9D PR12D I/O
163 PR4C PR5C PR6C PR7C PR8C PR8A PR11A I/O
164 PR4D PR5D PR6D PR7D PR8D PR8D PR11D I/O
165 VDD VDD VDD VDD VDD VDD VDD VDD
166 PR3A PR4A PR5A PR6A PR7A PR7A PR10A I/O-CS0
167 PR3B PR4B PR4B PR6B PR7B PR7B PR10B I/O
168 PR3C PR4C PR4C PR5B PR6B PR6B PR9B I/O
Pin Information (continued)
Table 24. OR2C/2T06A, OR2C/2T08A, OR2C/2T10A, OR2C/2T12A, OR2C/2T15A/B, OR2C/2T26A,
and OR2C/2T40A/B 240-Pin SQFP/SQFP2 Pinout (continued)
Pin 2C/2T06A
Pad 2C/2T08A
Pad 2C/2T10A
Pad 2C/2T12A
Pad 2C/2T15A/B
Pad 2C/2T26A
Pad 2C/2T40A/B
Pad Function
Notes:
The OR2C/2T08A and OR2C/2T10A do not have bond pads connected to 240-pin SQFP package pin numbers 113 and 188.
The pins labeled I/O-VDD5 are user I/Os for the OR 2CxxA and OR2TxxB series, but they are c onnected to VDD5 for the OR2TxxA series.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
90 Lucent Technologies Inc.
169 PR3D PR4D PR4D PR5D PR6D PR6D PR9D I/O
170 PR2A PR3A PR3A PR4A PR5A PR5A PR8A I/O-RD
171 PR2B PR3B PR3B PR4B PR5B PR5B PR7A I/O
172 PR2C PR3C PR3C PR4D PR5D PR5D PR6A I/O
173 PR2D PR3D PR3D PR3A PR4A PR4A PR5A I/O
174 VSS VSS VSS VSS VSS VSS VSS VSS
175 PR1A PR2A PR2A PR2A PR3A PR3A PR4A I/O-WR
176 PR1B PR2D PR2D PR2C PR2A PR2A PR3A I/O
177 PR1C PR1A PR1A PR1A PR1A PR1A PR2A I/O
178 PR1D PR1D PR1D PR1D PR1D PR1D PR1D I/O
179 VSS VSS VSS VSS VSS VSS VSS VSS
180 RD_CFGN RD_CFGN RD_CFGN RD_CFGN RD_CFGN RD_CFGN RD_CFGN RD_CFGN
181 VSS VSS VSS VSS VSS VSS VSS VSS
182 VDD VDD VDD VDD VDD VDD VDD VDD
183 VSS VSS VSS VSS VSS VSS VSS VSS
184 PT12D PT14D PT16D PT18D PT20D PT24D PT30D I/O
185 PT12C PT14C PT16C PT18B PT20A PT24A PT29A I/O
186 PT12B PT14A PT16A PT18A PT19D PT23D PT28D I/O
187 PT12A PT13D PT15D PT17D PT19A PT23A PT28A I/O-RDY/RCLK
188 VSS See Note See Note VSS VSS VSS VSS VSS
189 PT11D PT13B PT15B PT16D PT17D PT21D PT26D I/O
190 PT11C PT13A PT15A PT16C PT17C PT21C PT26C I/O
191 PT11B PT12D PT14D PT16A PT17A PT21A PT26A I/O
192 PT11A PT12C PT13D PT15D PT16D PT20D PT25D I/O-D7
193 PT10D PT12A PT13B PT14D PT15D PT19D PT24D I/O-VDD5
194 PT10C PT11D PT13A PT14A PT15A PT19A PT23D I/O
195 PT10B PT11C PT12D PT13D PT14D PT18D PT22D I/O
196 PT10A PT11B PT12B PT13B PT14B PT18B PT21D I/O-D6
197 VDD VDD VDD VDD VDD VDD VDD VDD
198 PT9D PT10D PT11D PT12D PT13D PT17D PT20D I/O
199 PT9C PT10C PT11C PT12C PT13C PT17A PT20A I/O
200 PT9B PT10B PT11B PT12B PT13B PT16D PT19D I/O
201 PT9A PT10A PT11A PT12A PT13A PT16A PT19A I/O-D5
202 PT8D PT9D PT10D PT11D PT12D PT15D PT18D I/O
203 PT8C PT9C PT10C PT11C PT12C PT15A PT18A I/O
204 PT8B PT9B PT10B PT11B PT12B PT14D PT17D I/O
205 PT8A PT9A PT10A PT11A PT12A PT14A PT17A I/O-D4
206 VSS VSS VSS VSS VSS VSS VSS VSS
207 PT7D PT8D PT9D PT10D PT11D PT13D PT16D I/O
208 PT7C PT8C PT9C PT10C PT11C PT13C PT16C I/O
209 PT7B PT8B PT9B PT10B PT11B PT13B PT16B I/O
210 PT7A PT8A PT9A PT10A PT11A PT13A PT16A I/O-D3
Pin Information (continued)
Table 24. OR2C/2T06A, OR2C/2T08A, OR2C/2T10A, OR2C/2T12A, OR2C/2T15A/B, OR2C/2T26A,
and OR2C/2T40A/B 240-Pin SQFP/SQFP2 Pinout (continued)
Pin 2C/2T06A
Pad 2C/2T08A
Pad 2C/2T10A
Pad 2C/2T12A
Pad 2C/2T15A/B
Pad 2C/2T26A
Pad 2C/2T40A/B
Pad Function
Notes:
The OR2C/2T08A and OR2C/2T10A do not have bond pads connected to 240-pin SQFP package pin numbers 113 and 188.
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, but they are connected to VDD5 for the OR2TxxA series.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 91
211 VSS VSS VSS VSS VSS VSS VSS VSS
212 PT6D PT7D PT8D PT9D PT10D PT12D PT15D I/O
213 PT6C PT7C PT8C PT9C PT10C PT12C PT15C I/O
214 PT6B PT7B PT8B PT9B PT10B PT12B PT15B I/O-VDD5
215 PT6A PT7A PT8A PT9A PT10A PT12A PT15A I/O-D2
216 VSS VSS VSS VSS VSS VSS VSS VSS
217 PT5D PT6D PT7D PT8D PT9D PT11D PT14D I/O-D1
218 PT5C PT6C PT7C PT8C PT9C PT11A PT14A I/O
219 PT5B PT6B PT7B PT8B PT9B PT10D PT13D I/O
220 PT5A PT6A PT7A PT8A PT9A PT10A PT13A I/O-D0/DIN
221 PT4D PT5D PT6D PT7D PT8D PT9D PT12D I/O
222 PT4C PT5C PT6C PT7C PT8C PT9A PT12A I/O
223 PT4B PT5B PT6B PT7B PT8B PT8D PT11D I/O
224 PT4A PT5A PT6A PT7A PT8A PT8A PT11A I/O-DOUT
225 VDD VDD VDD VDD VDD VDD VDD VDD
226 PT3D PT4D PT5D PT6D PT7D PT7D PT10D I/O
227 PT3C PT4C PT5A PT6A PT7A PT7A PT9A I/O
228 PT3B PT4B PT4D PT5C PT6C PT6C PT8A I/O
229 PT3A PT4A PT4A PT5A PT6A PT6A PT7A I/O-TDI
230 PT2D PT3D PT3D PT4D PT5D PT5D PT6D I/O
231 PT2C PT3C PT3C PT4A PT5A PT5A PT6A I/O
232 PT2B PT3B PT3B PT3D PT4D PT4D PT5D I/O
233 PT2A PT3A PT3A PT3A PT4A PT4A PT5A I/O-TMS
234 VSS VSS VSS VSS VSS VSS VSS VSS
235 PT1D PT2D PT2D PT2C PT3A PT3A PT4A I/O
236 PT1C PT2A PT2A PT2A PT2A PT2A PT3A I/O
237 PT1B PT1D PT1D PT1D PT1D PT1D PT2D I/O
238 PT1A PT1A PT1A PT1A PT1A PT1A PT1A I/O-TCK
239 VSS VSS VSS VSS VSS VSS VSS VSS
240 RD_DATA/
TDO RD_DATA/
TDO RD_DATA/
TDO RD_DATA/
TDO RD_DATA/
TDO RD_DATA/
TDO RD_DATA/
TDO RD_DATA/TDO
Pin Information (continued)
Table 24. OR2C/2T06A, OR2C/2T08A, OR2C/2T10A, OR2C/2T12A, OR2C/2T15A/B, OR2C/2T26A,
and OR2C/2T40A/B 240-Pin SQFP/SQFP2 Pinout (continued)
Pin 2C/2T06A
Pad 2C/2T08A
Pad 2C/2T10A
Pad 2C/2T12A
Pad 2C/2T15A/B
Pad 2C/2T26A
Pad 2C/2T40A/B
Pad Function
Notes:
The OR2C/2T08A and OR2C/2T10A do not have bond pads connected to 240-pin SQFP package pin numbers 113 and 188.
The pins labeled I/O-VDD5 are user I/Os for the OR 2CxxA and OR2TxxB series, but they are c onnected to VDD5 for the OR2TxxA series.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
92 Lucent Technologies Inc.
Pin Information (continued)
Table 25. OR2C/2T06A, OR2C/2T08A, OR2C/2T10A, OR2C/2T12A, and OR2C/2T15A/B
256-Pin PBGA Pinout
Pin 2C/2T06A Pad 2C/2T08A Pad 2C/2T10A Pad 2C/2T12A Pad 2C/2T15A/B Pad Function
C2 PL1D PL1D PL1D PL1D PL1D I/O
D2 PL1C PL1B PL1B PL1C PL1C I/O
D3 PL1B PL1A PL1A PL1B PL1B I/O
E4 PL1A PL2D PL2D PL2D PL2D I/O-A0
C1 — PL2C PL2C PL2C PL2A I/O
D1 — PL2B PL2B PL2B PL3D I/O
E3 — PL2A PL2A PL2A PL3A I/O
E2 PL2D PL3D PL3D PL3D PL4D I/O-VDD5
E1 PL2C PL3C PL3C PL3A PL4A I/O
F3 PL2B PL3B PL3B PL4D PL5D I/O
G4 PL2A PL3A PL3A PL4A PL5A I/O-A1
F2 — — PL4D PL5D PL6D I/O
F1 PL3D PL4D PL4A PL5A PL6A I/O-A2
G3 PL3C PL4C PL5C PL6D PL7D I/O
G2 PL3B PL4B PL5B PL6B PL7B I/O
G1 PL3A PL4A PL5A PL6A PL7A I/O-A3
H3 PL4D PL5D PL6D PL7D PL8D I/O
H2 PL4C PL5C PL6C PL7C PL8C I/O
H1 PL4B PL5B PL6B PL7B PL8B I/O
J4 PL4A PL5A PL6A PL7A PL8A I/O-A4
J3 PL5D PL6D PL7D PL8D PL9D I/O-A5
J2 PL5C PL6C PL7C PL8C PL9C I/O
J1 PL5B PL6B PL7B PL8B PL9B I/O
K2 PL5A PL6A PL7A PL8A PL9A I/O-A6
K3 PL6D PL7D PL8D PL9D PL10D I/O
K1 PL6C PL7C PL8C PL9C PL10C I/O
L1 PL6B PL7B PL8B PL9B PL10B I/O
L2 PL6A PL7A PL8A PL9A PL10A I/O-A7
L3 PL7D PL8D PL9D PL10D PL11D I/O
L4 PL7C PL8C PL9C PL10C PL11C I/O-VDD5
M1 PL7B PL8B PL9B PL10B PL11B I/O
M2 PL7A PL8A PL9A PL10A PL11A I/O-A8
M3 PL8D PL9D PL10D PL11D PL12D I/O-A9
M4 PL8C PL9C PL10C PL11C PL12C I/O
N1 PL8B PL9B PL10B PL11B PL12B I/O
N2 PL8A PL9A PL10A PL11A PL12A I/O-A10
N3 PL9D PL10D PL11D PL12D PL13D I/O
P1 PL9C PL10C PL11C PL12C PL13C I/O
P2 PL9B PL10B PL11B PL12B PL13B I/O
R1 PL9A PL10A PL11A PL12A PL13A I/O-A11
Notes:
The W3 pin on the 256-pin PBGA package is unconnected for all devices listed in this table.
The OR2C/2T08A do not have bond pads connected to the 256-pin PBGA package pins F2 and Y17.
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, b ut they are connected to VDD5 f or the OR2TxxA series.
The pins labeled VSS-ETC are the 4 x 4 array of thermal balls located at the center of the package. The balls can be attached to the ground
plane of the board for enhanced thermal capability (see Table 29) , or they can be left unconnected.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 93
P3 PL10D PL11D PL12D PL13D PL14D I/O-A12
R2 PL10C PL11C PL12C PL13B PL14B I/O
T1 PL10B PL11B PL12B PL14D PL15D I/O
P4 PL10A PL11A PL13D PL14B PL15B I/O-A13
R3 PL11D PL12D PL13B PL14A PL15A I/O
T2 PL11C PL12C PL13A PL15D PL16D I/O
U1 PL11B PL12B PL14D PL15B PL16B I/O
T3 PL11A PL12A PL14C PL16D PL17D I/O-A14
U2 — PL13D PL15D PL17D PL18D I/O-VDD5
V1 PL12D PL13C PL15C PL17C PL18C I/O
T4 PL12C PL13B PL15B PL17B PL18A I/O
U3 PL12B PL13A PL15A PL17A PL19D I/O
V2 — PL14D PL16D PL18D PL19C I/O
W1 — PL14C PL16C PL18C PL19A I/O
V3 — PL14B PL16B PL18B PL20D I/O
W2 PL12A PL14A PL16A PL18A PL20A I/O-A15
Y1 CCLK CCLK CCLK CCLK CCLK CCLK
Y2 PB1A PB1A PB1A PB1A PB1A I/O-A16
W4 — PB1C PB1C PB1C PB1D I/O
V4 PB1B PB1D PB1D PB1D PB2A I/O
U5 PB1C PB2A PB2A PB2A PB2D I/O-VDD5
Y3 PB1D PB2B PB2B PB2B PB3A I/O
Y4 — PB2C PB2C PB2C PB3C I/O
V5 — PB2D PB2D PB2D PB3D I/O
W5 PB2A PB3A PB3B PB3D PB4D I/O-A17
Y5 PB2B PB3B PB4B PB4D PB5D I/O
V6 PB2C PB3C PB4C PB5A PB6A I/O
U7 PB2D PB3D PB4D PB5B PB6B I/O
W6 PB3A PB4A PB5A PB5D PB6D I/O
Y6 PB3B PB4B PB5B PB6A PB7A I/O
V7 PB3C PB4C PB5C PB6B PB7B I/O
W7 PB3D PB4D PB5D PB6D PB7D I/O
Y7 PB4A PB5A PB6A PB7A PB8A I/O
V8 PB4B PB5B PB6B PB7B PB8B I/O
W8 PB4C PB5C PB6C PB7C PB8C I/O
Y8 PB4D PB5D PB6D PB7D PB8D I/O
U9 PB5A PB6A PB7A PB8A PB9A I/O
V9 PB5B PB6B PB7B PB8B PB9B I/O
W9 PB5C PB6C PB7C PB8C PB9C I/O
Y9 PB5D PB6D PB7D PB8D PB9D I/O
Pin Information (continued)
Table 25. OR2C/2T06A, OR2C/2T08A, OR2C/2T10A, OR2C/2T12A, and OR2C/2T15A/B
256-Pin PBGA Pinout (continued)
Pin 2C/2T06A Pad 2C/2T08A Pad 2C/2T10A Pad 2C/2T12A Pad 2C/2T15A/B Pad Function
Notes:
The W3 pin on the 256-pin PBGA package is unconnected for all devices listed in this table.
The OR2C/2T08A do not have bond pads connected to the 256-pin PBGA package pins F2 and Y17.
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, b ut they are connected to VDD5 f or the OR2TxxA series.
The pins labeled VSS-ETC are the 4 x 4 array of thermal balls located at the center of the package. The balls can be attached to the ground
plane of the board for enhanced thermal capability (see Table 29) , or they can be left unconnected.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
94 Lucent Technologies Inc.
W10 PB6A PB7A PB8A PB9A PB10A I/O
V10 PB6B PB7B PB8B PB9B PB10B I/O
Y10 PB6C PB7C PB8C PB9C PB10C I/O
Y11 PB6D PB7D PB8D PB9D PB10D I/O
W11 PB7A PB8A PB9A PB10A PB11A I/O
V11 PB7B PB8B PB9B PB10B PB11B I/O
U11 PB7C PB8C PB9C PB10C PB11C I/O
Y12 PB7D PB8D PB9D PB10D PB11D I/O
W12 PB8A PB9A PB10A PB11A PB12A I/O-VDD5
V12 PB8B PB9B PB10B PB11B PB12B I/O
U12 PB8C PB9C PB10C PB11C PB12C I/O
Y13 PB8D PB9D PB10D PB11D PB12D I/O
W13 PB9A PB10A PB11A PB12A PB13A I/O-HDC
V13 PB9B PB10B PB11B PB12B PB13B I/O
Y14 PB9C PB10C PB11C PB12C PB13C I/O
W14 PB9D PB10D PB11D PB12D PB13D I/O
Y15 PB10A PB11A PB12A PB13A PB14A I/O-LDC
V14 PB10B PB11B PB12C PB13B PB14B I/O
W15 PB10C PB11C PB12D PB13C PB14C I/O
Y16 PB10D PB11D PB13A PB13D PB14D I/O
U14 — PB12A PB13B PB14A PB15A I/O
V15 — PB12B PB13C PB14D PB15D I/O
W16 PB11A PB12C PB13D PB15A PB16A I/O-INIT
Y17 — — PB14A PB15D PB16D I/O
V16 — PB12D PB14B PB16A PB17A I/O-VDD5
W17 PB11B PB13A PB15A PB16D PB17D I/O
Y18 PB11C PB13B PB15B PB17A PB18A I/O
U16 PB11D PB13C PB15C PB17C PB18D I/O
V17 PB12A PB13D PB15D PB17D PB19A I/O
W18 PB12B PB14A PB16A PB18A PB19D I/O
Y19 PB12C PB14B PB16B PB18B PB20A I/O
V18 PB12D PB14C PB16C PB18C PB20B I/O
W19 — PB14D PB16D PB18D PB20D I/O
Y20 DONE DONE DONE DONE DONE DONE
W20 RESET RESET RESET RESET RESET RESET
V19 PRGM PRGM PRGM PRGM PRGM PRGM
U19 PR12A PR14A PR16A PR18A PR20A I/O-M0
U18 — PR14C PR16C PR18C PR20D I/O
T17 — PR14D PR16D PR18D PR19A I/O
V20 — PR13A PR15A PR17A PR19D I/O
Pin Information (continued)
Table 25. OR2C/2T06A, OR2C/2T08A, OR2C/2T10A, OR2C/2T12A, and OR2C/2T15A/B
256-Pin PBGA Pinout (continued)
Pin 2C/2T06A Pad 2C/2T08A Pad 2C/2T10A Pad 2C/2T12A Pad 2 C/2T15A/B Pad Function
Notes:
The W3 pin on the 256-pin PBGA package is unconnected for all devices listed in this table.
The OR2C/2T08A do not have bond pads connected to the 256-pin PBGA package pins F2 and Y17.
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, b ut they are connected to VDD5 f or the OR2TxxA series.
The pins labeled VSS-ETC are the 4 x 4 array of thermal balls located at the center of the package. The balls can be attached to the ground
plane of the board for enhanced thermal capability (see Table 29) , or they can be left unconnected.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 95
U20 PR12B PR13B PR15B PR17B PR18A I/O
T18 PR12C PR13C PR15C PR17C PR18B I/O
T19 PR12D PR13D PR15D PR17D PR18D I/O
T20 PR11A PR12A PR14A PR16A PR17A I/O
R18 PR11B PR12B PR14C PR16D PR17D I/O
P17 PR11C PR12C PR14D PR15A PR16A I/O
R19 PR11D PR12D PR13A PR15C PR16C I/O
R20 PR10A PR11A PR13B PR15D PR16D I/O-M1
P18 PR10B PR11B PR13C PR14A PR15A I/O
P19 PR10C PR11C PR12A PR14D PR15D I/O-VDD5
P20 PR10D PR11D PR12B PR13A PR14A I/O
N18 PR9A PR10A PR11A PR12A PR13A I/O-M2
N19 PR9B PR10B PR11B PR12B PR13B I/O
N20 PR9C PR10C PR11C PR12C PR13C I/O
M17 PR9D PR10D PR11D PR12D PR13D I/O
M18 PR8A PR9A PR10A PR11A PR12A I/O-M3
M19 PR8B PR9B PR10B PR11B PR12B I/O
M20 PR8C PR9C PR10C PR11C PR12C I/O
L19 PR8D PR9D PR10D PR11D PR12D I/O
L18 PR7A PR8A PR9A PR10A PR11A I/O
L20 PR7B PR8B PR9B PR10B PR11B I/O
K20 PR7C PR8C PR9C PR10C PR11C I/O
K19 PR7D PR8D PR9D PR10D PR11D I/O
K18 PR6A PR7A PR8A PR9A PR10A I/O
K17 PR6B PR7B PR8B PR9B PR10B I/O
J20 PR6C PR7C PR8C PR9C PR10C I/O
J19 PR6D PR7D PR8D PR9D PR10D I/O
J18 PR5A PR6A PR7A PR8A PR9A I/O-VDD5
J17 PR5B PR6B PR7B PR8B PR9B I/O
H20 PR5C PR6C PR7C PR8C PR9C I/O
H19 PR5D PR6D PR7D PR8D PR9D I/O
H18 PR4A PR5A PR6A PR7A PR8A I/O-CS1
G20 PR4B PR5B PR6B PR7B PR8B I/O
G19 PR4C PR5C PR6C PR7C PR8C I/O
F20 PR4D PR5D PR6D PR7D PR8D I/O
G18 PR3A PR4A PR5A PR6A PR7A I/O-CS0
F19 PR3B PR4B PR4B PR6B PR7B I/O
E20 PR3C PR4C PR4C PR5B PR6B I/O
G17 PR3D PR4D PR4D PR5D PR6D I/O
F18 PR2A PR3A PR3A PR4A PR5A I/O-RD
Pin Information (continued)
Table 25. OR2C/2T06A, OR2C/2T08A, OR2C/2T10A, OR2C/2T12A, and OR2C/2T15A/B
256-Pin PBGA Pinout (continued)
Pin 2C/2T06A Pad 2C/2T08A Pad 2C/2T10A Pad 2C/2T12A Pad 2C/2T15A/B Pad Function
Notes:
The W3 pin on the 256-pin PBGA package is unconnected for all devices listed in this table.
The OR2C/2T08A do not have bond pads connected to the 256-pin PBGA package pins F2 and Y17.
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, b ut they are connected to VDD5 f or the OR2TxxA series.
The pins labeled VSS-ETC are the 4 x 4 array of thermal balls located at the center of the package. The balls can be attached to the ground
plane of the board for enhanced thermal capability (see Table 29) , or they can be left unconnected.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
96 Lucent Technologies Inc.
E19 PR2B PR3B PR3B PR4B PR5B I/O
D20 PR2C PR3C PR3C PR4D PR5D I/O
E18 PR2D PR3D PR3D PR3A PR4A I/O-VDD5
D19 PR1A PR2A PR2A PR2A PR3A I/O-WR
C20 PR1B PR2B PR2B PR2B PR3B I/O
E17 PR1C PR2C PR2C PR2C PR2A I/O
D18 PR1D PR2D PR2D PR2D PR2D I/O
C19 — PR1A PR1A PR1A PR1A I/O
B20 — PR1B PR1B PR1B PR1B I/O
C18 — PR1C PR1C PR1C PR1C I/O
B19 — PR1D PR1D PR1D PR1D I/O
A20 RD_CFGN RD_CFGN RD_CFGN RD_CFGN RD_CFGN RD_CFGN
A19 — PT14D PT16D PT18D PT20D I/O
B18 PT12D PT14C PT16C PT18C PT20C I/O
B17 PT12C PT14B PT16B PT18B PT20A I/O
C17 PT12B PT14A PT16A PT18A PT19D I/O
D16 PT12A PT13D PT15D PT17D PT19A I/O-RDY/RCLK
A18 — PT13C PT15C PT17A PT18A I/O
A17 PT11D PT13B PT15B PT16D PT17D I/O
C16 PT11C PT13A PT15A PT16C PT17C I/O
B16 PT11B PT12D PT14D PT16A PT17A I/O
A16 PT11A PT12C PT13D PT15D PT16D I/O-D7
C15 — PT12B PT13C PT15A PT16A I/O
D14 PT10D PT12A PT13B PT14D PT15D I/O-VDD5
B15 PT10C PT11D PT13A PT14A PT15A I/O
A15 PT10B PT11C PT12D PT13D PT14D I/O
C14 PT10A PT11B PT12B PT13B PT14B I/O-D6
B14 PT9D PT11A PT12A PT13A PT14A I/O
A14 PT9C PT10D PT11D PT12D PT13D I/O
C13 — PT10C PT11C PT12C PT13C I/O
B13 PT9B PT10B PT11B PT12B PT13B I/O
A13 PT9A PT10A PT11A PT12A PT13A I/O-D5
D12 PT8D PT9D PT10D PT11D PT12D I/O
C12 PT8C PT9C PT10C PT11C PT12C I/O
B12 PT8B PT9B PT10B PT11B PT12B I/O
A12 PT8A PT9A PT10A PT11A PT12A I/O-D4
B11 PT7D PT8D PT9D PT10D PT11D I/O
C11 PT7C PT8C PT9C PT10C PT11C I/O
A11 PT7B PT8B PT9B PT10B PT11B I/O
A10 PT7A PT8A PT9A PT10A PT11A I/O-D3
Pin Information (continued)
Table 25. OR2C/2T06A, OR2C/2T08A, OR2C/2T10A, OR2C/2T12A, and OR2C/2T15A/B
256-Pin PBGA Pinout (continued)
Pin 2C/2T06A Pad 2C/2T08A Pad 2C/2T10A Pad 2C/2T12A Pad 2 C/2T15A/B Pad Function
Notes:
The W3 pin on the 256-pin PBGA package is unconnected for all devices listed in this table.
The OR2C/2T08A do not have bond pads connected to the 256-pin PBGA package pins F2 and Y17.
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, b ut they are connected to VDD5 f or the OR2TxxA series.
The pins labeled VSS-ETC are the 4 x 4 array of thermal balls located at the center of the package. The balls can be attached to the ground
plane of the board for enhanced thermal capability (see Table 29) , or they can be left unconnected.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 97
B10 PT6D PT7D PT8D PT9D PT10D I/O
C10 PT6C PT7C PT8C PT9C PT10C I/O
D10 PT6B PT7B PT8B PT9B PT10B I/O-VDD5
A9 PT6A PT7A PT8A PT9A PT10A I/O-D2
B9 PT5D PT6D PT7D PT8D PT9D I/O-D1
C9 PT5C PT6C PT7C PT8C PT9C I/O
D9 PT5B PT6B PT7B PT8B PT9B I/O
A8 PT5A PT6A PT7A PT8A PT9A I/O-D0/DIN
B8 PT4D PT5D PT6D PT7D PT8D I/O
C8 PT4C PT5C PT6C PT7C PT8C I/O
A7 PT4B PT5B PT6B PT7B PT8B I/O
B7 PT4A PT5A PT6A PT7A PT8A I/O-DOUT
A6 PT3D PT4D PT5D PT6D PT7D I/O
C7 PT3C PT4C PT5A PT6A PT7A I/O
B6 PT3B PT4B PT4D PT5C PT6C I/O
A5 PT3A PT4A PT4A PT5A PT6A I/O-TDI
D7 PT2D PT3D PT3D PT4D PT5D I/O
C6 PT2C PT3C PT3C PT4A PT5A I/O-VDD5
B5 PT2B PT3B PT3B PT3D PT4D I/O
A4 PT2A PT3A PT3A PT3A PT4A I/O-TMS
C5 — PT2D PT2D PT2D PT3D I/O
B4 PT1D PT2C PT2C PT2C PT3A I/O
A3 PT1C PT2B PT2B PT2B PT2D I/O
D5 PT1B PT2A PT2A PT2A PT2A I/O
C4 — PT1D PT1D PT1D PT1D I/O
B3 — PT1C PT1C PT1C PT1C I/O
B2 — PT1B PT1B PT1B PT1B I/O
A2 PT1A PT1A PT1A PT1A PT1A I/O-TCK
C3 RD_DATA/TDO RD_DATA/TDO RD_DATA/TDO RD_DATA/TDO RD_DATA/TDO RD_DATA/TDO
A1 VSS VSS VSS VSS VSS VSS
D4 VSS VSS VSS VSS VSS VSS
D8 VSS VSS VSS VSS VSS VSS
D13 VSS VSS VSS VSS VSS VSS
D17 VSS VSS VSS VSS VSS VSS
H4 VSS VSS VSS VSS VSS VSS
H17 VSS VSS VSS VSS VSS VSS
N4 VSS VSS VSS VSS VSS VSS
N17 VSS VSS VSS VSS VSS VSS
U4 VSS VSS VSS VSS VSS VSS
Pin Information (continued)
Table 25. OR2C/2T06A, OR2C/2T08A, OR2C/2T10A, OR2C/2T12A, and OR2C/2T15A/B
256-Pin PBGA Pinout (continued)
Pin 2C/2T06A Pad 2C/2T08A Pad 2C/2T10A Pad 2C/2T12A Pad 2C/2T15A/B Pad Function
Notes:
The W3 pin on the 256-pin PBGA package is unconnected for all devices listed in this table.
The OR2C/2T08A do not have bond pads connected to the 256-pin PBGA package pins F2 and Y17.
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, b ut they are connected to VDD5 f or the OR2TxxA series.
The pins labeled VSS-ETC are the 4 x 4 array of thermal balls located at the center of the package. The balls can be attached to the ground
plane of the board for enhanced thermal capability (see Table 29) , or they can be left unconnected.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
98 Lucent Technologies Inc.
U8 VSS VSS VSS VSS VSS VSS
U13 VSS VSS VSS VSS VSS VSS
U17 VSS VSS VSS VSS VSS VSS
B1 VDD VDD VDD VDD VDD VDD
D6 VDD VDD VDD VDD VDD VDD
D11 VDD VDD VDD VDD VDD VDD
D15 VDD VDD VDD VDD VDD VDD
F4 VDD VDD VDD VDD VDD VDD
F17 VDD VDD VDD VDD VDD VDD
K4 VDD VDD VDD VDD VDD VDD
L17 VDD VDD VDD VDD VDD VDD
R4 VDD VDD VDD VDD VDD VDD
R17 VDD VDD VDD VDD VDD VDD
U6 VDD VDD VDD VDD VDD VDD
U10 VDD VDD VDD VDD VDD VDD
U15 VDD VDD VDD VDD VDD VDD
W3 — — — — — No Connect
J10 VSS VSS VSS VSS VSS VSS—ETC
J11 VSS VSS VSS VSS VSS VSS—ETC
J12 VSS VSS VSS VSS VSS VSS—ETC
J9 VSS VSS VSS VSS VSS VSS—ETC
K10 VSS VSS VSS VSS VSS VSS—ETC
K11 VSS VSS VSS VSS VSS VSS—ETC
K12 VSS VSS VSS VSS VSS VSS—ETC
K9 VSS VSS VSS VSS VSS VSS—ETC
L10 VSS VSS VSS VSS VSS VSS—ETC
L11 VSS VSS VSS VSS VSS VSS—ETC
L12 VSS VSS VSS VSS VSS VSS—ETC
L9 VSS VSS VSS VSS VSS VSS—ETC
M10 VSS VSS VSS VSS VSS VSS—ETC
M11 VSS VSS VSS VSS VSS VSS—ETC
M12 VSS VSS VSS VSS VSS VSS—ETC
M9 VSS VSS VSS VSS VSS VSS—ETC
Pin Information (continued)
Table 25. OR2C/2T06A, OR2C/2T08A, OR2C/2T10A, OR2C/2T12A, and OR2C/2T15A/B
256-Pin PBGA Pinout (continued)
Pin 2C/2T06A Pad 2C/2T08A Pad 2C/2T10A Pad 2C/2T12A Pad 2 C/2T15A/B Pad Function
Notes:
The W3 pin on the 256-pin PBGA package is unconnected for all devices listed in this table.
The OR2C/2T08A do not have bond pads connected to the 256-pin PBGA package pins F2 and Y17.
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, b ut they are connected to VDD5 f or the OR2TxxA series.
The pins labeled VSS-ETC are the 4 x 4 array of thermal balls located at the center of the package. The balls can be attached to the ground
plane of the board for enhanced thermal capability (see Table 29) , or they can be left unconnected.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 99
Pin Information (continued)
Table 26. OR2C12A, OR2C15A, OR2C26A, and OR2C40A 304-Pin SQFP/SQFP2 Pinout
Pin 2C 12A Pad 2C15A Pad 2C26A Pad 2 C40A Pad Function
1V
SS VSS VSS VSS VSS
2V
DD VDD VDD VDD VDD
3V
SS VSS VSS VSS VSS
4 PL1D PL1D PL1D PL1D I/O
5 PL1C PL1C PL1C PL1A I/O
6 PL1B PL1B PL1B PL2D I/O
7 PL1A PL1A PL1A PL2A I/O
8 PL2D PL2D PL2D PL3D I/O-A0
9 PL2C PL2A PL2A PL3A I/O
10 PL2B PL3D PL3D PL4D I/O
11 PL2A PL3A PL3A PL4A I/O
12 VSS VSS VSS VSS VSS
13 PL3D PL4D PL4D PL5D I/O
14 PL3A PL4A PL4A PL6D I/O
15 PL4D PL5D PL5D PL7D I/O
16 PL4A PL5A PL5A PL8D I/O-A1
17 PL5D PL6D PL6D PL9D I/O
18 PL5C PL6C PL6C PL9C I/O
19 PL5B PL6B PL6B PL9B I/O
20 PL5A PL6A PL6A PL9A I/O-A2
21 PL6D PL7D PL7D PL10D I/O
22 PL6C PL7C PL7C PL10C I/O
23 PL6B PL7B PL7B PL10B I/O
24 PL6A PL7A PL7A PL10A I/O-A3
25 VDD VDD VDD VDD VDD
26 PL7D PL8D PL8D PL11D I/O
27 PL7C PL8C PL8A PL11A I/O
28 PL7B PL8B PL9D PL12D I/O
29 PL7A PL8A PL9A PL12A I/O-A4
30 PL8D PL9D PL10D PL13D I/O-A5
31 PL8C PL9C PL10A PL13A I/O
32 PL8B PL9B PL11D PL14D I/O
33 PL8A PL9A PL11A PL14A I/O-A6
34 VSS VSS VSS VSS VSS
35 PL9D PL10D PL12D PL15D I/O
36 PL9C PL10C PL12C PL15C I/O
37 PL9B PL10B PL12B PL15B I/O
38 PL9A PL10A PL12A PL15A I/O-A7
39 VDD VDD VDD VDD VDD
40 PL10D PL11D PL13D PL16D I/O
41 PL10C PL11C PL13C PL16C I/O
42 PL10B PL11B PL13B PL16B I/O
43 PL10A PL11A PL13A PL16A I/O-A8
44 VSS VSS VSS VSS VSS
Note: The OR2TxxA and OR2TxxB series are not off ered in the 304-pin SQFP/SQFP2 packages.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
100 Lucent Technologies Inc.
45 PL11D PL12D PL14D PL17D I/O-A9
46 PL11C PL12C PL14A PL17A I/O
47 PL11B PL12B PL15D PL18D I/O
48 PL11A PL12A PL15A PL18A I/O-A10
49 PL12D PL13D PL16D PL19D I/O
50 PL12C PL13C PL16A PL19A I/O
51 PL12B PL13B PL17D PL20D I/O
52 PL12A PL13A PL17A PL20A I/O-A11
53 VDD VDD VDD VDD VDD
54 PL13D PL14D PL18D PL21D I/O-A12
55 PL13B PL14B PL18B PL21B I/O
56 PL13A PL14A PL18A PL21A I/O
57 PL14D PL15D PL19D PL22D I/O
58 PL14B PL15B PL19B PL22B I/O-A13
59 PL14A PL15A PL19A PL22A I/O
60 PL15D PL16D PL20D PL23D I/O
61 PL15B PL16B PL20B PL24D I/O
62 PL15A PL16A PL20A PL25D I/O
63 PL16D PL17D PL21D PL25A I/O-A14
64 PL16A PL17A PL21A PL26A I/O
65 VSS VSS VSS VSS VSS
66 PL17D PL18D PL22D PL27D I/O
67 PL17C PL18C PL22C PL27C I/O
68 PL17B PL18A PL22A PL27A I/O
69 PL17A PL19D PL23D PL28D I/O
70 PL18D PL19C PL23C PL28C I/O
71 PL18C PL19A PL23A PL28A I/O
72 PL18B PL20D PL24D PL29A I/O
73 PL18A PL20A PL24A PL30A I/O-A15
74 VSS VSS VSS VSS VSS
75 CCLK CCLK CCLK CCLK CCLK
76 VDD VDD VDD VDD VDD
77 VSS VSS VSS VSS VSS
78 VDD VDD VDD VDD VDD
79 VSS VSS VSS VSS VSS
80 PB1A PB1A PB1A PB1A I/O-A16
81 PB1B PB1C PB1C PB2A I/O
82 PB1C PB1D PB1D PB2D I/O
83 PB1D PB2A PB2A PB3A I/O
84 PB2A PB2D PB2D PB3D I/O
85 PB2B PB3A PB3A PB4A I/O
86 PB2C PB3C PB3C PB4C I/O
87 PB2D PB3D PB3D PB4D I/O
88 VSS VSS VSS VSS VSS
89 PB3A PB4A PB4A PB5A I/O
Pin Information (continued)
Table 26. OR2C12A, OR2C15A, OR2C26A, and OR2C40A 304-Pin SQFP/SQFP2 Pinout (continued)
Pin 2C 12A Pad 2C15A Pad 2C26A Pad 2 C40A Pad Function
Note: The OR2TxxA and OR2TxxB series are not offered in the 304-pin SQFP/SQFP2 packages.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 101
90 PB3D PB4D PB4D PB5D I/O-A17
91 PB4A PB5A PB5A PB6A I/O
92 PB4D PB5D PB5D PB6D I/O
93 PB5A PB6A PB6A PB7A I/O
94 PB5B PB6B PB6B PB7D I/O
95 PB5C PB6C PB6C PB8A I/O
96 PB5D PB6D PB6D PB8D I/O
97 PB6A PB7A PB7A PB9A I/O
98 PB6B PB7B PB7B PB9D I/O
99 PB6C PB7C PB7C PB10A I/O
100 PB6D PB7D PB7D PB10D I/O
101 VDD VDD VDD VDD VDD
102 PB7A PB8A PB8A PB11A I/O
103 PB7B PB8B PB8D PB11D I/O
104 PB7C PB8C PB9A PB12A I/O
105 PB7D PB8D PB9D PB12D I/O
106 PB8A PB9A PB10A PB13A I/O
107 PB8B PB9B PB10D PB13D I/O
108 PB8C PB9C PB11A PB14A I/O
109 PB8D PB9D PB11D PB14D I/O
110 VSS VSS VSS VSS VSS
111 PB9A PB10A PB12A PB15A I/O
112 PB9B PB10B PB12B PB15B I/O
113 PB9C PB10C PB12C PB15C I/O
114 PB9D PB10D PB12D PB15D I/O
115 VSS VSS VSS VSS VSS
116 PB10A PB11A PB13A PB16A I/O
117 PB10B PB11B PB13B PB16B I/O
118 PB10C PB11C PB13C PB16C I/O
119 PB10D PB11D PB13D PB16D I/O
120 VSS VSS VSS VSS VSS
121 PB11A PB12A PB14A PB17A I/O
122 PB11B PB12B PB14D PB17D I/O
123 PB11C PB12C PB15A PB18A I/O
124 PB11D PB12D PB15D PB18D I/O
125 PB12A PB13A PB16A PB19A I/O-HDC
126 PB12B PB13B PB16D PB19D I/O
127 PB12C PB13C PB17A PB20A I/O
128 PB12D PB13D PB17D PB20D I/O
129 VDD VDD VDD VDD VDD
130 PB13A PB14A PB18A PB21A I/O-LDC
131 PB13B PB14B PB18B PB21D I/O
132 PB13C PB14C PB18C PB22A I/O
133 PB13D PB14D PB18D PB22D I/O
134 PB14A PB15A PB19A PB23A I/O
Pin Information (continued)
Table 26. OR2C12A, OR2C15A, OR2C26A, and OR2C40A 304-Pin SQFP/SQFP2 Pinout (continued)
Pin 2C 12A Pad 2C15A Pad 2C26A Pad 2 C40A Pad Function
Note: The OR2TxxA and OR2TxxB series are not off ered in the 304-pin SQFP/SQFP2 packages.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
102 Lucent Technologies Inc.
135 PB14B PB15B PB19B PB24A I/O
136 PB14D PB15D PB19D PB24D I/O
137 PB15A PB16A PB20A PB25A I/O-INIT
138 PB15D PB16D PB20D PB25D I/O
139 PB16A PB17A PB21A PB26A I/O
140 PB16D PB17D PB21D PB26D I/O
141 VSS VSS VSS VSS VSS
142 PB17A PB18A PB22A PB27A I/O
143 PB17B PB18B PB22B PB27B I/O
144 PB17C PB18D PB22D PB27D I/O
145 PB17D PB19A PB23A PB28A I/O
146 PB18A PB19D PB23D PB28D I/O
147 PB18B PB20A PB24A PB29A I/O
148 PB18C PB20B PB24B PB29D I/O
149 PB18D PB20D PB24D PB30D I/O
150 VSS VSS VSS VSS VSS
151 DONE DONE DONE DONE DONE
152 VDD VDD VDD VDD VDD
153 VSS VSS VSS VSS VSS
154 RESET RESET RESET RESET RESET
155 PRGM PRGM PRGM PRGM PRGM
156 PR18A PR20A PR24A PR30A I/O-M0
157 PR18B PR20C PR24C PR29A I/O
158 PR18C PR20D PR24D PR29D I/O
159 PR18D PR19A PR23A PR28A I/O
160 PR17A PR19D PR23D PR28D I/O
161 PR17B PR18A PR22A PR27A I/O
162 PR17C PR18B PR22B PR27B I/O
163 PR17D PR18D PR22D PR27D I/O
164 VSS VSS VSS VSS VSS
165 PR16A PR17A PR21A PR26A I/O
166 PR16D PR17D PR21D PR25A I/O
167 PR15A PR16A PR20A PR24A I/O
168 PR15C PR16C PR20C PR24D I/O
169 PR15D PR16D PR20D PR23D I/O-M1
170 PR14A PR15A PR19A PR22A I/O
171 PR14C PR15C PR19C PR22C I/O
172 PR14D PR15D PR19D PR22D I/O
173 PR13A PR14A PR18A PR21A I/O
174 PR13C PR14C PR18C PR21C I/O
175 PR13D PR14D PR18D PR21D I/O
176 VDD VDD VDD VDD VDD
177 PR12A PR13A PR17A PR20A I/O-M2
178 PR12B PR13B PR17D PR20D I/O
179 PR12C PR13C PR16A PR19A I/O
Pin Information (continued)
Table 26. OR2C12A, OR2C15A, OR2C26A, and OR2C40A 304-Pin SQFP/SQFP2 Pinout (continued)
Pin 2C 12A Pad 2C15A Pad 2C26A Pad 2 C40A Pad Function
Note: The OR2TxxA and OR2TxxB series are not offered in the 304-pin SQFP/SQFP2 packages.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 103
180 PR12D PR13D PR16D PR19D I/O
181 PR11A PR12A PR15A PR18A I/O-M3
182 PR11B PR12B PR15D PR18D I/O
183 PR11C PR12C PR14A PR17A I/O
184 PR11D PR12D PR14D PR17D I/O
185 VSS VSS VSS VSS VSS
186 PR10A PR11A PR13A PR16A I/O
187 PR10B PR11B PR13B PR16B I/O
188 PR10C PR11C PR13C PR16C I/O
189 PR10D PR11D PR13D PR16D I/O
190 VDD VDD VDD VDD VDD
191 PR9A PR10A PR12A PR15A I/O
192 PR9B PR10B PR12B PR15B I/O
193 PR9C PR10C PR12C PR15C I/O
194 PR9D PR10D PR12D PR15D I/O
195 VSS VSS VSS VSS VSS
196 PR8A PR9A PR11A PR14A I/O
197 PR8B PR9B PR11D PR14D I/O
198 PR8C PR9C PR10A PR13A I/O
199 PR8D PR9D PR10D PR13D I/O
200 PR7A PR8A PR9A PR12A I/O-CS1
201 PR7B PR8B PR9D PR12D I/O
202 PR7C PR8C PR8A PR11A I/O
203 PR7D PR8D PR8D PR11D I/O
204 VDD VDD VDD VDD VDD
205 PR6A PR7A PR7A PR10A I/O-CS0
206 PR6B PR7B PR7B PR10B I/O
207 PR6C PR7C PR7C PR10C I/O
208 PR6D PR7D PR7D PR10D I/O
209 PR5A PR6A PR6A PR9A I/O
210 PR5B PR6B PR6B PR9B I/O
211 PR5C PR6C PR6C PR9C I/O
212 PR5D PR6D PR6D PR9D I/O
213 PR4A PR5A PR5A PR8A I/O-RD
214 PR4B PR5B PR5B PR7A I/O
215 PR4D PR5D PR5D PR6A I/O
216 PR3A PR4A PR4A PR5A I/O
217 VSS VSS VSS VSS VSS
218 PR2A PR3A PR3A PR4A I/O-WR
219 PR2B PR3B PR3B PR4B I/O
220 PR2C PR2A PR2A PR3A I/O
221 PR2D PR2D PR2D PR3D I/O
222 PR1A PR1A PR1A PR2A I/O
223 PR1B PR1B PR1B PR2D I/O
224 PR1C PR1C PR1C PR1A I/O
Pin Information (continued)
Table 26. OR2C12A, OR2C15A, OR2C26A, and OR2C40A 304-Pin SQFP/SQFP2 Pinout (continued)
Pin 2C 12A Pad 2C15A Pad 2C26A Pad 2 C40A Pad Function
Note: The OR2TxxA and OR2TxxB series are not off ered in the 304-pin SQFP/SQFP2 packages.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
104 Lucent Technologies Inc.
225 PR1D PR1D PR1D PR1D I/O
226 VSS VSS VSS VSS VSS
227 RD_CFGN RD_CFGN RD_CFGN RD_CFGN RD_CFGN
228 VDD VDD VDD VDD VDD
229 VSS VSS VSS VSS VSS
230 VDD VDD VDD VDD VDD
231 VSS VSS VSS VSS VSS
232 PT18D PT20D PT24D PT30D I/O
233 PT18C PT20C PT24C PT30A I/O
234 PT18B PT20A PT24A PT29A I/O
235 PT18A PT19D PT23D PT28D I/O
236 PT17D PT19A PT23A PT28A I/O-RDY/RCLK
237 PT17C PT18D PT22D PT27D I/O
238 PT17B PT18C PT22C PT27C I/O
239 PT17A PT18A PT22A PT27A I/O
240 VSS VSS VSS VSS VSS
241 PT16D PT17D PT21D PT26D I/O
242 PT16C PT17C PT21C PT26C I/O
243 PT16A PT17A PT21A PT26A I/O
244 PT15D PT16D PT20D PT25D I/O-D7
245 PT15A PT16A PT20A PT25A I/O
246 PT14D PT15D PT19D PT24D I/O
247 PT14A PT15A PT19A PT23D I/O
248 PT13D PT14D PT18D PT22D I/O
249 PT13C PT14C PT18C PT22A I/O
250 PT13B PT14B PT18B PT21D I/O-D6
251 PT13A PT14A PT18A PT21A I/O
252 VDD VDD VDD VDD VDD
253 PT12D PT13D PT17D PT20D I/O
254 PT12C PT13C PT17A PT20A I/O
255 PT12B PT13B PT16D PT19D I/O
256 PT12A PT13A PT16A PT19A I/O-D5
257 PT11D PT12D PT15D PT18D I/O
258 PT11C PT12C PT15A PT18A I/O
259 PT11B PT12B PT14D PT17D I/O
260 PT11A PT12A PT14A PT17A I/O-D4
261 VSS VSS VSS VSS VSS
262 PT10D PT11D PT13D PT16D I/O
263 PT10C PT11C PT13C PT16C I/O
264 PT10B PT11B PT13B PT16B I/O
265 PT10A PT11A PT13A PT16A I/O-D3
266 VSS VSS VSS VSS VSS
267 PT9D PT10D PT12D PT15D I/O
268 PT9C PT10C PT12C PT15C I/O
269 PT9B PT10B PT12B PT15B I/O
Pin Information (continued)
Table 26. OR2C12A, OR2C15A, OR2C26A, and OR2C40A 304-Pin SQFP/SQFP2 Pinout (continued)
Pin 2C 12A Pad 2C15A Pad 2C26A Pad 2 C40A Pad Function
Note: The OR2TxxA and OR2TxxB series are not offered in the 304-pin SQFP/SQFP2 packages.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 105
270 PT9A PT10A PT12A PT15A I/O-D2
271 VSS VSS VSS VSS VSS
272 PT8D PT9D PT11D PT14D I/O-D1
273 PT8C PT9C PT11A PT14A I/O
274 PT8B PT9B PT10D PT13D I/O
275 PT8A PT9A PT10A PT13A I/O-D0/DIN
276 PT7D PT8D PT9D PT12D I/O
277 PT7C PT8C PT9A PT12A I/O
278 PT7B PT8B PT8D PT11D I/O
279 PT7A PT8A PT8A PT11A I/O-DOUT
280 VDD VDD VDD VDD VDD
281 PT6D PT7D PT7D PT10D I/O
282 PT6C PT7C PT7C PT10A I/O
283 PT6B PT7B PT7B PT9D I/O
284 PT6A PT7A PT7A PT9A I/O
285 PT5D PT6D PT6D PT8D I/O
286 PT5C PT6C PT6C PT8A I/O
287 PT5B PT6B PT6B PT7D I/O
288 PT5A PT6A PT6A PT7A I/O-TDI
289 PT4D PT5D PT5D PT6D I/O
290 PT4A PT5A PT5A PT6A I/O
291 PT3D PT4D PT4D PT5D I/O
292 PT3A PT4A PT4A PT5A I/O-TMS
293 VSS VSS VSS VSS VSS
294 PT2D PT3D PT3D PT4D I/O
295 PT2C PT3A PT3A PT4A I/O
296 PT2B PT2D PT2D PT3D I/O
297 PT2A PT2A PT2A PT3A I/O
298 PT1D PT1D PT1D PT2D I/O
299 PT1C PT1C PT1C PT2A I/O
300 PT1B PT1B PT1B PT1D I/O
301 PT1A PT1A PT1A PT1A I/O-TCK
302 VSS VSS VSS VSS VSS
303 RD_DATA/TDO RD_DATA/TDO RD_DATA/TDO RD_DATA/TDO RD_DATA/TDO
304 VDD VDD VDD VDD VDD
Pin Information (continued)
Table 26. OR2C12A, OR2C15A, OR2C26A, and OR2C40A 304-Pin SQFP/SQFP2 Pinout (continued)
Pin 2C 12A Pad 2C15A Pad 2C26A Pad 2 C40A Pad Function
Note: The OR2TxxA and OR2TxxB series are not off ered in the 304-pin SQFP/SQFP2 packages.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
106 Lucent Technologies Inc.
Pin Information (continued)
Table 27. OR2C/2T10A, OR2C/2T12A, OR2C/2T15A/B, OR2C/2T26A, and OR2T40A/B 352-Pin PBGA
Pinout
Pin 2C/2T10A Pad 2C/2T12A Pad 2C/2T15A/B Pad 2C/2T26A Pad OR2T40A/B Pad Function
B1 PL1D PL1D PL1D PL1D PL1D I/O
C2 PL1C PL1C PL1C PL1C PL1A I/O
C1 PL1B PL1B PL1B PL1B PL2D I/O
D2 PL1A PL1A PL1A PL1A PL2A I/O
D3 PL2D PL2D PL2D PL2D PL3D I/O-A0
D1 PL2C PL2C PL2A PL2A PL3A I/O
E2 PL2B PL2B PL3D PL3D PL4D I/O
E4 — — PL3B PL3B PL4B I/O
E3 PL2A PL2A PL3A PL3A PL4A I/O
E1 PL3D PL3D PL4D PL4D VDD5 I/O-VDD5
F2 — PL3C PL4C PL4C PL5C I/O
G4 PL3C PL3B PL4B PL4B PL5B I/O
F3 — PL3A PL4A PL4A PL6D I/O
F1 PL3B PL4D PL5D PL5D PL7D I/O
G2 — PL4C PL5C PL5C PL7C I/O
G1 — PL4B PL5B PL5B PL7B I/O
G3 PL3A PL4A PL5A PL5A PL8D I/O-A1
H2 PL4D PL5D PL6D PL6D PL9D I/O
J4 PL4C PL5C PL6C PL6C PL9C I/O
H1 PL4B PL5B PL6B PL6B PL9B I/O
H3 PL4A PL5A PL6A PL6A PL9A I/O-A2
J2 PL5D PL6D PL7D PL7D PL10D I/O
J1 PL5C PL6C PL7C PL7C PL10C I/O
K2 PL5B PL6B PL7B PL7B PL10B I/O
J3 PL5A PL6A PL7A PL7A PL10A I/O-A3
K1 PL6D PL7D PL8D PL8D PL11D I/O
K4 PL6C PL7C PL8C PL8A PL11A I/O
L2 PL6B PL7B PL8B PL9D PL12D I/O
K3 PL6A PL7A PL8A PL9A PL12A I/O-A4
L1 PL7D PL8D PL9D PL10D PL13D I/O-A5
M2 PL7C PL8C PL9C PL10A PL13A I/O
M1 PL7B PL8B PL9B PL11D PL14D I/O
L3 PL7A PL8A PL9A PL11A PL14A I/O-A6
N2 PL8D PL9D PL10D PL12D PL15D I/O
M4 PL8C PL9C PL10C PL12C PL15C I/O
N1 PL8B PL9B PL10B PL12B PL15B I/O
M3 PL8A PL9A PL10A PL12A PL15A I/O-A7
P2 PL9D PL10D PL11D PL13D PL16D I/O
Notes:
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, but they are connected to VDD5 for the OR2TxxA series.
The pins labeled VSS-ETC are the 6 x 6 arra y of thermal balls located at the center of the package. The balls can be attached to the ground plane
of the board for enhanced ther mal capability (see Table 29), or they can be left unconnected.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 107
P4 PL9C PL10C PL11C PL13C VDD5 I/O-VDD5
P1 PL9B PL10B PL11B PL13B PL16B I/O
N3 PL9A PL10A PL11A PL13A PL16A I/O-A8
R2 PL10D PL11D PL12D PL14D PL17D I/O-A9
P3 PL10C PL11C PL12C PL14A PL17A I/O
R1 PL10B PL11B PL12B PL15D PL18D I/O
T2 PL10A PL11A PL12A PL15A PL18A I/O-A10
R3 PL11D PL12D PL13D PL16D PL19D I/O
T1 PL11C PL12C PL13C PL16A PL19A I/O
R4 PL11B PL12B PL13B PL17D PL20D I/O
U2 PL11A PL12A PL13A PL17A PL20A I/O-A11
T3 PL12D PL13D PL14D PL18D PL21D I/O-A12
U1 — PL13C PL14C PL18C PL21C I/O
U4 PL12C PL13B PL14B PL18B PL21B I/O
V2 — PL13A PL14A PL18A PL21A I/O
U3 PL12B PL14D PL15D PL19D PL22D I/O
V1 PL12A PL14C PL15C PL19C PL22C I/O
W2 PL13D PL14B PL15B PL19B PL22B I/O-A13
W1 PL13C PL14A PL15A PL19A PL22A I/O
V3 PL13B PL15D PL16D PL20D PL23D I/O
Y2 PL13A PL15C PL16C PL20C PL23C I/O
W4 PL14D PL15B PL16B PL20B PL24D I/O
Y1 — PL15A PL16A PL20A PL25D I/O
W3 PL14C PL16D PL17D PL21D PL25A I/O-A14
AA2 PL14B PL16C PL17C PL21C PL26C I/O
Y4 PL14A PL16B PL17B PL21B PL26B I/O
AA1 — PL16A PL17A PL21A PL26A I/O
Y3 PL15D PL17D PL18D PL22D VDD5 I/O-VDD5
AB2 PL15C PL17C PL18C PL22C PL27C I/O
AB1 PL15B PL17B PL18A PL22A PL27A I/O
AA3 PL15A PL17A PL19D PL23D PL28D I/O
AC2 PL16D PL18D PL19C PL23C PL28C I/O
AB4 PL16C PL18C PL19A PL23A PL28A I/O
AC1 PL16B PL18B PL20D PL24D PL29A I/O
AB3 — — PL20C PL24C PL30C I/O
AD2 — — PL20B PL24B PL30B I/O
AC3 PL16A PL18A PL20A PL24A PL30A I/O-A15
AD1 CCLK CCLK CCLK CCLK PCCLK CCLK
AF2 PB1A PB1A PB1A PB1A PB1A I/O-A16
Pin Information (continued)
Table 27. OR2C/2T10A, OR2C/2T12A, OR2C/2T15A/B, OR2C/2T26A, and OR2T40A/B 352-Pin PBGA
Pinout (conti nued)
Pin 2C/2T10A Pad 2C/2T12A Pad 2C/2T15A/B Pad 2C/2T26A Pad OR2T40A/B Pad Function
Notes:
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB ser ies, but they are connected to VDD5 for the OR2TxxA series.
The pins labeled VSS-ETC are the 6 x 6 arra y of thermal balls located at the center of the package . The balls can be attached to the ground plane
of the board for enhanced ther mal capability (see Table 29), or they can be left unconnected.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
108 Lucent Technologies Inc.
AE3 — — PB1B PB1B PB1B I/O
AF3 PB1B PB1B PB1C PB1C PB2A I/O
AE4 PB1C PB1C PB1D PB1D PB2D I/O
AD4 PB1D PB1D PB2A PB2A PB3A I/O
AF4 PB2A PB2A PB2D PB2D VDD5 I/O-VDD5
AE5 — PB2B PB3A PB3A PB4A I/O
AC5 PB2B PB2C PB3C PB3C PB4C I/O
AD5 — PB2D PB3D PB3D PB4D I/O
AF5 PB2C PB3A PB4A PB4A PB5A I/O
AE6 PB2D PB3B PB4B PB4B PB5B I/O
AC7 PB3A PB3C PB4C PB4C PB5C I/O
AD6 PB3B PB3D PB4D PB4D PB5D I/O-A17
AF6 — PB4A PB5A PB5A PB6A I/O
AE7 PB3C PB4B PB5B PB5B PB6B I/O
AF7 — PB4C PB5C PB5C PB6C I/O
AD7 PB3D PB4D PB5D PB5D PB6D I/O
AE8 PB4A PB5A PB6A PB6A PB7A I/O
AC9 PB4B PB5B PB6B PB6B PB7D I/O
AF8 PB4C PB5C PB6C PB6C PB8A I/O
AD8 PB4D PB5D PB6D PB6D PB8D I/O
AE9 PB5A PB6A PB7A PB7A PB9A I/O
AF9 PB5B PB6B PB7B PB7B PB9D I/O
AE10 PB5C PB6C PB7C PB7C PB10A I/O
AD9 PB5D PB6D PB7D PB7D PB10D I/O
AF10 PB6A PB7A PB8A PB8A PB11A I/O
AC10 PB6B PB7B PB8B PB8D PB11D I/O
AE11 PB6C PB7C PB8C PB9A PB12A I/O
AD10 PB6D PB7D PB8D PB9D PB12D I/O
AF11 PB7A PB8A PB9A PB10A PB13A I/O
AE12 PB7B PB8B PB9B PB10D PB13D I/O
AF12 PB7C PB8C PB9C PB11A PB14A I/O
AD11 PB7D PB8D PB9D PB11D PB14D I/O
AE13 PB8A PB9A PB10A PB12A PB15A I/O
AC12 PB8B PB9B PB10B PB12B PB15B I/O
AF13 PB8C PB9C PB10C PB12C PB15C I/O
AD12 PB8D PB9D PB10D PB12D PB15D I/O
AE14 PB9A PB10A PB11A PB13A PB16A I/O
AC14 PB9B PB10B PB11B PB13B PB16B I/O
AF14 PB9C PB10C PB11C PB13C PB16C I/O
Pin Information (continued)
Table 27. OR2C/2T10A, OR2C/2T12A, OR2C/2T15A/B, OR2C/2T26A, and OR2T40A/B 352-Pin PBGA
Pinout (conti nued)
Pin 2C/2T10A Pad 2C/2T12A Pad 2C/2T15A/B Pad 2C/2T26A Pad OR2T40A/B Pad Function
Notes:
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, but they are connected to VDD5 for the OR2TxxA series.
The pins labeled VSS-ETC are the 6 x 6 arra y of thermal balls located at the center of the package. The balls can be attached to the ground plane
of the board for enhanced ther mal capability (see Table 29), or they can be left unconnected.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 109
AD13 PB9D PB10D PB11D PB13D PB16D I/O
AE15 PB10A PB11A PB12A PB14A VDD5 I/O-VDD5
AD14 PB10B PB11B PB12B PB14D PB17D I/O
AF15 PB10C PB11C PB12C PB15A PB18A I/O
AE16 PB10D PB11D PB12D PB15D PB18D I/O
AD15 PB11A PB12A PB13A PB16A PB19A I/O-HDC
AF16 PB11B PB12B PB13B PB16D PB19D I/O
AC15 PB11C PB12C PB13C PB17A PB20A I/O
AE17 PB11D PB12D PB13D PB17D PB20D I/O
AD16 PB12A PB13A PB14A PB18A PB21A I/O-LDC
AF17 PB12B PB13B PB14B PB18B PB21D I/O
AC17 PB12C PB13C PB14C PB18C PB22A I/O
AE18 PB12D PB13D PB14D PB18D PB22D I/O
AD17 PB13A PB14A PB15A PB19A PB23A I/O
AF18 PB13B PB14B PB15B PB19B PB24A I/O
AE19 — PB14C PB15C PB19C PB24C I/O
AF19 PB13C PB14D PB15D PB19D PB24D I/O
AD18 PB13D PB15A PB16A PB20A PB25A I/O-INIT
AE20 — PB15B PB16B PB20B PB25B I/O
AC19 PB14A PB15C PB16C PB20C PB25C I/O
AF20 — PB15D PB16D PB20D PB25D I/O
AD19 PB14B PB16A PB17A PB21A VDD5 I/O-VDD5
AE21 PB14C PB16B PB17B PB21B PB26B I/O
AC20 PB14D PB16C PB17C PB21C PB26C I/O
AF21 PB15A PB16D PB17D PB21D PB26D I/O
AD20 PB15B PB17A PB18A PB22A PB27A I/O
AE22 PB15C PB17B PB18B PB22B PB27B I/O
AF22 PB15D PB17C PB18D PB22D PB27D I/O
AD21 PB16A PB17D PB19A PB23A PB28A I/O
AE23 — — PB19C PB23B PB28B I/O
AC22 PB16B PB18A PB19D PB23D PB28D I/O
AF23 PB16C PB18B PB20A PB24A PB29A I/O
AD22 PB16D PB18C PB20B PB24B PB29D I/O
AE24 — — PB20C PB24C PB30C I/O
AD23 — PB18D PB20D PB24D PB30D I/O
AF24 DONE DONE DONE DONE PDONE DONE
AE26 RESET RESET RESET RESET PRESETN RESET
AD25 PRGM PRGM PRGM PRGM PPRGMN PRGM
AD26 PR16A PR18A PR20A PR24A PR30A I/O-M0
Pin Information (continued)
Table 27. OR2C/2T10A, OR2C/2T12A, OR2C/2T15A/B, OR2C/2T26A, and OR2T40A/B 352-Pin PBGA
Pinout (conti nued)
Pin 2C/2T10A Pad 2C/2T12A Pad 2C/2T15A/B Pad 2C/2T26A Pad OR2T40A/B Pad Function
Notes:
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB ser ies, but they are connected to VDD5 for the OR2TxxA series.
The pins labeled VSS-ETC are the 6 x 6 arra y of thermal balls located at the center of the package . The balls can be attached to the ground plane
of the board for enhanced ther mal capability (see Table 29), or they can be left unconnected.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
110 Lucent Technologies Inc.
AC25 PR16B PR18B PR20C PR24C PR29A I/O
AC24 PR16C PR18C PR20D PR24D PR29D I/O
AC26 PR16D PR18D PR19A PR23A PR28A I/O
AB25 PR15A PR17A PR19D PR23D PR28D I/O
AB23 PR15B PR17B PR18A PR22A PR27A I/O
AB24 PR15C PR17C PR18B PR22B PR27B I/O
AB26 PR15D PR17D PR18D PR22D PR27D I/O
AA25 PR14A PR16A PR17A PR21A PR26A I/O
Y23 PR14B PR16B PR17B PR21B PR26B I/O
AA24 PR14C PR16C PR17C PR21C PR26C I/O
AA26 — PR16D PR17D PR21D PR25A I/O
Y25 PR14D PR15A PR16A PR20A PR24A I/O
Y26 — PR15B PR16B PR20B PR24B I/O
Y24 PR13A PR15C PR16C PR20C PR24D I/O
W25 PR13B PR15D PR16D PR20D PR23D I/O-M1
V23 PR13C PR14A PR15A PR19A PR22A I/O
W26 — PR14B PR15B PR19B PR22B I/O
W24 PR13D PR14C PR15C PR19C PR22C I/O
V25 PR12A PR14D PR15D PR19D VDD5 I/O-VDD5
V26 PR12B PR13A PR14A PR18A PR21A I/O
U25 — PR13B PR14B PR18B PR21B I/O
V24 PR12C PR13C PR14C PR18C PR21C I/O
U26 PR12D PR13D PR14D PR18D PR21D I/O
U23 PR11A PR12A PR13A PR17A PR20A I/O-M2
T25 PR11B PR12B PR13B PR17D PR20D I/O
U24 PR11C PR12C PR13C PR16A PR19A I/O
T26 PR11D PR12D PR13D PR16D PR19D I/O
R25 PR10A PR11A PR12A PR15A PR18A I/O-M3
R26 PR10B PR11B PR12B PR15D PR18D I/O
T24 PR10C PR11C PR12C PR14A PR17A I/O
P25 PR10D PR11D PR12D PR14D PR17D I/O
R23 PR9A PR10A PR11A PR13A PR16A I/O
P26 PR9B PR10B PR11B PR13B PR16B I/O
R24 PR9C PR10C PR11C PR13C PR16C I/O
N25 PR9D PR10D PR11D PR13D PR16D I/O
N23 PR8A PR9A PR10A PR12A PR15A I/O
N26 PR8B PR9B PR10B PR12B PR15B I/O
P24 PR8C PR9C PR10C PR12C PR15C I/O
M25 PR8D PR9D PR10D PR12D PR15D I/O
Pin Information (continued)
Table 27. OR2C/2T10A, OR2C/2T12A, OR2C/2T15A/B, OR2C/2T26A, and OR2T40A/B 352-Pin PBGA
Pinout (conti nued)
Pin 2C/2T10A Pad 2C/2T12A Pad 2C/2T15A/B Pad 2C/2T26A Pad OR2T40A/B Pad Function
Notes:
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, but they are connected to VDD5 for the OR2TxxA series.
The pins labeled VSS-ETC are the 6 x 6 arra y of thermal balls located at the center of the package. The balls can be attached to the ground plane
of the board for enhanced ther mal capability (see Table 29), or they can be left unconnected.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 111
N24 PR7A PR8A PR9A PR11A VDD5 I/O-VDD5
M26 PR7B PR8B PR9B PR11D PR14D I/O
L25 PR7C PR8C PR9C PR10A PR13A I/O
M24 PR7D PR8D PR9D PR10D PR13D I/O
L26 PR6A PR7A PR8A PR9A PR12A I/O-CS1
M23 PR6B PR7B PR8B PR9D PR12D I/O
K25 PR6C PR7C PR8C PR8A PR11A I/O
L24 PR6D PR7D PR8D PR8D PR11D I/O
K26 PR5A PR6A PR7A PR7A PR10A I/O-CS0
K23 PR5B PR6B PR7B PR7B PR10B I/O
J25 PR5C PR6C PR7C PR7C PR10C I/O
K24 PR5D PR6D PR7D PR7D PR10D I/O
J26 PR4A PR5A PR6A PR6A PR9A I/O
H25 PR4B PR5B PR6B PR6B PR9B I/O
H26 PR4C PR5C PR6C PR6C PR9C I/O
J24 PR4D PR5D PR6D PR6D PR9D I/O
G25 PR3A PR4A PR5A PR5A PR8A I/O-RD
H23 PR3B PR4B PR5B PR5B PR7A I/O
G26 — PR4C PR5C PR5C PR7C I/O
H24 PR3C PR4D PR5D PR5D PR6A I/O
F25 PR3D PR3A PR4A PR4A VDD5 I/O-VDD5
G23 — PR3B PR4B PR4B PR5B I/O
F26 — PR3C PR4C PR4C PR5C I/O
G24 — PR3D PR4D PR4D PR5D I/O
E25 PR2A PR2A PR3A PR3A PR4A I/O-WR
E26 PR2B PR2B PR3B PR3B PR4B I/O
F24 — — PR3D PR3D PR4D I/O
D25 PR2C PR2C PR2A PR2A PR3A I/O
E23 PR2D PR2D PR2D PR2D PR3D I/O
D26 PR1A PR1A PR1A PR1A PR2A I/O
E24 PR1B PR1B PR1B PR1B PR2D I/O
C25 PR1C PR1C PR1C PR1C PR1A I/O
D24 PR1D PR1D PR1D PR1D PR1D I/O
C26 RD_CFGN RD_CFGN RD_CFGN RD_CFGN RD_CFGN RD_CFGN
A25 PT16D PT18D PT20D PT24D PT30D I/O
B24 PT16C PT18C PT20C PT24C PT30A I/O
A24 — — PT20B PT24B PT29B I/O
B23 PT16B PT18B PT20A PT24A PT29A I/O
C23 PT16A PT18A PT19D PT23D PT28D I/O
Pin Information (continued)
Table 27. OR2C/2T10A, OR2C/2T12A, OR2C/2T15A/B, OR2C/2T26A, and OR2T40A/B 352-Pin PBGA
Pinout (conti nued)
Pin 2C/2T10A Pad 2C/2T12A Pad 2C/2T15A/B Pad 2C/2T26A Pad OR2T40A/B Pad Function
Notes:
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB ser ies, but they are connected to VDD5 for the OR2TxxA series.
The pins labeled VSS-ETC are the 6 x 6 arra y of thermal balls located at the center of the package . The balls can be attached to the ground plane
of the board for enhanced ther mal capability (see Table 29), or they can be left unconnected.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
112 Lucent Technologies Inc.
A23 PT15D PT17D PT19A PT23A PT28A I/O-RDY/
RCLK
B22 PT15C PT17C PT18D PT22D PT27D I/O
D22 PT15B PT17B PT18C PT22C PT27C I/O
C22 PT15A PT17A PT18A PT22A PT27A I/O
A22 PT14D PT16D PT17D PT21D PT26D I/O
B21 PT14C PT16C PT17C PT21C PT26C I/O
D20 PT14B PT16B PT17B PT21B PT26B I/O
C21 PT14A PT16A PT17A PT21A PT26A I/O
A21 PT13D PT15D PT16D PT20D PT25D I/O-D7
B20 — PT15C PT16C PT20C PT25C I/O
A20 PT13C PT15B PT16B PT20B PT25B I/O
C20 — PT15A PT16A PT20A PT25A I/O
B19 PT13B PT14D PT15D PT19D VDD5 I/O-VDD5
D18 — PT14C PT15C PT19C PT24C I/O
A19 PT13A PT14B PT15B PT19B PT24B I/O
C19 — PT14A PT15A PT19A PT23D I/O
B18 PT12D PT13D PT14D PT18D PT22D I/O
A18 PT12C PT13C PT14C PT18C PT22A I/O
B17 PT12B PT13B PT14B PT18B PT21D I/O-D6
C18 PT12A PT13A PT14A PT18A PT21A I/O
A17 PT11D PT12D PT13D PT17D PT20D I/O
D17 PT11C PT12C PT13C PT17A PT20A I/O
B16 PT11B PT12B PT13B PT16D PT19D I/O
C17 PT11A PT12A PT13A PT16A PT19A I/O-D5
A16 PT10D PT11D PT12D PT15D PT18D I/O
B15 PT10C PT11C PT12C PT15A PT18A I/O
A15 PT10B PT11B PT12B PT14D PT17D I/O
C16 PT10A PT11A PT12A PT14A PT17A I/O-D4
B14 PT9D PT10D PT11D PT13D PT16D I/O
D15 PT9C PT10C PT11C PT13C PT16C I/O
A14 PT9B PT10B PT11B PT13B PT16B I/O
C15 PT9A PT10A PT11A PT13A PT16A I/O-D3
B13 PT8D PT9D PT10D PT12D PT15D I/O
D13 PT8C PT9C PT10C PT12C PT15C I/O
A13 PT8B PT9B PT10B PT12B VDD5 I/O-VDD5
C14 PT8A PT9A PT10A PT12A PT15A I/O-D2
B12 PT7D PT8D PT9D PT11D PT14D I/O-D1
C13 PT7C PT8C PT9C PT11A PT14A I/O
Pin Information (continued)
Table 27. OR2C/2T10A, OR2C/2T12A, OR2C/2T15A/B, OR2C/2T26A, and OR2T40A/B 352-Pin PBGA
Pinout (conti nued)
Pin 2C/2T10A Pad 2C/2T12A Pad 2C/2T15A/B Pad 2C/2T26A Pad OR2T40A/B Pad Function
Notes:
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, but they are connected to VDD5 for the OR2TxxA series.
The pins labeled VSS-ETC are the 6 x 6 arra y of thermal balls located at the center of the package. The balls can be attached to the ground plane
of the board for enhanced ther mal capability (see Table 29), or they can be left unconnected.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 113
A12 PT7B PT8B PT9B PT10D PT13D I/O
B11 PT7A PT8A PT9A PT10A PT13A I/O-D0/DIN
C12 PT6D PT7D PT8D PT9D PT12D I/O
A11 PT6C PT7C PT8C PT9A PT12A I/O
D12 PT6B PT7B PT8B PT8D PT11D I/O
B10 PT6A PT7A PT8A PT8A/ PT11A I/O-DOUT
C11 PT5D PT6D PT7D PT7D PT10D I/O
A10 PT5C PT6C PT7C PT7C PT10A I/O
D10 PT5B PT6B PT7B PT7B PT9D I/O
B9 PT5A PT6A PT7A PT7A PT9A I/O
C10 PT4D PT5D PT6D PT6D PT8D I/O
A9 PT4C PT5C PT6C PT6C PT8A I/O
B8 PT4B PT5B PT6B PT6B PT7D I/O
A8 PT4A PT5A PT6A PT6A PT7A I/O-TDI
C9 — PT4D PT5D PT5D PT6D I/O
B7 PT3D PT4C PT5C PT5C PT6C I/O
D8 — PT4B PT5B PT5B PT6B I/O
A7 PT3C PT4A PT5A PT5A VDD5 I/O-VDD5
C8 — PT3D PT4D PT4D PT5D I/O
B6 PT3B PT3C PT4C PT4C PT5C I/O
D7 — PT3B PT4B PT4B PT5B I/O
A6 PT3A PT3A PT4A PT4A PT5A I/O-TMS
C7 PT2D PT2D PT3D PT3D PT4D I/O
B5 PT2C PT2C PT3A PT3A PT4A I/O
A5 PT2B PT2B PT2D PT2D PT3D I/O
C6 — — PT2C PT2C PT3C I/O
B4 — — PT2B PT2B PT3B I/O
D5 PT2A PT2A PT2A PT2A PT3A I/O
A4 PT1D PT1D PT1D PT1D PT2D I/O
C5 PT1C PT1C PT1C PT1C PT2A I/O
B3 PT1B PT1B PT1B PT1B PT1D I/O
C4 PT1A PT1A PT1A PT1A PT1A I/O-TCK
A3 RD_DATA/TDO RD_DATA/TDO RD_DATA/TDO RD_DATA/TDO RD_DATA/TDO RD_DATA/
TDO
A1 VSS VSS VSS VSS VSS VSS
A2 VSS VSS VSS VSS VSS VSS
A26 VSS VSS VSS VSS VSS VSS
AC13 VSS VSS VSS VSS VSS VSS
AC18 VSS VSS VSS VSS VSS VSS
AC23 VSS VSS VSS VSS VSS VSS
Pin Information (continued)
Table 27. OR2C/2T10A, OR2C/2T12A, OR2C/2T15A/B, OR2C/2T26A, and OR2T40A/B 352-Pin PBGA
Pinout (conti nued)
Pin 2C/2T10A Pad 2C/2T12A Pad 2C/2T15A/B Pad 2C/2T26A Pad OR2T40A/B Pad Function
Notes:
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB ser ies, but they are connected to VDD5 for the OR2TxxA series.
The pins labeled VSS-ETC are the 6 x 6 arra y of thermal balls located at the center of the package . The balls can be attached to the ground plane
of the board for enhanced ther mal capability (see Table 29), or they can be left unconnected.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
114 Lucent Technologies Inc.
AC4 VSS VSS VSS VSS VSS VSS
AC8 VSS VSS VSS VSS VSS VSS
AD24 VSS VSS VSS VSS VSS VSS
AD3 VSS VSS VSS VSS VSS VSS
AE1 VSS VSS VSS VSS VSS VSS
AE2 VSS VSS VSS VSS VSS VSS
AE25 VSS VSS VSS VSS VSS VSS
AF1 VSS VSS VSS VSS VSS VSS
AF25 VSS VSS VSS VSS VSS VSS
AF26 VSS VSS VSS VSS VSS VSS
B2 VSS VSS VSS VSS VSS VSS
B25 VSS VSS VSS VSS VSS VSS
B26 VSS VSS VSS VSS VSS VSS
C24 VSS VSS VSS VSS VSS VSS
C3 VSS VSS VSS VSS VSS VSS
D14 VSS VSS VSS VSS VSS VSS
D19 VSS VSS VSS VSS VSS VSS
D23 VSS VSS VSS VSS VSS VSS
D4 VSS VSS VSS VSS VSS VSS
D9 VSS VSS VSS VSS VSS VSS
H4 VSS VSS VSS VSS VSS VSS
J23 VSS VSS VSS VSS VSS VSS
N4 VSS VSS VSS VSS VSS VSS
P23 VSS VSS VSS VSS VSS VSS
V4 VSS VSS VSS VSS VSS VSS
W23 VSS VSS VSS VSS VSS VSS
AA23 VDD VDD VDD VDD VDD VDD
AA4 VDD VDD VDD VDD VDD VDD
AC11 VDD VDD VDD VDD VDD VDD
AC16 VDD VDD VDD VDD VDD VDD
AC21 VDD VDD VDD VDD VDD VDD
AC6 VDD VDD VDD VDD VDD VDD
D11 VDD VDD VDD VDD VDD VDD
D16 VDD VDD VDD VDD VDD VDD
D21 VDD VDD VDD VDD VDD VDD
D6 VDD VDD VDD VDD VDD VDD
F23 VDD VDD VDD VDD VDD VDD
F4 VDD VDD VDD VDD VDD VDD
L23 VDD VDD VDD VDD VDD VDD
Pin Information (continued)
Table 27. OR2C/2T10A, OR2C/2T12A, OR2C/2T15A/B, OR2C/2T26A, and OR2T40A/B 352-Pin PBGA
Pinout (conti nued)
Pin 2C/2T10A Pad 2C/2T12A Pad 2C/2T15A/B Pad 2C/2T26A Pad OR2T40A/B Pad Function
Notes:
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, but they are connected to VDD5 for the OR2TxxA series.
The pins labeled VSS-ETC are the 6 x 6 arra y of thermal balls located at the center of the package. The balls can be attached to the ground plane
of the board for enhanced ther mal capability (see Table 29), or they can be left unconnected.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 115
L4 VDD VDD VDD VDD VDD VDD
T23 VDD VDD VDD VDD VDD VDD
T4 VDD VDD VDD VDD VDD VDD
L11 VSS VSS VSS VSS VSS VSS—ETC
L12 VSS VSS VSS VSS VSS VSS—ETC
L13 VSS VSS VSS VSS VSS VSS—ETC
L14 VSS VSS VSS VSS VSS VSS—ETC
L15 VSS VSS VSS VSS VSS VSS—ETC
L16 VSS VSS VSS VSS VSS VSS—ETC
M11 VSS VSS VSS VSS VSS VSS—ETC
M12 VSS VSS VSS VSS VSS VSS—ETC
M13 VSS VSS VSS VSS VSS VSS—ETC
M14 VSS VSS VSS VSS VSS VSS—ETC
M15 VSS VSS VSS VSS VSS VSS—ETC
M16 VSS VSS VSS VSS VSS VSS—ETC
N11 VSS VSS VSS VSS VSS VSS—ETC
N12 VSS VSS VSS VSS VSS VSS—ETC
N13 VSS VSS VSS VSS VSS VSS—ETC
N14 VSS VSS VSS VSS VSS VSS—ETC
N15 VSS VSS VSS VSS VSS VSS—ETC
N16 VSS VSS VSS VSS VSS VSS—ETC
P11 VSS VSS VSS VSS VSS VSS—ETC
P12 VSS VSS VSS VSS VSS VSS—ETC
P13 VSS VSS VSS VSS VSS VSS—ETC
P14 VSS VSS VSS VSS VSS VSS—ETC
P15 VSS VSS VSS VSS VSS VSS—ETC
P16 VSS VSS VSS VSS VSS VSS—ETC
R11 VSS VSS VSS VSS VSS VSS—ETC
R12 VSS VSS VSS VSS VSS VSS—ETC
R13 VSS VSS VSS VSS VSS VSS—ETC
R14 VSS VSS VSS VSS VSS VSS—ETC
R15 VSS VSS VSS VSS VSS VSS—ETC
R16 VSS VSS VSS VSS VSS VSS—ETC
T11 VSS VSS VSS VSS VSS VSS—ETC
T12 VSS VSS VSS VSS VSS VSS—ETC
T13 VSS VSS VSS VSS VSS VSS—ETC
T14 VSS VSS VSS VSS VSS VSS—ETC
T15 VSS VSS VSS VSS VSS VSS—ETC
T16 VSS VSS VSS VSS VSS VSS—ETC
Pin Information (continued)
Table 27. OR2C/2T10A, OR2C/2T12A, OR2C/2T15A/B, OR2C/2T26A, and OR2T40A/B 352-Pin PBGA
Pinout (conti nued)
Pin 2C/2T10A Pad 2C/2T12A Pad 2C/2T15A/B Pad 2C/2T26A Pad OR2T40A/B Pad Function
Notes:
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB ser ies, but they are connected to VDD5 for the OR2TxxA series.
The pins labeled VSS-ETC are the 6 x 6 arra y of thermal balls located at the center of the package . The balls can be attached to the ground plane
of the board for enhanced ther mal capability (see Table 29), or they can be left unconnected.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
116 Lucent Technologies Inc.
Pin Information (continued)
Table 28. OR2C/2T15A, OR2C/2T26A, and OR2C/2T40A/B 432-Pin EBGA Pinout
Pin 2C/2T15A Pad 2C/2T26A Pad 2C/2T40A/B Pad Function
E28 PL1D PL1D PL1D I/O
D29 PL1C PL1C PL1A I/O
D30 PL1B PL1B PL2D I/O
D31 PL1A PL1A PL2A I/O
F28 PL2D PL2D PL3D I/O-A0
E29 PL2C PL2C PL3C I/O
E30 PL2B PL2B PL3B I/O
E31 PL2A PL2A PL3A I/O
F29 PL3D PL3D PL4D I/O
F30 PL3C PL3C PL4C I/O
F31 PL3B PL3B PL4B I/O
H28 PL3A PL3A PL4A I/O
G29 PL4D PL4D PL5D I/O-VDD5
G30 PL4C PL4C PL5C I/O
G31 PL4B PL4B PL5B I/O
J28 PL4A PL4A PL6D I/O
H29 PL5D PL5D PL7D I/O
H30 PL5C PL5C PL7C I/O
J29 PL5B PL5B PL7B I/O
K28 PL5A PL5A PL8D I/O-A1
J30 PL6D PL6D PL9D I/O
J31 PL6C PL6C PL9C I/O
K29 PL6B PL6B PL9B I/O
K30 PL6A PL6A PL9A I/O-A2
K31 PL7D PL7D PL10D I/O
L29 PL7C PL7C PL10C I/O
M28 PL7B PL7B PL10B I/O
L30 PL7A PL7A PL10A I/O-A3
L31 — PL8D PL11D I/O-VDD5
M29 PL8D PL8C PL11C I/O
N28 PL8C PL8A PL11A I/O
M30 PL8B PL9D PL12D I/O
N29 — PL9C PL12C I/O
N30 PL8A PL9A PL12A I/O-A4
P28 PL9D PL10D PL13D I/O-A5
N31 — PL10C PL13C I/O
P29 PL9C PL10A PL13A I/O
P30 PL9B PL11D PL14D I/O
P31 PL9A PL11A PL14A I/O-A6
R29 PL10D PL12D PL15D I/O
R30 PL10C PL12C PL15C I/O
R31 PL10B PL12B PL15B I/O
T29 PL10A PL12A PL15A I/O-A7
Notes:
The OR2T15A pin AG2 is not connected in the 432-pin EBGA package.
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, but they are connected to VDD5 for the OR2TxxA series.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 117
T28 PL11D PL13D PL16D I/O
T30 PL11C PL13C PL16C I/O-VDD5
U31 PL11B PL13B PL16B I/O
U30 PL11A PL13A PL16A I/O-A8
U29 PL12D PL14D PL17D I/O-A9
V31 — PL14C PL17C I/O
V30 PL12C PL14A PL17A I/O
V29 PL12B PL15D PL18D I/O
W31 — PL15C PL18C I/O
V28 PL12A PL15A PL18A I/O-A10
W30 PL13D PL16D PL19D I/O
W29 — PL16C PL19C I/O
Y30 PL13C PL16A PL19A I/O
W28 PL13B PL17D PL20D I/O
Y29 PL13A PL17A PL20A I/O-A11
AA31 PL14D PL18D PL21D I/O-A12
AA30 PL14C PL18C PL21C I/O
Y28 PL14B PL18B PL21B I/O
AA29 PL14A PL18A PL21A I/O
AB31 PL15D PL19D PL22D I/O
AB30 PL15C PL19C PL22C I/O
AB29 PL15B PL19B PL22B I/O-A13
AC31 PL15A PL19A PL22A I/O
AC30 PL16D PL20D PL23D I/O
AB28 PL16C PL20C PL23C I/O
AC29 PL16B PL20B PL24D I/O
AD30 PL16A PL20A PL25D I/O
AD29 PL17D PL21D PL25A I/O-A14
AC28 PL17C PL21C PL26C I/O
AE31 PL17B PL21B PL26B I/O
AE30 PL17A PL21A PL26A I/O
AE29 PL18D PL22D PL27D I/O-VDD5
AD28 PL18C PL22C PL27C I/O
AF31 PL18B PL22B PL27B I/O
AF30 PL18A PL22A PL27A I/O
AF29 PL19D PL23D PL28D I/O
AG31 PL19C PL23C PL28C I/O
AG30 PL19B PL23B PL28B I/O
AG29 PL19A PL23A PL28A I/O
AF28 PL20D PL24D PL29A I/O
AH31 PL20C PL24C PL30C I/O
AH30 PL20B PL24B PL30B I/O
AH29 PL20A PL24A PL30A I/O-A15
AG28 CCLK CCLK CCLK CCLK
Pin Information (continued)
Table 28. OR2C/2T15A, OR2C/2T26A, and OR2C/2T40A/B 432-Pin EBGA Pinout (continued)
Pin 2C/2T15A Pad 2C/2T26A Pad 2C/2T40A/B Pad Function
Notes:
The OR2T15A pin AG2 is not connected in the 432-pin EBGA package.
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, but they are connected to VDD5 for the OR2TxxA series.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
118 Lucent Technologies Inc.
AH27 PB1A PB1A PB1A I/O-A16
AJ28 PB1B PB1B PB1B I/O
AK28 PB1C PB1C PB2A I/O
AL28 PB1D PB1D PB2D I/O
AH26 PB2A PB2A PB3A I/O
AJ27 PB2B PB2B PB3B I/O
AK27 PB2C PB2C PB3C I/O
AL27 PB2D PB2D PB3D I/O-VDD5
AJ26 PB3A PB3A PB4A I/O
AK26 PB3B PB3B PB4B I/O
AL26 PB3C PB3C PB4C I/O
AH24 PB3D PB3D PB4D I/O
AJ25 PB4A PB4A PB5A I/O
AK25 PB4B PB4B PB5B I/O
AL25 PB4C PB4C PB5C I/O
AH23 PB4D PB4D PB5D I/O-A17
AJ24 PB5A PB5A PB6A I/O
AK24 PB5B PB5B PB6B I/O
AJ23 PB5C PB5C PB6C I/O
AH22 PB5D PB5D PB6D I/O
AK23 PB6A PB6A PB7A I/O
AL23 PB6B PB6B PB7D I/O
AJ22 PB6C PB6C PB8A I/O
AK22 PB6D PB6D PB8D I/O
AL22 PB7A PB7A PB9A I/O
AJ21 PB7B PB7B PB9D I/O
AH20 PB7C PB7C PB10A I/O
AK21 PB7D PB7D PB10D I/O
AL21 — PB8A PB11A I/O-VDD5
AJ20 PB8A PB8B PB11B I/O
AH19 PB8B PB8D PB11D I/O
AK20 PB8C PB9A PB12A I/O
AJ19 — PB9B PB12B I/O
AK19 PB8D PB9D PB12D I/O
AH18 PB9A PB10A PB13A I/O
AL19 PB9B PB10D PB13D I/O
AJ18 PB9C PB11A PB14A I/O
AK18 — PB11B PB14B I/O
AL18 PB9D PB11D PB14D I/O
AJ17 PB10A PB12A PB15A I/O
AK17 PB10B PB12B PB15B I/O
AL17 PB10C PB12C PB15C I/O
AJ16 PB10D PB12D PB15D I/O
AH16 PB11A PB13A PB16A I/O
Pin Information (continued)
Table 28. OR2C/2T15A, OR2C/2T26A, and OR2C/2T40A/B 432-Pin EBGA Pinout (continued)
Pin 2C/2T15A Pad 2C/2T26A Pad 2C/2T40A/B Pad Function
Notes:
The OR2T15A pin AG2 is not connected in the 432-pin EBGA package.
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, but they are connected to VDD5 for the OR2TxxA series.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 119
AK16 PB11B PB13B PB16B I/O
AL15 PB11C PB13C PB16C I/O
AK15 PB11D PB13D PB16D I/O
AJ15 PB12A PB14A PB17A I/O-VDD5
AL14 PB12B PB14D PB17D I/O
AK14 PB12C PB15A PB18A I/O
AJ14 — PB15B PB18B I/O
AL13 PB12D PB15D PB18D I/O
AH14 PB13A PB16A PB19A I/O-HDC
AK13 — PB16B PB19B I/O
AJ13 PB13B PB16D PB19D I/O
AK12 PB13C PB17A PB20A I/O
AH13 — PB17B PB20B I/O
AJ12 PB13D PB17D PB20D I/O
AL11 PB14A PB18A PB21A I/O-LDC
AK11 PB14B PB18B PB21D I/O
AH12 PB14C PB18C PB22A I/O
AJ11 PB14D PB18D PB22D I/O
AL10 PB15A PB19A PB23A I/O
AK10 PB15B PB19B PB24A I/O
AJ10 PB15C PB19C PB24C I/O
AL9 PB15D PB19D PB24D I/O
AK9 PB16A PB20A PB25A I/O-INIT
AH10 PB16B PB20B PB25B I/O
AJ9 PB16C PB20C PB25C I/O
AK8 PB16D PB20D PB25D I/O
AJ8 PB17A PB21A PB26A I/O-VDD5
AH9 PB17B PB21B PB26B I/O
AL7 PB17C PB21C PB26C I/O
AK7 PB17D PB21D PB26D I/O
AJ7 PB18A PB22A PB27A I/O
AH8 PB18B PB22B PB27B I/O
AL6 PB18C PB22C PB27C I/O
AK6 PB18D PB22D PB27D I/O
AJ6 PB19A PB23A PB28A I/O
AL5 PB19B PB23B PB28B I/O
AK5 PB19C PB23C PB28C I/O
AJ5 PB19D PB23D PB28D I/O
AH6 PB20A PB24A PB29A I/O
AL4 PB20B PB24B PB29D I/O
AK4 PB20C PB24C PB30C I/O
AJ4 PB20D PB24D PB30D I/O
AH5 DONE DONE DONE DONE
AG4 RESET RESET RESET RESET
Pin Information (continued)
Table 28. OR2C/2T15A, OR2C/2T26A, and OR2C/2T40A/B 432-Pin EBGA Pinout (continued)
Pin 2C/2T15A Pad 2C/2T26A Pad 2C/2T40A/B Pad Function
Notes:
The OR2T15A pin AG2 is not connected in the 432-pin EBGA package.
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, but they are connected to VDD5 for the OR2TxxA series.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
120 Lucent Technologies Inc.
AH3 PRGM PRGM PRGM PRGM
AH2 PR20A PR24A PR30A I/O-M0
AH1 PR20B PR24B PR30B I/O
AF4 PR20C PR24C PR29A I/O
AG3 PR20D PR24D PR29D I/O
AG2 PR19A PR23A PR28A I/O-VDD5
AG1 PR19B PR23B PR28B I/O
AF3 PR19C PR23C PR28C I/O
AF2 PR19D PR23D PR28D I/O
AF1 PR18A PR22A PR27A I/O
AD4 PR18B PR22B PR27B I/O
AE3 PR18C PR22C PR27C I/O
AE2 PR18D PR22D PR27D I/O
AE1 PR17A PR21A PR26A I/O
AC4 PR17B PR21B PR26B I/O
AD3 PR17C PR21C PR26C I/O
AD2 PR17D PR21D PR25A I/O
AC3 PR16A PR20A PR24A I/O
AB4 PR16B PR20B PR24B I/O
AC2 PR16C PR20C PR24D I/O
AC1 PR16D PR20D PR23D I/O-M1
AB3 PR15A PR19A PR22A I/O
AB2 PR15B PR19B PR22B I/O
AB1 PR15C PR19C PR22C I/O
AA3 PR15D PR19D PR22D I/O-VDD5
Y4 PR14A PR18A PR21A I/O
AA2 PR14B PR18B PR21B I/O
AA1 PR14C PR18C PR21C I/O
Y3 PR14D PR18D PR21D I/O
W4 PR13A PR17A PR20A I/O-M2
Y2 PR13B PR17D PR20D I/O
W3 PR13C PR16A PR19A I/O
W2 PR13D PR16B PR19B I/O
V4 — PR16D PR19D I/O
W1 PR12A PR15A PR18A I/O-M3
V3 — PR15D PR18D I/O
V2 PR12B PR14A PR17A I/O
V1 PR12C PR14B PR17B I/O
U3 PR12D PR14D PR17D I/O
U2 PR11A PR13A PR16A I/O
U1 PR11B PR13B PR16B I/O
T3 PR11C PR13C PR16C I/O
T4 PR11D PR13D PR16D I/O
T2 PR10A PR12A PR15A I/O
Pin Information (continued)
Table 28. OR2C/2T15A, OR2C/2T26A, and OR2C/2T40A/B 432-Pin EBGA Pinout (continued)
Pin 2C/2T15A Pad 2C/2T26A Pad 2C/2T40A/B Pad Function
Notes:
The OR2T15A pin AG2 is not connected in the 432-pin EBGA package.
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, but they are connected to VDD5 for the OR2TxxA series.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 121
R1 PR10B PR12B PR15B I/O
R2 PR10C PR12C PR15C I/O
R3 PR10D PR12D PR15D I/O
P1 PR9A PR11A PR14A I/O-VDD5
P2 PR9B PR11C PR14C I/O
P3 PR9C PR11D PR14D I/O
N1 — PR10A PR13A I/O
P4 PR9D PR10C PR13C I/O
N2 — PR10D PR13D I/O
N3 PR8A PR9A PR12A I/O-CS1
M2 PR8B PR9D PR12D I/O
N4 PR8C PR8A PR11A I/O
M3 PR8D PR8D PR11D I/O
L1 PR7A PR7A PR10A I/O-CS0
L2 PR7B PR7B PR10B I/O
M4 PR7C PR7C PR10C I/O
L3 PR7D PR7D PR10D I/O
K1 PR6A PR6A PR9A I/O
K2 PR6B PR6B PR9B I/O
K3 PR6C PR6C PR9C I/O
J1 PR6D PR6D PR9D I/O
J2 PR5A PR5A PR8A I/O-RD
K4 PR5B PR5B PR7A I/O
J3 PR5C PR5C PR7C I/O
H2 PR5D PR5D PR6A I/O
H3 PR4A PR4A PR5A I/O-VDD5
J4 PR4B PR4B PR5B I/O
G1 PR4C PR4C PR5C I/O
G2 PR4D PR4D PR5D I/O
G3 PR3A PR3A PR4A I/O-WR
H4 PR3B PR3B PR4B I/O
F1 PR3C PR3C PR4C I/O
F2 PR3D PR3D PR4D I/O
F3 PR2A PR2A PR3A I/O
E1 PR2B PR2B PR3B I/O
E2 PR2C PR2C PR3C I/O
E3 PR2D PR2D PR3D I/O
F4 PR1A PR1A PR2A I/O
D1 PR1B PR1B PR2D I/O
D2 PR1C PR1C PR1A I/O
D3 PR1D PR1D PR1D I/O
E4 RD_CFGN RD_CFGN RD_CFGN RD_CFGN
D5 PT20D PT24D PT30D I/O
C4 PT20C PT24C PT30A I/O
Pin Information (continued)
Table 28. OR2C/2T15A, OR2C/2T26A, and OR2C/2T40A/B 432-Pin EBGA Pinout (continued)
Pin 2C/2T15A Pad 2C/2T26A Pad 2C/2T40A/B Pad Function
Notes:
The OR2T15A pin AG2 is not connected in the 432-pin EBGA package.
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, but they are connected to VDD5 for the OR2TxxA series.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
122 Lucent Technologies Inc.
B4 PT20B PT24B PT29B I/O
A4 PT20A PT24A PT29A I/O
D6 PT19D PT23D PT28D I/O
C5 PT19C PT23C PT28C I/O
B5 PT19B PT23B PT28B I/O
A5 PT19A PT23A PT28A I/O-RDY/RCLK
C6 PT18D PT22D PT27D I/O
B6 PT18C PT22C PT27C I/O
A6 PT18B PT22B PT27B I/O
D8 PT18A PT22A PT27A I/O
C7 PT17D PT21D PT26D I/O
B7 PT17C PT21C PT26C I/O
A7 PT17B PT21B PT26B I/O
D9 PT17A PT21A PT26A I/O
C8 PT16D PT20D PT25D I/O-D7
B8 PT16C PT20C PT25C I/O
C9 PT16B PT20B PT25B I/O
D10 PT16A PT20A PT25A I/O
B9 PT15D PT19D PT24D I/O-VDD5
A9 PT15C PT19C PT24C I/O
C10 PT15B PT19B PT24B I/O
B10 PT15A PT19A PT23D I/O
A10 PT14D PT18D PT22D I/O
C11 PT14C PT18C PT22A I/O
D12 PT14B PT18B PT21D I/O-D6
B11 PT14A PT18A PT21A I/O
A11 PT13D PT17D PT20D I/O
C12 PT13C PT17A PT20A I/O
D13 — PT16D PT19D I/O-VDD5
B12 PT13B PT16B PT19B I/O
C13 PT13A PT16A PT19A I/O-D5
B13 PT12D PT15D PT18D I/O
D14 — PT15B PT18B I/O
A13 PT12C PT15A PT18A I/O
C14 PT12B PT14D PT17D I/O
B14 — PT14B PT17B I/O
A14 PT12A PT14A PT17A I/O-D4
C15 PT11D PT13D PT16D I/O
B15 PT11C PT13C PT16C I/O
A15 PT11B PT13B PT16B I/O
C16 PT11A PT13A PT16A I/O-D3
D16 PT10D PT12D PT15D I/O
B16 PT10C PT12C PT15C I/O
A17 PT10B PT12B PT15B I/O-VDD5
Pin Information (continued)
Table 28. OR2C/2T15A, OR2C/2T26A, and OR2C/2T40A/B 432-Pin EBGA Pinout (continued)
Pin 2C/2T15A Pad 2C/2T26A Pad 2C/2T40A/B Pad Function
Notes:
The OR2T15A pin AG2 is not connected in the 432-pin EBGA package.
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, but they are connected to VDD5 for the OR2TxxA series.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 123
B17 PT10A PT12A PT15A I/O-D2
C17 PT9D PT11D PT14D D1
A18 — PT11C PT14C I/O
B18 PT9C PT11A PT14A I/O
C18 PT9B PT10D PT13D I/O
A19 — PT10C PT13C I/O
D18 PT9A PT10A PT13A I/O-D0/DIN
B19 PT8D PT9D PT12D I/O
C19 — PT9C PT12C I/O
B20 PT8C PT9A PT12A I/O
D19 PT8B PT8D PT11D I/O
C20 PT8A PT8A PT11A I/O-DOUT
A21 PT7D PT7D PT10D I/O
B21 PT7C PT7C PT10A I/O
D20 PT7B PT7B PT9D I/O
C21 PT7A PT7A PT9A I/O
A22 PT6D PT6D PT8D I/O
B22 PT6C PT6C PT8A I/O
C22 PT6B PT6B PT7D I/O
A23 PT6A PT6A PT7A I/O-TDI
B23 PT5D PT5D PT6D I/O
D22 PT5C PT5C PT6C I/O
C23 PT5B PT5B PT6B I/O
B24 PT5A PT5A PT6A I/O-VDD5
C24 PT4D PT4D PT5D I/O
D23 PT4C PT4C PT5C I/O
A25 PT4B PT4B PT5B I/O
B25 PT4A PT4A PT5A I/O-TMS
C25 PT3D PT3D PT4D I/O
D24 PT3C PT3C PT4C I/O
A26 PT3B PT3B PT4B I/O
B26 PT3A PT3A PT4A I/O
C26 PT2D PT2D PT3D I/O
A27 PT2C PT2C PT3C I/O
B27 PT2B PT2B PT3B I/O
C27 PT2A PT2A PT3A I/O
D26 PT1D PT1D PT2D I/O
A28 PT1C PT1C PT2A I/O
B28 PT1B PT1B PT1D I/O
C28 PT1A PT1A PT1A I/O-TCK
D27 RD_DATA/TDO RD_DATA/TDO RD_DATA/TDO RD_DATA/TDO
A12 VSS VSS VSS VSS
A16 VSS VSS VSS VSS
A2 VSS VSS VSS VSS
Pin Information (continued)
Table 28. OR2C/2T15A, OR2C/2T26A, and OR2C/2T40A/B 432-Pin EBGA Pinout (continued)
Pin 2C/2T15A Pad 2C/2T26A Pad 2C/2T40A/B Pad Function
Notes:
The OR2T15A pin AG2 is not connected in the 432-pin EBGA package.
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, but they are connected to VDD5 for the OR2TxxA series.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
124 Lucent Technologies Inc.
A20 VSS VSS VSS VSS
A24 VSS VSS VSS VSS
A29 VSS VSS VSS VSS
A3 VSS VSS VSS VSS
A30 VSS VSS VSS VSS
A8 VSS VSS VSS VSS
AD1 VSS VSS VSS VSS
AD31 VSS VSS VSS VSS
AJ1 VSS VSS VSS VSS
AJ2 VSS VSS VSS VSS
AJ30 VSS VSS VSS VSS
AJ31 VSS VSS VSS VSS
AK1 VSS VSS VSS VSS
AK29 VSS VSS VSS VSS
AK3 VSS VSS VSS VSS
AK31 VSS VSS VSS VSS
AL12 VSS VSS VSS VSS
AL16 VSS VSS VSS VSS
AL2 VSS VSS VSS VSS
AL20 VSS VSS VSS VSS
AL24 VSS VSS VSS VSS
AL29 VSS VSS VSS VSS
AL3 VSS VSS VSS VSS
AL30 VSS VSS VSS VSS
AL8 VSS VSS VSS VSS
B1 VSS VSS VSS VSS
B29 VSS VSS VSS VSS
B3 VSS VSS VSS VSS
B31 VSS VSS VSS VSS
C1 VSS VSS VSS VSS
C2 VSS VSS VSS VSS
C30 VSS VSS VSS VSS
C31 VSS VSS VSS VSS
H1 VSS VSS VSS VSS
H31 VSS VSS VSS VSS
M1 VSS VSS VSS VSS
M31 VSS VSS VSS VSS
T1 VSS VSS VSS VSS
T31 VSS VSS VSS VSS
Y1 VSS VSS VSS VSS
Y31 VSS VSS VSS VSS
A1 VDD VDD VDD VDD
A31 VDD VDD VDD VDD
Pin Information (continued)
Table 28. OR2C/2T15A, OR2C/2T26A, and OR2C/2T40A/B 432-Pin EBGA Pinout (continued)
Pin 2C/2T15A Pad 2C/2T26A Pad 2C/2T40A/B Pad Function
Notes:
The OR2T15A pin AG2 is not connected in the 432-pin EBGA package.
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, but they are connected to VDD5 for the OR2TxxA series.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 125
AA28 VDD VDD VDD VDD
AA4 VDD VDD VDD VDD
AE28 VDD VDD VDD VDD
AE4 VDD VDD VDD VDD
AH11 VDD VDD VDD VDD
AH15 VDD VDD VDD VDD
AH17 VDD VDD VDD VDD
AH21 VDD VDD VDD VDD
AH25 VDD VDD VDD VDD
AH28 VDD VDD VDD VDD
AH4 VDD VDD VDD VDD
AH7 VDD VDD VDD VDD
AJ29 VDD VDD VDD VDD
AJ3 VDD VDD VDD VDD
AK2 VDD VDD VDD VDD
AK30 VDD VDD VDD VDD
AL1 VDD VDD VDD VDD
AL31 VDD VDD VDD VDD
B2 VDD VDD VDD VDD
B30 VDD VDD VDD VDD
C29 VDD VDD VDD VDD
C3 VDD VDD VDD VDD
D11 VDD VDD VDD VDD
D15 VDD VDD VDD VDD
D17 VDD VDD VDD VDD
D21 VDD VDD VDD VDD
D25 VDD VDD VDD VDD
D28 VDD VDD VDD VDD
D4 VDD VDD VDD VDD
D7 VDD VDD VDD VDD
G28 VDD VDD VDD VDD
G4 VDD VDD VDD VDD
L28 VDD VDD VDD VDD
L4 VDD VDD VDD VDD
R28 VDD VDD VDD VDD
R4 VDD VDD VDD VDD
U28 VDD VDD VDD VDD
U4 VDD VDD VDD VDD
Pin Information (continued)
Table 28. OR2C/2T15A, OR2C/2T26A, and OR2C/2T40A/B 432-Pin EBGA Pinout (continued)
Pin 2C/2T15A Pad 2C/2T26A Pad 2C/2T40A/B Pad Function
Notes:
The OR2T15A pin AG2 is not connected in the 432-pin EBGA package.
The pins labeled I/O-VDD5 are user I/Os for the OR2CxxA and OR2TxxB series, but they are connected to VDD5 for the OR2TxxA series.
Lucent Technologies Inc. 126
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Package Thermal Characteristics
There are three thermal parameters that are in com-
mon use: ΘJA, ψJC, and ΘJC. It should be noted that all
the parameters are affected, to varying degrees, by
package design (including paddle size) and choice of
materials, the amount of copper in the test board or
system board, and system airflow.
The data base containing the thermal values for all of
Lucent Technologies’ IC packages is currently being
updated to conform to modern JEDEC standards.
Thus, Tab le 29 contains the currently available thermal
specifications for Lucent Technologies’ FPGA pack-
ages mounted on both JEDEC and non-JEDEC test
boards. The thermal values for the newer pac kage
types correspond to those packages mounted on a
JEDEC four-layer board (indicated as Note 2 in the
table). The v alues f or the older packages, however, cor-
respond to those packages mounted on a non-JEDEC ,
single-layer, sparse copper board (see Note 1). It
should also be noted that the values for the older pack-
ages are considered conservative.
ΘJA
This is the thermal resistance from junction to ambient
(a.k.a. theta-J A, R-theta, etc.).
where TJ is the junction temperature, TA is the ambient
air temperature, and Q is the chip power.
Experimentally, ΘJA is determined when a special ther-
mal test die is assembled into the package of interest,
and the part is mounted on the thermal test board. The
diodes on the test chip are separately calibrated in an
oven. The package/board is placed either in a JEDEC
natural convection box or in the wind tunnel, the latter
for forced convection measurements. A controlled
amount of power (Q) is dissipated in the test chip’s
heater resistor, the chip’s temperature (TJ) is deter-
mined by the f orward drop on the diodes, and the ambi-
ent temperature (TA) is noted. Note that ΘJA is
expressed in units of °C/watt.
ψJC
This JEDEC designated parameter correlates the junc-
tion temperature to the case temperature. It is generally
used to infer the junction temperature while the device
is operating in the system. It is not considered a true
thermal resistance, and it is defined by:
where TC is the case temperature at top dead center,
TJ is the junction temperature, and Q is the chip power.
During the ΘJA measurements described above,
besides the other parameters measured, an additional
temperature reading, TC, is made with a thermocouple
attached at top-dead-center of the case. ψJC is also
ex pres sed in uni ts of °C /watt.
ΘJC
This is the thermal resistance from junction to case. It
is most often used when attaching a heat sink to the
top of the package. It is defined by:
The parameters in this equation have been defined
above. However, the measurements is performed with
the case of the part pressed against a water-cooled
heat sink so as to draw most of the heat generated by
the chip out the top of the package. It is this difference
in the measurement process that differentiates ΘJC
from ψJC. ΘJC is a true thermal resistance and is
expressed in units of °C/watt.
ΘJB
This is the thermal resistance from junction to board
(a.k.a., ΘJL). It is defined by:
where TB is the temperature of the board adjacent to a
lead measured with a thermocouple. The other param-
eters on the right-hand side have been defined above.
This is considered a true thermal resistance, and the
measurement is made with a water-cooled heat sink
pressed against the board so as to dra w most of the
heat out of the leads . Note that ΘJB is e xpressed in
units of °C/watt, and that this parameter and the way it
is measured is still in JEDEC committee.
ΘJA TJTA
–
Q
--------------------=
ψJC TJTC
–
Q
--------------------=
ΘJC TJTC
–
Q
--------------------=
ΘJB TJTB
–
Q
--------------------=
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 127
Package Thermal Characteristics (continued)
FPGA Maximum Junction Temperature
Once the power dissipated by the FPGA has been determined (see the Estimating Power Dissipation section), the
maximum junction temperature of the FPGA can be found. This is needed to determine if speed derating of the
device from the 85 °C junction temperature used in all of the delay tables is needed. Using the maximum ambient
temperature, TAmax, and the power dissipated by the device, Q (expressed in °C), the maximum junction tempera-
ture is approximated b y:
TJmax = TAmax + (Q • ΘJA)
Tab le 29 lists the thermal characteristics for all packages used with the Series 2 FPGAs.
1. Mounted on a sparse coppe r one-layer test board.
2. Mounted on four-layer JEDEC standard test board with two power/g r ound planes .
3. With thermal balls connected to board ground plane.
4. Without thermal balls connected to board ground plane.
Note: The ψJC for the pac kages listed is <1 °C/ W. This implies that virtually all of t he heat is dissipated through the board on which the pa c kage
is mounted.
Table 29. Series 2 Plastic Package Thermal Guidelines
Package ΘJA (°C/W) TA = 70 °C max
TJ = 125 °C max
@ 0 fpm (W)
0 fpm 200 fpm 500 fpm
84-Pin PLCC140.0 35.0 — 1.4
100-Pin TQFP230.0—27.0 26—23 24.0—21.0 1.8—2.0
144-Pin TQFP152.0 39.0 — 1.1
160-Pin QFP224.0 21.5 20.5 2.3
208-Pin SQFP226.5 23.0 21.0 2.1
208-Pin SQFP2212.8 10.3 9.1 4.3
240-Pin SQFP225.5 22.5 21.0 2.2
240-Pin SQFP2213.0 10.0 9.0 4.2
256-Pin PBGA2, 3 22.5 19.0 17.5 2.4
256-Pin PBGA2, 4 26.0 22.0 20.5 2.1
304-Pin SQFP227.5 24.0 22.5 2.0
304-Pin SQFP2212.0 10.0 9.0 4.6
352-Pin PBGA2, 3 19.0 16.0 15.0 2.9
352-Pin PBGA2, 4 25.5 22.0 20.5 2.1
432-Pin EBGA211.0 8.5 7.5 5.0
Package Coplanarity
The coplanarity limits of the Series 2
series packages
are as follows:
■TQFP: 3.15 mils
■PLCC and QFP: 4.0 mils
■PBGA: 8.0 mils
■SQFP: 4.0 mils (240 and 304 only)
3.15 mils (all other sizes)
■SQFP2: 3.15 mils
■EBGA: 8.0 mils
Package Parasitics
The electrical performance of an IC package, such as
signal quality and noise sensitivity, is directly affected
by the package parasitics. Table 30 lists eight parasitics
associated with the
ORCA
packages. These parasitics
represent the contributions of all components of a
package, which include the bond wires, all internal
package routing, and the external leads.
Four inductances in nH are listed: LSW and LSL, the
self-inductance of the lead; and LMW and LML, the
mutual inductance to the nearest neighbor lead.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
128 Lucent Technologies Inc.
Package Parasitics (continued)
These parameters are important in determining ground bounce noise and inductive crosstalk noise. Three capaci-
tances in pF are listed: CM, the mutual capacitance of the lead to the nearest neighbor lead; and C1 and C2, the
total capacitance of the lead to all other leads (all other leads are assumed to be grounded). These parameters are
important in determining capacitive crosstalk and the capacitive loading effect of the lead.
The parasitic values in Table 30 are for the circuit model of bond wire and package lead parasitics. If the mutual
capacitance value is not used in the designer’ s model, then the value listed as mutual capacitance should be added
to each of the C1 and C2 capacitors.
5-3862(F).r2
Figure 53. Package Parasitics
Table 30. Series 2 Package Parasitics
Package Ty p e L SW LMW RWC1C2CMLSL LML
84-Pin PLC C 3 1 140 1 1 0.5 7—11 3—6
100-Pin TQFP 3 1 150 0.5 0.5 0.4 4—6 2—3
144-Pin TQFP 3 1 140 1 1 0.6 4—6 2—2.5
160-Pin QFP 4 1.5 180 1.5 1.5 1 10—13 6—8
208-Pin SQFP 4 2 200 1 1 1 7—10 4—6
208-Pin SQFP2 4 2 200 1 1 1 6—9 4—6
240-Pin SQFP 4 2 200 1 1 1 8—12 5—8
240-Pin SQFP2 4 2 200 1 1 1 7—11 4—7
256-Pin PBGA 5 2 220 1 1 1 5—8 2—4
304-Pin SQFP 5 2 220 1 1 1 12—18 7—12
304-Pin SQFP2 5 2 220 1 1 1 11—17 7—12
352-Pin PBGA 5 2 220 1.5 1.5 1.5 7—12 3—6
432-Pin EBGA 4 1.5 500 1 1 0.3 3—5.5 0.5—1
PAD N
CIRCUIT
BOARD PAD
CM
C1
LWRWLL
LMW
C2
C1
LML
C2
PAD N + 1
LWRWLL
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 129
Absolute Maximum Ratings
Stresses in e xcess of the absolute maximum ratings can cause permanent damage to the device. These are abso-
lute stress ratings only. Functional operation of the device is not implied at these or any other conditions in excess of
those given in the operations sections of this data sheet. Exposure to absolute maximum ratings for e xtended periods
can adversely affect device reliability.
The
ORCA
Series FPGAs include circuitry designed to protect the chips from damaging substrate injection currents
and prevent accumulations of static charge. Nevertheless, conventional precautions should be observed during stor-
age, handling, and use to av oid exposure to excessive electrical stress.
Recommended Operating Conditions
Notes:
During powerup and powerdown sequencing, VDD is allowed to be at a higher voltage level than VDD5 for up to 100 ms.
During powerup sequencing of OR2TxxA devices VDD should reach 1.0 V before v oltage applied t o VDD5 can be gr eater than the v ol tage applied
to VDD.
The maximum recommended junction temperature (TJ) during operation is 125 °C.
* VDD5 not used in OR2TxxB dev ices.
Parameter Symbol Min Max Unit
Storage Temper ature Tstg –65 150 °C
Supply Voltage with Respect to Ground VDD –0.5 7.0 V
VDD5 Supply V oltage with Respect to Ground
(OR2TxxA) VDD5V
DD 7.0 V
Input Signal with Respect to Ground
OR2TxxA only — –0.5 VDD + 0.3
VDD5 + 0.3 V
Signal Applied to High-impedance Output
OR2TxxA only — –0.5 VDD + 0.3
VDD5 + 0.3 V
Maximum Soldering Temperature — — 260 °C
Mode
OR2CxxA OR2TxxA/OR2TxxB
Temperature
Range
(Ambient)
Supply Voltage
(VDD)Temperature
Range
(Ambient)
Supply Voltage
(VDD)Supply Voltage*
(VDD5)
Commercial 0 °C to 70 °C 5 V ± 5% 0 °C to 70 °C 3.0 V to 3.6 V VDD to 5.25 V
Industrial –40 °C to +85 °C 5 V ± 10% –40 °C to +85 °C 3.0 V to 3.6 V VDD to 5.25 V
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
130 Lucent Technologies Inc.
Electrical Characteristics
* On the OR2TxxA dev ices, the pull-up resistor will ex ter nally pull the pin to a level 1.0 V below VDD.
Table 31A. OR2CxxA and OR2TxxA Electrical Characteristics
OR2CxxA Commercial: VDD = 5.0 V ± 5%, 0 °C ≤ TA ≤ 70 °C; OR2CxxA Industrial: VDD = 5. 0 V ± 10%, –40 ° C ≤ TA ≤ +85 °C.
OR2TxxA Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2TxxA Industrial: VDD = 3.0 V to 3.6 V, –40 °C ≤ TA ≤
+85 °C.
Parameter Sym-
bol Test Condi tions OR2CxxA OR2TxxA Unit
Min Max Min Max
Input Voltage:
High
Low VIH
VIL
Inpu t confi gu red as C MOS 50% VDD
GND – 0.5 VDD + 0.3
30% VDD 50% VDD5
GND – 0.5 VDD5 + 0.3
30% VDD5 V
V
Input Voltage:
High
Low VIH
VIL
Input configured as TTL
(valid for OR2CxxA only) 2.0
–0.5 VDD + 0.3
0.8 —
— —
—V
V
Output Voltage:
High
Low VOH
VOL VDD = min, IOH = 6 mA or 3 mA
VDD = min, IOL = 12 mA or 6 mA 2.4
——
0.4 2.4
——
0.4 V
V
Input Leakage Current ILVDD = Max, VIN = VSS or VDD –10 10 –10 10 µA
Standby Current:
OR2C04A/OR2T04A
OR2C06A/OR2T06A
OR2C08A/OR2T08A
OR2C10A/OR2T10A
OR2C12A/OR2T12A
OR2C15A/OR2T15A
OR2C26A/OR2T26A
OR2C40A/OR2T40A
IDDSB OR2CxxA (TA = 25 °C, VDD = 5 .0 V)
OR2TxxA (TA = 25 °C, VDD = 3.3 V)
internal oscillator running,
no output loads,
inputs at VDD or GND
(after configuration)
—
—
—
—
—
—
—
—
6.5
7.0
7.7
8.4
9.2
10.0
12.2
16.3
—
—
—
—
—
—
—
—
4.0
4.3
4.8
5.3
5.8
6.3
7.8
10.6
mA
mA
mA
mA
mA
mA
mA
mA
Standby Current:
OR2C04A/OR2T04A
OR2C06A/OR2T06A
OR2C08A/OR2T08A
OR2C10A/OR2T10A
OR2C12A/OR2T12A
OR2C15A/OR2T15A
OR2C26A/OR2T26A
OR2C40A/OR2T40A
IDDSB OR2CxxA (TA = 25 °C, VDD = 5.0 V)
OR2TxxA (TA = 25 °C, VDD = 3.3 V)
internal oscillator stopped,
no output loads,
inputs at VDD or GND
(after configuration)
—
—
—
—
—
—
—
—
1.5
2.0
2.7
3.4
4.2
5.0
7.2
11.3
—
—
—
—
—
—
—
—
1.0
1.3
1.8
2.3
2.8
3.3
4.8
7.6
mA
mA
mA
mA
mA
mA
mA
mA
Data Retention Voltage VDR TA = 25 °C 2.3 — 2.3 — V
Input Capa cit anc e CIN OR2CxxA (TA = 25 °C, VDD = 5.0 V)
OR2TxxA (TA = 25 °C, VDD = 3.3 V)
Test frequency = 1 MHz
—9— 9pF
Output Capacitance COUT OR2CxxA (TA = 25 °C, VDD = 5.0 V)
OR2TxxA (TA = 25 °C, VDD = 3.3 V)
Test frequency = 1 MHz
—9— 9pF
DONE Pull-up Resistor* RDONE — 100k — 100k — Ω
M3, M2, M1, and M0
Pull-up Resistors* RM— 100k — 100k — Ω
I/O Pad Static Pull-up
Current* IPU OR2CxxA (VDD = 5.25 V, VIN = VSS,
TA = 0 °C)
OR2TxxA (VDD = 3.6 V, VIN = VSS,
TA = 0 °C)
14.4 50.9 14.4 50.9 µA
I/O Pad Static Pull-down
Current IPD OR2CxxA (VDD = 5.25 V, VIN = VSS,
TA = 0 °C)
OR2TxxA (VDD = 3.6 V, VIN = VSS,
TA = 0 °C)
26 103 26 103 µA
I/O Pad Pull-up Resistor* RPU VDD = All, VIN = VSS, TA = 0 ° C 100k — 100k — Ω
I/O Pad Pull-down
Resistor RPD VDD = All, VIN = VDD, TA = 0 °C 50k — 50k — Ω
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 131
Electrical Characteristics (continued)
* On the OR2TxxB dev ices, the pull-up resistor will ex ter nally pull the pin to a level 1.0 V below VDD.
Table 31B. OR2TxxB Electrical Characteristics
OR2TxxB Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2TxxB I ndustrial: VDD = 3.0 V to 3. 6 V, –40 °C ≤ TA ≤ +85 °C.
Parameter Symbol Test Conditions OR2TxxB Unit
Min Max
Input Voltage:
High
Low VIH
VIL
Inpu t conf igu red as C MOS 80% VDD
GND – 0.5 VDD + 0.3
15% VDD V
V
Output Voltage:
High
Low VOH
VOL VDD = min, IOH = 6 mA or 3 mA
VDD = min, IOL = 12 mA or 6 mA 2.4
——
0.4 V
V
Input Leakage Current ILVDD = max, VIN = VSS or VDD –10 10 µA
Standby Current:
OR2T15B
OR2T40B
IDDSB OR2TxxB (TA = 25 °C, VDD = 3.3 V)
internal oscil lator run ning,
no output l oads,
inputs at VDD or GND
(after configuration)
—
—5.5
8.0 mA
mA
Standby Current:
OR2T15B
OR2T40B
IDDSB OR2TxxB (TA = 25 °C, VDD = 3.3 V)
internal oscillator stopped,
no output l oads,
inputs at VDD or GND
(after configuration)
—
—2.0
4.5 mA
mA
Data Retention Voltage VDR TA = 25 °C 2.3 — V
Input Capacitance CIN OR2TxxB (TA = 25 °C, VDD = 3.3 V)
Test frequency = 1 MHz —8pF
Output Capacitance COUT OR2TxxB (TA = 25 °C, VDD = 3.3 V)
Test frequency = 1 MHz —8pF
DONE Pull-up Resistor* RDONE — 100k — Ω
M3, M2, M1, and M0
Pull-up Resistors* RM— 100k — Ω
I/O Pad Static Pull-up
Current* IPU VDD = 3.6 V, VIN = VSS, TA = 0 °C 14.4 50.9 µA
I/O Pad Static Pull-down Cur-
rent IPD VDD = 3.6 V, VIN = VDD, TA = 0 ° C 26 103 µA
I/O Pad Pull-up Resistor* RPU VDD = all, VIN = VSS, TA = 0 °C 100k — Ω
I/O Pad Pull-down
Resistor RPD VDD = all, VIN = VDD, TA = 0 °C 50k — Ω
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
132 Lucent Technologies Inc.
Timing Characteristics
Note: Speed grades of -5, -6, and -7 are for OR2TxxA de vi ces only.
Table 32A. OR2CxxA and OR2TxxA Combinatorial PFU Timing Characteristics
OR2CxxA Commercial: VDD = 5.0 V ± 5%, 0 °C ≤ TA ≤ 70 °C; OR2CxxA Industrial: VDD = 5. 0 V ± 10%, –40 ° C ≤ TA ≤ +85 °C.
OR2TxxA Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; O R2Tx xA In dustrial: VDD = 3.0 V to 3.6 V, –40 °C ≤ TA ≤ +85 °C.
Parameter Symbol Speed
Unit
-2 -3 -4 -5 -6 -7
Min Max Min Max Min Max Min Max Min Max Min Max
Combinatorial Delays
(TJ = +85 °C, VDD = min) :
Four Input Variables (A[4:0],
B[4:0] to F[3:0])
Five Input Variables (A[4:0],
B[4:0] to F3, F0)
PFUMUX (A[4:0], B[4:0] to F1)
PFUMUX (C0 to f1)
PFUNAND (A[4:0], B[4:0] to F2)
PFUNAND (C0 to F2)
PFUXOR (A[4:0], B[4:0] to F1)
PFUXOR (C0 to F1)
F4*_DEL
F5*_DEL
MUX_DEL
C0MUX_DEL
ND_DEL
C0ND_DEL
XOR_DEL
C0XOR_DEL
—
—
—
—
—
—
—
—
4.0
4.1
4.7
3.0
4.7
2.7
5.6
3.1
—
—
—
—
—
—
—
—
2.8
2.9
3.8
2.2
4.0
2.2
4.5
2.2
—
—
—
—
—
—
—
—
2.1
2.2
3.2
1.9
3.3
1.8
3.8
2.0
—
—
—
—
—
—
—
—
1.7
1.8
2.6
1.5
2.7
1.5
3.1
1.6
—
—
—
—
—
—
—
—
1.4
1.4
1.9
1.1
1.8
1.0
2.3
1.1
—
—
—
—
—
—
—
—
1.3
1.3
1.8
1.0
1.7
0.8
2.1
1.0
ns
ns
ns
ns
ns
ns
ns
ns
Table 32B. OR2TxxB Combinatorial PFU Timing Characteristics
OR2TxxB Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2TxxB Industrial: VDD = 3.0 V to 3.6 V, –4 0 ° C ≤ TA ≤ +85 °C.
Parameter Symbol Speed
Unit
-7 -8
Min Max Min Max
Combinatorial Delays
(TJ = +85 °C, VDD = min) :
Four Input Variables (A[4:0],
B[4:0] to F[3:0])
Five Input Variables (A[4:0],
B[4:0] to F3, F0)
PFUMUX (A[4:0], B[4:0] to F1)
PFUMUX (C0 to F1)
PFUNAND (A[4:0], B[4:0] to F2)
PFUNAND (C0 to F2)
PFUXOR (A[4:0], B[4:0] to F1)
PFUXOR (C0 to F1)
F4*_DEL
F5*_DEL
MUX_DEL
C0MUX_DEL
ND_DEL
C0ND_DEL
XOR_DEL
C0XOR_DEL
—
—
—
—
—
—
—
—
1.3
1.3
2.2
1.4
2.1
1.2
2.5
1.3
—
—
—
—
—
—
—
—
1.0
1.0
1.8
1.0
1.7
0.9
2.0
1.0
ns
ns
ns
ns
ns
ns
ns
ns
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 133
Timing Characteristics (continued)
5-4633(F).a
C = controlled by configuration RAM.
Notes:
The parameters MUX_DEL, XOR_DEL, and ND_DEL include the delay through the LUT in F5A/F5B modes.
See Table 41 for an ex planation of FDBK_DEL and OMUX_DEL.
Figure 54. Combinatorial PFU Timing
A[4:0], B[ 4:0]
A[4:0], B[ 4:0]
A[4:0], B[ 4:0]
F4*_DEL
(LUT)
PFU
4
F5*_DEL
(LUT) 2
(LUT) 2
C0
MUX_DEL
C
F[3:0]
F3, F0
F1
F2
O[4:0]
FDBK_DEL
XSW LINES
OUTPUT MUX
OMUX_DEL
C0MUX_DEL, C0XOR_DEL, C0ND_DEL
XOR_DEL
ND_DEL
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
134 Lucent Technologies Inc.
Timing Characteristics (continued)
1.The input buffers contain a program mable delay to allow the hold time vs. the ex ter nal clock pin to be equal to 0.
Note: Speed grades of -5, -6, and -7 are for OR2TxxA de vi ces only.
Table 33A. OR2CxxA and OR2TxxA Sequential PFU Timing Characteristics
OR2CxxA Commercial: VDD = 5.0 V ± 5%, 0 °C ≤ TA ≤ 70 °C; OR2CxxA Industrial: VDD = 5. 0 V ± 10%, –40 ° C ≤ TA ≤ +85 °C.
OR2TxxA Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; O R2Tx xA In dustrial: VDD = 3.0 V to 3.6 V, –40 °C ≤ TA ≤ +85 °C.
Parameter Symbol
Speed
Unit
-2 -3 -4 -5 -6 -7
Min Max Min Max Min Max Min Max Min Max Min Max
Input Requirements
Clock Low Time TCL 3.2 — 2.5 — 2.0 — 1.8 — 1.7 — 1.6 — ns
Clock High Time TCH 3.2 — 2.5 — 2.0 — 1.8 — 1.7 — 1.6 — ns
Global S/R Pulse Width (GSRN) TRW 2.8 — 2.5 — 2.0 — 1.8 — 1.7 — 1.6 — ns
Local S/R Pulse Width TPW 3.0 — 2.5 — 2.0 — 1.8 — 1.7 — 1.6 — ns
Combinatorial Setup Times (TJ = 85 °C,
VDD = min ):
Four Input Variables to Clock
(A[4:0], B[4:0] to CK)
Fiv e Input Variables to Cloc k
(A[4:0], B[4:0] to CK)
PFUMUX to Clock (A[4:0], B[4:0] to CK )
PFUMUX to Clock (C0 to CK)
PFUNAND to Clock (A[4:0], B[4:0] to CK)
PFUNAND to Clock (C0 to CK)
PFUXOR to Clock (A[4:0], B[4:0] to CK)
PFUXOR to Clock (C0 to CK)
Data In to Clock (WD[3:0] to CK)
Clock Enable to Clock (CE to CK)
Local Set/Reset (synchronous ) (LSR to CK)
Data Select to Clock ( SEL to CK)
Pad Direct In
F4*_SET
F5*_SET
MUX_SET
C0MUX_SET
ND_SET
C0ND_SET
XOR_SET
C0XOR_SET
D*_SET
CKEN_SET
LSR_SET
SELECT_SET
PDIN_SET
2.4
2.5
3.9
1.5
3.9
1.7
4.8
1.6
0.5
1.6
1.7
1.9
0.0
—
—
—
—
—
—
—
—
—
—
—
—
—
1.7
1.9
2.9
1.2
2.9
1.2
3.6
1.2
0.1
1.2
1.4
1.5
0.0
—
—
—
—
—
—
—
—
—
—
—
—
—
1.3
1.3
2.3
0.9
2.2
0.6
3.0
0.9
0.1
1.0
1.3
1.4
0.0
—
—
—
—
—
—
—
—
—
—
—
—
—
1.1
1.2
2.1
0.8
2.0
0.5
2.7
0.8
0.0
0.9
1.2
1.3
0.0
—
—
—
—
—
—
—
—
—
—
—
—
—
1.0
1.0
1.6
0.7
1.7
0.5
2.1
0.7
0.1
0.9
1.1
1.2
0.0
—
—
—
—
—
—
—
—
—
—
—
—
—
0.9
0.9
1.5
0.6
1.6
0.5
2.0
0.6
0.1
0.6
0.8
1.0
0.0
—
—
—
—
—
—
—
—
—
—
—
—
—
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Combinatorial Hold Times (TJ = all, VDD = all):
Data In (WD[3:0] from CK)
Clock Enable (CE from CK)
Local Set/Reset (synchronous) (LSR from CK)
Data Select (sel from CK)
Pad Direct In Hold (DIA[3:0], DIB[3:0] to CK)1
All Others
D*_HLD
CKEN_HLD
LSR_HLD
SELECT_HLD
PDIN_HLD
—
0.6
0.6
0.0
0.0
1.5
0.0
—
—
—
—
—
—
0.4
0.4
0.0
0.0
1.4
0.0
—
—
—
—
—
—
0.4
0.0
0.0
0.0
1.0
0.0
—
—
—
—
—
—
0.4
0.0
0.0
0.0
0.9
0.0
—
—
—
—
—
—
0.3
0.0
0.0
0.0
0.8
0.0
—
—
—
—
—
—
0.3
0.0
0.0
0.0
0.8
0.0
—
—
—
—
—
—
ns
ns
ns
ns
ns
ns
Output Characteristics
Sequential Delays (TJ = 85 °C, VDD = min):
Local S/R (async) to PFU Out (LSR to Q[3:0])
Global S/R to PFU Out (GSRN to Q[3:0])
Cloc k to PFU Out (CK to Q[3:0])—Register
Cloc k to PFU Out (CK to Q[3:0])—Latch
Transparent Latch (WD[3:0] to Q[3:0])
LSR_DEL
GSR_DEL
REG_DEL
LTCH_DEL
LTCH_DDEL
—
—
—
—
—
4.5
2.9
2.4
2.5
3.5
—
—
—
—
—
3.4
2.3
2.0
2.0
2.7
—
—
—
—
—
3.1
2.0
1.9
1.9
2.5
—
—
—
—
—
2.5
1.6
1.5
1.5
2.0
—
—
—
—
—
2.0
1.3
1.3
1.3
2.0
—
—
—
—
—
1.6
1.2
1.0
1.0
1.8
ns
ns
ns
ns
ns
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 135
Timing Characteristics (continued)
1.The input buffers contain a program mable delay to allow the hold time vs. the ex ter nal clock pin to be equal to 0.
Table 33B. OR2TxxB Sequential PFU Timing Characteristics
OR2TxxB Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2TxxB I ndustrial: VDD = 3.0 V to 3. 6 V, –40 °C ≤ TA ≤
+85 °C.
Parameter Symbol
Speed
Unit
-7 -8
Min Max Min Max
Input Requirements
Clock Low Time TCL 1.7 —1.4 —ns
Clock High Time TCH 1.7 —1.4 —ns
Global S/R Pulse Width (GSRN) TRW 1.7 —1.4 —ns
Local S/R Pulse Width TPW 1.7 —1.4 —ns
Combinatorial Setup Times (TJ = 85 °C,
VDD = min):
Four Input Variables to Clock
(A[4:0], B[4:0] to CK)
Fiv e Input Variables to Cloc k
(A[4:0], B[4:0] to CK)
PFUMUX to Clock (A[4:0], B[4:0] to CK )
PFUMUX to Clock (C0 to CK)
PFUNAND to Clock (A[4:0], B[4:0] to CK)
PFUNAND to Clock (C0 to CK)
PFUXOR to Clock (A[4:0], B[4:0] to CK)
PFUXOR to Clock (C0 to CK)
Data In to Clock (WD[3:0] to CK)
Clock Enable to Clock (CE to CK)
Local Set/Reset (synchronous ) (LSR to CK)
Data Select to Clock (SEL to CK)
Pad Direct In
F4*_SET
F5*_SET
MUX_SET
C0MUX_SET
ND_SET
C0ND_SET
XOR_SET
C0XOR_SET
D*_SET
CKEN_SET
LSR_SET
SELECT_SET
PDIN_SET
1.0
1.0
1.3
1.1
1.0
0.8
1.3
1.1
0.2
1.0
1.0
1.0
0.0
—
—
—
—
—
—
—
—
—
—
—
—
—
0.8
0.8
1.3
0.8
0.8
0.7
1.3
0.8
0.1
0.8
0.8
0.8
0.0
—
—
—
—
—
—
—
—
—
—
—
—
—
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Combinatorial Hold Times (TJ = all, VDD = all):
Data In (WD[3:0] from CK)
Clock Enable (CE from CK)
Local Set/Reset (synchronous) (LSR from CK)
Data Select (SEL from CK)
Pad Direct In Hold (DIA[3:0], DIB[3:0] to CK)1
All Others
D*_HLD
CKEN_HLD
LSR_HLD
SELECT_HLD
PDIN_HLD
—
0.0
0.0
0.0
0.0
0.1
0.0
—
—
—
—
—
—
0.0
0.0
0.0
0.0
0.1
0.0
—
—
—
—
—
—
ns
ns
ns
ns
ns
ns
Output Characteristics
Sequential Delays (TJ = 85 °C, VDD = min):
Local S/R (async) to PFU Out (LSR to Q[3:0])
Global S/R to PFU Out (GSRN to Q[3:0])
Clock to PFU Out (CK to Q[3:0])—Register
Clock to PFU Out (CK to Q[3:0])—Latch
Transparent Latch (WD[3:0] to Q[3:0])
LSR_DEL
GSR_DEL
REG_DEL
LTCH_DEL
LTCH_DDEL
2.2
1.4
1.0
1.0
1.7
—
—
—
—
—
1.8
1.0
1.0
1.0
1.4
—
—
—
—
—
ns
ns
ns
ns
ns
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
136 Lucent Technologies Inc.
Timing Characteristics (continued)
Table 34A. OR2CxxA and OR2TxxA Ripple Mode PFU Timing Characteristics
OR2CxxA Commercial: VDD = 5.0 V ± 5%, 0 °C ≤ TA ≤ 70 °C; OR2CxxA Industrial: VDD = 5. 0 V ± 10%, –40 ° C ≤ TA ≤ +85 °C.
OR2Tx x A C om me rcial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C ; OR 2T xx A Ind us trial: VDD = 3.0 V to 3.6 V, –40 °C ≤ TA ≤ +85 °C.
Parameter Symbol
Speed
Unit
-2 -3 -4 -5 -6 -7
Min Max Min Max Min Max Min Max Min Max Min Max
Ripple Setup Times
(TJ = +85 °C, VDD = min):
Operands to Clock (A[3:0], B[3:0] to CK)
Bitwise Operands to Clock
(A[i], B[i] to CK at F[i])
Carry-in from Fast Carry to Clock
(CIN to CK)
Carry-in from General Routing to Clock
(B4 to CK)
Add/Subtract to Clock (A4 to CK)
RIP_SET
FRIP_SET
CIN_SET
B4_SET
AS_SET
6.7
2.4
4.0
4.0
8.2
—
—
—
—
—
5.0
1.7
3.2
3.2
5.6
—
—
—
—
—
3.7
1.3
1.9
1.9
4.3
—
—
—
—
—
3.3
1.2
1.7
1.7
3.9
—
—
—
—
—
2.8
1.0
1.4
1.4
3.2
—
—
—
—
—
2.5
0.9
1.3
1.3
3.1
—
—
—
—
—
ns
ns
ns
ns
ns
Ripple Hold Times (TJ = all, VDD = all): All TH 0.0 — 0.0 — 0.0 — 0.0 — 0.0 — 0.0 — ns
Ripple Delay s (TJ = 85 °C, VDD = min):
Operands to Carry-out (A[3:0], B[3:0]
to COUT)
Operands to Carry-out (A[3:0], B[3:0]
to O4)
Operands to PFU Out (A[3:0], B[3:0]
to F[3:0])
Bitwise Operands to PFU Out (A[i], B[i]
to F[i])
Carry-in from Fast Carry to Carry-out
(CIN to COUT)
Carry-in from Fast Carry to Carry-out
(CIN to O4)
Carr y-in from Fas t Carry to PFU Out
(CIN to F[3:0])
Carry-in from General Routing to Carry-
out (B4 to COUT)
Carry-in from General Routing to Carry-
out (B4 to O4)
Carry-in from General Routing to PFU Out
(B4 to F[3:0])
Add/Subtract to Carry-out (A4 to COUT)
Add/Subtract to Carry-out (A4 to O4)
Add/Subtract to PFU Out (A4 to F[3:0])
RIP_CODEL
RIP_O4DEL
RIP_DEL
FRIP_DEL
CIN_CODEL
CIN_O4DEL
CIN_DEL
B4_CODEL
B4_O4DEL
B4_DEL
AS_CODEL
AS_O4DEL
AS_DEL
—
—
—
—
—
—
—
—
—
—
—
—
—
5.4
6.9
8.2
4.0
1.9
3.5
5.6
1.9
3.5
5.6
6.1
7.6
9.7
—
—
—
—
—
—
—
—
—
—
—
—
—
3.8
4.8
6.0
2.8
1.6
2.6
4.2
1.6
2.6
4.2
4.5
5.6
6.8
—
—
—
—
—
—
—
—
—
—
—
—
—
3.3
4.2
4.7
2.1
1.1
2.1
2.9
1.1
2.1
2.9
3.9
4.9
5.3
—
—
—
—
—
—
—
—
—
—
—
—
—
2.6
3.4
3.8
1.7
0.9
1.7
2.3
0.9
1.7
2.3
3.1
3.9
4.3
—
—
—
—
—
—
—
—
—
—
—
—
—
2.1
2.6
3.2
1.6
0.7
1.3
2.2
0.7
1.3
2.2
2.5
3.1
3.5
—
—
—
—
—
—
—
—
—
—
—
—
—
1.8
2.4
2.8
1.5
0.6
1.1
1.7
0.6
1.1
2.1
2.3
2.8
3.1
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Notes:
The new 4 x 1 multiplier and 4-bit comparator submodes use the appropriate ripple mode timing shown above.
Speed grades of -5, -6, and -7 are for OR2TxxA devices only.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 137
Timing Characteristics (continued)
Table 34B. OR2TxxB Ripple Mode PFU Timing Characteristics
OR2TxxB Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2TxxB I ndustrial: VDD = 3.0 V to 3. 6 V, –40 °C ≤ TA ≤
+85 °C.
Parameter Symbol
Speed
Unit
-7 -8
Min Max Min Max
Ripple Setup Times
(TJ = 85 °C, VDD = min):
Operands to Clock (A[3:0], B[3:0] to CK)
Bitwise Operands to Clock
(A[i], B[i] to CK at F[i])
Carry-in from Fast Carry to Clock
(CIN to CK)
Carry-in from General Routing to Clock
(B4 to CK)
Add/Subtract to Clock (A4 to CK)
RIP_SET
FRIP_SET
CIN_SET
B4_SET
AS_SET
2.4
1.1
1.6
1.0
2.9
—
—
—
—
—
1.9
0.9
1.3
0.8
2.3
—
—
—
—
—
ns
ns
ns
ns
ns
Ripple Hold Times (TJ = all, VDD = all): All TH ns
Ripple Delay s (TJ = 85 °C, VDD = min):
Operands to Carry-out (A[3:0], B[3:0]
to COUT)
Operands to Carry-out (A[3:0], B[3:0]
to O4)
Operands to PFU Out (A[3:0], B[3:0]
to F[3:0])
Bitwise Operands to PFU Out (A[i], B[i]
to F[i])
Carry-in from Fast Carry to Carry-out
(CIN to COUT)
Carry-in from Fast Carry to Carry-out
(CIN to O4)
Carr y-in from Fas t Carry to PFU Out
(CIN to F[3:0])
Carry-in from General Routing to Carry-
out (B4 to COUT)
Carry-in from General Routing to Carry-
out (B4 to O4)
Carry-in from General Routing to PFU Out
(B4 to F[3:0])
Add/Subtract to Carry-out (A4 to COUT)
Add/Subtract to Carry-out (A4 to O4)
Add/Subtract to PFU Out (A4 to F[3:0])
RIP_CODEL
RIP_O4DEL
RIP_DEL
FRIP_DEL
CIN_CODEL
CIN_O4DEL
CIN_DEL
B4_CODEL
B4_O4DEL
B4_DEL
AS_CODEL
AS_O4DEL
AS_DEL
2.2
3.0
3.1
1.4
0.7
1.4
1.9
0.7
1.4
1.9
2.7
3.4
3.6
—
—
—
—
—
—
—
—
—
—
—
—
—
1.8
2.4
2.5
1.1
0.6
1.2
1.5
0.6
1.2
1.5
2.2
2.8
2.9
—
—
—
—
—
—
—
—
—
—
—
—
—
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Notes: The new 4 x 1 multiplier and 4-bit comparator submodes use the appropriate ripple mode timing shown abo ve.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
138 Lucent Technologies Inc.
Timing Characteristics (continued)
Note: Speed grades of -5, -6, and -7 are for OR2TxxA de vi ces only.
5-3226(F).r4
Figure 55. Read Operation—Flip-Flop Bypass
5-3227(F).r4
Figure 56. Read Operation—LUT Memory Loading Flip-Flops
Table 35A. OR2CxxA and OR2TxxA Asynchronous Memory Read Characteristics (MA/MB Modes)
OR2CxxA Commercial: VDD = 5.0 V ± 5%, 0 °C ≤ TA ≤ 70 °C; OR2CxxA Industrial: VDD = 5. 0 V ± 10%, –40 ° C ≤ TA ≤ +85 °C.
OR2TxxA Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; O R2 Tx xA Industrial : VDD = 3.0 V to 3.6 V, –4 0 °C ≤ TA ≤ +85 °C.
Parameter Symbol
Speed
Unit
-2 -3 -4 -5 -6 -7
Min Max Min Max Min Max Min Max Min Max Min Max
Read Operation (TJ = 85 °C, VDD = min):
Read Cycle Time
Data Valid after Address (A[3:0], B[3:0] to F[3:0]) TRC
MEM*_ADEL 5.1
——
4.0 3.6
——
2.8 2.7
——
2.1 2.4
——
1.7 2.3
——
1.4 2.0
——
1.3 ns
ns
Read Operation, Clocking Data into Latch/Flip-flop
(TJ = 85 °C, VDD = min):
Address to Clock Setup Time (A[3:0], B[3:0] to CK)
Clock to PFU Out (CK to Q[3:0])—Register MEM*_ASET
REG_DEL 2.4
——
2.4 1.8
——
2.0 1.2
——
1.9 1.1
——
1.5 1.0
——
1.3 1.0
——
1.0 ns
ns
Table 35B. OR2TxxB Asynchronous Memory Read Characteristics (MA/MB Modes)
OR2TxxB Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2TxxB Industrial: VDD = 3.0 V to 3.6 V, –4 0 ° C ≤ TA ≤ +85 °C.
Parameter Symbol
Speed
Unit
-7 -8
Min Max Min Max
Read Operation (TJ = 85 °C, VDD = min):
Read Cycle Time
Data Valid after Address (A[3:0], B[3:0] to F[3:0]) TRC
MEM*_ADEL 1.9
——
1.3 1.8
——
1.0 ns
ns
Read Operation, Clocking Data into Latch/Flip-flop
(TJ = 85 °C, VDD = min):
Address to Clock Setup Time (A[3:0], B[3:0] to CK)
Clock to PFU Out (CK to Q[3:0])—Register MEM*_ASET
REG_DEL 0.9
——
1.0 0.8
——
1.0 ns
ns
A[3:0], B[3:0]
F[3:0]
MEM*_ADEL
TRC
A[3:0], B[3:0]
CK
MEM*_ASET
REG_DEL
Q[3:0]
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 139
Timing Characteristics (continued)
Note: Speed grades of -5, -6, and -7 are for OR2TxxA de vi ces only.
Table 36A. OR2CxxA and OR2TxxA Asynchronous Memory Write Characteristics (MA/MB Modes)
OR2Cx xA Com me rcial: VDD = 5.0 V ± 5%, 0 °C ≤ TA ≤ 70 °C; OR2CxxA Industrial: VDD = 5.0 V ± 10%, –40 °C ≤ TA ≤ +85 °C .
OR2TxxA Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2TxxA Industrial: VDD = 3.0 V to 3.6 V, –40 °C ≤ TA ≤
+85 °C.
Parameter Symbol
Speed
Unit
-2 -3 -4 -5 -6 -7
Min Max Min Max Min Max Min Max Min Max Min Max
Write Operation (TJ = 85 °C, VDD = min):
Write Cycle Time
Write Enable (WREN) Pulse Width (A4/ B4) TWC
TPW 9.3
3.0 —
—7.8
2.5 —
—6.3
2.0 —
—5.7
1.8 —
—5.2
1.7 —
—5.1
1.6 —
—ns
ns
Setup Time (TJ = 85 °C , VDD = min):
Address to WREN (A[3:0]/B[3:0] to A4/B4)
Data to WREN (WD[3:0] to A4/B4)
Address to WPE (A[3:0]/B[3:0] to C0)
Data to WPE (WD[3:0] to C0)
WPE to W R EN ( C 0 to A4 /B4)
MEM*_AWRSET
MEM*_DWRSET
MEM*_APWRSET
MEM*_DPWRSET
MEM*_WPESET
0.1
0.0
0.0
0.0
2.5
—
—
—
—
—
0.1
0.0
0.0
0.0
2.0
—
—
—
—
—
0.0
0.0
0.0
0.0
1.5
—
—
—
—
—
0.0
0.0
0.0
0.0
1.4
—
—
—
—
—
0.0
0.0
0.0
0.0
1.1
—
—
—
—
—
0.0
0.0
0.0
0.0
1.1
—
—
—
—
—
ns
ns
ns
ns
ns
Hold Time (TJ = all, VDD = all):
Address from WREN (A[3:0]/B[3:0] from A4/B4)
Data from WREN (WD[3:0] from A4/B4)
Address from WPE (A[3:0/B[3:0] to C0)
Data from WPE (WD[3:0] to C0)
WPE from WREN (C0 from A4/B4)
MEM*_WRAHLD
MEM*_WRDHLD
MEM*_PWRAHLD
MEM*_PWRDHLD
MEM*_WPEHLD
2.4
2.4
3.8
3.9
0.0
—
—
—
—
—
1.7
2.0
3.3
3.4
0.0
—
—
—
—
—
1.8
1.9
2.8
2.9
0.0
—
—
—
—
—
1.6
1.5
2.5
2.6
0.0
—
—
—
—
—
1.6
1.6
2.4
2.4
0.0
—
—
—
—
—
1.5
1.6
2.3
2.3
0.0
—
—
—
—
—
ns
ns
ns
ns
ns
Table 36B. OR2TxxB Asynchronous Memory Write Characteristics (MA/MB Modes)
OR2TxxB Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2TxxB I ndustrial: VDD = 3.0 V to 3. 6 V, –40 °C ≤ TA ≤
+85 °C.
Parameter Symbol
Speed
Unit
-7 -8
MinMaxMinMax
Write Operation (TJ = 85 °C, VDD = min):
Write Cycle Time
Write Enable (WREN) Pulse Width (A4/B4) TWC
TPW 5.1
1.7 —
—4.2
1.4 —
—ns
ns
Setu p Time (TJ = 85 °C, VDD = min):
Address to WREN (A[3:0]/B[3:0] to A4/B4)
Data to WREN (WD[3:0] to A4/B4)
Address to WPE (A[3:0]/B[3:0] to C0)
Data to WPE (WD[3:0] to C0)
WPE to WREN (C0 to A4/B4)
MEM*_AWRSET
MEM*_DWRSET
MEM*_APWRSET
MEM*_DPWRSET
MEM*_WPESET
0.0
0.0
0.0
0.0
1.0
—
—
—
—
—
0.0
0.0
0.0
0.0
0.8
—
—
—
—
—
ns
ns
ns
ns
ns
Hold Time (TJ = all, VDD = all):
Address from WREN (A[3:0]/B[3:0] from A4/B4)
Data from WREN (WD[3:0] from A4/B4)
Address from WPE (A[3:0/B[3:0] to C0)
Data from WPE (WD[3:0] to C0)
WPE from WREN (C0 from A4/B4)
MEM*_WRAHLD
MEM*_WRDHLD
MEM*_PWRAHLD
MEM*_PWRDHLD
MEM*_WPEHLD
0.9
1.6
2.3
2.3
0.0
—
—
—
—
—
0.7
1.3
1.9
1.9
0.0
—
—
—
—
—
ns
ns
ns
ns
ns
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
140 Lucent Technologies Inc.
Timing Characteristics (continued)
5-3228(F).r6
Figure 57. Write Operati on
A[3:0], B[3:0]
WD[3:0]
MEM*_APWRSET
TWC
C0 (WPE)
MEM*_PWRAHLD
MEM*_WPEHLD
TPW
MEM*_WPESET
A4, B4 (WREN)
MEM*_WRAHLD
MEM*_PWRDHLDMEM*_DPWRSET
MEM*_AWRSET
MEM*_DWRSET MEM*_WRDHLD
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 141
Timing Characteristics (continued)
Note: Speed grades of -5, -6, and -7 are for OR2TxxA de vi ces only.
Table 37A. OR2CxxA and OR2TxxA Asynchronous Memory Read During Write Operation (MA/MB Modes)
OR2Cx xA Com me rcial: VDD = 5.0 V ± 5%, 0 °C ≤ TA ≤ 70 °C; OR2CxxA Industrial: VDD = 5.0 V ± 10%, –40 °C ≤ TA ≤ +85 °C .
OR2TxxA Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2TxxA Industrial: VDD = 3.0 V to 3.6 V, –40 °C ≤ TA ≤
+85 °C.
Parameter Symbol
Speed
Unit
-2 -3 -4 -5 -6 -7
Min Max Min Max Min Max Min Max Min Max Min Max
Read During Write Operation
(TJ = 85 °C, VDD = min):
Write Enable (WREN) to PFU Output Delay
(A4/B4 to F[3:0])
Write-port Enable (WPE) to PFU Output
Delay (C0 to F[3:0])
Data to PFU Output Delay (WD[3:0] to F[3:0])
MEM*_WRDEL
MEM*_PWRDEL
MEM*_DDEL
—
—
—
7.0
9.0
5.0
—
—
—
4.9
6.4
3.6
—
—
—
4.8
5.8
3.1
—
—
—
3.9
4.7
2.5
—
—
—
4.0
4.7
2.5
—
—
—
3.9
4.5
2.2
ns
ns
ns
Table 37B. OR2TxxB Asynchronous Memory Read During Write Operation (MA/MB Modes)
OR2TxxB Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2TxxB I ndustrial: VDD = 3.0 V to 3. 6 V, –40 °C ≤ TA ≤
+85 °C.
Parameter Symbol
Speed
Unit
-7 -8
Min Max Min Max
Read During Write Operation
(TJ = +85 °C, VDD = min):
Write Enable (WREN) to PFU Output Delay
(A4/B4 to F[3:0])
Write-port Enable (WPE) to PFU Output
Delay (C0 to F[3:0])
Data to PFU Output Delay (WD[3:0] to F[3:0])
MEM*_WRDEL
MEM*_PWRDEL
MEM*_DDEL
—
—
—
4.5
4.6
2.7
—
—
—
3.9
4.0
2.4
ns
ns
ns
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
142 Lucent Technologies Inc.
Timing Characteristics (continued)
5-3229(F).r6
Figure 58. Read During Write
A[3:0], B[3:0]
A4, B4 (WRE N)
WD[3:0]
F[3:0]
WD[3:0]
F[3:0]
TPW
MEM*_WRDEL
MEM*_DDEL
MEM*_WRDEL
DATA STABLE
DURING
WREN AND WPE
DATA CHANGING
DURING
WREN AND WPE
CO (WPE)
MEM*_PWRDEL
MEM*_PWRDEL
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 143
Timing Characteristics (continued)
Note: Speed grades of -5, -6, and -7 are for OR2TxxA de vi ces only.
Table 38A. OR2CxxA and OR2TxxA Asynchronous Memory Read During Write, Clocking Data into Latch/
Flip-Flop (MA/MB Modes)
OR2CxxA Commercial : VDD = 5.0 V ± 5% , 0 °C ≤ TA ≤ 70 °C; OR2Cxx A Ind us trial: V DD = 5.0 V ± 10% , –4 0 °C ≤ TA ≤ +85 °C .
OR2TxxA Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2TxxA Industrial: VDD = 3.0 V to 3.6 V, –40 °C ≤ TA ≤
+85 °C.
Parameter Symbol
Speed
Unit
-2 -3 -4 -5 -6 -7
Min Max Min Max Min Max Min Max Min Max Min Max
Setup Time (TJ = 85 °C , VDD = min):
Address to Clock (A[3:0], B[3:0] to CK)
Write Enab le (WREN) to Clock (A4/B4 to CK)
Write-port Enable (WPE) to Clock (C0 to CK)
Data (WD[3:0] to CK)
MEM*_ASET
MEM*_WRSET
MEM*_PWRSET
MEM*_DSET
2.4
5.4
7.4
3.5
—
—
—
—
1.8
4.4
5.9
2.6
—
—
—
—
1.2
3.8
4.8
2.6
—
—
—
—
1.1
3.4
4.3
2.3
—
—
—
—
1.0
3.1
4.0
2.2
—
—
—
—
1.0
3.0
3.9
2.1
—
—
—
—
ns
ns
ns
ns
Hold Time (TJ = All, VDD = All): All TH 0.0 — 0.0 — 0.0 — 0.0 — 0.0 — 0.0 — ns
Clock to PFU Out (CK to Q[3:0])—Register REG_DEL — 2.4 — 2.0 — 1.9 — 1.5 — 1.3 — 1.0 ns
Table 38B. OR2TxxB Asynchronous Memory Read During Write, Clocking Data into Latch/Flip-Flop
(MA/MB Modes)
OR2TxxB Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2TxxB I ndustrial: VDD = 3.0 V to 3. 6 V, –40 °C ≤ TA ≤
+85 °C.
Parameter Symbol
Speed
Unit
-7 -8
Min Max Min Max
Setu p Time (TJ = 85 °C, VDD = min):
Address to Clock (A[3:0], B[3:0] to CK)
Write Enable (WREN) to Clock (A4/B4 to CK)
Write-port Enable (WPE) to Clock (C0 to CK)
Data (WD[3:0] to CK)
MEM*_ASET
MEM*_WRSET
MEM*_PWRSET
MEM*_DSET
0.9
2.9
3.7
2.0
—
—
—
—
0.8
2.5
3.2
1.7
—
—
—
—
ns
ns
ns
ns
Hold Time (TJ = all, VDD = all): All TH 0.0 — 0.0 — ns
Clock to PFU Out (CK to Q[3:0])—Register REG_DEL — 1.0 — 1.0 ns
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
144 Lucent Technologies Inc.
Timing Characteristics (continued)
5-3230(F).r6
Figure 59. Read During Write—Clocking Data into Flip-Flop
A[3:0], B[3:0]
A4, B4 (WREN)
WD[3:0]
CK
TPW
MEM*_DSET
Q[3:0]
MEM*_ASET
REG_DEL
C0 (WPE)
MEM*_PWRSET
MEM*_WRSET
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 145
Timing Characteristics (continued)
1. Readback of the configuration bit stream when simultaneously writing to a PFU in either SSPM fast mode or SDPM fast mode is not allowed.
2. Because the setup time of data into the latches/FFs is less than 0 ns, data written into the RAM can be loaded into a latch/FF in the same
PFU on the next opposite clock edge (one-half clock per iod).
Note: Speed grades of -5, -6, and -7 are for OR2TxxA de vi ces only.
Table 39A. OR2CxxA and OR2TxxA Synchronous Memory Write Characteristics (SSPM and SDPM Modes)
OR2Cx xA Co mm ercia l: V DD = 5.0 V ± 5%, 0 °C ≤ TA ≤ 70 °C; O R2C xx A In dus trial: VDD = 5.0 V ± 1 0%, –40 °C ≤ TA ≤ +85 °C.
OR2TxxA Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2TxxA Industrial: VDD = 3.0 V to 3.6 V, –40 °C ≤ TA ≤
+85 °C.
Parameter Symbol
Speed Unit
-2 -3 -4 -5 -6 -7
Min Max Min Max Min Max Min Max Min Max Min Max
Write Operation for Fast-RAM Mode1:
Maximum Frequency
Clock Low Time
Clock High Time
Clock t o Data Valid (CK to F[3:0])2
FFSCK
TFSCL
TFSCH
FMEMS_DEL
38.2
13.1
13.1
—
—
—
—
9.0
52.6
9.5
9.5
—
—
—
—
7.4
83.3
6.0
6.0
—
—
—
—
6.2
90.9
5.5
5.5
—
—
—
—
5.0
92.6
5.4
5.4
—
—
—
—
5.3
96.2
5.2
5.2
—
—
—
—
5.2
MHz
ns
ns
ns
Write Operation for Normal RAM Mode:
Maximum Frequency
Clock Low Time
Clock High Time
Clock t o Data Valid (CK to F[3:0])
FSCK
TSCL
TSCH
MEMS_DEL
24.3
20.6
20.6
—
—
—
—
10.9
33.3
15.0
15.0
—
—
—
—
8.6
52.6
9.5
9.5
—
—
—
—
7.5
58.0
8.5
8.5
—
—
—
—
6.0
58.8
8.5
8.5
—
—
—
—
6.4
59.8
8.4
8.4
—
—
—
—
5.9
MHz
ns
ns
ns
Write Operation Setup Time:
Address to Clock (A[3:0]/B[3:0] to CK)
Data to Clock (WD[3:0] t o CK)
Write Enabl e (WREN) to Clock
(A4 to CK)
Write-port Enable (WPE) to Clock
(C0 to CK)
MEMS_ASET
MEMS_DSET
MEMS_WRSET
MEMS_PWRSET
0.0
0.0
0.0
0.0
—
—
—
—
0.0
0.0
0.0
0.0
—
—
—
—
0.0
0.0
0.0
0.0
—
—
—
—
0.0
0.0
0.0
0.0
—
—
—
—
0.0
0.0
0.0
0.0
—
—
—
—
0.0
0.0
0.0
0.0
—
—
—
—
ns
ns
ns
ns
Write Operation Hold Time:
Address to Clock (A[3:0]/B[3:0] to CK)
Data to Clock (WD[3:0] t o CK)
Write Enabl e (WREN) to Clock
(A4 to CK)
Write-port Enable (WPE) to Clock
(C0 to CK)
MEMS_AHLD
MEMS_DHLD
MEMS_WRHLD
MEMS_PWRHLD
3.8
3.8
3.8
3.3
—
—
—
—
3.0
3.0
3.0
2.3
—
—
—
—
2.2
2.2
2.2
1.5
—
—
—
—
2.0
2.0
2.0
1.4
—
—
—
—
1.9
1.9
1.9
1.9
—
—
—
—
1.8
1.8
1.8
1.2
—
—
—
—
ns
ns
ns
ns
Table 39.B OR2TxxB Synchronous Memory Write Characteristics (SSPM and SDPM Modes)
OR2TxxB Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2Txx B Industrial: VDD = 3.0 V to 3.6 V, –40 °C ≤ TA ≤ +8 5 °C.
Parameter Symbol
Speed Unit
-7 -8
Min Max Min Max
Write Operation fo r Fast-RAM Mode1:
Maximum Frequenc y
Clock Low Time
Clock High Time
Clock to Data Valid (CK to F[3:0])2
FFSCK
TFSCL
TFSCH
FMEMS_DEL
97.7
5.1
5.1
—
—
—
—
5.1
112.4
4.5
4.5
—
—
—
—
4.5
MHz
ns
ns
ns
Write Operation fo r Normal RAM Mode:
Maximum Frequenc y
Clock Low Time
Clock High Time
Clock to Data Valid (CK to F[3:0])
FSCK
TSCL
TSCH
MEMS_DEL
60.8
8.2
8.2
—
—
—
—
5.1
69.9
7.2
7.2
—
—
—
—
4.5
MHz
ns
ns
ns
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
146 Lucent Technologies Inc.
1. Readback of the configurat ion bit stream when simultaneously writing to a PFU in either SSPM fast mode or SDPM f ast mode is not allowed.
2. Because the setup time of data into the latches/FFs is less than 0 ns, data written into the RAM can be loaded into a latch/FF in the same
PFU on the next opposite clock edge (one-half clock per iod).
Note: Speed grades of -5, -6, and -7 are for OR2TxxA de vi ces only.
5-4621(F).a
Figure 60. Synchronous Memory Write Characteristics
Write Operation Setup Time:
Address to Clock (A[3:0]/B[3:0] to CK)
Data to Clock (WD[3:0] to CK)
Write Enable (WREN) to Clock
(A4 to CK)
Write-port Enable (WPE) to Clock
(C0 to CK)
MEMS_ASET
MEMS_DSET
MEMS_WRSET
MEMS_PWRSET
0.0
0.0
0.0
0.0
—
—
—
—
0.0
0.0
0.0
0.0
—
—
—
—
ns
ns
ns
ns
Write Operation Hold Time:
Address to Clock (A[3:0]/B[3:0] to CK)
Data to Clock (WD[3:0] to CK)
Write Enable (WREN) to Clock
(A4 to CK)
Write-port Enable (WPE) to Clock
(C0 to CK)
MEMS_AHLD
MEMS_DHLD
MEMS_WRHLD
MEMS_PWRHLD
1.0
1.0
1.0
0.7
—
—
—
—
0.8
0.8
0.8
0.6
—
—
—
—
ns
ns
ns
ns
Table 39.B OR2TxxB Synchronous Memory Write Characteristics (SSPM and SDPM Modes) (continued)
OR2TxxB Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2Txx B Industrial: VDD = 3.0 V to 3.6 V, –40 °C ≤ TA ≤ +8 5 °C.
Parameter Symbol
Speed Unit
-7 -8
Min Max Min Max
CK
F[3:0]
A[3:0], B[3:0]
WD[3:0]
MEMS_ASET
A4 (WREN)
MEMS_AHLD
MEMS_DSET MEMS_DHLD
MEMS_WRSET MEMS_WRHLD
MEMS_PWRSET MEMS_PWRHLD
C0 (WPE) TFSCH/TSCH TFSCL/TSCL
FMEMS_DEL/MEMS_DEL
Timing Characteristics (continued)
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 147
Timing Characteristics (continued)
Note: Speed grades of -5, -6, and -7 are for OR2TxxA de vi ces only.
5-4622(F).r2.a
Figure 61. Synchronous Memory Read Cycle
Table 40A. OR2CxxA and OR2TxxA Synchronous Memory Read Characteristics (SSPM and SDPM Modes)
OR2CxxA Commercial: VDD = 5.0 V ± 5%, 0 °C ≤ TA ≤ 70 °C; OR2CxxA Industrial: VDD = 5. 0 V ± 10%, –40 ° C ≤ TA ≤ +85 °C.
OR2TxxA Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2TxxA Industrial: VDD = 3.0 V to 3.6 V, –40 °C ≤ TA ≤
+85 °C.
Parameter Symbol
Speed Unit
-2 -3 -4 -5 -6 -7
Min Max Min Max Min Max Min Max Min Max Min Max
Read Operation (TJ = 85 °C, VDD = min):
Read Cycle Time
Data Valid After Address
(A[3:0], B[3:0] to F[3:0])
TRC
MEMS*_ADEL 5.1
——
4.0 3.6
——
2.8 2.7
——
2.1 2.4
——
1.7 2.3
——
1.4 2.0
——
1.1 ns
ns
Read Operation, Clocking Data Into
Latch/FF (TJ = 85 °C, VDD = m in):
Address to Clock Setup Time
(A[3:0], B[3:0] to CK)
Clock to PFU Output—Regis ter
(CK to Q[3: 0])
MEMS*_ASET
REG_DEL
2.4
—
—
2.4
1.8
—
—
2.0
1.2
—
—
1.9
1.1
—
—
1.5
1.0
—
—
1.3
0.9
—
—
1.0
ns
ns
Table 40B. OR2TxxB Synchronous Memory Read Characteristics (SSPM and SDPM Modes)
OR2TxxB Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2TxxB I ndustrial: VDD = 3.0 V to 3. 6 V, –40 °C ≤ TA ≤
+85 °C.
Parameter Symbol
Speed Unit
-7 -8
Min Max Min Max
Read Operation (TJ = 85 °C, VDD = min):
Read Cycle Time
Data Valid After Address
(A[3:0], B[3:0] to F[3:0])
TRC
MEMS*_ADEL 1.9
——
1.8 1.8
——
1.4 ns
ns
Read Operation, Clocking Data into
Latch/FF (TJ = 85 °C, VDD = M in):
Address to Clock Setup Time
(A[3:0], B[3:0] to CK)
Clock to PFU Output—Regis ter
(CK to Q[3: 0])
MEMS*_ASET
REG_DEL
0.9
—
—
1.0
0.8
—
—
1.0
ns
ns
A[3:0], B[3:0]
F[3:0]
CK
Q[3:0]
MEM*_ADEL
REG_DEL
MEM*_ASET
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
148 Lucent Technologies Inc.
Timing Characteristics (continued)
Note: Speed grades of -5, -6, and -7 are for OR2TxxA de vi ces only.
Table 41A. OR2CxxA and OR2TxxA PFU Output MUX, PLC BIDI, and Direct Routing Timing Characteristics
OR2CxxA Commercial: VDD = 5.0 V ± 5%, 0 °C ≤ TA ≤ 70 °C; OR2CxxA Industrial: VDD = 5. 0 V ± 10%, –40 ° C ≤ TA ≤ +85 °C.
OR2TxxA Commercial: VDD = 3.0 V to 3. 6 V, 0 °C ≤ TA ≤ 70 °C; OR 2TxxA Indu strial: VDD = 3.0 V to 3.6 V, –40 °C ≤ TA ≤ +85 °C.
Parameter Symbol
Speed Unit
-2 -3 -4 -5 -6 -7
Min Max Min Max Min Max Min Max Min Max Min Max
PFU Output MUX (TJ = 85 °C, VDD = min)
Output MUX Delay (F[3:0]/ Q[3:0] to O[4:0]) OMUX_DEL — 1.1 — 0.8 — 0.6 — 0.5 — 0.4 — 0.4 ns
PLC 3-Statable BIDIs (TJ = 85 °C, VDD = min)
BIDI Propagation Delay
BIDI 3-state Enable/Disable D elay TRI_DEL
TRIEN_DEL —
—1.2
1.7 —
—1.0
1.3 —
—0.8
1.0 —
—0.7
0.8 —
—0.6
0.8 —
—0.5
0.7 ns
ns
Direct Routing (TJ = 85 °C, VDD = min)
PFU to PFU Delay (xSW)
PFU Feedback (xSW) DIR_DEL
FDBK_DEL —
—1.4
1.0 —
—1.1
0.8 —
—0.9
0.7 —
—0.7
0.6 —
—0.6
0.5 —
—0.6
0.5 ns
ns
Table 41B. OR2TxxB PFU Output MUX, PLC BIDI, and Direct Routing Timing Characteristics
OR2TxxB Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2TxxA Industrial: VDD = 3.0 V to 3.6 V, –40 °C ≤ TA ≤
+85 °C.
Parameter Symbol
Speed Unit
-7 -8
Min Max Min Max
PFU Output MUX (TJ = 85 °C, VDD = min)
Output MUX Delay (F[3:0]/Q[3:0] to O[4:0]) OMUX_DEL — 0.4 — 0.4 ns
PLC 3-Statable BIDIs (TJ = 85 °C, VDD = min)
BIDI Propagation Delay
BIDI 3-state Enable/Disable D elay TRI_DEL
TRIEN_DEL —
—0.7
1.1 —
—0.6
0.9 ns
ns
Direct Routing (TJ = 85 °C, VDD = min)
PFU to PFU Delay (xSW)
PFU Feedback (xSW) DIR_DEL
FDBK_DEL —
—0.6
0.4 —
—0.5
0.4 ns
ns
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 149
Timing Characteristics (continued)
Notes:
This clock delay is for a fully routed clock tree that uses the primar y clock network. It includes both the input buffer delay and the clock routing
to the PFU CLK input. The delay will be reduced if any of the clock branches are not used.
Speed grades of -5, -6, and -7 are for OR2TxxA devices only.
Note: This clock delay is for a fully routed clock tree that uses the prim ary clock network. It includes both the input buffer delay and the clock
routing to the PFU CLK input. The delay will be reduced if any of the clock branches are not used.
Table 42A. OR2CxxA and OR2TxxA Internal Clock Delay
OR2CxxA Commer ci al : VDD = 5.0 V ± 5%, 0 °C ≤ TA ≤ 70 °C; OR2CxxA Industrial: VDD = 5.0 V ± 10%, –40 °C ≤ TA ≤ +85 °C.
OR2TxxA Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2TxxA I ndustrial: VDD = 3.0 V to 3. 6 V, –40 °C ≤ TA ≤
+85 °C.
Device
(TJ = 85 °C, VDD = min) Symbol Speed Unit-2 -3 -4 -5 -6 -7
MinMaxMinMaxMinMaxMinMaxMinMaxMinMax
OR2C04A/OR2T04A CLK_DEL — 4.6 — 4.4 — 4.3 — 3.6 — — — — ns
OR2C06A/OR2T06A CLK_DEL — 4.7 — 4.5 — 4.4 — 3.7 — — — — ns
OR2C08A/OR2T08A CLK_DEL — 4.8 — 4.6 — 4.5 — 3.8 — — — — ns
OR2C10A/OR2T10A CLK_DEL — 4.9 — 4.7 — 4.6 — 3.9 — — — — ns
OR2C12A/OR2T12A CLK_DEL — 5.0 — 4.8 — 4.7 — 4.0 — — — — ns
OR2C15A/OR2T15A CLK_DEL — 5.1 — 4.9 — 4.8 — 4.1 — 3.9 — 3.3 ns
OR2C26A/OR2T26A CLK_DEL — 5.2 — 5.1 — 5.0 — 4.2 — 4.0 — 3.4 ns
OR2C40A/OR2T40A CLK_DEL — 5.6 — 5.4 — 5.3 — 4.5 — 4.2 — 3.6 ns
Table 42B. OR2TxxB Internal Clock Delay
OR2TxxB Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2TxxB I ndustrial: VDD = 3.0 V to 3. 6 V, –40 °C ≤ TA ≤
+85 °C.
Device
(TJ = 85 °C, VDD = min) Symbol Speed Unit-7 -8
Min Max Min Max
OR2T15B CLK_DEL — 3.6 — 3.1 ns
OR2T40B CLK_DEL — 3.8 — 3.3 ns
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
150 Lucent Technologies Inc.
Timing Characteristics (continued)
Notes:
The pin-to-pin timing information from
ORCA
Foundry version 9.2 and later is more accurate than this table. For ear lier versions of
ORCA
Foundry, the pin-to-pin timing parameters in this table should be used instead of results reported by
ORCA
Foundry.
This clock delay is for a fully routed clock tree that uses the pr imary clock networ k . It includes both the input buffer delay, the clock routing to
the PFU CLK input, the clock→Q of the FF, and the delay through the output buffer. The delay will be reduced if any of the clock branches are
not used. The given timing requires that the input clock pin be located at one of the four center PICs on any side of the device and that the
direct FF→I/O routing be used.
If the clock pin is not located at one of the four center PICs, this delay mus t be increased by up to the following amounts:
OR2C/2T04A = 1.5%, OR2C/2T06A = 2.0%, OR2C/2T08A = 3.1%, OR2C/2T10A = 3.9%, OR2C/2T12A = 4.9%, OR2C/2T15A = 5.7%,
OR2C/2T26A = 8.1%, OR2C/2T40A = 12.5%.
Speed grades of -5, -6, and -7 are for OR2TxxA devices only.
Table 43A. OR2CxxA and OR2TxxA OR2CxxA/OR2TxxA Global Cloc k to Output Delay (Pin-to-Pin)—Output
on Same Side of the Device as the Clock Pin
OR2CxxA Commer ci al : VDD = 5.0 V ± 5%, 0 °C ≤ TA ≤ 7 0 °C; In dustrial: VDD = 5.0 V ± 10%, –40 °C ≤ TA ≤ +85 °C; CL = 50 pF.
OR2TxxA Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C ≤ TA ≤ +85 °C; CL =
50 pF.
Description
(TJ = 85 °C, VDD = min) Device Speed Unit-2 -3 -4 -5 -6 -7
Min Max Min Max Min Max Min Max Min Max Min Max
CLK Input Pin → OUTPUT Pin
(Fast) OR2C/2T04A
OR2C/2T06A
OR2C/2T08A
OR2C/2T10A
OR2C/2T12A
OR2C/2T15A
OR2C/2T26A
OR2C/2T40A
—
—
—
—
—
—
—
—
11.7
11.8
11.9
12.0
12.1
12.2
12.3
12.7
—
—
—
—
—
—
—
—
10.3
10.4
10.5
10.6
10.7
10.8
11.0
11.4
—
—
—
—
—
—
—
—
9.8
9.9
10.0
10.1
10.2
10.3
10.5
10.8
—
—
—
—
—
—
—
—
8.6
8.7
8.8
8.9
9.0
9.1
9.2
9.5
—
—
—
—
—
—
—
—
—
—
—
—
—
8.3
8.4
8.6
—
—
—
—
—
—
—
—
—
—
—
—
—
6.7
6.9
7.0
ns
ns
ns
ns
ns
ns
ns
ns
CLK Input Pin → OUTPUT Pin
(Slewlim) OR2C/2T04A
OR2C/2T06A
OR2C/2T08A
OR2C/2T10A
OR2C/2T12A
OR2C/2T15A
OR2C/2T26A
OR2C/2T40A
—
—
—
—
—
—
—
—
13.9
14.0
14.1
14.2
14.3
14.4
14.5
14.9
—
—
—
—
—
—
—
—
12.5
12.6
12.7
12.8
12.9
13.0
13.2
13.6
—
—
—
—
—
—
—
—
11.7
11.8
11.9
12.0
12.1
12.2
12.3
12.6
—
—
—
—
—
—
—
—
10.0
10.1
10.2
10.3
10.4
10.5
10.6
10.9
—
—
—
—
—
—
—
—
—
—
—
—
—
9.5
9.6
9.8
—
—
—
—
—
—
—
—
—
—
—
—
—
7.4
7.5
7.7
ns
ns
ns
ns
ns
ns
ns
ns
CLK Input Pin → OUTPUT Pin
(Sinklim) OR2C/2T04A
OR2C/2T06A
OR2C/2T08A
OR2C/2T10A
OR2C/2T12A
OR2C/2T15A
OR2C/2T26A
OR2C/2T40A
—
—
—
—
—
—
—
—
15.7
15.8
15.9
16.0
16.1
16.2
16.3
16.7
—
—
—
—
—
—
—
—
14.7
14.8
14.9
15.0
15.1
15.2
15.3
15.7
—
—
—
—
—
—
—
—
13.7
13.8
13.9
14.0
14.1
14.2
14.3
14.6
—
—
—
—
—
—
—
—
13.1
13.2
13.3
13.4
13.5
13.6
13.7
14.0
—
—
—
—
—
—
—
—
—
—
—
—
—
12.1
12.2
12.4
—
—
—
—
—
—
—
—
—
—
—
—
—
10.0
10.7
10.9
ns
ns
ns
ns
ns
ns
ns
ns
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 151
Timing Characteristics (continued)
Notes:
The pin-to-pin timing inf ormation from
ORCA
Foundry version 9.2 and later is more accurate than this table . F or earlier v ersions of
ORCA
Foundry,
the pin-to-pin tim ing parameters in this table should be used instead of results reported by
ORCA
Foundry.
This clock delay is for a fully routed clock tree that uses the primar y clock network. It includes both the input buffer delay, the clock routing to the
PFU CLK input, the c lock→Q of the FF, and the delay through the output buffer. The delay will be reduced if any of the clock branches are not
used. The given timing requires that the input clock pin be located at one of the four center PICs on any side of the device and that the direct
FF→I/O routing be used.
If the clock pin is not located at one of the four center PICs, this delay mus t be increased by up to the following amounts:
OR2T15B = 5.7%, OR2T40B = 12.5%.
Figure 62. Global Clock to Output Delay
Table 43B. OR2TxxB Global Clock to Output Delay (Pin-to-Pin)—Output on Same Side of the Device as the
Cloc k Pin
OR2TxxB Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C;
Industrial: VDD = 3.0 V to 3.6 V, –40 °C ≤ TA ≤ +85 °C; CL=50 pF.
Description
(TJ = 85 °C, VDD = min) Device Speed Unit-7 -8
Min Max Min Max
CLK Input Pin → OUTPUT Pin
(Fast) OR2T15B
OR2T40B —
—7.3
7.5 —
—6.6
6.6 ns
ns
CLK Input Pin → OUTPUT Pin
(Slewlim) OR2T15B
OR2T40B —
—8.2
8.4 —
—7.4
7.6 ns
ns
CLK Input Pin → OUTPUT Pin
(Sinklim) OR2T15B
OR2T40B —
—12.9
13.1 —
—12.1
12.3 ns
ns
5-4846(F)
OUTPUT (50 pF LOA D)QD
CLK
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
152 Lucent Technologies Inc.
Timing Characteristics (continued)
Notes:
The pin-to-pin timing information from
ORCA
Foundry version 9.2 and later is more accurate than this table. For ear lier versions of
ORCA
Foundry, the pin-to-pin timing parameters in this table should be used instead of results reported by
ORCA
Foundry.
This clock delay is for a fully routed cloc k tree that uses the primary clock network. It includes both the input b uffer delay, the clock routing to the
PFU CLK input, the c lock→Q of the FF, and the delay through the output buffer. The delay will be reduced if any of the clock branches are not
used. The given timing requires that the input clock pin be located at one of the four center PICs on any side of the device and that the direct
FF→I/O routing be used.
If the clock pin is not located at one of the four center PICs, this delay mus t be increased by up to the following amounts:
OR2C/2T04A = 1.5%, OR2C/2T06A = 2.0%, OR2C/2T08A = 3.1%, OR2C/2T10A = 3.9%, OR2C/2T12A = 4.9%, OR2C/2T15A = 5.7%,
OR2C/2T26A = 8.1%, OR2C/2T40A = 12.5%.
Speed grades of -5, -6, and -7 are for OR2TxxA devices only
Table 44A. OR2CxxA/OR2TxxA Global Clock to Output Delay (Pin-to-Pin)—Output Not on Same
Side of the Device as the Clock Pin
OR2CxxA Commercial : VDD = 5.0 V ± 5%, 0 °C ≤ TA ≤ 70 °C; I ndu strial: V DD = 5.0 V ± 10%, –40 °C ≤ TA ≤ +85 °C; CL = 50 pF.
OR2TxxA Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C;
Industrial: VDD = 3.0 V to 3.6 V, –40 °C ≤ TA ≤ +85 °C; CL = 50 pF.
Description
(TJ = 85 °C, VDD = min) Device Speed Unit-2 -3 -4 -5 -6 -7
Min Max Min Max Min Max Min Max Min Max Min Max
CLK Input Pin → OUTPUT Pin
(Fast) OR2C/2T04A
OR2C/2T06A
OR2C/2T08A
OR2C/2T10A
OR2C/2T12A
OR2C/2T15A
OR2C/2T26A
OR2C/2T40A
—
—
—
—
—
—
—
—
11.8
12.0
12.2
12.4
12.6
12.8
13.1
14.4
—
—
—
—
—
—
—
—
10.5
10.6
10.8
11.0
11.2
11.5
11.9
13.3
—
—
—
—
—
—
—
—
9.9
10.0
10.1
10.3
10.5
10.7
11.1
12.4
—
—
—
—
—
—
—
—
8.8
8.9
9.0
9.2
9.4
9.6
10.0
11.1
—
—
—
—
—
—
—
—
—
—
—
—
—
8.9
9.3
10.5
—
—
—
—
—
—
—
—
—
—
—
—
—
7.3
7.7
8.3
ns
ns
ns
ns
ns
ns
ns
ns
CLK Input Pin → OUTPUT Pin
(Slewlim) OR2C/2T04A
OR2C/2T06A
OR2C/2T08A
OR2C/2T10A
OR2C/2T12A
OR2C/2T15A
OR2C/2T26A
OR2C/2T40A
—
—
—
—
—
—
—
—
14.1
14.3
14.4
14.6
14.8
15.0
15.3
16.7
—
—
—
—
—
—
—
—
12.7
12.9
13.1
13.3
13.5
13.6
14.1
15.5
—
—
—
—
—
—
—
—
11.8
11.9
12.0
12.2
12.4
12.6
12.9
14.2
—
—
—
—
—
—
—
—
10.3
10.4
10.5
10.6
10.8
11.0
11.4
12.5
—
—
—
—
—
—
—
—
—
—
—
—
—
10.1
10.5
11.7
—
—
—
—
—
—
—
—
—
—
—
—
—
8.0
8.4
9.1
ns
ns
ns
ns
ns
ns
ns
ns
CLK Input Pin → OUTPUT Pin
(Sinklim) OR2C/2T04A
OR2C/2T06A
OR2C/2T08A
OR2C/2T10A
OR2C/2T12A
OR2C/2T15A
OR2C/2T26A
OR2C/2T40A
—
—
—
—
—
—
—
—
15.9
16.0
16.2
16.4
16.6
16.8
17.1
18.5
—
—
—
—
—
—
—
—
14.8
15.0
15.2
15.4
15.6
15.8
16.2
17.6
—
—
—
—
—
—
—
—
13.8
13.9
14.1
14.2
14.4
14.6
14.9
16.3
—
—
—
—
—
—
—
—
13.4
13.5
13.6
13.7
13.9
14.1
14.4
15.6
—
—
—
—
—
—
—
—
—
—
—
—
—
12.7
13.1
14.3
—
—
—
—
—
—
—
—
—
—
—
—
—
11.2
11.6
12.2
ns
ns
ns
ns
ns
ns
ns
ns
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 153
.Timing Characteristics (continued)
Notes:
The pin-to-pin timing inf ormation from
ORCA
Foundry version 9.2 and later is more accurate than this table . F or earlier v ersions of
ORCA
Foundry,
the pin-to-pin tim ing parameters in this table should be used instead of results reported by
ORCA
Foundry.
This clock delay is for a fully routed clock tree that uses the primar y clock network. It includes both the input buffer delay, the clock routing to the
PFU CLK input, the c lock→Q of the FF, and the delay through the output buffer. The delay will be reduced if any of the clock branches are not
used. The given timing requires that the input clock pin be located at one of the four center PICs on any side of the device and that the direct
FF→I/O routing be used.
If the clock pin is not located at one of the four center PICs, this delay mus t be increased by up to the following amounts:
OR2T15B = 5.7%, OR2T40B = 12.5%.
Figure 63. Global Clock to Output Delay
Table 44B. OR2TxxB Global Clock to Output Delay (Pin-to-Pin)—Output Not on Same Side of the Device as
the Clock Pin
OR2TxxB Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C;
Industrial: VDD = 3.0 V to 3.6 V, –40 °C ≤ TA ≤ +85 °C; CL = 50 pF.
Description
(TJ = 85 °C, VDD = min) Device Speed Unit-7 -8
MinMaxMinMax
CLK Input Pin → OUTPUT Pin
(Fast) OR2T15B
OR2T40B —
—7.6
8.1 —
—6.9
7.4 ns
ns
CLK Input Pin → OUTPUT Pin
(Slewlim) OR2T15B
OR2T40B —
—8.4
9.0 —
—7.7
8.2 ns
ns
CLK Input Pin → OUTPUT Pin
(Sinklim) OR2T15B
OR2T40B —
—13.2
13.7 —
—12.4
12.8 ns
ns
OUTPUT (50 pF LOAD)QD
CLK
5-4846(F)
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
154 Lucent Technologies Inc.
Timing Characteristics (continued)
Notes:
The pin-to-pin timing parameters in this table should be used instead of results reported by
ORCA
Foundry.
This clock dela y is for a fully routed clock tree that uses the primary clock network. It includes both the input buf fer delay and the cloc k routing to
the PFU CLK input. The delay will be reduced if any of the clock branches are not us ed. The given Setup (Delayed and No delay) and Hold
(Delayed) timing allows the input cloc k pin to be located in an y PIC on any side of the de vice , but direct I/O→FF routing must be used. The Hold
(No delay) timing assumes the clock pin is located at one of the four center PICs and direct I/O→FF routing is used. If it is not located at one of
the four center PICs, this delay must be increased by up to the following amounts: OR2C/2T04A = 5.3%, OR2C/2T06A = 6.4%, OR2C/2T08A =
7.3%, OR2C/2T10A = 9.1%, OR2C/2T12A = 10.8%, OR2C/2T15A = 12.2%, OR2C/2T26A = 16.1%, OR2C/2T40A = 21.2%.
Speed grades of -5, -6, and -7 are for OR2TxxA devices only.
Table 45A. OR2CxxA/OR2TxxA Global Input to Clock Setup/Hold Time (Pin-to-Pin)
OR2CxxA Commercial: VDD = 5.0 V ± 5%, 0 °C ≤ TA ≤ 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C ≤ TA ≤ +85 °C.
OR2TxxA Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; Industr ial: VDD = 3.0 V to 3.6 V, –40 °C ≤ TA ≤ +85 °C.
Description
(TJ = all, VDD = all) Device Speed Unit-2 -3 -4 -5 -6 -7
Min Max Min Max Min Max Min Max Min Max Min Max
Input to CLK (TTL/CMOS)
Setup Time (no delay) OR2C/2T04A
OR2C/2T06A
OR2C/2T08A
OR2C/2T10A
OR2C/2T12A
OR2C/2T15A
OR2C/2T26A
OR2C/2T40A
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
—
—
—
—
—
—
—
—
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
—
—
—
—
—
—
—
—
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
—
—
—
—
—
—
—
—
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
—
—
—
—
—
—
—
—
—
—
—
—
—
0.0
0.0
0.0
—
—
—
—
—
—
—
—
—
—
—
—
—
0.0
0.0
0.0
—
—
—
—
—
—
—
—
ns
ns
ns
ns
ns
ns
ns
ns
Input to CLK (TTL/CMOS)
Setup Time (delay ed) OR2C/2T04A
OR2C/2T06A
OR2C/2T08A
OR2C/2T10A
OR2C/2T12A
OR2C/2T15A
OR2C/2T26A
OR2C/2T40A
5.8
5.7
5.6
5.3
5.2
4.9
7.3
6.8
—
—
—
—
—
—
—
—
5.5
5.4
5.3
5.0
4.9
4.7
6.9
6.4
—
—
—
—
—
—
—
—
4.2
4.1
4.0
3.9
3.8
3.6
6.0
5.5
—
—
—
—
—
—
—
—
4.0
3.9
3.8
3.7
3.6
3.4
5.7
5.2
—
—
—
—
—
—
—
—
—
—
—
—
—
4.1
6.7
6.5
—
—
—
—
—
—
—
—
—
—
—
—
—
4.1
6.0
5.8
—
—
—
—
—
—
—
—
ns
ns
ns
ns
ns
ns
ns
ns
Input to CLK (TTL/CMOS)
Hold Time (no delay) OR2C/2T04A
OR2C/2T06A
OR2C/2T08A
OR2C/2T10A
OR2C/2T12A
OR2C/2T15A
OR2C/2T26A
OR2C/2T40A
4.2
4.3
4.5
4.8
5.0
5.4
6.2
7.9
—
—
—
—
—
—
—
—
4.0
4.1
4.3
4.6
4.8
5.1
5.8
6.8
—
—
—
—
—
—
—
—
3.8
3.9
4.1
4.4
4.6
4.9
5.6
6.6
—
—
—
—
—
—
—
—
3.6
3.7
3.9
4.2
4.4
4.7
5.3
6.3
—
—
—
—
—
—
—
—
—
—
—
—
—
4.2
4.6
5.8
—
—
—
—
—
—
—
—
—
—
—
—
—
3.7
4.1
4.9
—
—
—
—
—
—
—
—
ns
ns
ns
ns
ns
ns
ns
ns
Input to CLK (TTL/CMOS)
Hold Time (delay ed) OR2C/2T04A
OR2C/2T06A
OR2C/2T08A
OR2C/2T10A
OR2C/2T12A
OR2C/2T15A
OR2C/2T26A
OR2C/2T40A
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
—
—
—
—
—
—
—
—
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
—
—
—
—
—
—
—
—
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
—
—
—
—
—
—
—
—
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
—
—
—
—
—
—
—
—
—
—
—
—
—
0.0
0.0
0.0
—
—
—
—
—
—
—
—
—
—
—
—
—
0.0
0.0
0.0
—
—
—
—
—
—
—
—
ns
ns
ns
ns
ns
ns
ns
ns
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 155
Timing Characteristics (continued)
Notes:
The pin-to-pin timing parameters in this table should be used instead of results reported by
ORCA
Foundry.
This cloc k dela y is for a fully routed clock t ree that uses the primary clock netw ork. It includes both the input b uffer delay and the cloc k routi ng to
the PFU CLK input. The delay will be reduced if any of the clock branches are not us ed. The given Setup (delayed and no delay) and Hold
(delayed) timing allows the input clock pin to be located in any PIC on any side of the device, b ut direct I/O→FF routing must be used. The Hold
(no delay) timing assumes the clock pin is located at one of the f our center PICs and direct I/O→FF routing is used. If it is not located at one of
the four center PICs, this delay must be increased by up to the following amounts: OR2T15B = 5.7%, OR2T40B = 12.5%.
Figure 64. Global Input to Clock Setup/Hold Time
Table 45B. OR2TxxB Global Input to Clock Setup/Hold Time (Pin-to-Pin)
OR2TxxB Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; Industr ial: VDD = 3.0 V to 3.6 V, –40 °C ≤ TA ≤ +85 °C.
Description
(TJ = all, VDD = all) Device Speed Unit-7 -8
Min Max Min Max
Input to CLK (TTL/CMOS)
Setup Time (no delay) OR2T15B
OR2T40B 0.0
0.0 —
—0.0
0.0 —
—ns
ns
Input to CLK (TTL/CMOS)
Setup Time (delay ed) OR2T15B
OR2T40B 4.7
7.7 —
—4.0
5.5 —
—ns
ns
Input to CLK (TTL/CMOS)
Hold Time (no delay) OR2T15B
OR2T40B 1.6
1.4 —
—1.4
1.3 —
—
ns
ns
Input to CLK (TTL/CMOS)
Hold Time (delay ed) OR2T15B
OR2T40B 0.0
0.0 —
—0.0
0.0 —
—ns
ns
QD
CLK
INPUT
5-4847(F)
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
156 Lucent Technologies Inc.
Timing Characteristics (continued)
Notes:
If the input buffer is placed in delay mode, the chip hold time to the nearest PFU latch is guaranteed to be 0 if the clock is r outed using the
primary clock network; (TJ = all, VDD = all). It should also be noted that any signals routed on the clock lines or using the TRIDI buffers dir ectly
from the input buffer do not get delayed at any time.
The delays for all input buffers assume an input rise/fall time of ≤1 V/ns.
Speed grades of -5, -6, and -7 are for OR2TxxA devices only
Table 46A. OR2CxxA/OR2TxxA Programmable I/O Cell Timing Characteristics
OR2CxxA Commer ci al : VDD = 5.0 V ± 5%, 0 °C ≤ TA ≤ 70 °C; OR2CxxA Industr ial: VDD = 5.0 V ± 10%, –40 °C ≤ TA ≤ +85 °C.
OR2TxxA Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2Txx A Industrial: VDD = 3.0 V to 3.6 V, –40 °C ≤ TA ≤ +85 °C.
Parameter Symbol Speed Unit-2 -3 -4 -5 -6 -7
Min Max Min Max Min Max Min Max Min Max Min Max
Inputs (TJ = 85 °C, VDD = min)
Input Rise Time TR— 500 — 500 — 500 — 500 — 500 — 500 ns
Input Fall Time TF— 500 — 500 — 500 — 500 — 500 — 500 ns
Pad to In Delay PAD_IN_DEL — 1.7 — 1.5 — 1.3 — 1.2 — 1.2 — 1.1 ns
Pad to Nearest PFU Latch Output CHIP_LATCH — 6.2 — 4.7 — 4.1 — 3.5 — 3.1 — 2.9 ns
Delay Added to General Routing
(input buffer in delay mode f or
OR2C/2T15A and smaller
devices)
— — 8.1 — 7.0 — 6.0 — 5.9 — 6.2 — 5.8 ns
Delay Added to General Routing
(input buffer in delay mode f or
OR2C/2T26A and OR2C/2T40A)
— — 11.0 — 9.7 — 8.6 — 8.6 — 9.0 — 8.6 ns
Delay Added to Direct-FF Routing
(input buffer in delay mode f or
OR2C/2T15A and smaller
devices)
— — 8.0 — 6.8 — 5.9 — 6.0 — 6.4 — 6.0 ns
Delay Added to Direct-FF Routing
(input buffer in delay mode f or
OR2C/2T26A and OR2C/2T40A)
— — 10.9 — 10.2 — 8.5 — 8.6 — 9.1 — 7.9 ns
Outputs (TJ = 85 °C, VDD = min, CL = 50 pF)
PFU CK to P ad Dela y (DOUT[3:0] t o
PAD):
Fast
Slewlim
Sinklim
DOUT_DEL(F)
DOUT_DEL(SL)
DOUT_DEL(SI)
—
—
—
7.1
9.4
11.2
—
—
—
6.2
8.4
10.5
—
—
—
5.5
7.4
9.4
—
—
—
5.0
6.4
9.5
—
—
—
4.4
5.6
8.3
—
—
—
3.3
4.1
7.2
ns
ns
ns
Output to Pad Delay (OUT[3:0] to
PAD):
Fast
Slewlim
Sinklim
OUT_DEL(F)
OUT_DEL(SL)
OUT_DEL(SI)
—
—
—
5.0
6.7
9.8
—
—
—
4.0
6.3
7.2
—
—
—
3.6
5.5
7.5
—
—
—
3.1
4.5
7.6
—
—
—
2.7
3.9
6.5
—
—
—
2.3
3.1
6.2
ns
ns
ns
3-state Enable Delay (TS[3:0] to
PAD):
Fast
Slewlim
Sinklim
TS_DEL(F)
TS_DEL(SL)
TS_DEL(SI)
—
—
—
5.8
7.5
10.6
—
—
—
4.7
7.0
7.9
—
—
—
4.0
6.3
8.4
—
—
—
3.5
5.2
9.3
—
—
—
3.1
4.7
8.0
—
—
—
2.5
3.7
7.6
ns
ns
ns
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 157
.Timing Characteristics (continued)
Notes:
If the input buffer is placed in delay mode, the chip hold time to the nearest PFU latch is guaranteed to be 0 if the clock is r outed using the
primary clock network; (TJ = all, VDD = all). It should also be noted that any signals routed on the clock lines or using the TRIDI buffers dir ectly
from the input buffer do not get delayed at any time.
The delays for all input buffers assume an input rise/fall time of ≤1 V/ns.
Table 46B. OR2TxxB Programmable I/O Cell Timing Characteristics
OR2TxxA Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2TxxA Industrial: VDD = 3.0 V to 3.6 V, –40 °C ≤ TA ≤
+85 °C.
Parameter Symbol Speed Unit-7 -8
Min Max Min Max
Inputs (TJ = 85 °C, VDD = min)
Input Rise Time TR— 500 — 500 ns
Input Fall Time TF— 500 — 500 ns
Pad to In Delay PAD_IN_DEL — 1.1 — 1.0 ns
Pad to Nearest PFU Latch Output CHIP_LATCH — 3.3 — 2.4 ns
Delay Added to General Routing
(input buffer in delay mode f or
OR2T15B and smaller devices)
— — 6.6 — 6.1 ns
Delay Added to General Routing
(input buffer in delay mode f or
OR2T40B)
— — 8.9 — 8.2 ns
Delay Added to Direct-FF Routing
(input buffer in delay mode f or
OR2T15B and smaller devices)
— — 6.4 — 6.0 ns
Delay Added to Direct-FF Routing
(input buffer in delay mode f or
OR2T40B)
— — 8.7 — 8.0 ns
Outputs (TJ = 85 °C, VDD = min, CL = 50 pF)
PFU CK to P ad Dela y (DOUT[3:0] t o
PAD):
Fast
Slewlim
Sinklim
DOUT_DEL(F)
DOUT_DEL(SL)
DOUT_DEL(SI)
—
—
—
2.8
3.6
8.3
—
—
—
2.5
3.3
8.0
ns
ns
ns
Output to Pad Delay (OUT[3:0] to
PAD):
Fast
Slewlim
Sinklim
OUT_DEL(F)
OUT_DEL(SL)
OUT_DEL(SI)
—
—
—
2.8
3.6
8.3
—
—
—
2.5
3.3
8.0
ns
ns
ns
3-state Enable Delay (TS[3:0] to
PAD):
Fast
Slewlim
Sinklim
TS_DEL(F)
TS_DEL(SL)
TS_DEL(SI)
—
—
—
3.0
3.8
9.1
—
—
—
2.7
3.4
8.7
ns
ns
ns
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
158 Lucent Technologies Inc.
Timing Characteristics (con tinued)
Table 47. Series 2 General Configuration Mode Timing Characteristics
OR2CxxA Commer ci al : VDD = 5.0 V ± 5%, 0 °C ≤ TA ≤ 70 °C; OR2CxxA Industr ial: VDD = 5.0 V ± 10%, –40 °C ≤ TA ≤ +85 °C.
OR2TxxA/B Commercia l: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2TxxA/B Indu st rial: VDD = 3.0 V to 3.6 V,
–40 °C ≤ TA ≤ +85 °C.
Parameter Symbol Min Max Unit
All Configuration Modes
M[3:0] Setup Time to INIT High TSMODE 50.0 — ns
M[3:0] Hold Time from INIT High THMODE 600.0 — ns
RESET Pulse Width Low to Start Reconfiguration TRW 50.0 — ns
PRGM Pulse Width Low to Start Reconfiguration TPGW 50.0 — ns
Master and Asynchronous Peripheral Modes
Power-on Reset Dela y
CCLK Period (M3 = 0)
(M3 = 1)
Configuration Latency (noncompressed):
OR2C/2T04A (M3 = 0)
(M3 = 1)
OR2C/2T06A (M3 = 0)
(M3 = 1)
OR2C/2T08A (M3 = 0)
(M3 = 1)
OR2C/2T10A (M3 = 0)
(M3 = 1)
OR2C/2T12A (M3 = 0)
(M3 = 1)
OR2C/2T15A/2T15B (M3 = 0)
(M3 = 1)
OR2C/2T26A (M3 = 0)
(M3 = 1)
OR2C/2T40A/2T40B (M3 = 0)
(M3 = 1)
TPO
TCCLK
TCL
17.30
66.0
528.00
4.31
34.48
6.00
48.00
7.62
60.96
9.82
78.56
11.86
94.88
14.57
116.56
20.25
162.00
31.29
250.32
69.47
265.00
2120.00
17.30*
138.40*
24.08*
192.64*
30.60*
244.80*
39.43*
315.44*
47.62*
380.96*
58.51*
468.08*
81.32*
650.56*
125.62*
1004.96*
ms
ns
ns
ms
ms
ms
ms
ms
ms
ms
ms
ms
ms
ms
ms
ms
ms
ms
ms
Slave Serial and Synchronous Peripheral Modes
Power-on Reset Dela y
CCLK Period (OR2CxxA/OR2TxxA)
CCLK Period (OR2TxxB)
Configuration Latency (noncompressed):
OR2C/2T04A
OR2C/2T06A
OR2C/2T08A
OR2C/2T10A
OR2C/2T12A
OR2C/2T15A
OR2T15B
OR2C/2T26A
OR2C/2T40A
OR2T40B
TPO
TCCLK
TCCLK
TCL
4.33
100.00
25.00
6.53
9.09
11.55
14.88
17.97
22.08
5.52
30.69
47.40
11.85
17.37
—
—
—
—
—
—
—
—
—
—
—
—
ms
ns
ns
ms
ms
ms
ms
ms
ms
ms
ms
ms
ms
* Not applicable to asynchronous peripheral mode.
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 159
Note: TPO is triggered when VDD reaches between 3.0 V to 4.0 V for the OR2CxxA and between 2.7 V and 3.0 V for the OR2TxxA/OR2TxxB.
Slave Parallel Mode
Power-on Reset Delay
CCLK Period (OR2CxxA/OR2TxxA)
CCLK Period (OR2TxxB)
Configuration Latency (noncompressed):
OR2C/2T04A
OR2C/2T06A
OR2C/2T08A
OR2C/2T10A
OR2C/2T12A
OR2C/2T15A
OR2T15B
OR2C/2T26A
OR2C/2T40A
OR2T40B
TPO
TCCLK
TCCLK
TCL
4.33
100.00
25.0
0.82
1.14
1.44
1.86
2.25
2.76
0.69
3.84
5.93
1.48
17.37
—
—
—
—
—
—
—
—
—
—
—
—
ms
ns
ns
ms
ms
ms
ms
ms
ms
ms
ms
ms
ms
Partial Reconfiguration (noncompressed):
OR2C/2T04A
OR2C/2T06A
OR2C/2T08A
OR2C/2T10A
OR2C/2T12A
OR2C/2T15A/2T15B
OR2C/2T26A
OR2C/2T40A/2T40B
TPR 1.70
2.00
2.20
2.50
2.70
3.00
3.50
4.30
—
—
—
—
—
—
—
—
µs/frame
µs/frame
µs/frame
µs/frame
µs/frame
µs/frame
µs/frame
µs/frame
INIT Timing
INIT High to CCLK Delay:
Slave Parall el
Slave Serial
Synchronous Peripheral
Master Serial:
(M3 = 1)
(M3 = 0)
Master Parallel:
(M3 = 1)
(M3 = 0)
TINIT_CLK 1.00
1.00
1.00
1.06
0.59
5.28
1.12
—
—
—
4.51
2.65
21.47
4.77
µs
µs
µs
µs
µs
µs
µs
Initialization Latency (PRGM high to INIT high) :
OR2C/2T04A
OR2C/2T06A
OR2C/2T08A
OR2C/2T10A
OR2C/2T12A
OR2C/2T15A/2T15B
OR2C/2T26A
OR2C/2T40A/2T40B
TIL 63.36
74.98
86.59
98.21
109.82
121.44
144.67
181.90
254.40
301.04
347.68
394.32
440.96
487.60
580.88
730.34
µs
µs
µs
µs
µs
µs
µs
µs
INIT High to WR, Asynchronous Peripheral TINIT_WR 1.50 — µs
Timing Characteristics (continued)
Table 47. Series 2 General Configuration Mode Timing Characteristics (continued)
OR2CxxA Commer ci al : VDD = 5.0 V ± 5%, 0 °C ≤ TA ≤ 70 °C; OR2CxxA Industrial: VDD = 5.0 V ± 10%, –40 °C ≤ TA ≤ +85 °C.
OR2TxxA/B Commercia l: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2T x xA/B Industrial: VDD = 3.0 V to 3.6 V,
–40 °C ≤ TA ≤ +85 °C.
Parameter Symbol Min Max Unit
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
160 Lucent Technologies Inc.
Timing Characteristics (con tinued)
Series 2
Figure 65. General Configuration Mode Timing Diagram
5-4531(F)
VDD
CCLK
M[3:0]
PRGM
INIT
TPO + TIL
TIL
TCCLK
TSMODE THMODE
TINIT_CLK
DONE TCL
TPGW
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 161
Timing Characteristics (continued)
Note: Serial configuration data is transmitted out on DOUT on the falling edge of CCLK after it is input DIN.
Figure 66. Master Serial Configuration Mode Timing Diagram
Table 48. Series 2 Master Serial Configuration Mode Timing Characteristics
OR2CxxA Commer ci al : VDD = 5.0 V ± 5%, 0 °C ≤ TA ≤ 70 °C; OR2CxxA Industrial: VDD = 5.0 V ± 10%, –40 °C ≤ TA ≤ +85 °C.
OR2TxxA/B Commercia l: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2T x xA/B Industrial: VDD = 3.0 V to 3.6 V,
–40 °C ≤ TA ≤ +85 °C.
Parameter Symbol Min Nom Max Unit
DIN Setup Time TS60.0 — — ns
DIN Hold Time TH0——ns
CCLK Frequency (M3 = 0) FC3.8 10.0 15.2 MHz
CCLK Frequency (M3 = 1) FC0.48 1.25 1.9 MHz
CCLK to DOUT Delay TD——30ns
5-4532(F)
DIN
CCLK
DOUT
TSTH
BIT N
TD
BIT N
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
162 Lucent Technologies Inc.
Timing Characteristics (continued)
Notes:
The RCLK period consists of seven CCLKs f or RCLK low and one CCLK for RCLK high.
Serial data is transmitted out on DOUT 1.5 CCLK cycles after the byte is input D[7:0]
f.44(F)
Figure 67. Master Parallel Configuration Mode Timing Diagram
Table 49. Series 2 Master P arallel Configuration Mode Timing Characteristics
OR2CxxA Commer ci al : VDD = 5.0 V ± 5%, 0 °C ≤ TA ≤ 70 °C; OR2CxxA Industr ial: VDD = 5.0 V ± 10%, –40 °C ≤ TA ≤ +85 °C.
OR2TxxA/B Commercia l: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2TxxA/B Indu st rial: VDD = 3.0 V to 3.6 V,
–40 °C ≤ TA ≤ +85 °C.
Parameter Symbol Min Max Unit
RCLK to Address Valid TAV 0 200 ns
D[7:0] Setup Time to RCLK High TS60 — ns
D[7:0] Hold Time to RCLK High TH0—ns
RCLK Low Time (M3 = 0) TCL 462 1855 ns
RCLK High Time (M3 = 0) TCH 66 265 ns
RCLK Low Time (M3 = 1) TCL 3696 14840 ns
RCLK High Time (M3 = 1) TCH 528 2120 ns
CCLK to DOUT TD—30ns
A[17:0]
RCLK
D[7:0]
TCL
TCH
TAV
CCLK
DOUT
TH
TS
BYTE N BYTE N + 1
D0 D1 D2 D3 D4 D5 D6 D7
TD
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 163
Timing Characteristics (continued)
* This parameter is valid whether the end of not RDY is determined from the RDY/RCLK pin or from the D7 pin.
Notes:
Serial data is transmitted out on DOUT on the falling edge of CCLK after the byte is input D[7:0].
D[6:0] timing is the same as the write data port of the D7 waveform because D[6:0] are not enabled.
Figure 68. Asynchronous Peripheral Configuration Mode Timing Diagram
Table 50. Series 2 Asynchronous Peripheral Configuration Mode Timing Characteristics
OR2CxxA Commer ci al : VDD = 5.0 V ± 5%, 0 °C ≤ TA ≤ 70 °C; OR2CxxA Industrial: VDD = 5.0 V ± 10%, –40 °C ≤ TA ≤ +85 °C.
OR2TxxA/B Commercia l: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2T x xA/B Industrial: VDD = 3.0 V to 3.6 V,
–40 °C ≤ TA ≤ +85 °C.
Parameter Symbol Min Max Unit
WR, CS0, and CS1 Pulse Width TWR 100 — ns
D[7:0] Setup Time TS20 — ns
D[7:0] Hold Time TH0—ns
RDY Delay TRDY —60ns
RDY Low TB18CCLK Periods
Earliest WR After RDY Goes High* TWR2 0—ns
RD to D7 Enable/Disable TDEN —60ns
CCLK to DOUT TD—30ns
5-4533.a
CS1
D7
CCLK
DOUT
CS0
RDY
D0 D1 D2
TB
TWR
TSTH
TRDY
WR
D7
TD
PREVIOUS BYTE
TWR2
WRITE DATA
D3
TDEN TDEN
RD
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
164 Lucent Technologies Inc.
Timing Characteristics (con tinued)
Note: Serial data is transmi tted out on DOUT 1.5 clock cycles after the byte is input D[7:0].
Note: Serial data is transmi tted out on DOUT 1.5 clock cycles after the byte is input D[7:0].
Figure 69. Synchronous Peripheral Configuration Mode Timing Diagram
Table 51A. OR2CxxA/OR2TxxA Synchronous Peripheral Configuration Mode Timing Characteristics
OR2CxxA Commer ci al : VDD = 5.0 V ± 5%, 0 °C ≤ TA ≤ 70 °C; OR2CxxA Industr ial: VDD = 5.0 V ± 10%, –40 °C ≤ TA ≤ +85 °C.
OR2TxxA Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2Txx A Industrial: VDD = 3.0 V to 3.6 V, –40 °C ≤ TA ≤ +85 °C.
Parameter Symbol Min Max Unit
D[7:0] Setup Time TS20 — ns
D[7:0] Hold Time TH0—ns
CCLK High Time TCH 50 — ns
CCLK Low Time TCL 50 — ns
CCLK Frequency FC—10MHz
CCLK to DOUT TD—30ns
Table 51B. OR2TxxB Synchronous Peripheral Configuration Mode Timing Characteristics
OR2TxxB Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2Txx B Industrial: VDD = 3.0 V to 3.6 V, –40 °C ≤ TA ≤ +85 °C.
Parameter Symbol Min Max Unit
D[7:0] Setup Time TS15 — ns
D[7:0] Hold Time TH0—ns
CCLK High Time TCH 12.5 — ns
CCLK Low Time TCL 12.5 — ns
CCLK Frequency FC—40MHz
CCLK to DOUT TD—10ns
5-4534(F)
CCLK
INIT
D[7:0]
DOUT
RDY
01234
BYTE 0 BYTE 1
TINIT_CLK
TCH
TCL
TH
TS
TD
5 6 7 0
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 165
Timing Characteristics (continued)
Note: Serial configuration data is transmitted out on DOUT on the falling edge of CCLK after it is input on DIN.
Note: Serial configuration data is transmitted out on DOUT on the falling edge of CCLK after it is input on DIN
Figure 70. Slave Serial Configuration Mode Timing Diagram
Table 52A. OR2CxxA/OR2TxxA Slave Serial Configuration Mode Timing Characteristics
OR2CxxA Commer ci al : VDD = 5.0 V ± 5%, 0 °C ≤ TA ≤ 70 °C; OR2CxxA Industrial: VDD = 5.0 V ± 10%, –40 °C ≤ TA ≤ +85 °C.
OR2Txx A Co mm erc ial : VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; O R2TxxA Industrial: VDD = 3.0 V to 3.6 V, –40 °C ≤ TA ≤ +85 °C
Parameter Symbol Min Max Unit
DIN Setup Time TS20 — ns
DIN Hold Time TH0—ns
CCLK High Time TCH 50 — ns
CCLK Low Time TCL 50 — ns
CCLK Frequency FC—10MHz
CCLK to DOUT TD—30ns
Table 52B. OR2TxxB Slave Serial Configuration Mode Timing Characteristics
OR2Tx xB C ommer cial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2TxxB Indust rial: VDD = 3.0 V to 3.6 V, –40 °C ≤ TA ≤ +85 °C.
Parameter Symbol Min Max Unit
DIN Setup Time TS15 — ns
DIN Hold Time TH0—ns
CCLK High Time TCH 12.5 — ns
CCLK Low Time TCL 12.5 — ns
CCLK Frequency FC—40MHz
CCLK to DOUT TD—10ns
5-4535(F)
DIN
CCLK
DOUT
TD
TSTH
TCL TCH
BIT N
BIT N
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
166 Lucent Technologies Inc.
Timing Characteristics (con tinued)
Note: Daisy chaining of FPGAs is not supported in this mode.
Note: Daisy chaining of FPGAs is not supported in this mode.
Figure 71. Slave Parallel Configuration Mode Timing Diagram
Table 53A. OR2CxxA/OR2TxxA Slave Parallel Configuration Mode Timing Characteristics
OR2CxxA Commer ci al : VDD = 5.0 V ± 5%, 0 °C ≤ TA ≤ 70 °C; OR2CxxA Industr ial: VDD = 5.0 V ± 10%, –40 °C ≤ TA ≤ +85 °C.
OR2TxxA Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2Txx A Industrial: VDD = 3.0 V to 3.6 V, –40 °C ≤ TA ≤ +85 °C.
Parameter Symbol Min Max Unit
CS0, CS1, WR Setup Time TS1 60 — ns
CS0, CS1, WR Hold Time TH1 20 — ns
D[7:0] Setup Time TS2 20 — ns
D[7:0] Hold Time TH2 0—ns
CCLK High Time TCH 50 — ns
CCLK Low Time TCL 50 — ns
CCLK Frequency FC—10MHz
Table 53B. OR2TxxB Slave Parallel Configuration Mode Timing Characteristics
OR2TxxB Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2Txx B Industrial: VDD = 3.0 V to 3.6 V, –40 °C ≤ TA ≤ +85 °C.
Parameter Symbol Min Max Unit
CS0, CS1, WR Setup Time TS1 ———
CS0, CS1, WR Hold Time TH1 15 — ns
D[7:0] Setup Time TS2 15 — ns
D[7:0] Hold Time TH2 0—ns
CCLK High Time TCH 12.5 — ns
CCLK Low Time TCL 12.5 — ns
CCLK Frequency FC—40MHz
5-2848(F)
TS1 TH1
TS2 TH2
CS1
CCLK
D[7:0]
CS0
WR
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 167
Timing Characteristics (continued)
Figure 72. Readback Timing Diagram
Table 54. Series 2 Readback Timing Characteristics
OR2CxxA Commer ci al : VDD = 5.0 V ± 5%, 0 °C ≤ TA ≤ 70 °C; OR2CxxA Industrial: VDD = 5.0 V ± 10%, –40 °C ≤ TA ≤ +85 °C.
OR2TxxA/B Commercia l: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2T x xA/B Industrial: VDD = 3.0 V to 3.6 V,
–40 °C ≤ TA ≤ +85 °C.
Parameter Symbol Min Max Unit
RD_CFGN to CCLK Setup Time TS50 — ns
RD_CFGN High Width to Abort Readback TRBA 2—CCLK
CCLK Low Time TCL 50 — ns
CCLK High Time TCH 50 — ns
CCLK Frequency FC—10MHz
CCLK to RD_DATA Delay TD—50ns
5-4536(F)
TD
TCH
CCLK
RD_DATA
TSTCL
RD_CFGN
BIT 0 BIT 1 BIT 0
TRBA
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
168 Lucent Technologies Inc.
Timing Characteristics (continued)
BSTD(F).2c.r3
Figure 73. Boundary-Scan Timing Diagram
Table 55. Series 2 Boundary-Scan Timing Characteristics
OR2CxxA Commer ci al : VDD = 5.0 V ± 5%, 0 °C ≤ TA ≤ 70 °C; OR2CxxA Industr ial: VDD = 5.0 V ± 10%, –40 °C ≤ TA ≤ +85 °C.
OR2TxxA Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2Txx A Industrial: VDD = 3.0 V to 3.6 V, –40 °C ≤ TA ≤ +85 °C.
OR2TxxB Commercial: VDD = 3.0 V to 3.6 V, 0 °C ≤ TA ≤ 70 °C; OR2Txx B Industrial: VDD = 3.0 V to 3.6 V, –40 °C ≤ TA ≤ +85 °C.
Parameter Symbol Min Max Unit
TDI/TMS to TCK Setup Time TS25 — ns
TDI/TMS Hold Time from TCK TH0—ns
TCK Low Time TCL 50 — ns
TCK High Time TCH 50 — ns
TCK to TDO Delay TD—20ns
TCK Frequency TTCK —10MHz
TCK
TMS
TDI
TDO
TSTH
TD
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 169
Measurement Conditions
5-3234(F).r1
Figure 74. ac Test Loads
5-3233(F).ar4
Figure 75. Output Buffer Delays
5-3235(F).a
Figure 76. Input Buffer Delays
50 pF
A. Load Used to Measure Propagation Dela y
TO THE OUTPUT UNDER TEST
TO THE OUTPUT UNDER TEST
50 pF
VCC GND
1 kΩ
B. Load Used to Measure Rising/Falling Edges
VDD
TPHH
VDD/2
VSS
OUT[I]
PAD
OUT 1.5 V
0.0 V TPLL
PAD
OUT[I] ac TEST LOADS (SHOWN ABOVE)
TS[I]
OUT
0.0 V
1.5 V
TPHH TPLL
PAD IN[I]
IN
3.0 V
VSS
VDD/2
VDD
PAD IN
IN[I]
Lucent Technologies Inc. 170
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Output Buffer Characteristics
OR2CxxA
5-4634(F)
Figure 77. Sinklim (TJ = 25 °C, VDD = 5.0 V)
5-4636(F)
Figure 78. Slewlim (TJ = 25 °C, VDD = 5.0 V)
5-4638(F)
Figure 79. Fast (TJ = 25 °C, VDD = 5.0 V)
5-4635(F)
Figure 80. Sinklim (TJ = 125 °C, V DD = 4.5 V)
5-4637(F)
Figure 81. Slewlim (TJ = 125 °C, VDD = 4.5 V)
5-4639(F)
Figure 82. Fast (TJ = 125 °C, VDD = 4.5 V)
70
60
50
40
30
20
10
0
OUTPUT CURRENT, I
O
(mA)
012345
OUTPUT V OLTAGE, V
O
(V)
I
OL
I
OH
250
225
150
100
50
0
OUTPUT CURRENT, I
O
(mA)
01234
OUTPUT VO LTAGE, V
O
(V)
I
OL
I
OH
5
200
175
125
75
25
250
225
150
100
50
0
OUTPUT CURRENT, I
O
(mA)
01234
OUTPUT VO LTAGE, V
O
(V)
I
OL
I
OH
5
200
175
125
75
25
50
40
30
20
10
0
OUTPUT CURRENT, I
O
(mA)
01234
OUTPUT VOLTAGE, V
O
(V)
I
OL
I
OH
5
150
125
100
75
50
0
OUTPUT CURRENT, I
O
(mA)
01 2 3 4
OUTPUT V OLTAGE, V
O
(V)
I
OL
I
OH
25
175
125
100
75
50
0
OUTPUT CURRENT, I
O
(mA)
01 2 3 4
OUTPUT VOLTAGE, V
O
(V)
I
OL
I
OH
25
150
171 Lucent Technologies Inc.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
Output Buffer Characteristics (continued)
OR2TxxA
5-4637(F)
Figure 83. Sinklim (TJ = 25 °C, VDD = 3.3 V)
5-4637(F)
Figure 84. Slewlim (TJ = 25 °C, VDD = 3.3 V)
5-4637(F)
Figure 85. Fast (TJ = 25 °C, VDD = 3.3 V)
5-4637(F)
Figure 86. Sinklim (TJ = 125 °C, VDD = 3.0 V)
5-4637(F)
Figure 87. Slewlim (TJ = 125 °C, VDD = 3.0 V)
5-4637(F)
Figure 88. Fast (TJ = 125 °C, VDD = 3.0 V)
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5
0
20
40
60
80
OUTPU T VOLT AGE, V
O
(V)
I
OL
70
50
30
10
I
OH
OUTPUT CURRENT, I
O
(mA)
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5
0
60
100
120
140
OUTPU T VOLTAGE, V
O
(V)
OUTPUT CURRENT, I
O
(mA)
I
OL
I
OH
80
40
20
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5
0
60
100
120
140
OUTPU T VOLTAGE, V
O
(V)
OUTPUT CURRENT, I
O
(mA)
I
OL
I
OH
80
40
20
0.0 0.5 1.0 1.5 2.0 2.5 3.0
0
5
10
30
40
OUTPUT VOLTAGE, V
O
(V)
OUTPUT CURRENT, IO (mA)
I
OL
I
OH
25
20
15
35
0.0 0.5 1.0 1.5 2.0 2.5 3.0
0
10
20
70
OUTPUT VOLTAGE, V
O
(V)
OUTPUT CURRENT, I
O
(mA)
I
OL
I
OH
50
40
30
60
0.0 0.5 1.0 1.5 2.0 2.5 3.0
0
10
20
70
OUTPUT VOLTAGE, V
O
(V)
OUTPUT CURRENT, I
O
(mA)
I
OL
I
OH
50
40
30
60
Lucent Technologies Inc. 172
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Output Buffer Characteristics (continued)
OR2TxxB
5-7927(F).r1
Fi
g
ure 89. Sinklim
(
TJ = 25 °C, VDD = 3.3 V
)
5-7928(F).r1
Fi
g
ure 90. Slewlim
(
TJ = 25 °C, VDD = 3.3 V
)
5-7929(F).r1
Figure 91. Fast (TJ = 25 °C, VDD = 3.3 V)
5-7930(F).r1
Fi
g
ure 92. Sinklim
(
TJ = 125 °C, VDD = 3.0 V
)
5-7931(F).r1
Fi
g
ure 93. Slewlim
(
TJ = 125 °C, VDD = 3.0 V
)
5-7932(F).r1
Fi
g
ure 94. Fast
(
TJ = 125 °C, VDD = 3.0 V
)
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5
90
80 IOL
60
50
40
30
20
10
0
OUTPUT VO LT AG E, VO (V)
OUTPUT CURRENT, IO (mA)
IOH
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5
180
160
140
120
100
80
60
40
20
0
OUTPUT VOLTAGE, VO (V)
OUTPUT CURRENT, IO (mA)
IOL
IOH
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5
180
160
140
120
100
80
60
40
20
0
OUTPUT VOLTAGE, VO (V )
OUTPUT CURRENT, IO (mA)
IOL
IOH
0.0 0.5 1.0 1.5 2.0 2.5 3.0
55
50
40
30
25
20
15
10
05
0
OUTPUT VOLTAGE , V O (V)
OUTPUT CURRENT, IO (mA)
45
35
IOL
IOH
0.0 0.5 1.0 1.5 2.0 2.5 3.0
110
100
80
60
50
40
30
20
10
0
OUTPUT VOLTAGE, VO (V )
OUTPUT CURRENT, IO (mA)
90
70
IOL
IOH
0.0 0.5 1.0 1.5 2.0 2.5 3.0
110
100
80
60
50
40
30
20
10
0
OUTPUT VOLTAGE, VO (V )
OUTPUT CURRENT, IO (mA)
90
70
IOL
IOH
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 173
Package Outline Drawings
Term s and Definitions
Basic Size (BSC): The basic size of a dimension is the size from which the limits f or that dimension are deriv ed
by the application of the allowance and the tolerance.
Design Size: The design size of a dimension is the actual size of the design, including an allowance for fit
and tolerance.
Minimum (MIN) or
Maximum (MAX): Indicates the minimum or maximum allow able size of a dimension.
Ref erence (REF): The reference dimension is an untoleranced dimension used for inf ormational purposes only.
It is a repeated dimension or one that can be derived from other values in the drawing.
Typical (TYP): When specified after a dimension, this indicates the repeated design size if a tolerance is
specified or repeated basic size if a tolerance is not specified.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
174 Lucent Technologies Inc.
Package Outline Drawings (continued)
84-Pin PLCC
Dimensions are in millimeters.
5-2347r.16
1.27 TYP 0.330/0.533
0.10
SEATING PLANE
0.51 MIN
TYP
5.080
MAX
PIN #1 IDENTIFIER ZONE
11 75
5333
12
32 54
74
29.083 ± 0.076
30.353 MAX
30.353
MAX
1
29.083
± 0.076
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 175
Package Outline Drawings (continued)
100-Pin TQFP
Dimensions are in millimeters.
5-2146r.15
0.50 TYP
1.60 MAX
SEATING PLANE
0.08
1.40 ± 0.05
0.05/0.15
DETAIL A DETAIL B
14.00 ± 0.20
16.00 ± 0.20
76100
1
25
26 50
51
75
14.00
± 0.2 0
16.00
± 0.20
PIN #1 IDENTIFIER ZONE
DETAIL B
0.19/0.27
0.08 M
0.106/0.200
DETAIL A
0.45/0.75
GAGE PLANE
SEATI N G PLA N E
1.00 REF
0.25
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
176 Lucent Technologies Inc.
Package Outline Drawings (continued)
144-Pin TQFP
Dimensions are in millimeters.
5-3815r.5
DETAIL B
0.19/0.27
0.08 M
0.106/0.200
DETAIL A
0.45/0.75
GAGE PLAN E
SEATING PLANE
1.00 REF
0.25
1.60 MAX
SEATING PLANE
0.08
0.50 TYP
1.40 ± 0.05
0.05/0.15
DETAIL A DETAIL B
PIN #1 IDENTIFIER ZONE
20.00 ± 0.20
22.00 ± 0.20
109144
1
36
37 72
73
108
20.00
± 0.20
22.00
± 0.20
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 177
Package Outline Drawings (continued)
160-Pin QFP
Dimensions are in millimeters.
5-2132r.12
81
120
28.00
± 0.2031.20
± 0.20
DETAIL A DETAIL B
4.07 MAX
0.65 TYP
SEATING PLANE
0.10
3.42 ± 0.25
0.25 MIN
1
40
121160 PIN #1 IDENTIFIER ZONE
31.20 ± 0.20
28.00 ± 0.20
8041
0.22/0.38
0.12 M
0.13/0.23
DETAIL B
0.25
0.73/1.03
1.60 REF
GAGE PLANE
SEATING PLANE
DETAIL A
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
178 Lucent Technologies Inc.
Package Outline Drawings (continued)
208-Pin SQFP
Dimensions are in millimeters.
5-2196r.13
156
105
30.60 ± 0.20
157208
1
52
53 104
28.00 ± 0.20
28.00
± 0.20
30.60
± 0.20
PIN #1 IDENTIFIER ZONE
4.10 MAX
0.08
3.40 ± 0.20
SEATING PLA NE
0.25 MIN
0.50 TYP
DETAIL BDETAIL A
0.50/0.75
GAGE PLAN E
SEATING PLANE
1.30 REF
0.25
DETAIL A DETAIL B
0.17/0.27
0.10 M
0.090/0.200
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 179
Package Outline Drawings (continued)
208-Pin SQFP2
Dimensions are in millimeters.
5-3828.a
156
105
30.60 ± 0.20
157
208
1
52
53 104
28.00 ± 0.20
EXPOSE D HEAT SI NK APPEARS ON BO T TOM
SURFACE: CHIP BONDED FACE UP (SEE DETAIL C)
28.00
± 0.20
30.60
± 0.20
PIN #1 IDENTIFIER ZONE
21.0
REF
21.0 REF
4.10 MAX
0.08
3.40 ± 0.20
SEATING PLA NE
0.25 MIN
0.50 TYP
DETAIL B
DETAIL A
0.50/0.75
GAGE PLANE
SEATING PLA NE
1.30 REF
0.25
DETAIL A DETAIL B
0.17/0.2
0.10 M
0.090/0.200
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
180 Lucent Technologies Inc.
Package Outline Drawings (continued)
240-Pin SQFP
Dimensions are in millimeters.
5-2718r.8
0.08
3.40 ± 0.20
S EATIN G PLA NE
0.25 MIN
0.50 TYP
DETAIL A DETAIL B
180
121
181240
34.60 ± 0.20
1
32.00 ± 0.20
60
61 120
PIN #1 IDENTIFIER ZONE
32.00
± 0.20
0.50/0.75
GAGE PLANE
SEATI N G PLA N E
1.30 REF
0.25
DETAIL A DETAIL B
0.17/0.27
0.10 M
0.090/0.200
4.10 MAX
34.60
± 0.20
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 181
Package Outline Drawings (continued)
240-Pin SQFP2
Dimensions are in millimeters.
5-3825r.8
0.50/0.75
GAGE PLANE
SEATING PLANE
1.30 REF
0.25
DETAIL A
DETAIL B
0.17/0.27
0.10 M
0.090/0.200
CHIP
CHIP BONDED FACE UP
COPPER HEAT SINK
0.08
3.40 ± 0.20
SEATING PLANE
0.25 MIN
0.50 TYP
DETAIL A DETAIL B
180
121
181240
34.60 ± 0.20
1
32.00 ± 0.20
60
61 120
PIN #1 IDENTIFIER ZONE
32.00
± 0.20
34.60
± 0.20
EXPO SED HEAT SINK APPEAR S ON
TOP SURFACE IN CHIP FACE-DOWN VERSION OR
BOTTOM SURFACE IN CHIP FACE-UP VERSION
24.2
REF
24.2 REF
4.10 MAX
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
182 Lucent Technologies Inc.
Package Outline Drawings (continued)
256-Pin PBGA
Dimensions are in millimeters.
5-4406r.6
0.36 ± 0.04 1.17 ± 0.05 2.13 ± 0.19
SEATING PLANE
SOLDER BALL
0.60 ± 0.10
0.20
PWB
MOLD
COMPOUND
27.00 ± 0.20
27.00
± 0.20
24.00 +0.70
–0.00
24.00 +0.70
–0.00
A1 BALL
IDENTIFIER ZONE
A
B
C
D
E
F
G
H
J
K
L
M
Y
N
P
R
T
U
V
W
12345678910
1112131415161718 20
19
CENTER ARRAY
FOR THERMAL
ENHANCEMENT
19 SPACES @ 1.27 = 24.13
A1 BALL
CORNER
19 SPACES
@ 1.27 = 24.13
0.75 ± 0.15
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 183
Package Outline Drawings (continued)
304-Pin SQFP
Dimensions are in millimeters.
5-3307r.8
DETAIL A DETAIL B
4.10 MAX
0.50 TYP
SEATING PLA NE
0.08
3.40 ± 0.20
0.25 MIN
0.17/0.27
0.10 M
0.090/0.200
DETAIL B
0.25
0.50/0.75
1.30 REF
GAGE PLANE
SEATING PLA NE
DETAIL A
PIN #1 IDENTIFIER ZONE
42.60 ± 0.20
40.00 ± 0.20
42.60
± 0.20
40.00
± 0.20
1
76
77 152
153
228
229304
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
184 Lucent Technologies Inc.
Package Outline Drawings (continued)
304-Pin SQFP2
Dimensions are in millimeters.
5-3827(F).r8
DETAIL A DETAIL B
4.10 MAX
0.50 TYP
SEATING PLANE
0.08
3.40 ± 0.20
0.25 MIN
0.17/0.27
0.10 M
0.090/0.200
DETAIL B
0.25
0.50/0.75
1.30 REF
GAGE PLANE
SEATING PLANE
DETAIL A
42.60 ± 0.20
40.00 ± 0.20
42.60
± 0.20
40.00
± 0.20
1
76
77 152
153
228
229304 PIN #1 IDENTIFIER ZONE
EXPOSED HEAT SINK APPEARS ON
TOP SURFACE IN CHIP FACE-DO WN VER SION OR
BOTTOM SURFAC E IN CHIP FACE-UP VERSION
31.2 REF
31.2
REF
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 185
Package Outline Drawings (continued)
352-Pin PBGA
Dimensions are in millimeters.
5-4407r.4
0.56 ± 0.06 1.17 ± 0.05 2.33 ± 0.21
SEATING PLANE
SOLDER BALL
0.60 ± 0.10 0.20
PWB
MOLD
COMPOUND
35.00
+0.70
–0.00
30.00
A1 BALL
IDENTIFIE R ZONE
AF
AE
AD
AC
AB
AA
Y
W
V
U
T
R
G
25 SPACES @ 1.27 = 31.75
P
N
M
L
K
J
H
1 2 3 4 5 6 7 8 9 10 12 14 16 18 22 24 2620
11 13 15 17 2119 23 25
F
E
D
C
B
A
CENTER ARRAY
25 SPACES
A1 BALL
0.75 ± 0.15
35.00 ± 0.20
30.00 +0.70
–0.00
± 0.20
@ 1.27 = 31.75
FOR THERMAL
ENHANCEMENT
CORNER
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
186 Lucent Technologies Inc.
Package Outline Drawings (continued)
432-Pin EBGA
Dimensions are in millimeters.
5-4409r.3
0.91 ± 0.06 1.54 ± 0.13
SEATING PLANE
SOLDER BALL
0.63 ± 0.07
0.20
40.00 ± 0.10
40.00
A1 BALL
M
D
AG
B
F
K
HG
E
AD
L
T
J
N
AJ
C
Y
P
AH
AE
AC
AA
W
U
R
AK
AF
AB
V
AL
A
19 3026
528242223 25720 312915 21
18
32711 17
4 6 81012141629131
30 SPACES @ 1.27 = 38.10
30 SPACES
A1 BALL
0.75 ± 0.15
IDENTIFIER ZONE
± 0.10
@ 1.27 = 38.10
CORNER
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 187
Ordering Information
OR2C12A, -4 speed grade, 240-pin shrink quad flat pack, commercial temperature.
Table 56. FPGA Voltage Options
Device Voltage
OR2CxxA 5.0 V
OR2TxxA 3.3 V
OR2TxxB 3.3 V
Table 57. FPGA Temperature Options
Symbol Description Temperature
(Blank) Commercial 0 °C to 70 °C
I Industrial –40 °C to +85 °C
Table 58. FPGA Package Options
Symbol Description
BA Plastic Ball Grid Array (PBGA )
BC Enhanced Ball Grid Array (EBGA)
J Quad Flat Package (QFP)
M Plastic Leaded Chip Carrier (PLCC)
PS Power Quad Shrink Fl at Packag e (SQFP2)
S Shrink Quad Flat Package (SQFP)
T Thin Quad Flat Package (TQFP)
OR2C 12A-4 S 240
DEVICE TYPE
SPEED GRADE PACKAGE TYPE
NUMB ER OF PI NS
TEMPERAT URE RANGE
Example:
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
188 Lucent Technologies Inc.
Ordering Information (continued)
Key: C = commercial, I = industrial.
Key: C = commercial, I = industrial.
Notes:
The package options with the SQFP/SQFP2 designation in the table above use the SQFP package for all densities up to and inc luding the
OR2C/T15A/B , while the OR2C/T26A and the OR2C/2T40A/B use the SQFP2.
The OR2TxxA and OR2TxxB series is not offered in the 304-pin SQFP/SQFP2 packages.
The OR2C40A is not offered in a 352-pin PBGA.
Table 59.
ORCA
OR2CxxA/OR2TxxA
Series
Package Matrix
Packages 84-Pin
PLCC 100-Pin
TQFP 144-Pin
TQFP 160-Pin
QFP
208-Pin
EIAJ
SQFP/
SQFP2
240-Pin
EIAJ
SQFP/
SQFP2 256-Pin
PBGA
304-Pin
EIAJ
SQFP/
SQFP2 352-Pin
PBGA 432-Pin
EBGA
M84 T100 T144 J160 S208/
PS208 S240/
PS240 BA256 S304/
PS304 BA352 BC432
OR2C/2T04A CI CI CI CI CI — — — — —
OR2C/2T06A CI CI CI CI CI CI CI — — —
OR2C/2T08A CI — — CI CI CI CI — — —
OR2C/2T10A CI — — CI CI CI CI — CI —
OR2C/2T12ACI———CICICICICI—
OR2C/2T15ACI———CICICICICICI
OR2C/2T26A————CICI—CICICI
OR2C/2T40A ————CICI—CICICI
Table 60.
ORCA
OR2TxxB
Series
Package Matrix
Packages 84-Pin
PLCC 100-Pin
TQFP 144-Pin
TQFP 160-Pin
QFP
208-Pin
EIAJ
SQFP/
SQFP2
240-Pin
EIAJ
SQFP/
SQFP2 256-Pin
PBGA
304-Pin
EIAJ
SQFP/
SQFP2 352-Pin
PBGA 432-Pin
EBGA
M84 T100 T144 J160 S208/
PS208 S240/
PS240 BA256 S304/
PS304 BA352 BC432
OR2T15B————CICICI—CI—
OR2T40B————CICI——CICI
189 Lucent Technologies Inc.
Data Sheet
ORCA
Seri es 2 FPGAs June 19 99
Index
A
Absolute Maximum Ratings, 129
Adder (see LUT Operating Modes)
Architecture
Overview, 5
PLC, 22
PIC, 25
B
Bidirectional Buffers (BIDIs), 14, 17, 18, 20, 22
(see also Routing and SLIC)
Bit Stream (see FPGA Configuration)
Bit Stream Error Checking, 47
(see also FPGA States of Operation)
Boundary Scan, 54—59
C
Clock Distribution Network, 37—39
Selecting Clock Input Pins, 39
Clock Enable (CE), 1, 5, 7, 15, 16, 24, 134
Comparator (see LUT Operating Modes)
Configuration (see FPGA States of Operation
or FPGA Configuration)
Control Inputs, 5, 7
E
Electrical Characteristics, 130
Error Checking (see FPGA Configuration)
F
5 V Tolerant I/O, 26—27, 64
FPGA Configuration
Configuration Frame Format, 43—46
Configuration Modes, 47, 158—160
Asynchronous Peripheral Mode, 49, 163
Daisy-Chaining, 51
Master Parallel Mode, 47
Master Serial Mode, 162
Slave Parallel Mode, 48, 50, 161, 166
Slave Serial Mode, 49—50, 165
Synchronous Peripheral Mode, 48, 164
Data Format, 43—45
Using
ORCA
Foundry to Generate RAM Data, 43
FPGA States of Operation, 40—43
Configuration, 41
Initialization, 40
Other Configuration Options, 43
Partial Recon fig urati on, 43
Reconfiguration, 42
Start-Up, 41
G
GSR (see GSRN)
GSRN, 6, 7, 16, 37, 134
I
IEEE
Standard 1149.1, 1
(see also Boundary Scan)
Initialization (see FPGA States of Operation)
Input/Output Buffers (see PICs)
Measurement Conditions, 169
Output Buffer Characteristics, 170—172
J
JTAG (see Boundary Scan)
L
Look-up Table (LUT) Operating Modes, 7—15
Adder-Subtractor Submode, 10
Counter Submode, 11
Equality Comparators, 11
Logic Mode s, 7—9
Memory Mode, 12— 15
Async hrono us Memory, 12
Synchronous Memory, 13
Multiplier Submode, 11
Ripple Mode, 10
LSR, 5—7, 15—16
M
Maximum Ratings (see Absolute Maximum Ratings)
Multiplier (see LUT Operating Modes)
O
ORCA
Foundry Development System Overview, 4
Ordering Information, 189
Package Matrix, 190
Package Options, 189
Temperature Options, 189
Voltage Options, 189
Output (see PICs)
P
Package Outline Drawings, 174—186
Pack age Matrix, 190
Package Outline Drawings, 173
84-Pin PLCC, 174
100-Pin TQFP, 175
144-Pin TQFP, 176
Lucent Technologies Inc. 190
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Index (continued)
160-Pin QFP, 177
208-Pin SQFP, 178
208-Pin SQFP2, 179
240-Pin SQFP, 180
240-Pin SQFP2, 181
256-Pin PBGA, 182
304-Pin SQFP, 183
304-Pin SQFP2, 184
352-Pin PBGA, 185
432-Pin EBGA, 186
Terms and Definitions, 173
Pin Information, 71—125
84-Pin PLCC, 71
100-Pin TQFP, 73
144-Pin TQFP, 75
160-Pin QFP, 77
208-Pin SQFP/SQFP2, 81
240-Pin SQFP/SQFP2, 86
256-Pin PBGA, 92
304-Pin SQFP/SQFP2, 99
352-Pin PBGA, 106
432-Pin EBGA Pinout, 116
Package Compatibility, 68—70
Pin Descriptions, 71
Power Dissip ati on, 61—6 5
5 V Tolerant I/O, 64
OR2CxxA, 61
OR2TxxA, 63
Programmable Function Unit (PFU), 5—16
Control Inputs, 5, 7
Operating Modes, 7—15
Latches/Flip-Flops, 15—16
Programmable Input/Output Cells (PICs), 25—31
5 V Tolerant I/O, 26
Architecture, 29—30
Inputs, 25
Outputs, 26
Open-Drain Output Option, 26
Propagation Delays, 26
Overview, 25
Zero-Hold Input, 25
Programmable Logic Cells (PLCs), 5—24
Architecture, 22—24
Latches/Flip-Flops, 15—16
PFU, 5—16
Routing, 17—24
R
RAM ( see also F P GA Configuration), 17, 44, 135, 142
Dual-port, 3, 7, 13—15
Single-port, 3, 7, 12—15
Recommen ded Op er ati ng Cond itions , 129
Reconfiguration (see FPGA States of Operation)
Routing
3-Statable Bidirectional Buffers, 17—18, 148
Clock Routing, 24, 149—153
(see also Clock Distribution Network)
Configurable Interconnect Points (CIPs), 17
Fast-Carry Routing, 24
Inter-PLC Routing Resources, 18—19
Interquad Routing, 5, 17, 32—36
Intra-PLC Routing Resources, 18
Minimizing Routing Delay, 20
PLC Routing, 17—24, 34
Programmable Corner Cell Routing, 37
PIC Routing, 27—31
S
Bound ary Sc an, 54– 59
Global 3-State Control (TS_ALL), 37, 66
Global Set/Reset (GSRN), 7, 16, 37
Internal Oscillator, 37
Readback Logic, 37
Start-up, 41 (see also FPGA States of Operation)
Subtractor (see LUT Operating Modes)
System Clock (see Clock Distribution Network)
T
3-state (see Bidi re cti on al Buf f ers, TS_ALL)
Timing Characteristics, 132–168
Asynchronous Peripheral Configuration Mode, 163
Bou ndary-Scan Timing, 168
Clock Timing, 149
General Configuration Mode Timing, 158
Master Paral le l Confi guration Mode, 162
Master Seri al Conf igu ra tio n Mode, 161
PFU Timing, 132
PIO Timing, 154
PLC Timing, 148
Readback Timing, 1 67
Slave Parallel Configuration Mode, 166
Slave Serial Configuration Mode, 165
Tolerant I/O, 26 (see also 5 V Tolerant I/O)
TS_ALL, 1, 37, 66
U—Z
Zero-hold Inputs, 25
Data Sheet
J une 1999
ORCA
Series 2 FPGAs
Lucent Technologies Inc. 191
Notes
Lucent Technologies Inc. reserves the right to make changes to the product(s) or infor mation contained herein without notice. No liability is assumed as a result of their use or application. No
rights under any patent accompany the sale of any such product(s) or information.
ORCA
is a registered trademark of Lucent Technologies Inc. Foundry is a trademark of Xilinx Inc.
Copyright © 1999 Lucent Technologies Inc.
All Rights Reserved
June 1999
DS99-094FPGA (Replaces DS98-022FPGA )
For additional information, contact your Microelectronics Group Account Manager or the following:
INTERNET: http://www.lucent.com/micro or for FPGA information, http://www.lucent.com/orca
E-MAIL: docmaster@micro.lucent.com
N. AMERICA: Microe lectronics Group, Lucent Technolo gies Inc., 555 Union Boulevard, Room 30L-15P-BA, Allen town, PA 18103
1-800-372-2447, FAX 610 -712-4106 (In CANA DA: 1-800-553-2448, FAX 610-712-4106)
ASIA PACIFIC: Microelectronics Group, Lucent Technologies Singapore Pte. Ltd., 77 Science Park D rive, #03 -18 Ci ntech III, Singapore 118256
Tel. (65) 778 8833, FAX (65) 777 7495
CHIN A: Microelectronics Gr oup, Lucent Technologies (China) Co., Lt d . , A - F 2, 23/F, Zao Fong Uni verse Building, 180 0 Zhong Shan Xi Road, Shanghai
200233 P. R. China Tel. (86) 21 644 0 0468, ext. 316, FAX (86) 21 6440 0652
JAPAN: Microelectronics Group, Lucent Technologies Japan Ltd., 7-18, Higashi-Gotanda 2-chome, Shinagawa-ku, Tokyo 141, Japan
Tel. (81) 3 5421 1600, FA X (81) 3 5421 1700
EUROPE: Data Requests: MICROELECTRONICS GROUP DATALINE: Tel. (44) 1189 324 299, FAX (44) 1189 328 148
Technical Inquiries: GERMAN Y: (49) 89 95086 0 (Munich), UNITED KIN G DOM: (44) 13 44 865 900 (Ascot),
FRANCE: (33) 1 40 83 68 00 (Paris), SWEDEN: (46) 8 594 607 00 (Stockholm), FINLAND: (358) 9 4354 2800 (Helsinki),
ITALY: (39) 02 6608131 (Milan), SPAIN : ( 34) 1 807 1441 (Madrid)
